This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
development cycle:
- Get rid of the .disable() callback from the driver callback
vtable. This callback was abused and counterintuitive since
a pin or group of pins can be said to always be in some
setting, and never really disabled. We now only enable a
certain muxing, and move between some certain muxings, we
never "disable" a mux setting.
- Some janitorial moving the MSM, Samsung and Nomadik and
drivers to their own subdirectories for a clearer view in
the subsystem. This will continue.
- Kill off the use of the return value from gpiochip_remove(),
this will be done in parallel in the GPIO subsystem and
hopefully not trigger too many unchecked return value
warnings before we get rid of this altogether.
- A huge set of changes and improvements to the Allwinner
sunxi drivers especially for their latest A23 and A31 SoCs,
and some ground work for the new sun8i platform family.
- A large set of Rockchip driver improvements adding support
for the RK3288 SoC.
- Advances in migration of older Freescale platforms to pin
control, especially i.MX1.
- Samsung and Exynos improvements.
- Support for the Qualcomm MSM8960 SoC.
- Use the gpiolib irqchip helpers for the ST SPEAr and
Intel Baytrail drivers.
- A bunch of nice janitorial work done with cppcheck.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT41HwAAoJEEEQszewGV1zVN0QAMJOJcsjYyHG+b/y0upJ5n1c
tyPelyxKrpGUUTvTsO5LiqvoIfa2E/DrwXupRAC4zAXvb+x3TUGkiluK4Yxl5e56
AqjePnSydqqHiRZOK4Q06W7VwGUoxLltDmDPTcra+DAaijIeKUPMQE1MvcPxisMe
IR7PZN58JYCG3ZV5yjwfBBxcRAm8KiiwHvQdBywPIGGvvmpy1X+U96U869nQgUH2
70lpJVPx75bhyAFk99bE9nAnroZeRR7mvijjf26ssyAFNqeJ0K7Xlom+NtpHdiw0
lsDKdBiAWVbZON/7Pc24gpHzhBoIYdA/6LxPA8Xz4QVFRmfxmNkZhuXZnZ7Dbuj2
xv9HtnjExqjZcfeNyUlO0iQDEQIUN/oPkaBS2G8DNZ/bmQqC8EzkIFh6F72KO1s2
7FU214LcuBYuAa3HvNLmgtjSkgou8tTMj58rnZ1XDr2mI9tzlrwI3i6ZrJZWKDur
NIoRAcUZkFiMpXxqLbk4UXzDvuJgrzaFiQ2PkxTXAlC2DjXz+gXPzPIOSD5LTaHE
k3WvZfuGK2iPoKeDHaLx2qEl9PoD5hz1JH3o+bgOKkRZG2gEJWd02JwhuPyRPLfc
TeBgmdYS2t2MBS21VsqoObw8336oCHJu7tDAxTkAalLsZy9MV2WqThhZoYggZ/Rq
yMqCr8vfd2pRVtwYe7Wc
=t1pR
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"This is the bulk pin control changes for the v3.17 merge development
cycle:
- get rid of the .disable() callback from the driver callback vtable.
This callback was abused and counterintuitive since a pin or group
of pins can be said to always be in some setting, and never really
disabled. We now only enable a certain muxing, and move between
some certain muxings, we never "disable" a mux setting
- some janitorial moving the MSM, Samsung and Nomadik and drivers to
their own subdirectories for a clearer view in the subsystem. This
will continue
- kill off the use of the return value from gpiochip_remove(), this
will be done in parallel in the GPIO subsystem and hopefully not
trigger too many unchecked return value warnings before we get rid
of this altogether
- a huge set of changes and improvements to the Allwinner sunxi
drivers especially for their latest A23 and A31 SoCs, and some
ground work for the new sun8i platform family
- a large set of Rockchip driver improvements adding support for the
RK3288 SoC
- advances in migration of older Freescale platforms to pin control,
especially i.MX1
- Samsung and Exynos improvements
- support for the Qualcomm MSM8960 SoC
- use the gpiolib irqchip helpers for the ST SPEAr and Intel Baytrail
drivers
- a bunch of nice janitorial work done with cppcheck"
* tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (61 commits)
pinctrl: baytrail: Convert to use gpiolib irqchip
pinctrl: sunxi: number gpio ranges starting from 0
pinctrl: sunxi: use gpiolib API to mark a GPIO used as an IRQ
pinctrl: rockchip: add drive-strength control for rk3288
pinctrl: rockchip: add separate type for rk3288
pinctrl: rockchip: set is_generic in pinconf_ops
pinctrl: msm: drop negativity check on unsigned value
pinctrl: remove all usage of gpio_remove ret val in driver/pinctl
pinctrl: qcom: Make muxing of gpio function explicit
pinctrl: nomadik: move all Nomadik drivers to subdir
pinctrl: samsung: Group all drivers in a sub-dir
sh-pfc: sh73a0: Introduce the use of devm_regulator_register
sh-pfc: Add renesas,pfc-r8a7791 to binding documentation
pinctrl: msm: move all qualcomm drivers to subdir
pinctrl: msm: Add msm8960 definitions
pinctrl: samsung: Allow pin value to be initialized using pinfunc
pinctrl: samsung: Allow grouping multiple pinmux/pinconf nodes
pinctrl: exynos: Consolidate irq_chips of GPIO and WKUP EINTs
pinctrl: samsung: Handle GPIO request and free using pinctrl helpers
pinctrl: samsung: Decouple direction setting from pinctrl
...
Merging in the few fixes we had also received, no need to keep those in
a separate branch.
* next/fixes-non-critical:
drivers: CCI: Correct use of ! and &
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
ARM: omap2+: gpmc-nand: Use dynamic platform_device_alloc()
omap16xx: Removes fixme no longer needed in ocpi_enable()
ARM: dts: OMAP5: Add device nodes for ABB
ARM: omap2+: usb-tusb6010.c: Cleaning up variable is set more than once
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
A quiet release, more bug fixes than anything else. A few things do
stand out though:
- Updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- Support for Rockchip SPI controllers (their first mainline
submission).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=u37g
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A quiet release, more bug fixes than anything else. A few things do
stand out though:
- updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- support for Rockchip SPI controllers (their first mainline
submission)"
* tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits)
spi: davinci: use spi_device.cs_gpio to store gpio cs per spi device
spi: davinci: add support to configure gpio cs through dt
spi/pl022: Explicitly truncate large bitmask
spi/atmel: Fix pointer to int conversion warnings on 64 bit builds
spi: davinci: fix to support more than 2 chip selects
spi: topcliff-pch: don't hardcode PCI slot to get DMA device
spi: orion: fix incorrect handling of cell-index DT property
spi: orion: Fix error return code in orion_spi_probe()
spi/rockchip: fix error return code in rockchip_spi_probe()
spi/rockchip: remove redundant dev_err call in rockchip_spi_probe()
spi/rockchip: remove duplicated include from spi-rockchip.c
ARM: dts: fix the chip select gpios definition in the SPI nodes
spi: s3c64xx: Update binding documentation
spi: s3c64xx: use the generic SPI "cs-gpios" property
spi: s3c64xx: Revert "spi: s3c64xx: Added provision for dedicated cs pin"
spi: atmel: Use dmaengine_prep_slave_sg() API
spi: topcliff-pch: Update error messages for dmaengine_prep_slave_sg() API
spi: sh-msiof: Use correct device for DMA mapping with IOMMU
spi: sh-msiof: Handle dmaengine_prep_slave_single() failures gracefully
spi: rspi: Handle dmaengine_prep_slave_sg() failures gracefully
...
Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2ZIACgkQMUfUDdst+ylvQwCfQKPKcwhtq4vJ2imUzJROEZwN
ygYAnRpFpH/19X59uGSdE7DAdhbitqKg
=uPh1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while"
* tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits)
USB: devio: fix issue with log flooding
uas: Log a warning when we cannot use uas because the hcd lacks streams
uas: Only complain about missing sg if all other checks succeed
xhci: Add missing checks for xhci_alloc_command failure
xhci: Rename Asrock P67 pci product-id to EJ168
xhci: Blacklist using streams on the Etron EJ168 controller
uas: Limit qdepth to 32 when connected over usb-2
uwb/whci: use correct structure type name in sizeof
usb-core bInterval quirk
USB: serial: ftdi_sio: Add support for new Xsens devices
USB: serial: ftdi_sio: Annotate the current Xsens PID assignments
usb: chipidea: debug: fix sparse non static symbol warnings
usb: ci_hdrc_imx doc: fsl,usbphy is required
usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY
usb: core: allow zero packet flag for interrupt urbs
usb: lvstest: Fix sparse warnings generated by kbuild test bot
USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down
phy: miphy365x: Represent each PHY channel as a DT subnode
phy: miphy365x: Provide support for the MiPHY356x Generic PHY
phy: miphy365x: Add Device Tree bindings for the MiPHY365x
...
Here's the big tty / serial driver update for 3.17-rc1.
Nothing major, just a number of fixes and new features for different
serial drivers, and some more tty core fixes and documentation of the
tty locks.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2C4ACgkQMUfUDdst+yllVgCgtZl/Mcr/LlxPgjsg2C1AE7nX
YJ4An3o4N112bkdGqhZ7RjAE6K/8YILx
=rPhE
-----END PGP SIGNATURE-----
Merge tag 'tty-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver update from Greg KH:
"Here's the big tty / serial driver update for 3.17-rc1.
Nothing major, just a number of fixes and new features for different
serial drivers, and some more tty core fixes and documentation of the
tty locks.
All of these have been in linux-next for a while"
* tag 'tty-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (82 commits)
tty/n_gsm.c: fix a memory leak in gsmld_open
pch_uart: don't hardcode PCI slot to get DMA device
tty: n_gsm, use setup_timer
Revert "ARC: [arcfpga] stdout-path now suffices for earlycon/console"
serial: sc16is7xx: Correct initialization of s->clk
serial: 8250_dw: Add support for deferred probing
serial: 8250_dw: Add optional reset control support
serial: st-asc: Fix overflow in baudrate calculation
serial: st-asc: Don't call BUG in asc_console_setup()
tty: serial: msm: Make of_device_id array const
tty/n_gsm.c: get gsm->num after gsm_activate_mux
serial/core: Fix too big allocation for attribute member
drivers/tty/serial: use correct type for dma_map/unmap
serial: altera_jtaguart: Fix putchar function passed to uart_console_write()
serial/uart/8250: Add tunable RX interrupt trigger I/F of FIFO buffers
Serial: allow port drivers to have a default attribute group
tty: kgdb_nmi: Automatically manage tty enable
serial: altera_jtaguart: Adpot uart_console_write()
serial: samsung: improve code clarity by defining a variable
serial: samsung: correct the case and default order in switch
...
Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no one
was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1wYACgkQMUfUDdst+ykrNwCgswPkRSAPQ3C8WvLhzUYRZZ/L
AqEAoJP0Q8Fz8unXjlSMcx7pgcqUaJ8G
=mrTQ
-----END PGP SIGNATURE-----
Merge tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no
one was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while"
* tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (2199 commits)
staging: comedi: addi_apci_1564: remove diagnostic interrupt support code
staging: comedi: addi_apci_1564: add subdevice to check diagnostic status
staging: wlan-ng: coding style problem fix
staging: wlan-ng: fixing coding style problems
staging: comedi: ii_pci20kc: request and ioremap memory
staging: lustre: bitwise vs logical typo
staging: dgnc: Remove unneeded dgnc_trace.c and dgnc_trace.h
staging: dgnc: rephrase comment
staging: comedi: ni_tio: remove some dead code
staging: rtl8723au: Fix static symbol sparse warning
staging: rtl8723au: usb_dvobj_init(): Remove unused variable 'pdev_desc'
staging: rtl8723au: Do not duplicate kernel provided USB macros
staging: rtl8723au: Remove never set struct pwrctrl_priv.bHWPowerdown
staging: rtl8723au: Remove two never set variables
staging: rtl8723au: RSSI_test is never set
staging:r8190: coding style: Fixed checkpatch reported Error
staging:r8180: coding style: Fixed too long lines
staging:r8180: coding style: Fixed commenting style
staging: lustre: ptlrpc: lproc_ptlrpc.c - fix dereferenceing user space buffer
staging: lustre: ldlm: ldlm_resource.c - fix dereferenceing user space buffer
...
drivers and fixes/enhancements to existing clock drivers. There are also
some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
* improvements to printks on errors
* flattening the previously hierarchal structure of per-clock entries
in debugfs
* allow per-clock debugfs entries that are specific to a particular
clock driver
* configure initial clock parent and/or initial clock rate from Device
Tree
* several feature enhancements to the composite clock type
* misc fixes
New clock drivers added include:
* TI Palmas PMIC
* Allwinner A23 SoC
* Qualcomm APQ8084 and IPQ8064 SoCs
* Rockchip rk3188, rk3066 and rk3288 SoCs
* STMicroelectronics STiH407 SoC
* Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK down"
power saving feature for their Exynos4 & Exynos5 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT38lmAAoJEDqPOy9afJhJh9YQAKROq+lrKaf+YAk22E0GCF30
Q+KZ9EcePdxWvcDPKsMIf/wAIYdtGDoI6wgyw1tcSWeLKwwyHMfVdOCExWig2gwl
/4LU2tACKe+Xa0HJnsbNwQGj2n4qMGOUsDeRRmK4rcbuHZhTP15IscmFCbL+sUia
z3uaYf7ty3a1tSXBl3NY4EpYAXGiE+MMVBoU08ATYOOjvGcxNNfu50JSltGXarqv
BFBjpv0oikN3RvbVyuUUvEF8m6AeNYhbqxI0IuNmoE+mAkgB2n221CK4Qv6a3oDb
QJebzRdeprcak8HrK76Ik6Dd9itcs03u6G1qwLc30JH5wUHYcgqA5bvqDIx+2W0J
Z7NPi3tFTry1aeXnZPk7DbWruzXLQkXkgRM4xHXsmezRnO7zDvuoDgUT0pIrS9+v
+BRIyfPiBL9Lp1J17R0I1K76O7YnvyQhX+0CdZx0SOJNGPl+SIwTI4q+gQoDIZqP
0ubpuaH4v6gZiEol2HXKYN9ASWyRtX7PfiexQgmts1aewlPopWfuc7LdxhHQIv3B
3O/7jbhdhXsf7VaTvx7xkFEMxjY7IwEF4pN0F+ulwWj/rLK3vLCnTwxgv8IrNHit
Dkzt4kVzLW/GSWa3irTnISvsg+bHkRc7aPuW/i0km7RYUuL2dcaJLEBPYuka/AdH
1xIMaGNpkA3HrS+8CQYf
=48y9
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.17 are mostly additions of new clock
drivers and fixes/enhancements to existing clock drivers. There are
also some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
- improvements to printks on errors
- flattening the previously hierarchal structure of per-clock entries
in debugfs
- allow per-clock debugfs entries that are specific to a particular
clock driver
- configure initial clock parent and/or initial clock rate from
Device Tree
- several feature enhancements to the composite clock type
- misc fixes
New clock drivers added include:
- TI Palmas PMIC
- Allwinner A23 SoC
- Qualcomm APQ8084 and IPQ8064 SoCs
- Rockchip rk3188, rk3066 and rk3288 SoCs
- STMicroelectronics STiH407 SoC
- Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK
down" power saving feature for their Exynos4 & Exynos5 SoCs"
* tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: Add missing of_clk_set_defaults export
clk: checking wrong variable in __set_clk_parents()
clk: Propagate any error return from debug_init()
clk: clps711x: Add DT bindings documentation
clk: Add CLPS711X clk driver
clk: st: Use round to closest divider flag
clk: st: Update frequency tables for fs660c32 and fs432c65
clk: st: STiH407: Support for clockgenA9
clk: st: STiH407: Support for clockgenD0/D2/D3
clk: st: STiH407: Support for clockgenC0
clk: st: Add quadfs reset handling
clk: st: Add polarity bit indication
clk: st: STiH407: Support for clockgenA0
clk: st: STiH407: Support for A9 MUX Clocks
clk: st: STiH407: Support for Flexgen Clocks
clk: st: Adds Flexgen clock binding
clk: st: Remove uncessary (void *) cast
clk: st: use static const for clkgen_pll_data tables
clk: st: use static const for stm_fs tables
clk: st: Update ST clock binding documentation
...
This patch adds common part of dsi node.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds sysreg property to fimd device node
which is required to use I80 interface.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds sysreg property to fimd device node
which is required to use I80 interface.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds socfpga Ethernet filter attributes for multicast
and unicast filters per Synopsys Ethernet IP configuration chosen
by Altera for the Cyclone 5 and Arria SOC FPGAs.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO pin connected to card detect was inverted twice: once by
the argument to the GPIO line itself where it was magically marked
as active low by the flag GPIO_ACTIVE_LOW (0x01) in the third cell,
and also marked active low AGAIN by explicitly stating
"cd-inverted" (a deprecated method).
After commit 78f87df2b4
"mmc: mmci: Use the common mmc DT parser" this results in the
line being inverted twice so it was effectively uninverted, while
the old code would not have this effect, instead disregarding the
flag on the GPIO line altogether, which is a bug. I admit the
semantics may be unclear but inverting twice is as good a
definition as any on how this should work.
So fix up the buggy device tree. Use proper #includes so the DTS
is clear and readable.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5XAH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap n900 regression fix for v3.16 rc series" from Tony Lindgren:
Minimal regression fix for n900 display that got broken with
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
* tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert enabling of twl configuration for n900
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 9188883fd6 (ARM: dts: Enable twl4030 off-idle configuration
for selected omaps) allowed n900 to cut off core voltages during
off-idle. This however caused a regression where twl regulator
vaux1 was not getting enabled for the LCD panel as we are not
requesting it for the panel.
Turns out quite a few devices on n900 are using vaux1, and we need
to either stop idling it, or add proper regulator_get calls for all
users. But until we have a proper solution implemented and tested,
let's just disable the twl off-idle configuration for now for n900.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 9188883fd6 (ARM: dts: Enable twl4030 off-idle configuration for selected omaps)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the address of L2 controler register in hi3620 SoC.
This has been wrong from the point that the file was merged
in v3.14.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
rc series. Mostly a fix for GPMC allocation and omap5 ABB
(Adaptive Body Bias).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nbzr
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.17/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge non-urgent omap fixes from Tony Lindgren:
Fixes for omaps that were not considered urgent enough for the
rc series. Mostly a fix for GPMC allocation and omap5 ABB
(Adaptive Body Bias).
* tag 'omap-for-v3.17/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2+: gpmc-nand: Use dynamic platform_device_alloc()
omap16xx: Removes fixme no longer needed in ocpi_enable()
ARM: dts: OMAP5: Add device nodes for ABB
ARM: omap2+: usb-tusb6010.c: Cleaning up variable is set more than once
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch extends nodes of PMU system controller on Exynos4210, 4x12,
5250 and 5420 SoCs with newly defined properties used by Exynos CLKOUT
driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
this new compatibility string prevents macb/gem driver from using the
scatter-gather and gso features on sama5d3x boards.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New functionality
* A new modifier to indicate that a rotation is relative to either
true or magnetic north. This is to be used by some magnetometers
that provide data in this way.
* hid magnetometer now supports output rotations from various variants on
North
* HMC5843 driver converted to regmap and reworked to allow easy support
of other similar devices. Support for HMC5983 added via both i2c and SPI.
* Rework of Exynos driver to simplify extension to support more devices.
* Addition of support for the Exynos3250 ADC (which requires an additional
clock) Support for quite a few more devices on its way.
Cleanups
* ad7997 - a number of cleanups and tweaks to how the events are controlled
to make it more intuitive.
* kxcjk - cleanups and minor fixes for this new driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=iOto
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.17d' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Fourth round of IIO new drivers, functionality and cleanups for the 3.17 cycle
New functionality
* A new modifier to indicate that a rotation is relative to either
true or magnetic north. This is to be used by some magnetometers
that provide data in this way.
* hid magnetometer now supports output rotations from various variants on
North
* HMC5843 driver converted to regmap and reworked to allow easy support
of other similar devices. Support for HMC5983 added via both i2c and SPI.
* Rework of Exynos driver to simplify extension to support more devices.
* Addition of support for the Exynos3250 ADC (which requires an additional
clock) Support for quite a few more devices on its way.
Cleanups
* ad7997 - a number of cleanups and tweaks to how the events are controlled
to make it more intuitive.
* kxcjk - cleanups and minor fixes for this new driver.
* Fix SD2CKCR register address of r8a7791 (R-Car M2) SoC
This corrects a bug introduced in v3.14 by
59e79895b9 ("ARM: shmobile: r8a7791: Add clocks").
However, it does not manifest in mainline code until
SDHI devices were enabled on the Koelsch board in v3.15 by
2c60a7df72 ("ARM: shmobile: Add SDHI devices for Koelsch DTS").
It also manifests on the Henninger board when
SDHI devices were enabled in v3.16-rc1 by
1299df03d7 ("ARM: shmobile: henninger: add SDHI0/2 DT support")
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT0FapAAoJENfPZGlqN0++socQAI25b++UQ89EiUQE/98yB/vq
ma63gl346dXdv6lb8iN+rx9Vk3wtzNuroozds2iulmAnutMTdQ83huektaYdPkQ4
T+RxOl4liJUbQRBg2+8UBtiaTB+oGQWbRkqt/MOvniTbOqYKs71Oym901ULlQMKL
9RSyWORUx5x2c+zZMJ0eU8T6Bl9hf0P0ikHwUv9ZYIQzrYxjJubdmyVoNI6slxF9
S4O4sUZfOSVqfSis5rEfWgG29jBYjlGdTyFXp1+kE19J02wikGRTjgM9bWkxarrF
wfa+ZQXjMywsdY8rCSxeNEYFuS3NW7s4ylRIC4UfpvSg1cvNVVE5m4BK0E2IOIyJ
kW/zSimYfh/RJSX+HMZ2hfipvFDE6dDOL5PHpwJ8fhWfM5Yinn1Wgfa2mUDxsPFe
CAfhtiTB56Rhzo+ln9UcNwaakZs/uSsG0jq3lI2zNTUd+1VMS+7xB/3pdKQjDGo/
75+UKvdcqJ4yprfcvKwIp0LsJCKWIm1hQTqSFWuYfpVaNbM+9CFQculw0YZxOWxc
xFr3LznFidUJCHKiM4ngnPBsLfDCdjVU5MyqDXcW9iVEKeSQJJ01CCORA4MjTUT5
niZEMcAoIMaeXeuVnL5FlRK5Owd6SgryWpy4XUlf+ioGLLE5EzuLqA9TJe4eo41P
caa5gpyUDbTjH1J4GktY
=SQyi
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes2-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Second Round of Renesas ARM Based SoC Fixes for v3.16" from Simon Horman
* Fix SD2CKCR register address of r8a7791 (R-Car M2) SoC
This corrects a bug introduced in v3.14 by
59e79895b9 ("ARM: shmobile: r8a7791: Add clocks").
However, it does not manifest in mainline code until
SDHI devices were enabled on the Koelsch board in v3.15 by
2c60a7df72 ("ARM: shmobile: Add SDHI devices for Koelsch DTS").
It also manifests on the Henninger board when
SDHI devices were enabled in v3.16-rc1 by
1299df03d7 ("ARM: shmobile: henninger: add SDHI0/2 DT support")
* tag 'renesas-fixes2-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: Fix SD2CKCR register address
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patchset fix wrong compatible string for Exynos3250 ADC. Exynos3250 SoC
need to control only special clock for ADC. Exynos SoC except for Exynos3250
has not included special clock for ADC. The exynos ADC driver can control
special clock if compatible string is 'exynos3250-adc-v2'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
: Most of them are for exynos SoCs, remove useless
codes and update for PMU consolidation.
- remove unnecessary header file in mach-exynos/pmu.c
- remove unused code in mach-exynos/common.h
- remove mach-exynos/regs-pmu.h dependency from PD
- remove file path from comment section in mach-exynos
- move SYSREG definitions into mach-exynos/regs-sys.h
- add mapping PMU base address via DT for PMU cleanup
- use staic in mach-exynos/common.h
- update Samsung UART config options for low-level debug
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=goDG
-----END PGP SIGNATURE-----
Merge tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
Merge "Samsung cleanup for v3.17" from Kukjin Kim:
Most of them are for exynos SoCs, remove useless codes and update for
PMU consolidation.
- remove unnecessary header file in mach-exynos/pmu.c
- remove unused code in mach-exynos/common.h
- remove mach-exynos/regs-pmu.h dependency from PD
- remove file path from comment section in mach-exynos
- move SYSREG definitions into mach-exynos/regs-sys.h
- add mapping PMU base address via DT for PMU cleanup
- use staic in mach-exynos/common.h
- update Samsung UART config options for low-level debug
* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add support for mapping PMU base address via DT
ARM: EXYNOS: Remove "linux/bug.h" from pmu.c
ARM: EXYNOS: Remove regs-pmu.h header dependency from pm_domain
ARM: EXYNOS: Remove file path from comment section
ARM: EXYNOS: Move SYSREG definition into sys-reg specific file
ARM: EXYNOS: Make exynos machine_ops as static
ARM: EXYNOS: Remove unused code in common.h
ARM: debug: Update Samsung UART config options
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch moves code related to the Tegra fuses out of arch/arm and
into a centralized location which could be shared with ARM64. It also
adds support for reading the fuse data through sysfs.
Included is also some preparatory work that moves Tegra-related header
files from include/linux to include/soc/tegra as suggested by Arnd.
Furthermore the Tegra chip ID is now retrieved using a function rather
than a variable so that sanity checks can be done. This is convenient
in subsequent patches that will move some of the code that's currently
called from Tegra machine setup into regular initcalls so that it can
be reused on 64-bit ARM. The sanity checks help with verifying that no
code tries to obtain the Tegra chip ID before the underlying driver is
properly initialized.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=XyRE
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.17-fuse-move' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
Merge "ARM: tegra: move fuse code out of arch/arm" from Thierry Reding:
This branch moves code related to the Tegra fuses out of arch/arm and
into a centralized location which could be shared with ARM64. It also
adds support for reading the fuse data through sysfs.
Included is also some preparatory work that moves Tegra-related header
files from include/linux to include/soc/tegra as suggested by Arnd.
Furthermore the Tegra chip ID is now retrieved using a function rather
than a variable so that sanity checks can be done. This is convenient
in subsequent patches that will move some of the code that's currently
called from Tegra machine setup into regular initcalls so that it can
be reused on 64-bit ARM. The sanity checks help with verifying that no
code tries to obtain the Tegra chip ID before the underlying driver is
properly initialized.
* tag 'tegra-for-3.17-fuse-move' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
Signed-off-by: Olof Johansson <olof@lixom.net>
The pwm driver requires a clocks property referencing the pwm peripheral
clk.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Correct the typo error for the second "uhphs_clk".
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch replaces the "cs-gpio" from "controller-data" node
as was specified in the old binding and uses the standard
"cs-gpios" property expected by the SPI core as is defined now
in the spi-s3c64xx driver DT binding.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add efuse and apbmisc bindings for Tegra20, Tegra30, Tegra114 and
Tegra124.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
some constification from static code analysis.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmbF
-----END PGP SIGNATURE-----
Merge tag 'ux500-core-for-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
Merge "Ux500 core changes for v3.17 take 1" from Linus Walleij:
Some minor cleanups to the Ux500 core. DT-only probe path and
some constification from static code analysis.
* tag 'ux500-core-for-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: remove pointless cache setup complexity
ARM: ux500: storage class should be before const qualifier
ARM: ux500: Staticize ab8505_regulators
ARM: ux500: Staticize local symbols in cpu-db8500.c
ARM: ux500: Staticise ux500_soc_attr
+ Linux 3.16-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
- update the parent for Auudss clock because kernel will be hang
during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
on/off, its regarding clock source will be reset and it causes
a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
system failure will be happened on other exynos SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=didu
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes-3 for 3.16" from Kukjin Kim:
Samsung fixes-3 for v3.16
- update the parent for Auudss clock because kernel will be hang
during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
on/off, its regarding clock source will be reset and it causes
a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
system failure will be happened on other exynos SoCs.
* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
ARM: dts: Add clock property for mfc_pd in exynos5420
clk: exynos5420: Add IDs for clocks used in PD mfc
ARM: EXYNOS: Add support for clock handling in power domain
ARM: dts: Update the parent for Audss clocks in Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
Add clocks for usb device, or else switch to CCF, the gadget
won't work.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pads for PB0-PB3, PC0-PC4, PE26-PE31 and PF24-PF31 does not exist on
the i.MX27 SOC. There is no reason to define them, the presence of
such definitions in the DTS files is a bug.
This patch removes these nonexistent pad definitions.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding the optional clock property for the mfc_pd for
handling the re-parenting while pd on/off.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
restart handling and phy regulators and SATA interconnect data.
Also few build fixes related to the DSP driver in staging, and trivial
stuff like removal of broken and soon to be unused platform data init
for HDMI audio that would be good to get into the -rc series if not
too late.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=paeu
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.16-rc4" from Tony Lindgren:
Fixes for omaps for the -rc series. It's mostly fixes for clock rates,
restart handling and phy regulators and SATA interconnect data.
Also few build fixes related to the DSP driver in staging, and trivial
stuff like removal of broken and soon to be unused platform data init
for HDMI audio that would be good to get into the -rc series if not
too late.
* tag 'omap-for-v3.16/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove non working OMAP HDMI audio initialization
ARM: dts: Fix TI CPSW Phy mode selection on IGEP COM AQUILA.
ARM: dts: am335x-evmsk: Enable the McASP FIFO for audio
ARM: dts: am335x-evm: Enable the McASP FIFO for audio
ARM: OMAP2+: Make GPMC skip disabled devices
ARM: OMAP2+: create dsp device only on OMAP3 SoCs
ARM: dts: dra7-evm: Make VDDA_1V8_PHY supply always on
ARM: DRA7/AM43XX: fix header definition for omap44xx_restart
ARM: OMAP2+: clock/dpll: fix _dpll_test_fint arithmetics overflow
ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss
ARM: DRA7: hwmod: Fixup SATA hwmod
ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver
ARM: dts: dra7xx-clocks: Fix the l3 and l4 clock rates
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds alias entries for UART nodes of all SoCs using
samsung-uart compatible UART controllers, so that the dependency on
probe order is removed and deterministic device naming is assured.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new properties to all of the Tegra PHYs that are now required
according to the binding.
In order to stay compatible with old device trees, the USB drivers
will still function without these reset properties but with the old,
potentially buggy behaviour.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ABB device nodes for OMAP5 family of devices. Data is based on
final production OMAP543x Technical Reference Manual revision Z (April 2013).
Final production Data Manual for OMAP5432 SWPS050F(APRIL 2014).
[nm@ti.com: co-developer and updates to latest documentation]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Remove <mach/memory.h> from the Integrator, paving the
road for multiplatform.
- Push the CLCD helper code down into the framebuffer subsystem,
removing the last hook in plat-versatile for the Integrator,
also paving the road for multiplatform.
Patches tested on Integrator/AP, Integrator/CP and Versatile AB
(all real hardware).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Tuj
-----END PGP SIGNATURE-----
Merge tag 'versatile-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/cleanup
Merge "First pull request of Versatile family clean-ups for v3.17" from Linus
Walleij:
- Remove <mach/memory.h> from the Integrator, paving the
road for multiplatform.
- Push the CLCD helper code down into the framebuffer subsystem,
removing the last hook in plat-versatile for the Integrator,
also paving the road for multiplatform.
Patches tested on Integrator/AP, Integrator/CP and Versatile AB
(all real hardware).
* tag 'versatile-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
video: move Versatile CLCD helpers
ARM: integrator: get rid of <mach/memory.h>
Signed-off-by: Olof Johansson <olof@lixom.net>
