Enables PPS support in atmel serial driver to make PPS API working.
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In 8250.c original ns16550 autoconfig code, we change the divisor latch when
we goto to high speed mode, we're assuming the previous speed is legacy. This
some times is not true.
For example in a system with both CONFIG_SERIAL_8250 and
CONFIG_SERIAL_8250_PNP set, in this case, the code (autoconfig) will be called
twice, one in serial8250_init/probe() and the other is from
serial_pnp_probe. When serial_pnp_probe calls the autoconfig for NS16550A,
it's already in high speed mode, change the divisor latch (quot << 3) in this
case will make the UART console garbled.
CC: Greg Kroah-Hartman <greg@kroah.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-kernel@vger.kernel.org
CC: stable@kernel.org
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For any reason if the NS16550A was not work in high speed mode (e.g. we hold
NS16550A from going to high speed mode in autoconfig_16550a()), now we are
resume from suspend, we should also set the uartclk to the correct
value. Otherwise it is still the old 1843200 and that will bring issues.
CC: Greg Kroah-Hartman <greg@kroah.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-kernel@vger.kernel.org
CC: stable@kernel.org
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renamed spi_driver variable to not be h/w specific
set driver name to use DRVNAME define
removed commented-out define
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The probe routine should call spi_setup() to configure
the SPI bus so it can properly communicate with the device.
E.g. the device operates in SPI mode 1.
Called spi_setup to configure SPI mode, max_speed_hz, and bpw
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Platforms containing the 6260 can run up to 25Mhz.
For these platforms set max_speed_hz to 25Mhz.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
driver should support 32bit SPI transfers. The boolean variable
only allowed 8/16.
Changed to support 8/16/32 for future enabling
of 32 bpw.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a SPI protocol driver and has no DMA ops
associated with the device so the call will fail. Furthermore,
the DMA allocation made here will be used by the SPI
controller driver (parent dev) so it makes sense to
pass that device instead.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The port ops must be set AFTER calling port init as that function
zeroes the structure
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
seems there's no longer need for using con_buf/conf_buf_mtx
as vcs_read/vcs_write buffer for user's data.
The do_con_write function, that was the other user of this,
is currently using its own kmalloc-ed buffer.
Not sure when this got changed, as I was able to find this code
in 2.6.9, but it's already gone as far as current git history
goes - 2.6.12-rc2.
AFAICS there's a behaviour change with the current change.
The lseek is not completely mutually exclusive with the
vcs_read/vcs_write - the file->f_pos might get updated
via lseek callback during the vcs_read/vcs_write processing.
I tried to find out if the prefered behaviour is to keep
this in sync within read/write/lseek functions, but I did
not find any pattern on different places.
I guess if user end up calling write/lseek from different
threads she should know what she's doing. If needed we
could use dedicated fd mutex/buffer.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
printk()s without a priority level default to KERN_WARNING. To reduce
noise at KERN_WARNING, this patch set the priority level appriopriately
for unleveled printks()s. This should be useful to folks that look at
dmesg warnings closely.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the existing bfin_jtag_comm TTY driver to the HVC layer so
that the common HVC code can worry about all of the TTY/polling crap and
leave the Blackfin code to worry about the Blackfin bits.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
virtual console: add keyboard mode OFF
Add a new mode for the virtual console keyboard OFF in which all input
other than shift keys is ignored. Prevents vt input buffers from
overflowing when a program opens but doesn't read from a tty, like X11
using evdev for input.
Signed-off-by: Arthur Taylor <art@ified.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The inline assembly differences for v6 vs. v7 in the hvc_dcc
driver are purely optimizations. On a v7 processor, an mrc with
the pc sets the condition codes to the 28-31 bits of the register
being read. It just so happens that the TX/RX full bits the DCC
driver is testing for are high enough in the register to be put
into the condition codes. On a v6 processor, this "feature" isn't
implemented and thus we have to do the usual read, mask, test
operations to check for TX/RX full.
Since we already test the RX/TX full bits before calling
__dcc_getchar() and __dcc_putchar() we don't actually need to do
anything special for v7 over v6. The only difference is in
hvc_dcc_get_chars(). We would test RX full, poll RX full, and
then read a character from the buffer, whereas now we will test
RX full, read a character from the buffer, and then test RX full
again for the second iteration of the loop. It doesn't seem
possible for the buffer to go from full to empty between testing
the RX full and reading a character. Therefore, replace the v7
versions with the v6 versions and everything works the same.
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Casting and anding with 0xff is unnecessary in
hvc_dcc_put_chars() since buf is already a char[].
__dcc_get_char() can't return an int less than 0 since it only
returns a char. Simplify the if statement in hvc_dcc_get_chars()
to take this into account.
Cc: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without marking the asm __dcc_getstatus() volatile my compiler
decides it can cache the value of __ret in a register and then
check the value of it continually in hvc_dcc_put_chars() (I had
to replace get_wait/put_wait with 1 and fixup the branch
otherwise my disassembler barfed on __dcc_(get|put)char).
00000000 <hvc_dcc_put_chars>:
0: ee103e11 mrc 14, 0, r3, cr0, cr1, {0}
4: e3a0c000 mov ip, #0 ; 0x0
8: e2033202 and r3, r3, #536870912 ; 0x20000000
c: ea000006 b 2c <hvc_dcc_put_chars+0x2c>
10: e3530000 cmp r3, #0 ; 0x0
14: 1afffffd bne 10 <hvc_dcc_put_chars+0x10>
18: e7d1000c ldrb r0, [r1, ip]
1c: ee10fe11 mrc 14, 0, pc, cr0, cr1, {0}
20: 2afffffd bcs 1c <hvc_dcc_put_chars+0x1c>
24: ee000e15 mcr 14, 0, r0, cr0, cr5, {0}
28: e28cc001 add ip, ip, #1 ; 0x1
2c: e15c0002 cmp ip, r2
30: bafffff6 blt 10 <hvc_dcc_put_chars+0x10>
34: e1a00002 mov r0, r2
38: e12fff1e bx lr
As you can see, the value of the mrc is checked against
DCC_STATUS_TX (bit 29) and then stored in r3 for later use.
Marking the asm volatile produces the following:
00000000 <hvc_dcc_put_chars>:
0: e3a03000 mov r3, #0 ; 0x0
4: ea000007 b 28 <hvc_dcc_put_chars+0x28>
8: ee100e11 mrc 14, 0, r0, cr0, cr1, {0}
c: e3100202 tst r0, #536870912 ; 0x20000000
10: 1afffffc bne 8 <hvc_dcc_put_chars+0x8>
14: e7d10003 ldrb r0, [r1, r3]
18: ee10fe11 mrc 14, 0, pc, cr0, cr1, {0}
1c: 2afffffd bcs 18 <hvc_dcc_put_chars+0x18>
20: ee000e15 mcr 14, 0, r0, cr0, cr5, {0}
24: e2833001 add r3, r3, #1 ; 0x1
28: e1530002 cmp r3, r2
2c: bafffff5 blt 8 <hvc_dcc_put_chars+0x8>
30: e1a00002 mov r0, r2
34: e12fff1e bx lr
which looks better and actually works. Mark all the inline
assembly in this file as volatile since we don't want the
compiler to optimize away these statements or move them around
in any way.
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCH_DMA is not always enabled when a user uses PCH_UART.
Since overhead of DMA is not small, in case of low frequent
communication, without DMA is better.
Thus, "select PCH_DMA" and DMADEVICES are unnecessary
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support ML7213 device of OKI SEMICONDUCTOR.
ML7213 is companion chip of Intel Atom E6xx series for IVI(In-Vehicle Infotainment).
ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some platforms, we need to restore the console speed on resume even
it was not suspended (no_console_suspend), and on others we don't have
to do that.
So don't care about the "console_suspend_enabled" and unconditionally
reset the console speed if it is a console.
This is actually a redo of ba15ab0 (Set proper console speed on resume
if console suspend is disabled) from Deepak Saxena. I also tried to
investigate more to find out if this change will break others, here is
what I've found out:
commit 891b9dd107
Author: Jason Wang <jason77.wang@gmail.com>
serial-core: restore termios settings when resume console ports
commit ca2e71aa8c
Author: Jason Wang <jason77.wang@gmail.com>
serial-core: skip call set_termios/console_start when no_console_suspend
commit 4547be7809
Author: Stanislav Brabec <sbrabec@suse.cz>
serial-core: resume serial hardware with no_console_suspend
commit ba15ab0e8d
Author: Deepak Saxena <dsaxena@laptop.org>
Set proper console speed on resume if console suspend is disabled
from ba15ab0, we learned that, even if the console suspend is disabled
(when no_console_suspend is set), we may still need to "reset the port
to the state it was in before we suspended."
Then with 4547be7, this piece of code is removed.
And then Jason Wang added that back in ca2e71a and 891b9dd, to fix
some breakage on OMAP3EVM platform. From ca2e71a we learned that the
"set_termios" things is actually needed by both console is suspended
and not suspended.
That's why I removed the console_suspended_enabled condition, and only
call console_start() when we actually suspeneded it.
I also noticed in this thread:
http://marc.info/?t=129079257100004&r=1&w=2, which talked about on
some platforms, UART HW will be cut power whether or not we set
no_console_suspend, and then on resume it does not work quite well. I
have a similar HW, and this patch fixed this issue, don't know if this
patch also works on their platforms.
[Update: Stanislav tested this patch on Zaurus and reported it improves the
situation. Thanks.]
CC: Greg KH <greg@kroah.com>
CC: Deepak Saxena <dsaxena@laptop.org>
CC: Jason Wang <jason77.wang@gmail.com>
CC: Stanislav Brabec <sbrabec@suse.cz>
CC: Daniel Drake <dsd@laptop.org>
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is used to store the spi_device ->modalias so they have to be the same
size. SPI_NAME_SIZE is 32.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flush_scheduled_work() is scheduled to be deprecated. Explicitly sync
flush the used work items instead. Note that before this change,
flush_scheduled_work() wouldn't have properly flushed tty->buf.work if
it were on timer.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OMAP can do also dynamic idling so wake-up enable register should be set
also while system is running. If UART_OMAP_WER is not set, then for instance
the RX activity cannot wake up the UART port that is sleeping.
This RX wake-up feature was working when the 8250 driver was used instead
of omap-serial. Reason for this is that the 8250 doesn't set the
UART_OMAP_WER and then arch/arm/mach-omap2/pm34xx.c ends up saving and
restoring the reset default which is the same than value
OMAP_UART_WER_MOD_WKUP here.
Fix this by moving the conditional UART_OMAP_WER write from serial_omap_pm
into serial_omap_startup where wake-up bits are set unconditionally.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Magic SysRq key is not working for OMAP on new serial
console ttyOx because SUPPORT_SYSRQ is not defined
for omap-serial.
This patch defines SUPPORT_SYSRQ in omap-serial and
enables handling of Magic SysRq character.
Further there is an issue of losing first break character.
Removing the reset of the lsr_break_flag fixes this issue.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Manjunath G Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some platform attributes (e.g. max_hz, use_dma) were being intuited
from the modem type. These things should be specified by the platform
data.
Added max_hz, use_dma to ifx_modem_platform_data definition,
replaced is_6160 w/ modem_type, and changed clients accordingly
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is kind of a revert for commit 669b7a0938 "hsu: add a periodic
timer to check dma rx channel", which is a workaround for a bug in A0
stepping silicon, where a dma rx data timeout is missing for some case.
Since new silicon has fixed it and the old version is phasing out, no
need to carry on it any more.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sport->port.irq is unsigned, check for <0 doesn't make sense.
Explicitly cast it to int to check for error.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arch/arm/mach-omap2/dma.c: Convert IS_ERR result to PTR_ERR
arm: omap2: mux: fix compile warning
omap1: Simplify use of omap_irq_flags
omap2+: Fix unused variable warning for omap_irq_base
Fix kernel-doc warning in kernel.h from commit 7ef88ad561
("BUILD_BUG_ON: make it handle more cases"):
Warning(include/linux/kernel.h:605): No description found for parameter 'condition'
Warning(include/linux/kernel.h:605): Excess function parameter 'cond' description in 'BUILD_BUG_ON'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patches should keep coming through Rusty but it helps if I'm Cc'd as
well.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (42 commits)
usb: gadget: composite: avoid access beyond array max length
USB: serial: handle Data Carrier Detect changes
USB: gadget: Fix endpoint representation in ci13xxx_udc
USB: gadget: Fix error path in ci13xxx_udc gadget probe function
usb: pch_udc: Fix the worning log issue at gadget driver remove
USB: serial: Updated support for ICOM devices
USB: ehci-mxc: add work-around for efika mx/sb bug
USB: unbreak ehci-mxc on otg port of i.MX27
drivers: update to pl2303 usb-serial to support Motorola cables
USB: adding USB support for Cinterion's HC2x, EU3 and PH8 products
USB serial: add missing .usb_driver field in serial drivers
USB: ehci-fsl: Fix 'have_sysif_regs' detection
USB: g_printer: fix bug in module parameter definitions
USB: g_printer: fix bug in unregistration
USB: uss720: remove duplicate USB device
MAINTAINERS: add ueagle-atm entry
USB: EHCI: fix DMA deallocation bug
USB: pch_udc: support new device ML7213 IOH
usb: pch_udc: Fixed issue which does not work with g_serial
usb: set ep_dev async suspend should be later than device_initialize
...
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (26 commits)
staging: r8712u: Add new device IDs
staging: brcm80211: fix suspend/resume issue in brcmsmac
staging: brcm80211: remove assert to avoid panic since 2.6.37 kernel
Staging: iio: Aditional fixpoint formatted output bugfix
staging: usbip: vhci: use urb->dev->portnum to find port
staging: usbip: vhci: handle EAGAIN from SO_RCVTIMEO
staging: usbip: vhci: friendly log messages for connection errors
staging: usbip: vhci: refuse to enqueue for dead connections
staging: usbip: vhci: give back URBs from in-flight unlink requests
staging: usbip: vhci: update reference count for usb_device
staging: usbip: stub: update refcounts for devices and interfaces
staging: tidspbridge: replace mbox callback with notifier_call
staging: comedi: ni_labpc: Use shared IRQ for PCMCIA card
Staging: speakup: &&/|| confusion in silent_store()
iio: Fixpoint formatted output bugfix
staging: rt2860: Fix incorrect netif_stop_queue usage warning
staging: r8712u: Fix memory leak in firmware loading
staging: tidspbridge: configure full L1 MMU range
staging: rt2870sta: Add ID for Linksys WUSB100v2
Staging: xgfib: put parenthesis in the right place
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/serial: fix apbuart build
n_hdlc: fix read and write locking
serial: unbreak billionton CF card
tty: use for_each_console() and WARN() on sysfs failures
vt: fix issue when fbcon wants to takeover a second time.
Fix up trivial conflict in drivers/tty/tty_io.c
Allow non-ARM SMP processors to use the SMP_ON_UP feature. CPUs
supporting SMP must have the new CPU ID format, so check for this first.
Then check for ARM11MPCore, which fails the MPIDR check. Lastly check
the MPIDR reports multiprocessing extensions and that the CPU is part of
a multiprocessing system.
Cc: <stable@kernel.org>
Reported-and-Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the ISA/PCI IO space accessors are properly ordered on
ARMv6+ architectures. These should always be ordered with respect to
all other accesses.
This also fixes __iormb() and __iowmb() not being visible to ioread/
iowrite if a platform defines its own MMIO accessors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Disable the initrd if the passed address already overlaps the reserved
region. This avoids oopses on Netwinders when NeTTrom tells the kernel
that an initrd is located at mem+4MB, but this overlaps the BSS,
resulting in the kernels in-use BSS being freed.
This should be applied to v2.6.37-stable.
Cc: <stable@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
0ea1293 (arm: return both physical and virtual addresses from addruart)
changed the way the 'addruart' worked, making it return both the virt
and phys addresses. Unfortunately, for footbridge, these were reversed.
Fix that. Tested on Netwinder.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We should not report incomplete blocks on error. Return the number of
bytes successfully transferred, rounded down to the nearest block.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we encounter an error, make sure we complete the transaction
otherwise we'll leave the request dangling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not respond with -EINVAL to EVIOCGKEYCODE for not-yet-mapped
scancodes, but rather return KEY_RESERVED.
This fixes breakage with Ubuntu's input-kbd utility that stopped
returning full keymaps for remote controls.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Mark Lord <kernel@teksavvy.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since check_prlimit_permission always fails in the case of SUID/GUID
processes, such processes are not able to read or set their own limits.
This commit changes this by assuming that process can always read/change
its own limits.
Signed-off-by: Kacper Kornet <kornet@camk.edu.pl>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
