AES32 supports the non-standard 128kHZ, and this is enabled only when
SNDRV_PCM_RATE_KNOT is set in hw.rates field.
Tested-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Newer RME cards like RayDAT and AIO support 32 samples per period. This
value is encoded as {1,1,1} in the HDSP_LatencyMask bits in the control
register.
Since {1,1,1} is also the representation for 8192 samples/period on
older RME cards, we have to special case 32 samples and 32768 bytes
according to the actual card.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, hdspm_decode_latency is called several times, violating the
DRY principle. Given that we need to distinguish between old and new
cards when decoding the latency bits in the control register, introduce
hdspm_get_latency() to provide the required functionality.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On newer RME cards like RayDAT and AIO, the 8192 samples per period size
are no longer supported. Instead, setting all three bits of
HDSP_LatencyMask to one ({1,1,1}) now corresponds to 32 samples per
period.
To make this more obvious to future developers, let's reorder the array
according to their bit representation, starting at 64 ({0,0,0}) up to
4096 ({1,1,0}) and finally 32 ({1,1,1}).
Note that this patch doesn't change semantics.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On newer RME cards like RayDAT and AIO, the lower bound is 32 samples
per period in contrast to 64 samples as seen on older cards.
We hence lower period_bytes_min to 32 * 4. Four bytes per sample.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Older RME cards like MADI and AES support period sizes of 8192 samples.
The original hdspm driver already featured this value, apparently, it
was lost during the rewrite.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put the exception checks for io_type switch() for possible mistakes in
future. Also this shuts up annoying compile warnings.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apparently, there are multiple old firmware revisions in the wild for
the PCI RME MADI cards. Just add them to the list of supported devices
and treat them like their modern counterparts.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In slave mode, the card can only detect the base frequency (32..48kHz)
on the MADI link (exception: 96k frames), so the real external sample
rate is this base frequency multiplied by 1, 2 or 4 depending on the
speed mode.
This patch enables 64..192kHz sample rates in clock slave mode, which
failed before due to an alleged sample rate mismatch between the MADI
link (e.g., 48kHz) and the application in DS/QS mode (e.g., 96kHz,
192kHz).
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When running in slave mode (no clock master), there is no way to
determine the real wirespeed on the MADI link (single/double/quad
speed). Like physical gear, simply provide the user with a tristate
switch to select the appropriate format.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The char can be unsigned on some architectures. Since the code checks
the negative values, they should be declared as signed char explicitly.
sound/pci/rme9652/hdspm.c:5449: warning: comparison is always false due to limited range of data type
sound/pci/rme9652/hdspm.c:5462: warning: comparison is always false due to limited range of data type
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI version of the RME HDSP MADI card uses 0xcf as revision ID. Just
add this to the list of supported cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When using Word Clock on RME MADI cards, AutoSync mode was alternating
betweeen MADI and WC due to a typo: AutoSync is indicated in the second
status register (status2), not the first one (status).
While the proc output was always correct, the reported WC frequency to
ALSA was unstable as mentioned in
http://mailman.alsa-project.org/pipermail/alsa-devel/2008-March/006723.html
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For the MIDI part, we need to acquire (and release) the hmidi->lock,
access to the global hdspm structure is serialized through
hmidi->hdspm->lock instead.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The name argument of request_irq() appears in /proc/interrupts, and
it's quite ugly when the name entry contains a space or special letters.
In general, it's simpler and more readable when the module name appears
there, so let's replace all entries with KBUILD_MODNAME.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The convention for pci_driver.name entry in kernel drivers seem to be
the module name or equivalent ones. But, so far, almost all PCI sound
drivers use more verbose name like "ABC Xyz (12)", and these are fairly
confusing when appearing as a file name.
This patch converts the all pci_driver.name entries in sound/pci/* to
use KBUILD_MODNAME for more unified appearance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current AES32 firmware revision ID is 234, however, a user confirmed
that everything works fine with the previous revision, too.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Depending on the model and the presence of a TCO module, the number of
midi ports varies. Some have 1 port (MADIface), some have 2 (default),
with TCO, there are 3.
Don't hardcode the number of midi ports to initialize.
This patch also fixes a boot lockup on MADIface.
[Coding-style fixes by tiwai]
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In contrast to the PCIe version (RME AES), the PCI version (RME AES32)
has a different firmware revision.
This patch adds the missing PCI revision.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Original patch by Dan Rosenberg <drosenberg@vsecurity.com> under commit
e68d3b316a. I'm copying his text here:
The SNDRV_HDSPM_IOCTL_GET_CONFIG_INFO ioctl in hdspm.c allow unprivileged
users to read uninitialized kernel stack memory, because several fields
of the hdspm_config struct declared on the stack are not altered
or zeroed before being copied back to the user. This patch takes care
of it.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fredrik Lingvall <fredrik.lingvall@gmail.com> has discovered wrong
frequency and sync detection on AES32. According to him, the provided
patch fixes these issues.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In contrast to the RME MADI card, coax/optical selection on the MADIface
is done via a physical switch located at the breakout box. Obviously,
the driver cannot switch ports in software.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Caused by two typos, no output channel mappings were assigned for
MADI/MADIface at double/quad speed.
The channel mapping is indeed identical to the single speed mapping, the
cards will simply use the first N channels.
Signed-off-by: Florian Faber <faber@faberman.de>
Signed-off-by: Fredrik Lingvall <fredrik.lingvall@gmail.com>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without calling an appropriate rule, AES/AES32 cards would announce a
theoretical channel count of 64 (HDSPM_MAX_CHANNELS), leading to the
already known bug:
[37422.640481] ------------[ cut here ]------------
[37422.640487] WARNING: at sound/pci/rme9652/hdspm.c:5449
snd_hdspm_ioctl+0x18f/0x202 [snd_hdspm]()
[37422.640489] Hardware name: PRIMERGY RX100 S6
[37422.640490] BUG? (info->channel >= hdspm->max_channels_in)
[37422.640492] Modules linked in: snd_hdspm snd_seq_midi ipmi_watchdog
ipmi_poweroff ipmi_si ipmi_devintf ipmi_msghandler i2c_i801 e1000e
snd_rawmidi power_meter [last unloaded: snd_hdspm]
[37422.640501] Pid: 22231, comm: jackd Tainted: G D W
2.6.36-gentoo-r5 #5
[37422.640502] Call Trace:
[37422.640508] [<ffffffff8103db3a>] warn_slowpath_common+0x80/0x98
[37422.640511] [<ffffffff8103dbe6>] warn_slowpath_fmt+0x41/0x43
[37422.640514] [<ffffffff81034306>] ? get_parent_ip+0x11/0x42
[37422.640518] [<ffffffffa0055763>] snd_hdspm_ioctl+0x18f/0x202
[snd_hdspm]
[37422.640522] [<ffffffff813fd626>] snd_pcm_channel_info+0x73/0x7c
[37422.640525] [<ffffffff814001e9>] snd_pcm_common_ioctl1+0x326/0xb01
[37422.640527] [<ffffffff81034306>] ? get_parent_ip+0x11/0x42
[37422.640531] [<ffffffff8105be6c>] ? __srcu_read_unlock+0x3b/0x59
[37422.640533] [<ffffffff81400bce>] snd_pcm_capture_ioctl1+0x20a/0x227
[37422.640537] [<ffffffff811e599c>] ? file_has_perm+0x90/0x9e
[37422.640540] [<ffffffff81400c15>] snd_pcm_capture_ioctl+0x2a/0x2e
[37422.640543] [<ffffffff810f2c69>] do_vfs_ioctl+0x404/0x453
[37422.640546] [<ffffffff810f2d09>] sys_ioctl+0x51/0x74
[37422.640549] [<ffffffff81002aab>] system_call_fastpath+0x16/0x1b
[37422.640552] ---[ end trace 0cd919cd68118082 ]---
We already have all the right values in place, we simply have to inform
the upper layers about this restriction.
Note that snd_hdspm_hw_rule_rate_out_channels and
snd_hdspm_hw_rule_rate_in_channels must not be called on AES32, because
the channel count is always 16, no matter of the samplerate in use.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only RayDAT and AIO provide sane buffer pointers that can be used with
HDSPM_BufferPositionMask, on all other cards, this would result in a
wrong HW pointer leading to xruns and these messages:
[260808.916788] BUG: pcmC0D0p:0, pos = 2976, buffer size = 1024, period size = 512
[260808.961124] BUG: pcmC0D0c:0, pos = 4944, buffer size = 1024, period size = 512
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As requested by Takashi and Jaroslav, these arrays should not be in the
header file.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Incorporate changes by Florian Faber into hdspm.c. Code taken from
http://wiki.linuxproaudio.org/index.php/Driver:hdspe
Heavily reworked to mostly comply with the coding standard (whitespace
fixes, line width, C++ style comments)
The code was tested and confirmed to be working on RME RayDAT.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SNDRV_HDSP_IOCTL_GET_CONFIG_INFO and
SNDRV_HDSP_IOCTL_GET_CONFIG_INFO ioctls in hdspm.c and hdsp.c allow
unprivileged users to read uninitialized kernel stack memory, because
several fields of the hdsp{m}_config_info structs declared on the stack
are not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use DEFINE_PCI_DEVICE_TABLE() to make PCI device ids go to
.devinit.rodata section, so they can be discarded in some cases,
and make them const.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace all tasklet_hi_schedule() callers with the normal
tasklet_schedule(). The former often causes troubles with
RT-kernels, and has actually no merit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The card->id (card text identification) can be changed at runtime.
It might be confusing to have old text identification in device name.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up SG-buffer helper functions and macros. Helpers take substream
as arguments now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
