Add support to iwlagn for off-channel TX. The
microcode API for this is a bit strange in that
it uses a hacked-up scan command, so the scan
code needs to change quite a bit to accomodate
that and be able to send it out.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put generic rx_handlers (except iwlagn_rx_reply_compressed_ba) to
iwl-rx.c . Make functions static and change prefix from iwlagn_ to
iwl_ . Beautify iwl_setup_rx_handlers and do some other minor coding
style changes.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The temperature reported by 'cat /sys/class/net/wlan?/device/temperature'
is incorrect for devices with BT capability. Report the value from the
correct statistics structure. Tested with 130, 100, 6205 and 5300.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Add module ack_check, and plcp_check parameters. Ack_check is disabled
by default since is proved that check ack health can cause troubles.
Plcp_check is enabled by default.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag isn't very descriptive -- the intention
is that the driver provides a TSF timestamp at
the beginning of the MPDU -- make that clearer
by renaming the flag to RX_FLAG_MACTIME_MPDU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code, and the places that set the variable
is_internal_short_scan and the vif pointers are
all protected by the mutex, there's no point in
locking the spinlock here as well (any more).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
During the period of BT coex changes, REPLY_BT_COEX_SCO host command
is no longer needed to support SCO/eSCO type of traffic. delete it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to
IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping
channel numbers in the 2GHz and 5GHz band we can't map from channel to
frequency without knowing the band. This is no problem as in most contexts we
know the band. In places where we don't know the band (and WEXT compatibility)
we assume the 2GHz band for channels below 14.
This patch does not implement all channel to frequency mappings defined in
802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz
channels as well as 802.11y channels have been omitted.
The following drivers have been updated to reflect the API changes:
iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx.
The drivers have been compile-tested only.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Brian Prodoehl <bprodoehl@gmail.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to implement waiting for notifications,
add a structure that captures the information,
and a list of such structures that will be
traversed when a command is received from the
ucode.
Use sparse checking to make sure calls to the
prepare/wait/cancel functions are always nested
correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Looks that we do not set correctly antennas when scanning
on 5Ghz band and when bluetooth is enabled, because
priv->cfg->scan_tx_antennas[band] is only defined for
IEEE80211_BAND_2GHZ.
To fix we check band before limiting antennas to first one.
This allow to remove hard coded cfg->scan_tx_antennas[band].
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.
However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This patch replace monitor/recover timer by watchdog based on time
stamp. New code allow to discover hangs more precisely.
Timeout values are currently doubled monitoring period values of
previous timer. This have to be tuned based of firmware timing
capabilities.
Tested on 3945, 4965, 5300, 6300.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the BT PSPoll flag when fill PM command to uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
48644 57 12120 60821 ed95 drivers/net/wireless/b43/phy_n.o.new
48661 57 12120 60838 eda6 drivers/net/wireless/b43/phy_n.o.old
37906 86 7904 45896 b348 drivers/net/wireless/iwlwifi/iwl-agn-lib.o.new
37937 86 7904 45927 b367 drivers/net/wireless/iwlwifi/iwl-agn-lib.o.old
37781 523 6752 45056 b000 drivers/net/wireless/iwlwifi/iwl-3945.o.new
37781 523 6752 45056 b000 drivers/net/wireless/iwlwifi/iwl-3945.o.old
Changed b43_nphy_write_clip_detection to take a const u16 *
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, we used the swq_id's mechanism
to have AC and HW queue different only for
aggregation queues. To be able to fix a bug
with iPAN simply always build the swq_id as
ac | (hwq << 2) and remove the flag bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of passing the txq->swq_id, pass the
txq struct directly to make sure that in the
future nobody will pass an invalid number.
Only three places actually change from using
the txq_id or the skb's queue_mapping to now
using txq->swq_id as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Even if this check were to happen, using the
txq_id here (which is a HW queue) would lead
to confusion in mac80211. Luckily, it doesn't
seem like this can ever happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Use dynamic aggregation threshold if bt traffic load is high
to reduce the impact on aggregated frame.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For 6000 series devices and up, enable automatic update MAC's register
for better power usage in PSP mode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building 4965 without 5000+ there were a
lot of build errors due to functions being used
that weren't even compiled in. To fix this move
some code around and only compile the HCMD code
for 5000+ series as it's not used for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While BT is on and doing iscan and/or pscan, BT is in listen
mode which will impact WiFi throughput, we need to
enable dynamic smps in order to improve the rx throughput.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid sending commands to firmware (including commit_rxon) when scan
is pending and we are calling iwlagn_bt_traffic_change_work simultaneously.
Also comment some innocent race conditions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 5xxx and 6xxx change to send tx_power_cmd command synchronously,
to do not start other commands when setting tx power is pending.
We currently do the same for 4956 and 3945.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add WARN_ONCE when scanning is pending. Use STATUS_SCAN_HW bit since we
can have scan canceled or completed but STATUS_SCANNING bit still set.
v1 -> v2: replace EIO to EAGAIN
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two passive 2.4 GHz channels: 12 and 13.
If you have a hidden SSID on those, you will not
be able to connect to it because we don't send out
probe requests there. We can allow this by using
the firmware's probe-after-rx functionality on
those channels as well.
This fixes
https://bugzilla.kernel.org/show_bug.cgi?id=16462
Reported-by: Daniel J Blueman <daniel.blueman@gmail.com>
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The recent scanning code shuffle accidentally
moved the SCAN_HW bit setting _after_ the PAN
parameters are modified, which means that they
don't take the scan into account -- fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The set_pwr_src operation is only ever used from
within the same sub-driver that it is declared
in, so it can just be called directly instead of
being an operation. Also, it is never called to
set the power source to V_aux, so change the two
functions accordingly (but keep the V_aux code
for documentation purposes in a comment).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The iwl_dump_fh function is only used
by the agn module, so it can be there
instead of being exported by the core.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The iwl_dump_csr function is only used
within the agn module, so it can be
moved there instead of being exported
by the core.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The iwl_toggle_tx_ant function is only used
by agn code, so it can be moved into the
agn module instead of being exported from
the core.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
By duplicating a little bit of code between 3945
and agn, we can move a lot of code into an agn
specific station management file and thus reduce
the amount of code in core that is dead to 3945.
before:
text data bss dec hex filename
212886 3872 96 216854 34f16 iwlcore.ko
620542 10448 304 631294 9a1fe iwlagn.ko
314013 3264 196 317473 4d821 iwl3945.ko
after:
text data bss dec hex filename
202857 3872 92 206821 327e5 iwlcore.ko
629102 10448 308 639858 9c372 iwlagn.ko
314240 3264 196 317700 4d904 iwl3945.ko
delta:
-10029 iwlcore.ko
8560 iwlagn.ko
227 iwl3945.ko
so it's a net win even if you have both loaded,
likely because a lot of EXPORT_SYMBOLs go away.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The core module doesn't need to carry around
the code for chain settings that is used for
HT drivers (agn) only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The different drivers need to do different things
after a scan, so create a post_scan hook to allow
them to do this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
move paramater definitions to a device paramater structure only
leaving the device name, which antennas are used and what firmware
file to use in the iwl_cfg structure. this will not completely
remove the redundancies but greatly reduce them for devices that
only vary by name or antennas. the parameters that are more
likely to change within a given device family are left in iwl_cfg.
also separate bt param structure added to help reduce more.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When uCode completed the aggregated frames transmission attempt,
it will send tx command response with aggregated frame status.
Keep track of the failure counter which help indicate any transmission
error condition.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For aggregated frames with block ack, different status flag
will be used as part of tx command response.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If uCode fail to transmit frame, it will send reply tx back
to driver with failure status; keep the counters of each failure
cases for debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Rather than duplicating all the checks and even
in case of errors accepting the scan request
from mac80211, we can push the checks to the
caller and in all error cases reject the scan
request right away (rather than accepting and
then saying it was aborted).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
