Currently the opal_exit tracepoint usually shows the opcode as 0:
<idle>-0 [047] d.h. 635.654292: opal_entry: opcode=63
<idle>-0 [047] d.h. 635.654296: opal_exit: opcode=0 retval=0
kopald-1209 [019] d... 636.420943: opal_entry: opcode=10
kopald-1209 [019] d... 636.420959: opal_exit: opcode=0 retval=0
This is because we incorrectly load the opcode into r0 before calling
__trace_opal_exit(), whereas it expects the opcode in r3 (first function
parameter). In fact we are leaving the retval in r3, so opcode and
retval will always show the same value.
Instead load the opcode into r3, resulting in:
<idle>-0 [040] d.h. 636.618625: opal_entry: opcode=63
<idle>-0 [040] d.h. 636.618627: opal_exit: opcode=63 retval=0
Fixes: c49f63530b ("powernv: Add OPAL tracepoints")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All entry points already read the MSR so they can easily do
the right thing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 contains an off core mmu called the nest mmu (NMMU). This is
used by other hardware units on the chip to translate virtual
addresses into real addresses. The unit attempting an address
translation provides the majority of the context required for the
translation request except for the base address of the partition table
(ie. the PTCR) which needs to be programmed into the NMMU.
This patch adds a call to OPAL to set the PTCR for the nest mmu in
opal_init().
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This defines real-mode versions of opal_int_get_xirr(), opal_int_eoi()
and opal_int_set_mfrr(), for use by KVM real-mode code.
It also exports opal_int_set_mfrr() so that the modular part of KVM
can use it to send IPIs.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a guest has a PCI pass-through device with an interrupt, it
will direct the interrupt to a particular guest VCPU. In fact the
physical interrupt might arrive on any CPU, and then get
delivered to the target VCPU in the emulated XICS (guest interrupt
controller), and eventually delivered to the target VCPU.
Now that we have code to handle device interrupts in real mode
without exiting to the host kernel, there is an advantage to having
the device interrupt arrive on the same sub(core) as the target
VCPU is running on. In this situation, the interrupt can be
delivered to the target VCPU without any exit to the host kernel
(using a hypervisor doorbell interrupt between threads if
necessary).
This patch aims to get passed-through device interrupts arriving
on the correct core by setting the interrupt server in the real
hardware XICS for the interrupt to the first thread in the (sub)core
where its target VCPU is running. We do this in the real-mode H_EOI
code because the H_EOI handler already needs to look at the
emulated ICS state for the interrupt (whereas the H_XIRR handler
doesn't), and we know we are running in the target VCPU context
at that point.
We set the server CPU in hardware using an OPAL call, regardless of
what the IRQ affinity mask for the interrupt says, and without
updating the affinity mask. This amounts to saying that when an
interrupt is passed through to a guest, as a matter of policy we
allow the guest's affinity for the interrupt to override the host's.
This is inspired by an earlier patch from Suresh Warrier, although
none of this code came from that earlier patch.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
VGIC implementation.
- s390: support for trapping software breakpoints, nested virtualization
(vSIE), the STHYI opcode, initial extensions for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots of cleanups,
preliminary to this and the upcoming support for hardware virtualization
extensions.
- x86: support for execute-only mappings in nested EPT; reduced vmexit
latency for TSC deadline timer (by about 30%) on Intel hosts; support for
more than 255 vCPUs.
- PPC: bugfixes.
The ugly bit is the conflicts. A couple of them are simple conflicts due
to 4.7 fixes, but most of them are with other trees. There was definitely
too much reliance on Acked-by here. Some conflicts are for KVM patches
where _I_ gave my Acked-by, but the worst are for this pull request's
patches that touch files outside arch/*/kvm. KVM submaintainers should
probably learn to synchronize better with arch maintainers, with the
latter providing topic branches whenever possible instead of Acked-by.
This is what we do with arch/x86. And I should learn to refuse pull
requests when linux-next sends scary signals, even if that means that
submaintainers have to rebase their branches.
Anyhow, here's the list:
- arch/x86/kvm/vmx.c: handle_pcommit and EXIT_REASON_PCOMMIT was removed
by the nvdimm tree. This tree adds handle_preemption_timer and
EXIT_REASON_PREEMPTION_TIMER at the same place. In general all mentions
of pcommit have to go.
There is also a conflict between a stable fix and this patch, where the
stable fix removed the vmx_create_pml_buffer function and its call.
- virt/kvm/kvm_main.c: kvm_cpu_notifier was removed by the hotplug tree.
This tree adds kvm_io_bus_get_dev at the same place.
- virt/kvm/arm/vgic.c: a few final bugfixes went into 4.7 before the
file was completely removed for 4.8.
- include/linux/irqchip/arm-gic-v3.h: this one is entirely our fault;
this is a change that should have gone in through the irqchip tree and
pulled by kvm-arm. I think I would have rejected this kvm-arm pull
request. The KVM version is the right one, except that it lacks
GITS_BASER_PAGES_SHIFT.
- arch/powerpc: what a mess. For the idle_book3s.S conflict, the KVM
tree is the right one; everything else is trivial. In this case I am
not quite sure what went wrong. The commit that is causing the mess
(fd7bacbca4, "KVM: PPC: Book3S HV: Fix TB corruption in guest exit
path on HMI interrupt", 2016-05-15) touches both arch/powerpc/kernel/
and arch/powerpc/kvm/. It's large, but at 396 insertions/5 deletions
I guessed that it wasn't really possible to split it and that the 5
deletions wouldn't conflict. That wasn't the case.
- arch/s390: also messy. First is hypfs_diag.c where the KVM tree
moved some code and the s390 tree patched it. You have to reapply the
relevant part of commits 6c22c98637, plus all of e030c1125e, to
arch/s390/kernel/diag.c. Or pick the linux-next conflict
resolution from http://marc.info/?l=kvm&m=146717549531603&w=2.
Second, there is a conflict in gmap.c between a stable fix and 4.8.
The KVM version here is the correct one.
I have pushed my resolution at refs/heads/merge-20160802 (commit
3d1f53419842) at git://git.kernel.org/pub/scm/virt/kvm/kvm.git.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXoGm7AAoJEL/70l94x66DugQIAIj703ePAFepB/fCrKHkZZia
SGrsBdvAtNsOhr7FQ5qvvjLxiv/cv7CymeuJivX8H+4kuUHUllDzey+RPHYHD9X7
U6n1PdCH9F15a3IXc8tDjlDdOMNIKJixYuq1UyNZMU6NFwl00+TZf9JF8A2US65b
x/41W98ilL6nNBAsoDVmCLtPNWAqQ3lajaZELGfcqRQ9ZGKcAYOaLFXHv2YHf2XC
qIDMf+slBGSQ66UoATnYV2gAopNlWbZ7n0vO6tE2KyvhHZ1m399aBX1+k8la/0JI
69r+Tz7ZHUSFtmlmyByi5IAB87myy2WQHyAPwj+4vwJkDGPcl0TrupzbG7+T05Y=
=42ti
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
- ARM: GICv3 ITS emulation and various fixes. Removal of the
old VGIC implementation.
- s390: support for trapping software breakpoints, nested
virtualization (vSIE), the STHYI opcode, initial extensions
for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots
of cleanups, preliminary to this and the upcoming support for
hardware virtualization extensions.
- x86: support for execute-only mappings in nested EPT; reduced
vmexit latency for TSC deadline timer (by about 30%) on Intel
hosts; support for more than 255 vCPUs.
- PPC: bugfixes.
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (302 commits)
KVM: PPC: Introduce KVM_CAP_PPC_HTM
MIPS: Select HAVE_KVM for MIPS64_R{2,6}
MIPS: KVM: Reset CP0_PageMask during host TLB flush
MIPS: KVM: Fix ptr->int cast via KVM_GUEST_KSEGX()
MIPS: KVM: Sign extend MFC0/RDHWR results
MIPS: KVM: Fix 64-bit big endian dynamic translation
MIPS: KVM: Fail if ebase doesn't fit in CP0_EBase
MIPS: KVM: Use 64-bit CP0_EBase when appropriate
MIPS: KVM: Set CP0_Status.KX on MIPS64
MIPS: KVM: Make entry code MIPS64 friendly
MIPS: KVM: Use kmap instead of CKSEG0ADDR()
MIPS: KVM: Use virt_to_phys() to get commpage PFN
MIPS: Fix definition of KSEGX() for 64-bit
KVM: VMX: Add VMCS to CPU's loaded VMCSs before VMPTRLD
kvm: x86: nVMX: maintain internal copy of current VMCS
KVM: PPC: Book3S HV: Save/restore TM state in H_CEDE
KVM: PPC: Book3S HV: Pull out TM state save/restore into separate procedures
KVM: arm64: vgic-its: Simplify MAPI error handling
KVM: arm64: vgic-its: Make vgic_its_cmd_handle_mapi similar to other handlers
KVM: arm64: vgic-its: Turn device_id validation into generic ID validation
...
Replace the old generic opal_call_realmode() with proper per-call
wrappers similar to the normal ones and convert callers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPAL provides an emulated XICS interrupt controller to
use as a fallback on newer processors that don't have a
XICS. It's meant as a way to provide backward compatibility
with future processors. Add the corresponding interfaces.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implement new character device driver to allow access from user space
to the operator panel display present on IBM Power Systems machines
with FSPs.
This will allow status information to be presented on the display which
is visible to a user.
The driver implements a character buffer which a user can read/write
by accessing the device (/dev/op_panel). This buffer is then displayed on
the operator panel display. Any attempt to write past the last character
position will have no effect and attempts to write more characters than
the size of the display will be truncated. The device may only be accessed
by a single process at a time.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This exports 4 functions, which base on the corresponding OPAL
APIs to get/set PCI slot status. Those functions are going to
be used by PowerNV PCI hotplug driver:
pnv_pci_get_device_tree() opal_get_device_tree()
pnv_pci_get_presence_state() opal_pci_get_presence_state()
pnv_pci_get_power_state() opal_pci_get_power_state()
pnv_pci_set_power_state() opal_pci_set_power_state()
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPAL_CALL wrapper code sticks the r1 (stack pointer) into PACAR1 purely
for debugging purpose only. The power7_wakeup* functions relies on stack
pointer saved in PACAR1. Any opal call made using opal wrapper (directly
or in-directly) before we fall through power7_wakeup*, then it ends up
replacing r1 in PACAR1(r13) leading to kernel panic. So far we don't see
any issues because we have never made any opal calls using OPAL wrapper
before power7_wakeup*. But the subsequent HMI patch would need to invoke
C calls during cpu wakeup/idle path that in-directly makes opal call using
opal wrapper. This patch facilitates the subsequent HMI patch by removing
usage of PACAR1 from opal call wrapper.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On BMC machines, console output is controlled by the OPAL firmware and is
only flushed when its pollers are called. When the kernel is in a panic
state, it no longer calls these pollers and thus console output does not
completely flush, causing some output from the panic to be lost.
Output is only actually lost when the kernel is configured to not power off
or reboot after panic (i.e. CONFIG_PANIC_TIMEOUT is set to 0) since OPAL
flushes the console buffer as part of its power down routines. Before this
patch, however, only partial output would be printed during the timeout wait.
This patch adds a new kmsg_dumper which gets called at panic time to ensure
panic output is not lost. It accomplishes this by calling OPAL_CONSOLE_FLUSH
in the OPAL API, and if that is not available, the pollers are called enough
times to (hopefully) completely flush the buffer.
The flushing mechanism will only affect output printed at and before the
kmsg_dump call in kernel/panic.c:panic(). As such, the "end Kernel panic"
message may still be truncated as follows:
>Call Trace:
>[c000000f1f603b00] [c0000000008e9458] dump_stack+0x90/0xbc (unreliable)
>[c000000f1f603b30] [c0000000008e7e78] panic+0xf8/0x2c4
>[c000000f1f603bc0] [c000000000be4860] mount_block_root+0x288/0x33c
>[c000000f1f603c80] [c000000000be4d14] prepare_namespace+0x1f4/0x254
>[c000000f1f603d00] [c000000000be43e8] kernel_init_freeable+0x318/0x350
>[c000000f1f603dc0] [c00000000000bd74] kernel_init+0x24/0x130
>[c000000f1f603e30] [c0000000000095b0] ret_from_kernel_thread+0x5c/0xac
>---[ end Kernel panic - not
This functionality is implemented as a kmsg_dumper as it seems to be the
most sensible way to introduce platform-specific functionality to the
panic function.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch registers the following two new OPAL interfaces calls
for the platform LED subsystem. With the help of these new OPAL calls,
the kernel will be able to get or set the state of various individual
LEDs on the system at any given location code which is passed through
the LED specific device tree nodes.
(1) OPAL_LEDS_GET_INDICATOR opal_leds_get_ind
(2) OPAL_LEDS_SET_INDICATOR opal_leds_set_ind
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On non-recoverable MCE errors in kernel space, Linux kernel panics
and system reboots. On BMC based system opal-prd runs as a daemon
in the host. Hence, kernel crash may prevent opal-prd to detect and
analyze this MCE error. This may land us in a situation where the faulty
memory never gets de-configured and Linux would keep hitting same MCE error
again and again. If this happens in early stage of kernel initialization,
then Linux will keep crashing and rebooting in a loop.
This patch fixes this issue by invoking new opal_cec_reboot2() call with
reboot type OPAL_REBOOT_PLATFORM_ERROR to inform BMC/OCC about this
error, so that BMC can collect relevant data for error analysis and
decide what component to de-configure before rebooting.
This patch is dependent on OPAL patchset posted on skiboot mailing list
at https://lists.ozlabs.org/pipermail/skiboot/2015-July/001771.html that
introduces opal_cec_reboot2() opal call.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds support for OPAL EPOW (Environmental and Power Warnings)
and DPO (Delayed Power Off) events for the PowerNV platform. These events
are generated on FSP (Flexible Service Processor) based systems. EPOW
events are generated due to various critical system conditions that
require system shutdown. A few examples of these conditions are high
ambient temperature or system running on UPS power with low UPS battery.
DPO event is generated in response to admin initiated system shutdown
request. Upon receipt of EPOW and DPO events the host kernel invokes
orderly_poweroff() for performing graceful system shutdown.
Signed-off-by: Vipin K Parashar <vipin@linux.vnet.ibm.com>
Acked-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This change adds a char device to access the "PRD" (processor runtime
diagnostics) channel to OPAL firmware.
Includes contributions from Vaidyanathan Srinivasan, Neelesh Gupta &
Vishal Kulkarni.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fastsleep is one of the idle state which cpuidle subsystem currently
uses on power8 machines. In this state L2 cache is brought down to a
threshold voltage. Therefore when the core is in fastsleep, the
communication between L2 and L3 needs to be fenced. But there is a bug
in the current power8 chips surrounding this fencing.
OPAL provides a workaround which precludes the possibility of hitting
this bug. But running with this workaround applied causes checkstop
if any correctable error in L2 cache directory is detected. Hence OPAL
also provides a way to undo the workaround.
In the existing implementation, workaround is applied by the last thread
of the core entering fastsleep and undone by the first thread waking up.
But this has a performance cost. These OPAL calls account for roughly
4000 cycles everytime the core has to enter or wakeup from fastsleep.
This patch introduces a sysfs attribute (fastsleep_workaround_applyonce)
to choose the behavior of this workaround.
By default, fastsleep_workaround_applyonce = 0. In this case, workaround
is applied/undone everytime the core enters/exits fastsleep.
fastsleep_workaround_applyonce = 1. In this case the workaround is
applied once on all the cores and never undone. This can be triggered by
echo 1 > /sys/devices/system/cpu/fastsleep_workaround_applyonce
For simplicity this attribute can be modified only once. Implying, once
fastsleep_workaround_applyonce is changed to 1, it cannot be reverted
to the default state.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
This change adds the OPAL interface definitions to allow Linux to read,
write and erase from system flash devices. We register platform devices
for the flash devices exported by firmware.
We clash with the existing opal_flash_init function, which is really for
the FSP flash update functionality, so we rename that initcall to
opal_flash_update_init().
A future change will add an mtd driver that uses this interface.
Changes from Joel Stanley and Jeremy Kerr.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This commit gets opal-api.h to mostly match the version in Skiboot as of
commit ea7d806ab0ba.
The exceptions are things which are not (currently) used in Linux.
Most of this is just whitespace and a few things moving around. I think
the diff is readable.
Also OpalMessageType became opal_msg_type, requiring a change in the
Linux code.
Finally Skiboot and Linux disagree on CAPI vs CXL, because CAPI means
something else in Linux. To handle that we just point the Linux wrapper,
which is named "cxl" to the OPAL token OPAL_PCI_SET_PHB_CAPI_MODE.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Patch c49f63530b ("powernv: Add OPAL tracepoints") has a spurious
store to the stack:
ld r12,opal_tracepoint_refcount@toc(r2); \
std r12,32(r1); \
The store was originally used to save the current tracepoint status
so the entry and the exit tracepoints were always balanced. In the
end I just created a separate path when tracepoints are enabled.
The offset on the stack used for this store is not valid for ABIv2
and it causes strange issues. I noticed it because OPAL console input
was broken.
Fixes: c49f63530b ("powernv: Add OPAL tracepoints")
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Winkle is a deep idle state supported in power8 chips. A core enters
winkle when all the threads of the core enter winkle. In this state
power supply to the entire chiplet i.e core, private L2 and private L3
is turned off. As a result it gives higher powersavings compared to
sleep.
But entering winkle results in a total hypervisor state loss. Hence the
hypervisor context has to be preserved before entering winkle and
restored upon wake up.
Power-on Reset Engine (PORE) is a dedicated engine which is responsible
for powering on the chiplet during wake up. It can be programmed to
restore the register contests of a few specific registers. This patch
uses PORE to restore register state wherever possible and uses stack to
save and restore rest of the necessary registers.
With hypervisor state restore things fall under three categories-
per-core state, per-subcore state and per-thread state. To manage this,
extend the infrastructure introduced for sleep. Mainly we add a paca
variable subcore_sibling_mask. Using this and the core_idle_state we can
distingush first thread in core and subcore.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Deep idle states like sleep and winkle are per core idle states. A core
enters these states only when all the threads enter either the
particular idle state or a deeper one. There are tasks like fastsleep
hardware bug workaround and hypervisor core state save which have to be
done only by the last thread of the core entering deep idle state and
similarly tasks like timebase resync, hypervisor core register restore
that have to be done only by the first thread waking up from these
state.
The current idle state management does not have a way to distinguish the
first/last thread of the core waking/entering idle states. Tasks like
timebase resync are done for all the threads. This is not only is
suboptimal, but can cause functionality issues when subcores and kvm is
involved.
This patch adds the necessary infrastructure to track idle states of
threads in a per-core structure. It uses this info to perform tasks like
fastsleep workaround and timebase resync only once per core.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Originally-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch exposes the available i2c busses on the PowerNV platform
to the kernel and implements the bus driver to support i2c and
smbus commands.
The driver uses the platform device infrastructure to probe the busses
on the platform and registers them with the i2c driver framework.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> (I2C part, excluding the bindings)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch implements the OPAL rtc driver that binds with the rtc
driver subsystem. The driver uses the platform device infrastructure
to probe the rtc device and register it to rtc class framework. The
'wakeup' is supported depending upon the property 'has-tpo' present
in the OF node. It provides a way to load the generic rtc driver in
in the absence of an OPAL driver.
The patch also moves the existing OPAL rtc get/set time interfaces to the
new driver and exposes the necessary OPAL calls using EXPORT_SYMBOL_GPL.
Test results:
-------------
Host:
[root@tul169p1 ~]# ls -l /sys/class/rtc/
total 0
lrwxrwxrwx 1 root root 0 Oct 14 03:07 rtc0 -> ../../devices/opal-rtc/rtc/rtc0
[root@tul169p1 ~]# cat /sys/devices/opal-rtc/rtc/rtc0/time
08:10:07
[root@tul169p1 ~]# echo `date '+%s' -d '+ 2 minutes'` > /sys/class/rtc/rtc0/wakealarm
[root@tul169p1 ~]# cat /sys/class/rtc/rtc0/wakealarm
1413274345
[root@tul169p1 ~]#
FSP:
$ smgr mfgState
standby
$ rtim timeofday
System time is valid: 2014/10/14 08:12:04.225115
$ smgr mfgState
ipling
$
CC: devicetree@vger.kernel.org
CC: tglx@linutronix.de
CC: rtc-linux@googlegroups.com
CC: a.zummo@towertech.it
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Recent OPAL firmare adds a couple of functions to send and receive IPMI
messages:
https://github.com/open-power/skiboot/commit/b2a374da
This change updates the token list and wrappers to suit, and adds the
platform devices for any IPMI interfaces.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d4fe0965e2 ("powerpc/jump_label: use HAVE_JUMP_LABEL?")
missed a few conversions. Change the remaining uses of
CONFIG_JUMP_LABEL to HAVE_JUMP_LABEL.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, we can't call opal wrappers from modules when using the LE
ABIv2, which requires a TOC init. If we do we'll try and load the opal
entry point using the wrong toc and probably explode or worse jump to
the wrong address.
Nothing in upstream is making opal calls from a module, but we do export
one of the wrappers so we should fix this anyway.
This change uses the _GLOBAL_TOC() macro (rather than _GLOBAL) for the
opal wrappers, so that we can do non-local calls to them.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds the OPAL call to change a PHB into cxl mode.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently there is no way to generically check if an OPAL call exists or not
from the host kernel.
This adds an OPAL call opal_check_token() which tells you if the given token is
present in OPAL or not.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PowerNV platform is capable of capturing host memory region when system
crashes (because of host/firmware). We have new OPAL API to register/
unregister memory region to be captured when system crashes.
This patch adds support for new API. Also during boot time we register
kernel log buffer and unregister before doing kexec.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we hit the HMI in Linux, invoke opal call to handle/recover from HMI
errors in real mode and then in virtual mode during check_irq_replay()
invoke opal_poll_events()/opal_do_notifier() to retrieve HMI event from
OPAL and act accordingly.
Now that we are ready to handle HMI interrupt directly in linux, remove
the HMI interrupt registration with firmware.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch synchronizes header file with firmware to have new OPAL
API opal_pci_eeh_freeze_set(), which is used to freeze the specified
PE in order to support "compound" PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Knowing how long we spend in firmware calls is an important part of
minimising OS jitter.
This patch adds tracepoints to each OPAL call. If tracepoints are
enabled we branch out to a common routine that calls an entry and exit
tracepoint.
This allows us to write tools that monitor the frequency and duration
of OPAL calls, eg:
name count total(ms) min(ms) max(ms) avg(ms) period(ms)
OPAL_HANDLE_INTERRUPT 5 0.199 0.037 0.042 0.040 12547.545
OPAL_POLL_EVENTS 204 2.590 0.012 0.036 0.013 2264.899
OPAL_PCI_MSI_EOI 2830 3.066 0.001 0.005 0.001 81.166
We use jump labels if configured, which means we only add a single
nop instruction to every OPAL call when the tracepoints are disabled.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When running as a powernv "host" system on P8, we need to switch
the endianness of interrupt handlers. This does it via the appropriate
call to the OPAL firmware which may result in just switching HID0:HILE
but depending on the processor version might need to do a few more
things. This call must be done early before any other processor has
been brought out of firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a number of places where we load the text address of a local
function and indirectly branch to it in assembly. Since it is an
indirect branch binutils will not know to use the function text
address, so that trick wont work.
There is no need for these functions to have a function descriptor
so we can replace it with a label and remove the dot symbol.
Signed-off-by: Anton Blanchard <anton@samba.org>
This call will not be understood by OPAL, and cause it to add an error
to it's log. Among other things, this is useful for testing the
behaviour of the log as it fills up.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc non-virtualized cpuidle from Ben Herrenschmidt:
"This is the branch I mentioned in my other pull request which contains
our improved cpuidle support for the "powernv" platform
(non-virtualized).
It adds support for the "fast sleep" feature of the processor which
provides higher power savings than our usual "nap" mode but at the
cost of losing the timers while asleep, and thus exploits the new
timer broadcast framework to work around that limitation.
It's based on a tip timer tree that you seem to have already merged"
* 'powernv-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
cpuidle/powernv: Parse device tree to setup idle states
cpuidle/powernv: Add "Fast-Sleep" CPU idle state
powerpc/powernv: Add OPAL call to resync timebase on wakeup
powerpc/powernv: Add context management for Fast Sleep
powerpc: Split timer_interrupt() into timer handling and interrupt handling routines
powerpc: Implement tick broadcast IPI as a fixed IPI message
powerpc: Free up the slot of PPC_MSG_CALL_FUNC_SINGLE IPI message
This patch enables fetching of various platform sensor data through
OPAL and expects a sensor handle from the driver to pass to OPAL.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables reading and updating of system parameters through
OPAL call.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This enables support for userspace to fetch and initiate FSP and
Platform dumps from the service processor (via firmware) through sysfs.
Based on original patch from Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Flow:
- We register for OPAL notification events.
- OPAL sends new dump available notification.
- We make information on dump available via sysfs
- Userspace requests dump contents
- We retrieve the dump via OPAL interface
- User copies the dump data
- userspace sends ack for dump
- We send ACK to OPAL.
sysfs files:
- We add the /sys/firmware/opal/dump directory
- echoing 1 (well, anything, but in future we may support
different dump types) to /sys/firmware/opal/dump/initiate_dump
will initiate a dump.
- Each dump that we've been notified of gets a directory
in /sys/firmware/opal/dump/ with a name of the dump type and ID (in hex,
as this is what's used elsewhere to identify the dump).
- Each dump has files: id, type, dump and acknowledge
dump is binary and is the dump itself.
echoing 'ack' to acknowledge (currently any string will do) will
acknowledge the dump and it will soon after disappear from sysfs.
OPAL APIs:
- opal_dump_init()
- opal_dump_info()
- opal_dump_read()
- opal_dump_ack()
- opal_dump_resend_notification()
Currently we are only ever notified for one dump at a time (until
the user explicitly acks the current dump, then we get a notification
of the next dump), but this kernel code should "just work" when OPAL
starts notifying us of all the dumps present.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on a patch by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
This patch adds support to read error logs from OPAL and export
them to userspace through a sysfs interface.
We export each log entry as a directory in /sys/firmware/opal/elog/
Currently, OPAL will buffer up to 128 error log records, we don't
need to have any knowledge of this limit on the Linux side as that
is actually largely transparent to us.
Each error log entry has the following files: id, type, acknowledge, raw.
Currently we just export the raw binary error log in the 'raw' attribute.
In a future patch, we may parse more of the error log to make it a bit
easier for userspace (e.g. to be able to display a brief summary in
petitboot without having to have a full parser).
If we have >128 logs from OPAL, we'll only be notified of 128 until
userspace starts acknowledging them. This limitation may be lifted in
the future and with this patch, that should "just work" from the linux side.
A userspace daemon should:
- wait for error log entries using normal mechanisms (we announce creation)
- read error log entry
- save error log entry safely to disk
- acknowledge the error log entry
- rinse, repeat.
On the Linux side, we read the error log when we're notified of it. This
possibly isn't ideal as it would be better to only read them on-demand.
However, this doesn't really work with current OPAL interface, so we
read the error log immediately when notified at the moment.
I've tested this pretty extensively and am rather confident that the
linux side of things works rather well. There is currently an issue with
the service processor side of things for >128 error logs though.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During "Fast-sleep" and deeper power savings state, decrementer and
timebase could be stopped making it out of sync with rest
of the cores in the system.
Add a firmware call to request platform to resync timebase
using low level platform methods.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Its possible that OPAL may be writing to host memory during
kexec (like dump retrieve scenario). In this situation we might
end up corrupting host memory.
This patch makes OPAL sync call to make sure OPAL stops
writing to host memory before kexec'ing.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Opal now has a new messaging infrastructure to push the messages to
linux in a generic format for different type of messages using only one
event bit. The format of the opal message is as below:
struct opal_msg {
uint32_t msg_type;
uint32_t reserved;
uint64_t params[8];
};
This patch allows clients to subscribe for notification for specific
message type. It is upto the subscriber to decipher the messages who showed
interested in receiving specific message type.
The interface to subscribe for notification is:
int opal_message_notifier_register(enum OpalMessageType msg_type,
struct notifier_block *nb)
The notifier will fetch the opal message when available and notify the
subscriber with message type and the opal message. It is subscribers
responsibility to copy the message data before returning from notifier
callback.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Code update interface for powernv platform. This provides
sysfs interface to pass new image, validate, update and
commit images.
This patch includes:
- Below OPAL APIs for code update
- opal_validate_flash()
- opal_manage_flash()
- opal_update_flash()
- Create below sysfs files under /sys/firmware/opal
- image : Interface to pass new FW image
- validate_flash : Validate candidate image
- manage_flash : Commit/Reject operations
- update_flash : Flash new candidate image
Updating Image:
"update_flash" is an interface to indicate flash new FW.
It just passes image SG list to FW. Actual flashing is done
during system reboot time.
Note:
- SG entry format:
I have kept version number to keep this list similar to what
PAPR is defined.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
