Don found that P4 PMU reads CCCR register instead of counter
itself (in attempt to catch unflagged event) this makes P4
NMI handler to consume all NMIs it observes. So the other
NMI users such as kgdb simply have no chance to get NMI
on their hands.
Side note: at moment there is no way to run nmi-watchdog
together with perf tool. This is because both 'perf top' and
nmi-watchdog use same event. So while nmi-watchdog reserves
one event/counter for own needs there is no room for perf tool
left (there is a way to disable nmi-watchdog on boot of course).
Ming has tested this patch with the following results
| 1. watchdog disabled
|
| kgdb tests on boot OK
| perf works OK
|
| 2. watchdog enabled, without patch perf-x86-p4-nmi-4
|
| kgdb tests on boot hang
|
| 3. watchdog enabled, without patch perf-x86-p4-nmi-4 and do not run kgdb
| tests on boot
|
| "perf top" partialy works
| cpu-cycles no
| instructions yes
| cache-references no
| cache-misses no
| branch-instructions no
| branch-misses yes
| bus-cycles no
|
| 4. watchdog enabled, with patch perf-x86-p4-nmi-4 applied
|
| kgdb tests on boot OK
| perf does not work, NMI "Dazed and confused" messages show up
|
Which means we still have problems with p4 box due to 'unknown'
nmi happens but at least it should fix kgdb test cases.
Reported-by: Jason Wessel <jason.wessel@windriver.com>
Reported-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Don Zickus <dzickus@redhat.com>
Acked-by: Lin Ming <ming.m.lin@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <4D275E7E.3040903@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
From the x86_64 low level interrupt handlers, the frame pointer is
saved right after the partial pt_regs frame.
rbp is not supposed to be part of the irq partial saved registers,
but it only requires to extend the pt_regs frame by 8 bytes to
do so, plus a tiny stack offset fixup on irq exit.
This changes a bit the semantics or get_irq_entry() that is supposed
to provide only the value of caller saved registers and the cpu
saved frame. However it's a win for unwinders that can walk through
stack frames on top of get_irq_regs() snapshots.
A noticeable impact is that it makes perf events cpu-clock and
task-clock events based callchains working on x86_64.
Let's then save rbp into the irq pt_regs.
As a result with:
perf record -e cpu-clock perf bench sched messaging
perf report --stdio
Before:
20.94% perf [kernel.kallsyms] [k] lock_acquire
|
--- lock_acquire
|
|--44.01%-- __write_nocancel
|
|--43.18%-- __read
|
|--6.08%-- fork
| create_worker
|
|--0.88%-- _dl_fixup
|
|--0.65%-- do_lookup_x
|
|--0.53%-- __GI___libc_read
--4.67%-- [...]
After:
19.23% perf [kernel.kallsyms] [k] __lock_acquire
|
--- __lock_acquire
|
|--97.74%-- lock_acquire
| |
| |--21.82%-- _raw_spin_lock
| | |
| | |--37.26%-- unix_stream_recvmsg
| | | sock_aio_read
| | | do_sync_read
| | | vfs_read
| | | sys_read
| | | system_call
| | | __read
| | |
| | |--24.09%-- unix_stream_sendmsg
| | | sock_aio_write
| | | do_sync_write
| | | vfs_write
| | | sys_write
| | | system_call
| | | __write_nocancel
v2: Fix cfi annotations.
Reported-by: Soeren Sandmann Pedersen <sandmann@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Jan Beulich <JBeulich@novell.com>
In dump_stack function, bp isn't used anymore, which is introduced by
commit 9c0729dc80. This patch removes bp
completely.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Cc: Soeren Sandmann <sandmann@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <AANLkTik9U_Z0WSZ7YjrykER_pBUfPDdgUUmtYx=R74nL@mail.gmail.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Just re-arrange the code a bit to make it easier to follow what is
going on. Basically un-negating the if-statement and swapping the code
inside the if-statement with code outside.
No functional changes.
Originally-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-7-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In original NMI handler, NMI reason io port (0x61) is only processed
on BSP. This makes it impossible to hot-remove BSP. To solve the
issue, a raw spinlock is used to allow the port to be processed on any
CPU.
Originally-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-6-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With priorities in place and no one really understanding the difference between
DIE_NMI and DIE_NMI_IPI, just remove DIE_NMI_IPI and convert everyone to DIE_NMI.
This also simplifies default_do_nmi() a little bit. Instead of calling the
die_notifier in both the if and else part, just pull it out and call it before
the if-statement. This has the side benefit of avoiding a call to the ioport
to see if there is an external NMI sitting around until after the (more frequent)
internal NMIs are dealt with.
Patch-Inspired-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-5-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In order to consolidate the NMI die_chain events, we need to setup the priorities
for the die notifiers.
I started by defining a bunch of common priorities that can be used by the
notifier blocks. Then I modified the notifier blocks to use the newly created
priorities.
Now that the priorities are straightened out, it should be easier to remove the
event DIE_NMI_IPI.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-4-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
They are a handful of places in the code that register a die_notifier
as a catch all in case no claims the NMI. Unfortunately, they trigger
on events like DIE_NMI and DIE_NMI_IPI, which depending on when they
registered may collide with other handlers that have the ability to
determine if the NMI is theirs or not.
The function unknown_nmi_error() makes one last effort to walk the
die_chain when no one else has claimed the NMI before spitting out
messages that the NMI is unknown.
This is a better spot for these devices to execute any code without
colliding with the other handlers.
The two drivers modified are only compiled on x86 arches I believe, so
they shouldn't be affected by other arches that may not have
DIE_NMIUNKNOWN defined.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: openipmi-developer@lists.sourceforge.net
Cc: dann frazier <dannf@hp.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Replace the NMI related magic numbers with symbol constants.
Memory parity error is only valid for IBM PC-AT, newer machine use
bit 7 (0x80) of 0x61 port for PCI SERR. While memory error is usually
reported via MCE. So corresponding function name and kernel log string
is changed.
But on some machines, PCI SERR line is still used to report memory
errors. This is used by EDAC, so corresponding EDAC call is reserved.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-alternatives-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, suspend: Avoid unnecessary smp alternatives switch during suspend/resume
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-64, asm: Use fxsaveq/fxrestorq in more places
* 'x86-hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hwmon: Add core threshold notification to therm_throt.c
* 'x86-paravirt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, paravirt: Use native_halt on a halt, not native_safe_halt
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
locking, lockdep: Convert sprintf_symbol to %pS
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq: Better struct irqaction layout
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV, BAU: Extend for more than 16 cpus per socket
x86, UV: Fix the effect of extra bits in the hub nodeid register
x86, UV: Add common uv_early_read_mmr() function for reading MMRs
* 'x86-tsc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Check tsc available/disabled in the delayed init function
x86: Improve TSC calibration using a delayed workqueue
x86: Make tsc=reliable override boot time stability checks
* 'x86-security-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
module: Move RO/NX module protection to after ftrace module update
x86: Resume trampoline must be executable
x86: Add RO/NX protection for loadable kernel modules
x86: Add NX protection for kernel data
x86: Fix improper large page preservation
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, earlyprintk: Move mrst early console to platform/ and fix a typo
x86, apbt: Setup affinity for apb timers acting as per-cpu timer
ce4100: Add errata fixes for UART on CE4100
x86: platform: Move iris to x86/platform where it belongs
x86, mrst: Check platform_device_register() return code
x86/platform: Add Eurobraille/Iris power off support
x86, mrst: Add explanation for using 1960 as the year offset for vrtc
x86, mrst: Fix dependencies of "select INTEL_SCU_IPC"
x86, mrst: The shutdown for MRST requires the SCU IPC mechanism
x86: Ce4100: Add reboot_fixup() for CE4100
ce4100: Add PCI register emulation for CE4100
x86: Add CE4100 platform support
x86: mrst: Set vRTC's IRQ to level trigger type
x86: mrst: Add audio driver bindings
rtc: Add drivers/rtc/rtc-mrst.c
x86: mrst: Add vrtc driver which serves as a wall clock device
x86: mrst: Add Moorestown specific reboot/shutdown support
x86: mrst: Parse SFI timer table for all timer configs
x86/mrst: Add SFI platform device parsing code
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, microcode, AMD: Cleanup code a bit
x86, microcode, AMD: Replace vmalloc+memset with vzalloc
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix included-by file reference comments
x86, cpu: Only CPU features determine NX capabilities
x86, cpu: Call verify_cpu during 32bit CPU startup
x86, cpu: Clear XD_DISABLED flag on Intel to regain NX
x86, cpu: Rename verify_cpu_64.S to verify_cpu.S
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix APIC ID sizing bug on larger systems, clean up MAX_APICS confusion
x86, acpi: Parse all SRAT cpu entries even above the cpu number limitation
x86, acpi: Add MAX_LOCAL_APIC for 32bit
x86: io_apic: Split setup_ioapic_ids_from_mpc()
x86: io_apic: Fix CONFIG_X86_IO_APIC=n breakage
x86: apic: Move probe_nr_irqs_gsi() into ioapic_init_mappings()
x86: Allow platforms to force enable apic
* 'x86-amd-nb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cacheinfo: Cleanup L3 cache index disable support
x86, amd-nb: Cleanup AMD northbridge caching code
x86, amd-nb: Complete the rename of AMD NB and related code
Prevent the long delay in io_check_error making NMI watchdog
timeout.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
LKML-Reference: <1294198689-15447-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The spin_lock_debug/rcu_cpu_stall detector uses
trigger_all_cpu_backtrace() to dump cpu backtrace.
Therefore it is possible that trigger_all_cpu_backtrace()
could be called at the same time on different CPUs, which
triggers and 'unknown reason NMI' warning. The following case
illustrates the problem:
CPU1 CPU2 ... CPU N
trigger_all_cpu_backtrace()
set "backtrace_mask" to cpu mask
|
generate NMI interrupts generate NMI interrupts ...
\ | /
\ | /
The "backtrace_mask" will be cleaned by the first NMI interrupt
at nmi_watchdog_tick(), then the following NMI interrupts
generated by other cpus's arch_trigger_all_cpu_backtrace() will
be taken as unknown reason NMI interrupts.
This patch uses a test_and_set to avoid the problem, and stop
the arch_trigger_all_cpu_backtrace() from calling to avoid
dumping a double cpu backtrace info when there is already a
trigger_all_cpu_backtrace() in progress.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Reviewed-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Cc: fweisbec@gmail.com
LKML-Reference: <1294198689-15447-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Don Zickus <dzickus@redhat.com>
There are some paths that walk the die_chain with preemption on.
Make sure we are in an NMI call before we start doing anything.
This was triggered by do_general_protection calling notify_die
with DIE_GPF.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Don Zickus <dzickus@redhat.com>
LKML-Reference: <1294198689-15447-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Found one x2apic pre-enabled system, x2apic_mode suddenly get
corrupted after register some cpus, when compiled
CONFIG_NR_CPUS=255 instead of 512.
It turns out that generic_processor_info() ==> phyid_set(apicid,
phys_cpu_present_map) causes the problem.
phys_cpu_present_map is sized by MAX_APICS bits, and pre-enabled
system some cpus have an apic id > 255.
The variable after phys_cpu_present_map may get corrupted
silently:
ffffffff828e8420 B phys_cpu_present_map
ffffffff828e8440 B apic_verbosity
ffffffff828e8444 B local_apic_timer_c2_ok
ffffffff828e8448 B disable_apic
ffffffff828e844c B x2apic_mode
ffffffff828e8450 B x2apic_disabled
ffffffff828e8454 B num_processors
...
Actually phys_cpu_present_map is referenced via apic id, instead
index. We should use MAX_LOCAL_APIC instead MAX_APICS.
For 64-bit it will be 32768 in all cases. BSS will increase by 4k bytes
on 64-bit:
text data bss dec filename
21696943 4193748 12787712 38678403 vmlinux.before
21696943 4193748 12791808 38682499 vmlinux.after
No change on 32bit.
Finally we can remove MAX_APCIS that was rather confusing.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4D23BD9C.3070102@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
v2.6.36-rc8-54-gb40827f (x86-32, mm: Add an initial page table
for core bootstrapping) made x86 boot using initial_page_table
and broke lguest.
For 2.6.37 we simply cut & paste the initialization code into
lguest (da32dac101 "lguest: populate initial_page_table"), now
we fix it properly by doing that initialization before the
paravirt jump.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: lguest <lguest@ozlabs.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <201101041720.54535.rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add these new power trace events:
power:cpu_idle
power:cpu_frequency
power:machine_suspend
The old C-state/idle accounting events:
power:power_start
power:power_end
Have now a replacement (but we are still keeping the old
tracepoints for compatibility):
power:cpu_idle
and
power:power_frequency
is replaced with:
power:cpu_frequency
power:machine_suspend is newly introduced.
Jean Pihet has a patch integrated into the generic layer
(kernel/power/suspend.c) which will make use of it.
the type= field got removed from both, it was never
used and the type is differed by the event type itself.
perf timechart userspace tool gets adjusted in a separate patch.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: rjw@sisk.pl
LKML-Reference: <1294073445-14812-3-git-send-email-trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <1290072314-31155-2-git-send-email-trenn@suse.de>
Fix a hard-coded limit of a maximum of 16 cpu's per socket.
The UV Broadcast Assist Unit code initializes by scanning the
cpu topology of the system and assigning a master cpu for each
socket and UV hub. That scan had an assumption of a limit of 16
cpus per socket. With Westmere we are going over that limit.
The UV hub hardware will allow up to 32.
If the scan finds the system has gone over that limit it returns
an error and we print a warning and fall back to doing TLB
shootdowns without the BAU.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org> # .37.x
LKML-Reference: <E1PZol7-0000mM-77@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds code to therm_throt.c to notify core thermal threshold
events. These thresholds are supported by the IA32_THERM_INTERRUPT register.
The status/log for the same is monitored using the IA32_THERM_STATUS register.
The necessary #defines are in msr-index.h. A call back is added to mce.h, to
further notify the thermal stack, about the threshold events.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
LKML-Reference: <D6D887BA8C9DFF48B5233887EF04654105C1251710@bgsmsx502.gar.corp.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Disable preemption in init_ibs(). The function only checks the
ibs capabilities and sets up pci devices (if necessary). It runs
only on one cpu but operates with the local APIC and some MSRs,
thus it is better to disable preemption.
[ 7.034377] BUG: using smp_processor_id() in preemptible [00000000] code: modprobe/483
[ 7.034385] caller is setup_APIC_eilvt+0x155/0x180
[ 7.034389] Pid: 483, comm: modprobe Not tainted 2.6.37-rc1-20101110+ #1
[ 7.034392] Call Trace:
[ 7.034400] [<ffffffff812a2b72>] debug_smp_processor_id+0xd2/0xf0
[ 7.034404] [<ffffffff8101e985>] setup_APIC_eilvt+0x155/0x180
[ ... ]
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=22812
Reported-by: <atswartz@gmail.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: oprofile-list@lists.sourceforge.net <oprofile-list@lists.sourceforge.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org> [2.6.37.x]
LKML-Reference: <20110103111514.GM4739@erda.amd.com>
[ small cleanups ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
isr_ack is never initialized. So, until the first PIC reset, interrupts
may fail to be injected. This can cause Windows XP to fail to boot, as
reported in the fallout from the fix to
https://bugzilla.kernel.org/show_bug.cgi?id=21962.
Reported-and-tested-by: Nicolas Prochazka <prochazka.nicolas@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We use the physical address instead of the base gfn for the four
PAE page directories we use in unpaged mode. When the guest accesses
an address above 1GB that is backed by a large host page, a BUG_ON()
in kvm_mmu_set_gfn() triggers.
Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=21962
Reported-and-tested-by: Nicolas Prochazka <prochazka.nicolas@gmail.com>
KVM-Stable-Tag.
Signed-off-by: Avi Kivity <avi@redhat.com>
halt() should use native_halt()
safe_halt() uses native_safe_halt()
If CONFIG_PARAVIRT=y, halt() is defined in arch/x86/include/asm/paravirt.h as
static inline void halt(void)
{
PVOP_VCALL0(pv_irq_ops.safe_halt);
}
Otherwise (no CONFIG_PARAVIRT) halt() in arch/x86/include/asm/irqflags.h is
static inline void halt(void)
{
native_halt();
}
So it looks to me like the CONFIG_PARAVIRT case of using native_safe_halt()
for a halt() is an oversight.
Am I missing something?
It probably hasn't shown up as a problem because the local apic is disabled
on a shutdown or restart. But if we disable interrupts and call halt()
we shouldn't expect that the halt() will re-enable interrupts.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1PSBcz-0001g1-FM@eag09.americas.sgi.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In arch/x86/kernel/microcode_intel.c::generic_load_microcode()
we have this:
while (leftover) {
...
if (get_ucode_data(mc, ucode_ptr, mc_size) ||
microcode_sanity_check(mc) < 0) {
vfree(mc);
break;
}
...
}
if (mc)
vfree(mc);
This will cause a double free of 'mc'. This patch fixes that by
just removing the vfree() call in the loop since 'mc' will be
freed nicely just after we break out of the loop.
There's also a second change in the patch. I noticed a lot of
checks for pointers being NULL before passing them to vfree().
That's completely redundant since vfree() deals gracefully with
being passed a NULL pointer. Removing the redundant checks
yields a nice size decrease for the object file.
Size before the patch:
text data bss dec hex filename
4578 240 1032 5850 16da arch/x86/kernel/microcode_intel.o
Size after the patch:
text data bss dec hex filename
4489 240 984 5713 1651 arch/x86/kernel/microcode_intel.o
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Shaohua Li <shaohua.li@intel.com>
LKML-Reference: <alpine.LNX.2.00.1012251946100.10759@swampdragon.chaosbits.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix to support libdwfl older than 0.148
perf tools: Fix lazy wildcard matching
perf buildid-list: Fix error return for success
perf buildid-cache: Fix symbolic link handling
perf symbols: Stop using vmlinux files with no symbols
perf probe: Fix use of kernel image path given by 'k' option
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, kexec: Limit the crashkernel address appropriately
Recent Intel new system have different order in MADT, aka will list all thread0
at first, then all thread1.
But SRAT table still old order, it will list cpus in one socket all together.
If the user have compiled limited NR_CPUS or boot with nr_cpus=, could have missed
to put some cpus apic id to node mapping into apicid_to_node[].
for example for 4 sockets system with 64 cpus with nr_cpus=32 will get crash...
[ 9.106288] Total of 32 processors activated (136190.88 BogoMIPS).
[ 9.235021] divide error: 0000 [#1] SMP
[ 9.235315] last sysfs file:
[ 9.235481] CPU 1
[ 9.235592] Modules linked in:
[ 9.245398]
[ 9.245478] Pid: 2, comm: kthreadd Not tainted 2.6.37-rc1-tip-yh-01782-ge92ef79-dirty #274 /Sun Fire x4800
[ 9.265415] RIP: 0010:[<ffffffff81075a8f>] [<ffffffff81075a8f>] select_task_rq_fair+0x4f0/0x623
...
[ 9.645938] RIP [<ffffffff81075a8f>] select_task_rq_fair+0x4f0/0x623
[ 9.665356] RSP <ffff88103f8d1c40>
[ 9.665568] ---[ end trace 2296156d35fdfc87 ]---
So let just parse all cpu entries in SRAT.
Also add apicid checking with MAX_LOCAL_APIC, in case We could out of boundaries of
apicid_to_node[].
it fixes following bug too.
https://bugzilla.kernel.org/show_bug.cgi?id=22662
-v2: expand to 32bit according to hpa
need to add MAX_LOCAL_APIC for 32bit
Reported-and-Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Tested-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D0AD486.9020704@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We should use MAX_LOCAL_APIC for max apic ids and MAX_APICS as number
of local apics.
Also apic_version[] array should use MAX_LOCAL_APICs.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D0AD464.2020408@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The x86 arch has shifted its use of the nmi_watchdog from a
local implementation to the global one provide by
kernel/watchdog.c. This shift has caused a whole bunch of
compile problems under different config options. I attempt to
simplify things with the patch below.
In order to simplify things, I had to come to terms with the
meaning of two terms ARCH_HAS_NMI_WATCHDOG and
CONFIG_HARDLOCKUP_DETECTOR. Basically they mean the same thing,
the former on a local level and the latter on a global level.
With the old x86 nmi watchdog gone, there is no need to rely on
defining the ARCH_HAS_NMI_WATCHDOG variable because it doesn't
make sense any more. x86 will now use the global
implementation.
The changes below do a few things. First it changes the few
places that relied on ARCH_HAS_NMI_WATCHDOG to use
CONFIG_X86_LOCAL_APIC (the former was an alias for the latter
anyway, so nothing unusual here). Those pieces of code were
relying more on local apic functionality the nmi watchdog
functionality, so the change should make sense.
Second, I removed the x86 implementation of
touch_nmi_watchdog(). It isn't need now, instead x86 will rely
on kernel/watchdog.c's implementation.
Third, I removed the #define ARCH_HAS_NMI_WATCHDOG itself from
x86. And tweaked the include/linux/nmi.h file to tell users to
look for an externally defined touch_nmi_watchdog in the case of
ARCH_HAS_NMI_WATCHDOG _or_ CONFIG_HARDLOCKUP_DETECTOR. This
changes removes some of the ugliness in that file.
Finally, I added a Kconfig dependency for
CONFIG_HARDLOCKUP_DETECTOR that said you can't have
ARCH_HAS_NMI_WATCHDOG _and_ CONFIG_HARDLOCKUP_DETECTOR. You can
only have one nmi_watchdog.
Tested with
ARCH=i386: allnoconfig, defconfig, allyesconfig, (various broken
configs) ARCH=x86_64: allnoconfig, defconfig, allyesconfig,
(various broken configs)
Hopefully, after this patch I won't get any more compile broken
emails. :-)
v3:
changed a couple of 'linux/nmi.h' -> 'asm/nmi.h' to pick-up correct function
prototypes when CONFIG_HARDLOCKUP_DETECTOR is not set.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: fweisbec@gmail.com
LKML-Reference: <1293044403-14117-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
UV systems can be partitioned into multiple independent SSIs.
Large partitioned systems may have extra bits in the node_id
register. These bits are used when the total memory on all SSIs
exceeds 16TB. These extra bits need to be ignored when
calculating x2apic_extra_bits.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20101130195926.972776133@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Early in boot, reading MMRs from the UV hub controller require
calls to early_ioremap()/early_iounmap(). Rather than
duplicating code, add a common function to do the
map/read/unmap.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20101130195926.834804371@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing
This patch adds support for up to 6 hardware counters for AMD family
15h cpus. There is a new MSR range for hardware counters beginning at
MSRC001_0200 Performance Event Select (PERF_CTL0).
Signed-off-by: Robert Richter <robert.richter@amd.com>
