Commit 88491d8(drivers/net: Kconfig & Makefile cleanup) causes a
regression that netconsole does not work if netconsole and network
device driver are build into kernel, because netconsole is linked
before network device driver.
Andrew Morton suggested to fix this with initcall ordering.
Fixes it by switching init_netconsole() to late_initcall.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function may currently fill one entry beyond the end of the
array it is given. It also doesn't return an error code in case
it does detect overflow.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using MLPPP, the maximum size of a fragment is incorrectly
calculated with an offset of -2.
This patch reverses the changes in the patch found here:
http://marc.info/?l=linux-netdev&m=123541324010539&w=2
The value of hdrlen includes the size of both the 2-byte PPP protocol
field and the 2- or 4-byte multilink header (2+4=6 for long sequence
numbers, 2+2=4 for short sequence numbers). Section 2 of RFC1661 says
that the MRU that is negotiated (i.e., the MTU of the sending system)
includes only the PPP payload but not the protocol field, thus the
correct MTU should be the link's MTU minus the multilink header (mtu -
(hdrlen-2)).
The incorrect calculation causes Linux to fragment packets to a size two
bytes smaller than the allowed MTU. While not technically illegal, this
behaviour confounds MRU-tuning to avoid PPP-layer fragmentation.
Signed-off-by: Henry Wong <henry@stuffedcow.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRETH GBIT core does not do checksum offloading for IP
segmentation. This patch adds a check in the xmit function to
determine if the stack has calculated the checksum for us.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling snmp6_alloc_dev fails, the snmp6 relevant memory
are freed by snmp6_alloc_dev. Calling in6_dev_finish_destroy
will free these memory twice.
Double free will lead that undefined behavior occurs.
Signed-off-by: Roy Li <rongqing.li@windriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o A performance drop was seen with firmware loaded
from flash. This workaround fixes it.
o Updated driver version to 4.0.77
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IP6_TNL_F_USE_ORIG_FWMARK to ip6_tunnel, so that ip6_tnl_xmit2()
makes a route lookup taking into account skb->fwmark and doesnt cache
lookup result.
This permits more flexibility in policies and firewall setups.
To setup such a tunnel, "fwmark inherit" option should be added to "ip
-f inet6 tunnel" command.
Reported-by: Anders Franzen <Anders.Franzen@ericsson.com>
CC: Hans Schillström <hans.schillstrom@ericsson.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a crash/BUG_ON in the clone ioctl due to insufficient reservation. We
need to reserve space for:
- adjusting the old extent (possibly splitting it)
- adding the new extent
- updating the inode
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Commit d1b08284 use new frag API but would leave f to be used
uninitialized, this patch fix it.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix broken sec=ntlmv2/i sec option (try #2)
Fix the conflict between rwpidforward and rw mount options
CIFS: Fix ERR_PTR dereference in cifs_get_root
cifs: fix possible memory corruption in CIFSFindNext
The enable function was using the global timeout variable for local operations.
This resulted in the value of the global variable being corrupted, thus
breaking the code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
On platforms with no iCRU support don't print two, (possibly conflicting),
"NMI occurred" messages when the firmware is unable to source the NMI.
Please note that one of the enhancements to the v1.3.0 hpwdt driver is to panic and allow
KDUMP to succeed even on NMIs that are unknown to the platform firmware.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the passed watchdog_device instead of the static global variable when
testing and setting the status in watchdog_ping, watchdog_start, and
watchdog_stop. Note that the callers of these functions are actually
passing the static global variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of using the multi_tx_table to map possible Tx queues to Tx rings
we can just do simple subtraction for the unlikely event that the Tx queue
provided exceeds the number of Tx rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since igb only uses advanced descriptors we might as well just use an IGB
specific define and drop the _ADV suffix for the descriptor declarations.
In addition this can be further reduced by assuming that it will be working
on pointers since that is normally how the Tx descriptors are handled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many of the function names in the hot path are carrying an extra "_adv"
suffix on the end of them to represent the fact that they are using
advanced descriptors instead of legacy descriptors. However since all igb
uses are advanced descriptors adding the extra suffix doesn't really add
any additional data. Since this is the case it is easiest to just drop the
suffix and save us from having to store the extra characters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to be a general cleanup and performance improvement
for clean_rx_irq. The previous patch should have updated the allocation so
that the rings can be treated as read-only within the clean_rx_irq
function. In addition I am re-ordering the operations such that several
goals are accomplished including reducing the overhead for packet
accounting, reducing the number of items on the stack, and improving
overall performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve performance by splitting the Tx and Rx
rings into 3 sections. The first is primarily a read only section
containing basic things like the indexes, a pointer to the dev and netdev
structures, and basic information. The second section contains the stats
and next_to_use and next_to_clean values. The third section is primarily
unused values that can just be placed at the end of the ring and are not
used in the hot path.
The adapter structure has several sections that are read in the hot path.
In order to improve performance there I am combining the frequent read
hot path items into a single cache line.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to streamline the Rx buffer allocation and cleanup.
This is accomplished by reducing the number of writes by only having the Rx
descriptor ring written by software during allocation, and it will only be
read during cleanup.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes support for single buffer mode from igb and makes the
driver function in packet split always. The advantage to doing this is
that we can reduce total memory allocation overhead significantly as we
will only need to allocate one 1K slab per packet and then make use of a
reusable half page instead of allocating a 2K slab per packet.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the max_frame_size in order account for an optional
VLAN tag. In order to support this we must also increase the
MAX_STD_JUMBO_FRAME_SIZE to account for the 4 extra bytes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the RXDCTL and TXDCTL configurations and optimizes RX
performance by allowing back write-backs on all hardware other than 82576.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix sec=ntlmv2/i authentication option during mount of Samba shares.
cifs client was coding ntlmv2 response incorrectly.
All that is needed in temp as specified in MS-NLMP seciton 3.3.2
"Define ComputeResponse(NegFlg, ResponseKeyNT, ResponseKeyLM,
CHALLENGE_MESSAGE.ServerChallenge, ClientChallenge, Time, ServerName)
as
Set temp to ConcatenationOf(Responserversion, HiResponserversion,
Z(6), Time, ClientChallenge, Z(4), ServerName, Z(4)"
is MsvAvNbDomainName.
For sec=ntlmsspi, build_av_pair is not used, a blob is plucked from
type 2 response sent by the server to use in authentication.
I tested sec=ntlmv2/i and sec=ntlmssp/i mount options against
Samba (3.6) and Windows - XP, 2003 Server and 7.
They all worked.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Both these options are started with "rw" - that's why the first one
isn't switched on even if it is specified. Fix this by adding a length
check for "rw" option check.
Cc: <stable@kernel.org>
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <sfrench@us.ibm.com>
move it to the beginning of the loop.
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The name_len variable in CIFSFindNext is a signed int that gets set to
the resume_name_len in the cifs_search_info. The resume_name_len however
is unsigned and for some infolevels is populated directly from a 32 bit
value sent by the server.
If the server sends a very large value for this, then that value could
look negative when converted to a signed int. That would make that
value pass the PATH_MAX check later in CIFSFindNext. The name_len would
then be used as a length value for a memcpy. It would then be treated
as unsigned again, and the memcpy scribbles over a ton of memory.
Fix this by making the name_len an unsigned value in CIFSFindNext.
Cc: <stable@kernel.org>
Reported-by: Darren Lavender <dcl@hppine99.gbr.hp.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86, iommu: Mark DMAR IRQ as non-threaded
genirq: Make irq_shutdown() symmetric vs. irq_startup again
* 'for-linus' of git://github.com/chrismason/linux:
Btrfs: only clear the need lookup flag after the dentry is setup
BTRFS: Fix lseek return value for error
Btrfs: don't change inode flag of the dest clone file
Btrfs: don't make a file partly checksummed through file clone
Btrfs: fix pages truncation in btrfs_ioctl_clone()
btrfs: fix d_off in the first dirent
When a xHC host is unable to handle isochronous transfer in the
interval, it reports a Missed Service Error event and skips some tds.
Currently xhci driver handles MSE event in the following ways:
1. When encounter a MSE event, set ep->skip flag, update event ring
dequeue pointer and return.
2. When encounter the next event on this ep, the driver will run the
do-while loop, fetch td from ep's td_list to find the td
corresponding to this event. All tds missed are marked as short
transfer(-EXDEV).
The do-while loop will end in two ways:
1. If the td pointed by the event trb is found;
2. If the ep ring's td_list is empty.
However, if a buggy HW reports some unpredicted event (for example, an
overrun event following a MSE event while the ep ring is actually not
empty), the driver will never find the td, and it will loop until the
td_list is empty.
Unfortunately, the spinlock is dropped when give back a urb in the
do-while loop. During the spinlock released period, the class driver
may still submit urbs and add tds to the td_list. This may cause
disaster, since the td_list will never be empty and the loop never ends,
and the system hangs.
To fix this, count the number of TDs on the ep ring before skipping TDs,
and quit the loop when skipped that number of tds. This guarantees the
do-while loop will end after certain number of cycles, and driver will
not be trapped in an infinite loop.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther
Point xHCI host controller will report a link state change with the
state set to "SS.Inactive". This causes the xHCI host controller to
issue a warm port reset, which doesn't finish before the USB core times
out while waiting for it to complete.
When the warm port reset does complete, and the xHC gives back a port
status change event, the xHCI driver kicks khubd. However, it fails to
set the bit indicating there is a change event for that port because the
logic in xhci-hub.c doesn't check for the warm port reset bit.
After that, the warm port status change bit is never cleared by the USB
core, and the xHC stops reporting port status change bits. (The xHCI
spec says it shouldn't report more port events until all change bits are
cleared.) This means any port changes when a new device is connected
will never be reported, and the port will seem "dead" until the xHCI
driver is unloaded and reloaded, or the computer is rebooted. Fix this
by making the xHCI driver set the port change bit when a warm port reset
change bit is set.
A better solution would be to make the USB core handle warm port reset
in differently, merging the current code with the standard port reset
code that does an incremental backoff on the timeout, and tries to
complete the port reset two more times before giving up. That more
complicated fix will be merged next window, and this fix will be
backported to stable.
This should be backported to kernels as old as 3.0, since that was the
first kernel with commit a11496ebf3 ("xHCI: warm reset support").
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build when CONFIG_ISA_DMA_API is enabled but
CONFIG_COMEDI_PCI[_DRIVERS] is not enabled.
Fixes these build errors:
drivers/staging/comedi/drivers/ni_labpc.c: In function 'labpc_ai_cmd':
drivers/staging/comedi/drivers/ni_labpc.c:1351: error: implicit declaration of function 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c: At top level:
drivers/staging/comedi/drivers/ni_labpc.c:1802: error: conflicting types for 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c:1351: note: previous implicit declaration of 'labpc_suggest_transfer_size' was here
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even with just the interface limited to admin, there really is little to
reason to give byte-per-byte counts for taskstats. So round it down to
something less intrusive.
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ok, this isn't optimal, since it means that 'iotop' needs admin
capabilities, and we may have to work on this some more. But at the
same time it is very much not acceptable to let anybody just read
anybody elses IO statistics quite at this level.
Use of the GENL_ADMIN_PERM suggested by Johannes Berg as an alternative
to checking the capabilities by hand.
Reported-by: Vasiliy Kulikov <segoon@openwall.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In ad-hoc mode, driver b43 does not issue beacons.
Signed-off-by: Manual Munz <freifunk@somakoma.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2)
drm/radeon/kms: fix typo in r100_blit_copy
drm/radeon: Unreference GEM object outside of spinlock in page flip error path.
drm/radeon: Don't read from CP ring write pointer registers.
drm/ttm: request zeroed system memory pages for new TT buffer objects
