Currently we wait only until the PGC inverts the isolation setting
before disabling the peripheral clocks. This doesn't ensure that the
reset is properly propagated through the peripheral devices in the
power domain.
Wait until the PGC signals that the power up request is done and
wait a bit for resets to propagate before disabling the clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The soc-imx8.c driver is actually for i.MX8M family, so rename it
to soc-imx8m.c.
Use CONFIG_SOC_IMX8M as build gate, not CONFIG_ARCH_MXC, to control
whether build this driver, also make it possible for compile test.
Default set it to y for ARCH_MXC && ARM64
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use PDR helper functions to track the protection domains that the apr
services are dependent upon on SDM845 SoC, specifically the "avs/audio"
service running on ADSP Q6.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200312120842.21991-4-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Qualcomm SoCs (starting with MSM8998) allow for multiple protection domains
to run on the same Q6 sub-system. This allows for services like ATH10K WLAN
FW to have their own separate address space and crash/recover without
disrupting the modem and other PDs running on the same sub-system. The PDR
helpers introduces an abstraction that allows for tracking/controlling the
life cycle of protection domains running on various Q6 sub-systems.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200312120842.21991-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Avoid using a mixture of tabs and spaces within tables to make them
easier to read and more consistently formatted.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Extend the Tegra194 IO pad table with additional information such as pin
names and 1.8/3.3 V settings to allow a table of voltage control pins to
generated from it. This is similar to what's done for older chips and is
needed to support high-speed modes for SDHCI where switching the pins to
1.8V or 3.3V is necessary.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra PMC has blink control to output 32 kHz clock out to Tegra blink
pin. Blink pad DPD state and enable controls are part of Tegra PMC
register space.
Currently Tegra clock driver registers blink control by passing PMC
address and register offset to clk_register_gate which performs direct
PMC access during clk_ops and with this when PMC is in secure mode, any
access from non-secure world does not go through.
This patch adds blink control registration to the Tegra PMC driver using
PMC specific clock gate operations that use tegra_pmc_readl() and
tegra_pmc_writel() to support both secure mode and non-secure
mode PMC register access.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra PMC has clk_out_1, clk_out_2, and clk_out_3 clocks and currently
these PMC clocks are registered by Tegra clock driver with each clock as
separate mux and gate clocks using clk_register_mux and clk_register_gate
by passing PMC base address and register offsets and PMC programming for
these clocks happens through direct PMC access by the clock driver.
With this, when PMC is in secure mode any direct PMC access from the
non-secure world does not go through and these clocks will not be
functional.
This patch adds these PMC clocks registration to pmc driver with PMC as
a clock provider and registers each clock as single clock.
clk_ops callback implementations for these clocks uses tegra_pmc_readl and
tegra_pmc_writel which supports PMC programming in both secure mode and
non-secure mode.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is a single character that we're printing out. Use seq_putc() for
that to simplify the code.
Cc: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200309185123.65265-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This tracepoint is hit now that we call into the rpmh code from the cpu
idle path. Let's move this to be an rcuidle tracepoint so that we avoid
the RCU idle splat below
=============================
WARNING: suspicious RCU usage
5.4.10 #68 Tainted: G S
-----------------------------
drivers/soc/qcom/trace-rpmh.h:72 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 2, debug_locks = 1
RCU used illegally from extended quiescent state!
5 locks held by swapper/2/0:
#0: ffffff81745d6ee8 (&(&genpd->slock)->rlock){+.+.}, at: genpd_lock_spin+0x1c/0x2c
#1: ffffff81745da6e8 (&(&genpd->slock)->rlock/1){....}, at: genpd_lock_nested_spin+0x24/0x34
#2: ffffff8174f2ca20 (&(&genpd->slock)->rlock/2){....}, at: genpd_lock_nested_spin+0x24/0x34
#3: ffffff8174f2c300 (&(&drv->client.cache_lock)->rlock){....}, at: rpmh_flush+0x48/0x24c
#4: ffffff8174f2c150 (&(&tcs->lock)->rlock){+.+.}, at: rpmh_rsc_write_ctrl_data+0x74/0x270
stack backtrace:
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G S 5.4.10 #68
Call trace:
dump_backtrace+0x0/0x174
show_stack+0x20/0x2c
dump_stack+0xc8/0x124
lockdep_rcu_suspicious+0xe4/0x104
__tcs_buffer_write+0x230/0x2d0
rpmh_rsc_write_ctrl_data+0x210/0x270
rpmh_flush+0x84/0x24c
rpmh_domain_power_off+0x78/0x98
_genpd_power_off+0x40/0xc0
genpd_power_off+0x168/0x208
genpd_power_off+0x1e0/0x208
genpd_power_off+0x1e0/0x208
genpd_runtime_suspend+0x1ac/0x220
__rpm_callback+0x70/0xfc
rpm_callback+0x34/0x8c
rpm_suspend+0x218/0x4a4
__pm_runtime_suspend+0x88/0xac
psci_enter_domain_idle_state+0x3c/0xb4
cpuidle_enter_state+0xb8/0x284
cpuidle_enter+0x38/0x4c
call_cpuidle+0x3c/0x68
do_idle+0x194/0x260
cpu_startup_entry+0x24/0x28
secondary_start_kernel+0x150/0x15c
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Fixes: a65a397f24 ("cpuidle: psci: Add support for PM domains by using genpd")
Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200115013751.249588-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
QMI helpers are not always used by Qualcomm platforms. One of the
exceptions is the external modems available in near future.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200220095854.4804-17-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When MESON_SECURE_PM_DOMAINS & !MESON_SM, there will be compile failure:
.../meson-secure-pwrc.o: In function `meson_secure_pwrc_on':
.../meson-secure-pwrc.c:76: undefined reference to `meson_sm_call'
Fix this by adding depends on MESON_SM for MESON_SECURE_PM_DOMAINS.
Fixes: b3dde5013e ("soc: amlogic: Add support for Secure power domains controller")
Reported-by: Stephen Rothwell<sfr@canb.auug.org.au>
Reported-by: patchwork-bot+linux-amlogic<patchwork-bot+linux-amlogic@kernel.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Stephen Rothwell<sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/1581955933-69832-1-git-send-email-jianxin.pan@amlogic.com
Some cpuidle C-states supported on am335x and am437x, like C1 on am335x,
require the use of the wkup_m3_ipc driver, and all C-states beyond C0 on
both platforms require the use of the SRAM sleep code.
Pass am33xx_do_sram_idle as the idle function to the platform pm core to
be used by the cpuidle-arm driver when entering cpuidle states.
am33xx_do_sram_idle will detect when the wkup_m3 is needed and ping it
if necessary before calling the final cpu_suspend op which will execute
the SRAM code to put the cpu into idle.
Finally, use the begin_suspend and finish_suspend platform ops to be
called at the beginning and end of suspend path to allow use of
cpu_idle_poll_ctrl.
This prevents races between cpuidle and suspend paths trying to
communicate with the wkup_m3, as during suspend we only want it
configured for entry to suspend.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for am335x and am437x to properly enter deeper c-states in
cpuidle they must always call into the sleep33/43xx suspend code and
also sometimes invoke the wkup_m3_ipc driver. These are both controlled
by the pm33xx module so we must provide a method for the platform code
to call back into the module when it is available as the core cpuidle
ops that are invoked by the cpuidle-arm driver must remain as built in.
Extend the init platform op to take an idle function as an argument so
that we can use this to call into the pm33xx module for c-states that
need it. Also add a deinit op so we can unregister this idle function
from the PM core when the pm33xx module gets unloaded.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl5TuEMUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4a+Qf9Enb2G47LTMeYH5JYhm2anDQ4lz+8
Og1bcGPYKilDhc4YzpAIhRnOTLa9TietZSS0tyNFk37GDfKRjn9gxXDRbI+4lrJc
UOSLpWCB4BnzKc+FoCHC37jkdkMD3V2E5MmFHtYkGYmH0DAi8cLmGebmgGujd0GJ
lx2/5EbxKoJxeA2i79H5OAPBhglJsEnPTSulZ+jUdLzJfBlRBIQBc3oPcwnRIibr
VUbLc4Gkb2kTe6NwdQTjqI+4BTHv7/4m+twOojO5Z8QBH4X+3bkLnLiylhuqHBeR
cDXGL7sHkekZhDQ3OwIMiT/5cc8SxplqAl6QMm8+/9gq7KfAucy8Psokow==
=dg69
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.6:
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
* tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx-scu: Align imx sc msg structs to 4
firmware: imx: Align imx_sc_msg_req_cpu_start to 4
firmware: imx: scu-pd: Align imx sc msg structs to 4
firmware: imx: misc: Align imx sc msg structs to 4
firmware: imx: scu: Ensure sequential TX
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
arm64: dts: imx8qxp-mek: Remove unexisting Ethernet PHY
ARM: dts: imx6dl-colibri-eval-v3: fix sram compatible properties
ARM: dts: ls1021a: Restore MDIO compatible to gianfar
ARM: dts: imx7d: fix opp-supported-hw
ARM: imx: build v7_cpu_resume() unconditionally
ARM: dts: imx6: phycore-som: fix emmc supply
Link: https://lore.kernel.org/r/20200224120334.GH27688@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: 73feb4d0f8 ("soc: imx-scu: Add SoC UID(unique identifier) support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pointer p is currently being dereferenced before it is null
checked on a memory allocation failure check. Fix this by
checking if p is null before dereferencing it.
Addresses-Coverity: ("Dereference before null check")
Fixes: 3b2abda7d2 ("soc: fsl: dpio: Replace QMAN array mode with ring mode enqueue")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Replace the final user of CONFIG_ARCH_R8A7795 by CONFIG_ARCH_R8A77950 ||
CONFIG_ARCH_R8A77951, and remove the now unused CONFIG_ARCH_R8A7795
symbol definition.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218112449.5723-1-geert+renesas@glider.be
This change of algorithm will enable faster bulk enqueue.
This will greatly benefit XDP bulk enqueue.
Signed-off-by: Youri Querry <youri.querry_1@nxp.com>
Acked-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
We are making the access decision in the initialization and
setting the function pointers accordingly.
Signed-off-by: Youri Querry <youri.querry_1@nxp.com>
Acked-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Update of QMAN the interface to enqueue frame. We now support multiple
enqueue (qbman_swp_enqueue_multiple) and multiple enqueue with
a table of descriptor (qbman_swp_enqueue_multiple_desc).
Signed-off-by: Youri Querry <youri.querry_1@nxp.com>
Acked-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
This patch corrects the SPDX License Identifier style in
header file related to Renesas Soc driver support.
It assigns explicit block comment to the SPDX License Identifier.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200118124856.GA3421@nishad
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
MT6359 is a new power management IC and it is used for
MT6779 SoCs. To define mt6359_regs for pmic register mapping
and pmic_mt6359 for accessing register.
Signed-off-by: Argus Lin <argus.lin@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT6779 is a highly integrated SoCs, it uses PMIC_MT6359 for
power management. This patch adds pwrap master driver to
access PMIC_MT6359.
Signed-off-by: Argus Lin <argus.lin@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the Amlogic Secure Power controller. In A1/C1 series, power
control registers are in secure domain, and should be accessed by smc.
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/1579087831-94965-4-git-send-email-jianxin.pan@amlogic.com
Mediatek CMDQ driver have a mechanism to do TXDONE_BY_ACK,
so we should set knows_txdone.
Fixes:576f1b4bc802 ("soc: mediatek: Add Mediatek CMDQ helper")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In some device memory used by msm_qmp, there can be an early ack of a
write to memory succeeding. This may cause the outgoing interrupt to be
triggered before the msgram reflects the write.
Add a readback to ensure the data is flushed to device memory before
triggering the ipc interrupt.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Link: https://lore.kernel.org/r/1579681454-1229-1-git-send-email-aneela@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
During the probe the task is waiting in TASK_UNINTERRUPTIBLE state which
cannot be woken-up by wake_up_interruptible_all() function.
Use wake_up_all() to wake-up both TASK_UNINTERRUPTIBLE and
TASK_INTERRUPTIBLE state tasks.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Link: https://lore.kernel.org/r/1579681417-1155-1-git-send-email-aneela@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This header is included indirectly on arm/arm64 but not on x86 so
CONFIG_COMPILE_TEST breaks. Fix by including <linux/sizes.h> directly.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
rpmh_flush() was exported with the idea that an external entity
operation during CPU idle would know when to flush the sleep and wake
TCS. Since, this is not the case when defining a power domain for the
RSC. Remove the function export and instead allow the function to be
called internally.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1580736940-6985-3-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Device argument matches with dev variable declared in RPMH message.
Compiler reports error when the argument is NULL since the argument
matches the name of the property. Rename dev argument to device to
fix this.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1580736940-6985-2-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If only Tegra194 support is enabled, the tegra30_fuse_read() and
tegra30_fuse_init() function are not declared and cause a build failure.
Add Tegra194 to the preprocessor guard to make sure these functions are
available for Tegra194-only builds as well.
Link: https://lore.kernel.org/r/20200203143114.3967295-1-thierry.reding@gmail.com
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
SH-Mobile AG5 and R-Car H1 SoCs are based on the Cortex-A9 MPCore, which
includes a global timer.
Enable the ARM global timer on these SoCs, which will be used for:
- the scheduler clock, improving scheduler accuracy from 10 ms to 3 or
4 ns,
- delay loops, allowing removal of calls to shmobile_init_delay() from
the corresponding machine vectors.
Note that when using an old DTB lacking the global timer, the kernel
will still work. However, loops-per-jiffies will no longer be preset,
and the delay loop will need to be calibrated during boot.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191211135222.26770-5-geert+renesas@glider.be
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60.
-----BEGIN PGP SIGNATURE-----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=fIjZ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: OMAP2+: Fix undefined reference to omap_secure_init
ARM: s3c64xx: Drop unneeded select of TIMER_OF
ARM: exynos: Drop unneeded select of MIGHT_HAVE_CACHE_L2X0
ARM: s3c24xx: Switch to atomic pwm API in rx1950
ARM: OMAP2+: sleep43xx: Call secure suspend/resume handlers
ARM: OMAP2+: Use ARM SMC Calling Convention when OP-TEE is available
ARM: OMAP2+: Introduce check for OP-TEE in omap_secure_init()
ARM: OMAP2+: Add omap_secure_init callback hook for secure initialization
ARM: at91: Documentation: add sam9x60 product and datasheet
ARM: at91: pm: use of_device_id array to find the proper shdwc node
ARM: at91: pm: use SAM9X60 PMC's compatible
ARM: imx: only select ARM_ERRATA_814220 for ARMv7-A
ARM: zynq: use physical cpuid in zynq_slcr_cpu_stop/start
ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume
ARM: tegra: Modify reshift divider during LP1
ARM: tegra: Enable PLLP bypass during Tegra124 LP1
ARM: samsung: Rename Samsung and Exynos to lowercase
ARM: exynos: Correct the help text for platform Kconfig option
ARM: bcm: Select ARM_AMBA for ARCH_BRCMSTB
ARM: brcmstb: Add debug UART entry for 7216
...
- Support mremap() for the VDSO, primarily to allow CRIU to restore the
VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement of
the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs by
running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to
take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXjRnpxYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDdNYoA/3ZhgKX1L/hwvkPKwu7FxbL41pjB
WAm8IYDaxPvgxkcSAP9FNNepHK+oBPM8I2e3DvDvmcuYjumztdikzYbJ5HuMBA==
=MV2S
-----END PGP SIGNATURE-----
Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS changes from Paul Burton:
"Nothing too big or scary in here:
- Support mremap() for the VDSO, primarily to allow CRIU to restore
the VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement
of the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs
by running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style
MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them
to take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups"
* tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits)
MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel
MIPS: Loongson64: Disable exec hazard
MIPS: Loongson64: Bump ISA level to MIPSR2
MIPS: Make DIEI support as a config option
MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too"
MIPS: asm: local: add barriers for Loongson
MIPS: Loongson64: Select mac2008 only feature
MIPS: Add MAC2008 Support
Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel"
MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again)
MIPS: make CPU_HAS_LOAD_STORE_LR opt-out
MIPS: generic: don't unconditionally select PINCTRL
MIPS: don't explicitly select LIBFDT in Kconfig
MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts
MIPS: SGI-IP30: Check for valid pointer before using it
MIPS: syscalls: fix indentation of the 'SYSNR' message
MIPS: boot: fix typo in 'vmlinux.lzma.its' target
MIPS: fix indentation of the 'RELOCS' message
dt-bindings: Document loongson vendor-prefix
MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi.
...
uapi:
- dma-buf heaps added (and fixed)
- command line add support for panel oreientation
- command line allow overriding penguin count
drm:
- mipi dsi definition updates
- lockdep annotations for dma_resv
- remove dma-buf kmap/kunmap support
- constify fb_ops in all fbdev drivers
- MST fix for daisy chained hotplug-
- CTA-861-G modes with VIC >= 193 added
- fix drm_panel_of_backlight export
- LVDS decoder support
- more device based logging support
- scanline alighment for dumb buffers
- MST DSC helpers
scheduler:
- documentation fixes
- job distribution improvements
panel:
- Logic PD type 28 panel support
- Jimax8729d MIPI-DSI
- igenic JZ4770
- generic DSI devicetree bindings
- sony acx424AKP panel
- Leadtek LTK500HD1829
- xinpeng XPP055C272
- AUO B116XAK01
- GiantPlus GPM940B0
- BOE NV140FHM-N49
- Satoz SAT050AT40H12R2
- Sharp LS020B1DD01D panels.
ttm:
- use blocking WW lock
i915:
- hw/uapi state separation
- Lock annotation improvements
- selftest improvements
- ICL/TGL DSI VDSC support
- VBT parsing improvments
- Display refactoring
- DSI updates + fixes
- HDCP 2.2 for CFL
- CML PCI ID fixes
- GLK+ fbc fix
- PSR fixes
- GEN/GT refactor improvments
- DP MST fixes
- switch context id alloc to xarray
- workaround updates
- LMEM debugfs support
- tiled monitor fixes
- ICL+ clock gating programming removed
- DP MST disable sequence fixed
- LMEM discontiguous object maps
- prefaulting for discontiguous objects
- use LMEM for dumb buffers if possible
- add LMEM mmap support
amdgpu:
- enable sync object timelines for vulkan
- MST atomic routines
- enable MST DSC support
- add DMCUB display microengine support
- DC OEM i2c support
- Renoir DC fixes
- Initial HDCP 2.x support
- BACO support for Arcturus
- Use BACO for runtime PM power save
- gfxoff on navi10
- gfx10 golden updates and fixes
- DCN support on POWER
- GFXOFF for raven1 refresh
- MM engine idle handlers cleanup
- 10bpc EDP panel fixes
- renoir watermark fixes
- SR-IOV fixes
- Arcturus VCN fixes
- GDDR6 training fixes
- freesync fixes
- Pollock support
amdkfd:
- unify more codepath with amdgpu
- use KIQ to setup HIQ rather than MMIO
radeon:
- fix vma fault handler race
- PPC DMA fix
- register check fixes for r100/r200
nouveau:
- mmap_sem vs dma_resv fix
- rewrite the ACR secure boot code for Turing
- TU10x graphics engine support (TU11x pending)
- Page kind mapping for turing
- 10-bit LUT support
- GP10B Tegra fixes
- HD audio regression fix
hisilicon/hibmc:
- use generic fbdev code and helpers
rockchip:
- dsi/px30 support
virtio:
- fb damage support
- static some functions
vc4:
- use dma_resv lock wrappers
msm:
- use dma_resv lock wrappers
- sc7180 display + DSI support
- a618 support
- UBWC support improvements
vmwgfx:
- updates + new logging uapi
exynos:
- enable/disable callback cleanups
etnaviv:
- use dma_resv lock wrappers
atmel-hlcdc:
- clock fixes
mediatek:
- cmdq support
- non-smooth cursor fixes
- ctm property support
sun4i:
- suspend support
- A64 mipi dsi support
rcar-du:
- Color management module support
- LVDS encoder dual-link support
- R8A77980 support
analogic:
- add support for an6345
ast:
- atomic modeset support
- primary plane garbage fix
arcgpu:
- fixes for fourcc handling
tegra:
- minor fixes and improvments
mcde:
- vblank support
meson:
- OSD1 plane AFBC commit
gma500:
- add pageflip support
- reomve global drm_dev
komeda:
- tweak debugfs output
- d32 support
- runtime PM suppotr
udl:
- use generic shmem helpers
- cleanup and fixes
-----BEGIN PGP SIGNATURE-----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=oFrI
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Davbe Airlie:
"This is the main pull request for graphics for 5.6. Usual selection of
changes all over.
I've got one outstanding vmwgfx pull that touches mm so kept it
separate until after all of this lands. I'll try and get it to you
soon after this, but it might be early next week (nothing wrong with
code, just my schedule is messy)
This also hits a lot of fbdev drivers with some cleanups.
Other notables:
- vulkan timeline semaphore support added to syncobjs
- nouveau turing secureboot/graphics support
- Displayport MST display stream compression support
Detailed summary:
uapi:
- dma-buf heaps added (and fixed)
- command line add support for panel oreientation
- command line allow overriding penguin count
drm:
- mipi dsi definition updates
- lockdep annotations for dma_resv
- remove dma-buf kmap/kunmap support
- constify fb_ops in all fbdev drivers
- MST fix for daisy chained hotplug-
- CTA-861-G modes with VIC >= 193 added
- fix drm_panel_of_backlight export
- LVDS decoder support
- more device based logging support
- scanline alighment for dumb buffers
- MST DSC helpers
scheduler:
- documentation fixes
- job distribution improvements
panel:
- Logic PD type 28 panel support
- Jimax8729d MIPI-DSI
- igenic JZ4770
- generic DSI devicetree bindings
- sony acx424AKP panel
- Leadtek LTK500HD1829
- xinpeng XPP055C272
- AUO B116XAK01
- GiantPlus GPM940B0
- BOE NV140FHM-N49
- Satoz SAT050AT40H12R2
- Sharp LS020B1DD01D panels.
ttm:
- use blocking WW lock
i915:
- hw/uapi state separation
- Lock annotation improvements
- selftest improvements
- ICL/TGL DSI VDSC support
- VBT parsing improvments
- Display refactoring
- DSI updates + fixes
- HDCP 2.2 for CFL
- CML PCI ID fixes
- GLK+ fbc fix
- PSR fixes
- GEN/GT refactor improvments
- DP MST fixes
- switch context id alloc to xarray
- workaround updates
- LMEM debugfs support
- tiled monitor fixes
- ICL+ clock gating programming removed
- DP MST disable sequence fixed
- LMEM discontiguous object maps
- prefaulting for discontiguous objects
- use LMEM for dumb buffers if possible
- add LMEM mmap support
amdgpu:
- enable sync object timelines for vulkan
- MST atomic routines
- enable MST DSC support
- add DMCUB display microengine support
- DC OEM i2c support
- Renoir DC fixes
- Initial HDCP 2.x support
- BACO support for Arcturus
- Use BACO for runtime PM power save
- gfxoff on navi10
- gfx10 golden updates and fixes
- DCN support on POWER
- GFXOFF for raven1 refresh
- MM engine idle handlers cleanup
- 10bpc EDP panel fixes
- renoir watermark fixes
- SR-IOV fixes
- Arcturus VCN fixes
- GDDR6 training fixes
- freesync fixes
- Pollock support
amdkfd:
- unify more codepath with amdgpu
- use KIQ to setup HIQ rather than MMIO
radeon:
- fix vma fault handler race
- PPC DMA fix
- register check fixes for r100/r200
nouveau:
- mmap_sem vs dma_resv fix
- rewrite the ACR secure boot code for Turing
- TU10x graphics engine support (TU11x pending)
- Page kind mapping for turing
- 10-bit LUT support
- GP10B Tegra fixes
- HD audio regression fix
hisilicon/hibmc:
- use generic fbdev code and helpers
rockchip:
- dsi/px30 support
virtio:
- fb damage support
- static some functions
vc4:
- use dma_resv lock wrappers
msm:
- use dma_resv lock wrappers
- sc7180 display + DSI support
- a618 support
- UBWC support improvements
vmwgfx:
- updates + new logging uapi
exynos:
- enable/disable callback cleanups
etnaviv:
- use dma_resv lock wrappers
atmel-hlcdc:
- clock fixes
mediatek:
- cmdq support
- non-smooth cursor fixes
- ctm property support
sun4i:
- suspend support
- A64 mipi dsi support
rcar-du:
- Color management module support
- LVDS encoder dual-link support
- R8A77980 support
analogic:
- add support for an6345
ast:
- atomic modeset support
- primary plane garbage fix
arcgpu:
- fixes for fourcc handling
tegra:
- minor fixes and improvments
mcde:
- vblank support
meson:
- OSD1 plane AFBC commit
gma500:
- add pageflip support
- reomve global drm_dev
komeda:
- tweak debugfs output
- d32 support
- runtime PM suppotr
udl:
- use generic shmem helpers
- cleanup and fixes"
* tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm: (1998 commits)
drm/nouveau/fb/gp102-: allow module to load even when scrubber binary is missing
drm/nouveau/acr: return error when registering LSF if ACR not supported
drm/nouveau/disp/gv100-: not all channel types support reporting error codes
drm/nouveau/disp/nv50-: prevent oops when no channel method map provided
drm/nouveau: support synchronous pushbuf submission
drm/nouveau: signal pending fences when channel has been killed
drm/nouveau: reject attempts to submit to dead channels
drm/nouveau: zero vma pointer even if we only unreference it rather than free
drm/nouveau: Add HD-audio component notifier support
drm/nouveau: fix build error without CONFIG_IOMMU_API
drm/nouveau/kms/nv04: remove set but not used variable 'width'
drm/nouveau/kms/nv50: remove set but not unused variable 'nv_connector'
drm/nouveau/mmu: fix comptag memory leak
drm/nouveau/gr/gp10b: Use gp100_grctx and gp100_gr_zbc
drm/nouveau/pmu/gm20b,gp10b: Fix Falcon bootstrapping
drm/exynos: Rename Exynos to lowercase
drm/exynos: change callback names
drm/mst: Don't do atomic checks over disabled managers
drm/amdgpu: add the lost mutex_init back
drm/amd/display: skip opp blank or unblank if test pattern enabled
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
- Core:
- Support for dynamic channels
- Removal of various slave wrappers
- Make few slave request APIs as private to dmaengine
- Symlinks between channels and slaves
- Support for hotplug of controllers
- Support for metadata_ops for dma_async_tx_descriptor
- Reporting DMA cached data amount
- Virtual dma channel locking updates
- New drivers/device/feature support support:
- Driver for Intel data accelerators
- Driver for TI K3 UDMA
- Driver for PLX DMA engine
- Driver for hisilicon Kunpeng DMA engine
- Support for eDMA support for QorIQ LS1028A in fsl edma driver
- Support for cyclic dma in sun4i driver
- Support for X1830 in JZ4780 driver
-----BEGIN PGP SIGNATURE-----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=mv1v
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have a bunch of core changes to support dynamic channels,
hotplug of controllers, new apis for metadata ops etc along with new
drivers for Intel data accelerators, TI K3 UDMA, PLX DMA engine and
hisilicon Kunpeng DMA engine. Also usual assorted updates to drivers.
Core:
- Support for dynamic channels
- Removal of various slave wrappers
- Make few slave request APIs as private to dmaengine
- Symlinks between channels and slaves
- Support for hotplug of controllers
- Support for metadata_ops for dma_async_tx_descriptor
- Reporting DMA cached data amount
- Virtual dma channel locking updates
New drivers/device/feature support support:
- Driver for Intel data accelerators
- Driver for TI K3 UDMA
- Driver for PLX DMA engine
- Driver for hisilicon Kunpeng DMA engine
- Support for eDMA support for QorIQ LS1028A in fsl edma driver
- Support for cyclic dma in sun4i driver
- Support for X1830 in JZ4780 driver"
* tag 'dmaengine-5.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (62 commits)
dmaengine: Create symlinks between DMA channels and slaves
dmaengine: hisilicon: Add Kunpeng DMA engine support
dmaengine: idxd: add char driver to expose submission portal to userland
dmaengine: idxd: connect idxd to dmaengine subsystem
dmaengine: idxd: add descriptor manipulation routines
dmaengine: idxd: add sysfs ABI for idxd driver
dmaengine: idxd: add configuration component of driver
dmaengine: idxd: Init and probe for Intel data accelerators
dmaengine: add support to dynamic register/unregister of channels
dmaengine: break out channel registration
x86/asm: add iosubmit_cmds512() based on MOVDIR64B CPU instruction
dmaengine: ti: k3-udma: fix spelling mistake "limted" -> "limited"
dmaengine: s3c24xx-dma: fix spelling mistake "to" -> "too"
dmaengine: Move dma_get_{,any_}slave_channel() to private dmaengine.h
dmaengine: Remove dma_request_slave_channel_compat() wrapper
dmaengine: Remove dma_device_satisfies_mask() wrapper
dt-bindings: fsl-imx-sdma: Add i.MX8MM/i.MX8MN/i.MX8MP compatible string
dmaengine: zynqmp_dma: fix burst length configuration
dmaengine: sun4i: Add support for cyclic requests with dedicated DMA
dmaengine: fsl-qdma: fix duplicated argument to &&
...
- Extend firmware interface for feature checking
- Use mailbox for communication with firmware for power management
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXibIfgAKCRDKSWXLKUoM
ISEiAJ0dOki4FCVTEloO1IIcbgY38SgvlwCfTSN4RQThu5iiG40ODZp4cJMaZmA=
=jGIz
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-soc-for-v5.6' of https://github.com/Xilinx/linux-xlnx into arm/drivers
arm64: soc: ZynqMP SoC changes for v5.6
- Extend firmware interface for feature checking
- Use mailbox for communication with firmware for power management
* tag 'zynqmp-soc-for-v5.6' of https://github.com/Xilinx/linux-xlnx:
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: firmware: xilinx: Add support for feature check
Link: https://lore.kernel.org/r/f6fb26f8-b00d-a3e8-bf7d-c7ff2a8483b1@monstr.eu
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for init suspend callback through mailbox IPI callback.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- clean ups of unused code and debuggability
- add cmdq_instruction to make the function call interface more readable
- add functions for polling and providing info for the user of cmdq
scpsys:
- add bindings for MT6765
-----BEGIN PGP SIGNATURE-----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=Q9/6
-----END PGP SIGNATURE-----
Merge tag 'v5.5-next-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
cmdq:
- clean ups of unused code and debuggability
- add cmdq_instruction to make the function call interface more readable
- add functions for polling and providing info for the user of cmdq
scpsys:
- add bindings for MT6765
* tag 'v5.5-next-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
soc: mediatek: cmdq: add cmdq_dev_get_client_reg function
soc: mediatek: cmdq: add polling function
soc: mediatek: cmdq: define the instruction struct
soc: mediatek: cmdq: remove OR opertaion from err return
Link: https://lore.kernel.org/r/9b365e76-e346-f813-d750-d7cfd0d16e4e@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
inst->handles is traversed using list_for_each_entry_rcu
outside an RCU read-side critical section but under the protection
of knav_dev_lock.
Hence, add corresponding lockdep expression to silence false-positive
lockdep warnings, and harden RCU lists.
Add macro for the corresponding lockdep expression.
Link: https://lore.kernel.org/r/20200118042433.4968-1-frextrite@gmail.com
Signed-off-by: Amol Grover <frextrite@gmail.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
enable straightforward passing of work between a producer and a consumer.
There is one RINGACC module per NAVSS on TI AM65x SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=m1rI
-----END PGP SIGNATURE-----
Merge tag 'drivers_soc_for_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into arm/drivers
SOC: TI Keystone Ring Accelerator driver
The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
enable straightforward passing of work between a producer and a consumer.
There is one RINGACC module per NAVSS on TI AM65x SoCs.
* tag 'drivers_soc_for_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
soc: ti: k3: add navss ringacc driver
bindings: soc: ti: add documentation for k3 ringacc
Link: https://lore.kernel.org/r/1579205259-4845-1-git-send-email-santosh.shilimkar@oracle.com
Signed-off-by: Olof Johansson <olof@lixom.net>
I've been sitting on these longer than I meant, so the patch count is
a bit higher than ideal for this part of the release. There's also some
reverts of double-applied patches that brings the diffstat up a bit.
With that said, the biggest changes are:
- Revert of duplicate i2c device addition on two Aspeed (BMC) Devicetrees.
- Move of two device nodes that got applied to the wrong part of the
tree on ASpeed G6.
- Regulator fix for Beaglebone X15 (adding 12/5V supplies)
- Use interrupts for keys on Amlogic SM1 to avoid missed polls
In addition to that, there is a collection of smaller DT fixes:
- Power supply assignment fixes for i.MX6
- Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit
- Build fixlets (selects) for davinci/omap2+
- More interrupt number fixes for Stratix10, Amlogic SM1, etc.
- ... and more similar fixes across different platforms
And some non-DT stuff:
- optee fix to register multiple shared pages properly
- Clock calculation fixes for MMP3
- Clock fixes for OMAP as well
-----BEGIN PGP SIGNATURE-----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=MMJu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I've been sitting on these longer than I meant, so the patch count is
a bit higher than ideal for this part of the release. There's also
some reverts of double-applied patches that brings the diffstat up a
bit.
With that said, the biggest changes are:
- Revert of duplicate i2c device addition on two Aspeed (BMC)
Devicetrees.
- Move of two device nodes that got applied to the wrong part of the
tree on ASpeed G6.
- Regulator fix for Beaglebone X15 (adding 12/5V supplies)
- Use interrupts for keys on Amlogic SM1 to avoid missed polls
In addition to that, there is a collection of smaller DT fixes:
- Power supply assignment fixes for i.MX6
- Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit
- Build fixlets (selects) for davinci/omap2+
- More interrupt number fixes for Stratix10, Amlogic SM1, etc.
- ... and more similar fixes across different platforms
And some non-DT stuff:
- optee fix to register multiple shared pages properly
- Clock calculation fixes for MMP3
- Clock fixes for OMAP as well"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
MAINTAINERS: Add myself as the co-maintainer for Actions Semi platforms
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
ARM: omap2plus: select RESET_CONTROLLER
ARM: davinci: select CONFIG_RESET_CONTROLLER
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
ARM: dts: mmp3: Fix the TWSI ranges
clk: mmp2: Fix the order of timer mux parents
ARM: mmp: do not divide the clock rate
arm64: dts: rockchip: Fix IR on Beelink A1
optee: Fix multi page dynamic shm pool alloc
...
* SCM major refactoring and cleanup
* Properly flag active only power domains as active only
* Add SC7180 and SM8150 RPMH power domains
* Return EPROBE_DEFER from QMI if packet family is not yet available
-----BEGIN PGP SIGNATURE-----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=IcVk
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.6
* SCM major refactoring and cleanup
* Properly flag active only power domains as active only
* Add SC7180 and SM8150 RPMH power domains
* Return EPROBE_DEFER from QMI if packet family is not yet available
* tag 'qcom-drivers-for-5.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (27 commits)
firmware: qcom_scm: Dynamically support SMCCC and legacy conventions
firmware: qcom_scm: Remove thin wrappers
firmware: qcom_scm: Order functions, definitions by service/command
firmware: qcom_scm-32: Add device argument to atomic calls
firmware: qcom_scm-32: Create common legacy atomic call
firmware: qcom_scm-32: Move SMCCC register filling to qcom_scm_call
firmware: qcom_scm-32: Use qcom_scm_desc in non-atomic calls
firmware: qcom_scm-32: Add funcnum IDs
firmware: qcom_scm-32: Use SMC arch wrappers
firmware: qcom_scm-64: Improve SMC convention detection
firmware: qcom_scm-64: Move SMC register filling to qcom_scm_call_smccc
firmware: qcom_scm-64: Add SCM results struct
firmware: qcom_scm-64: Move svc/cmd/owner into qcom_scm_desc
firmware: qcom_scm-64: Make SMC macros less magical
firmware: qcom_scm: Remove unused qcom_scm_get_version
firmware: qcom_scm: Apply consistent naming scheme to command IDs
firmware: qcom_scm: Rename macros and structures
soc: qcom: rpmhpd: Set 'active_only' for active only power domains
firmware: scm: Add stubs for OCMEM and restore_sec_cfg_available
dt-bindings: power: rpmpd: Convert rpmpd bindings to yaml
...
Link: https://lore.kernel.org/r/20200113204405.GD3325@yoga
Signed-off-by: Olof Johansson <olof@lixom.net>
QUICC Engine drivers
- Improve the QE drivers to be compatible with ARM/ARM64/PPC64
architectures
- Various cleanups to the QE drivers
-----BEGIN PGP SIGNATURE-----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=e4jk
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.6
QUICC Engine drivers
- Improve the QE drivers to be compatible with ARM/ARM64/PPC64
architectures
- Various cleanups to the QE drivers
* tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux: (49 commits)
soc: fsl: qe: remove set but not used variable 'mm_gc'
soc: fsl: qe: remove PPC32 dependency from CONFIG_QUICC_ENGINE
soc: fsl: qe: remove unused #include of asm/irq.h from ucc.c
net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32
net/wan/fsl_ucc_hdlc: reject muram offsets above 64K
net/wan/fsl_ucc_hdlc: fix reading of __be16 registers
net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE()
soc: fsl: qe: avoid IS_ERR_VALUE in ucc_fast.c
soc: fsl: qe: drop pointless check in qe_sdma_init()
soc: fsl: qe: drop use of IS_ERR_VALUE in qe_sdma_init()
soc: fsl: qe: avoid IS_ERR_VALUE in ucc_slow.c
soc: fsl: qe: refactor cpm_muram_alloc_common to prevent BUG on error path
soc: fsl: qe: drop broken lazy call of cpm_muram_init()
soc: fsl: qe: make cpm_muram_free() ignore a negative offset
soc: fsl: qe: make cpm_muram_free() return void
soc: fsl: qe: change return type of cpm_muram_alloc() to s32
serial: ucc_uart: access __be32 field using be32_to_cpu
serial: ucc_uart: limit brg-frequency workaround to PPC32
serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe()
serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32
...
Link: https://lore.kernel.org/r/1578608351-23289-1-git-send-email-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add i.MX8MP SoC driver support.
- Allow IMX DSP Protocol driver to be built as module.
- Add COMPILE_TEST for IMX_SCU_SOC driver to increase build coverage.
- Print SoC type and revision in i.MX8 SoC driver, as this is useful
information to have when looking through boot log.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl4bFOsUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5AYgf+NWY3ylMDPjrXwq5RUy/fD2QajJ2q
OQnSBg7PGkclh9Avzhj9YALsMzr4RSeXHNxxNA0wNQskNvu4cu6mTQs06F8o/9Qx
53g7LaIjfohjG4rLH4IIUiw1h47HxHJfJG18E0Rpx8+H/x8PX3CkbpMkWXmLQHvw
LgUzFAfeCZvB2t68LgjxKPLtq4xWcEyRFCB5S2y0BwF3JpICHjWaobsXoVuFMYny
YmCMBcweyqFk7n11r2SLbMMHH9VH+16nkEZ76M8enbLHFWSe5VxFEZxpWpmjfAyn
XJNmYSv1zPEIZBIpAl15ZHn+zxxwaY9JRaOwb+Ip7cCa9t/ZiT5OowDCLQ==
=8b1n
-----END PGP SIGNATURE-----
Merge tag 'imx-driver-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX driver changes for 5.6:
- Add i.MX8MP SoC driver support.
- Allow IMX DSP Protocol driver to be built as module.
- Add COMPILE_TEST for IMX_SCU_SOC driver to increase build coverage.
- Print SoC type and revision in i.MX8 SoC driver, as this is useful
information to have when looking through boot log.
* tag 'imx-driver-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
firmware: imx: Allow IMX DSP to be selected as module
soc: imx: Enable compile testing of IMX_SCU_SOC
soc: imx: Add i.MX8MP SoC driver support
soc: imx8: print SoC type and revision
Link: https://lore.kernel.org/r/20200113034006.17430-1-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds a couple of optimizations to how the chip ID and straps are
read and adds support for the FUSE block on Tegra194. Included is also a
small optimization for the coupled regulator driver to abort early if no
voltage change has occurred.
-----BEGIN PGP SIGNATURE-----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=mbxz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.6-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc: tegra: Changes for v5.6-rc1
This adds a couple of optimizations to how the chip ID and straps are
read and adds support for the FUSE block on Tegra194. Included is also a
small optimization for the coupled regulator driver to abort early if no
voltage change has occurred.
* tag 'tegra-for-5.6-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
soc/tegra: regulators: Do nothing if voltage is unchanged
soc/tegra: fuse: Add APB DMA dependency for Tegra20
soc/tegra: fuse: Add Tegra194 support
Link: https://lore.kernel.org/r/20200111003553.2411874-4-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
enable straightforward passing of work between a producer and a consumer.
There is one RINGACC module per NAVSS on TI AM65x SoCs.
The RINGACC converts constant-address read and write accesses to equivalent
read or write accesses to a circular data structure in memory. The RINGACC
eliminates the need for each DMA controller which needs to access ring
elements from having to know the current state of the ring (base address,
current offset). The DMA controller performs a read or write access to a
specific address range (which maps to the source interface on the RINGACC)
and the RINGACC replaces the address for the transaction with a new address
which corresponds to the head or tail element of the ring (head for reads,
tail for writes). Since the RINGACC maintains the state, multiple DMA
controllers or channels are allowed to coherently share the same rings as
applicable. The RINGACC is able to place data which is destined towards
software into cached memory directly.
Supported ring modes:
- Ring Mode
- Messaging Mode
- Credentials Mode
- Queue Manager Mode
TI-SCI integration:
Texas Instrument's System Control Interface (TI-SCI) Message Protocol now
has control over Ringacc module resources management (RM) and Rings
configuration.
The corresponding support of TI-SCI Ringacc module RM protocol
introduced as option through DT parameters:
- ti,sci: phandle on TI-SCI firmware controller DT node
- ti,sci-dev-id: TI-SCI device identifier as per TI-SCI firmware spec
if both parameters present - Ringacc driver will configure/free/reset Rings
using TI-SCI Message Ringacc RM Protocol.
The Ringacc driver manages Rings allocation by itself now and requests
TI-SCI firmware to allocate and configure specific Rings only. It's done
this way because, Linux driver implements two stage Rings allocation and
configuration (allocate ring and configure ring) while TI-SCI Message
Protocol supports only one combined operation (allocate+configure).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The commit 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
moves the sifive L2 cache driver to driver/soc. It did not move the
header file along with the driver. Therefore this patch moves the header
file to driver/soc
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: updated to fix the include guard]
Fixes: 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
changes for 5.6, please pull the following:
- Florian provides a set of updates to the Bus Interface Unit control to
tune it appropriately for the most recent chips: 7255, 7260, 7216, 7211
-----BEGIN PGP SIGNATURE-----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=ZiDk
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.6/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom ARM/ARM64/MIPS-based SoCs drivers
changes for 5.6, please pull the following:
- Florian provides a set of updates to the Bus Interface Unit control to
tune it appropriately for the most recent chips: 7255, 7260, 7216, 7211
* tag 'arm-soc/for-5.6/drivers' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: biuctrl: Update programming for 7211
soc: bcm: brcmstb: biuctrl: Update layout for A72 on 7211
soc: bcm: brcmstb: biuctrl: Tune interface for 7255 and 7216
soc: bcm: brcmstb: biuctrl: Tune 7260 BIU interface
Link: https://lore.kernel.org/r/20200108191114.15987-2-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Both Chip ID and strapping registers are now read out during of APB MISC
initialization, the registers' mapping isn't needed anymore once registers
are read. Hence let's unmap registers once they are not needed anymore,
for consistency.
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Trying to read out Chip ID before APBMISC registers are mapped won't
succeed, in a result Tegra124 gets a wrong address for the HW straps
register if machine uses an old outdated device tree.
Fixes: 297c4f3dcb ("soc/tegra: fuse: Restrict legacy code to 32-bit ARM")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now both Chip ID and HW straps are becoming available at the same time,
thus we could simply check the availability of the ID in order to check
the availability of the straps. We couldn't check straps for 0x0 because
it could be a correct value.
This change didn't uncover any problems, but anyways it is nicer to have
straps verified for consistency with the Chip ID verification.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is no need to re-read Chip ID and HW straps out from hardware each
time, it is a bit nicer to cache the values in memory.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is no need to re-apply the same voltage. This change is just a minor
cleanup.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Define CMDQ_EOC_CMD was actually never used. Delete it.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
IMX_SCU_SOC can be compile tested to increase build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
drivers/soc/fsl/qe/gpio.c: In function qe_pin_request:
drivers/soc/fsl/qe/gpio.c:163:26: warning: variable mm_gc set but not used [-Wunused-but-set-variable]
commit 1e714e54b5 ("powerpc: qe_lib-gpio: use gpiochip data pointer")
left behind this unused variable.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
corresponding cpuidle driver. This support is based upon using the generic
PM domain, which already supports devices belonging to CPUs.
Finally, these is a DTS patch that enables the hierarchical topology to be
used for the Qcom 410c Dragonboard, which supports the PSCI OS-initiated
mode.
-----BEGIN PGP SIGNATURE-----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=WFox
-----END PGP SIGNATURE-----
Merge tag 'cpuidle_psci-v5.5-rc4' of git://git.linaro.org/people/ulf.hansson/linux-pm into arm/drivers
Initial support for hierarchical CPU arrangement, managed by PSCI and its
corresponding cpuidle driver. This support is based upon using the generic
PM domain, which already supports devices belonging to CPUs.
Finally, these is a DTS patch that enables the hierarchical topology to be
used for the Qcom 410c Dragonboard, which supports the PSCI OS-initiated
mode.
* tag 'cpuidle_psci-v5.5-rc4' of git://git.linaro.org/people/ulf.hansson/linux-pm: (611 commits)
arm64: dts: Convert to the hierarchical CPU topology layout for MSM8916
cpuidle: psci: Add support for PM domains by using genpd
PM / Domains: Introduce a genpd OF helper that removes a subdomain
cpuidle: psci: Support CPU hotplug for the hierarchical model
cpuidle: psci: Manage runtime PM in the idle path
cpuidle: psci: Prepare to use OS initiated suspend mode via PM domains
cpuidle: psci: Attach CPU devices to their PM domains
cpuidle: psci: Add a helper to attach a CPU to its PM domain
cpuidle: psci: Support hierarchical CPU idle states
cpuidle: psci: Simplify OF parsing of CPU idle state nodes
cpuidle: dt: Support hierarchical CPU idle states
of: base: Add of_get_cpu_state_node() to get idle states for a CPU node
firmware: psci: Export functions to manage the OSI mode
dt: psci: Update DT bindings to support hierarchical PSCI states
cpuidle: psci: Align psci_power_state count with idle state count
Linux 5.5-rc4
locks: print unsigned ino in /proc/locks
riscv: export flush_icache_all to modules
riscv: reject invalid syscalls below -1
riscv: fix compile failure with EXPORT_SYMBOL() & !MMU
...
Link: https://lore.kernel.org/r/20200102160820.3572-1-ulf.hansson@linaro.org
Signed-off-by: Olof Johansson <olof@lixom.net>
GCE cannot know the register base address, this function
can help cmdq client to get the cmdq_client_reg structure.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add polling function in cmdq helper functions
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Define an instruction structure for gce driver to append command.
This structure can make the client's code more readability.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Debugging gets harder if we OR two error return values.
Return each error on it's own instead
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
[mb: rephrase commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The 'active_only' attribute was accidentally never set to true for any
power domains meaning that all the code handling this attribute was
dead.
NOTE that the RPM power domain code (as opposed to the RPMh one) gets
this right.
Acked-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20190214173633.211000-1-dianders@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Despite using the same compatible values ("r8a7795"-based) because of
historical reasons, R-Car H3 ES1.x (R8A77950) and R-Car H3 ES2.0+
(R8A77951) are really different SoCs, with different part numbers.
Reflect this in the SoC configuration, by adding CONFIG_ARCH_R8A77950
and CONFIG_ARCH_R8A77951 as new config symbols. These are intended to
replace CONFIG_ARCH_R8A7795, and will allow making support for early SoC
revisions optional.
Note that for now, CONFIG_ARCH_R8A7795 is retained, and just selects
CONFIG_ARCH_R8A77950 and CONFIG_ARCH_R8A77951. This relaxes
dependencies of other subsystems on the SoC configuration symbol, and
provides a smooth transition path for config files through "make
oldconfig".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191217183841.432-6-geert+renesas@glider.be
The configure call back takes a register pointer, so should
have been marked with __iomem. Add this to silence the
following sparse warnings:
drivers/soc/renesas/rcar-rst.c:33:22: warning: incorrect type in initializer (incompatible argument 1 (different address spaces))
drivers/soc/renesas/rcar-rst.c:33:22: expected int ( *configure )( ... )
drivers/soc/renesas/rcar-rst.c:33:22: got int ( * )( ... )
drivers/soc/renesas/rcar-rst.c:97:40: warning: incorrect type in argument 1 (different address spaces)
drivers/soc/renesas/rcar-rst.c:97:40: expected void *base
drivers/soc/renesas/rcar-rst.c:97:40: got void [noderef] <asn:2> *[assigned] base
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191218135230.2610161-1-ben.dooks@codethink.co.uk
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add a matching entry for 7211 which can be programmed with the same
BIUCTRL settings as other Brahma-B53 based SoCs. While at it, rename the
function to include a72 in the name to reflect this applies to both
types of 64-bit capable CPUs that we support (Brahma-B53 and
Cortex-A72).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The BIUCTRL layout is a little different on 7211 which is equipped with
a Cortex-A72, account for those register offset differences. We will
match 7211 specifically in a subsequent commit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
7255 and 7216 are some of the latest chips that were produced and
support the full register range configuration for the BIU, add the two
entries to get the expected programming.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
7260A0 and B0 are both supported, and 7260A0 has a small difference in
that it does not support the write-back control register, which is why
we have a different array of registers. Update the comment above
b53_cpubiuctrl_no_wb_regs to denote that difference.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133925.13712-1-krzk@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The sifive_l2_cache.c is in no way related to RISC-V architecture
memory management. It is a little stub driver working around the fact
that the EDAC maintainers prefer their drivers to be structured in a
certain way that doesn't fit the SiFive SOCs.
Move the file to drivers/soc and add a Kconfig option for it, as well
as the whole drivers/soc boilerplate for CONFIG_SOC_SIFIVE.
Fixes: a967a289f1 ("RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
[paul.walmsley@sifive.com: keep the MAINTAINERS change specific to the L2$ controller code]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Any user of wkup_m3_ipc calls wkup_m3_ipc_get to get a handle and this
checks the value of the static variable m3_ipc_state to see if the
wkup_m3 is ready. Currently this is populated during probe before
rproc_boot has been called, meaning there is a window of time that
wkup_m3_ipc_get can return a valid handle but the wkup_m3 itself is not
ready, leading to invalid IPC calls to the wkup_m3 and system
instability.
To avoid this, move the population of the m3_ipc_state variable until
after rproc_boot has succeeded to guarantee a valid and usable handle
is always returned.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
If a client comes up early in the boot process (perhaps was a built-in
driver), qmi_handle_init() will likely fail with a EAFNOSUPPORT since the
underlying ipc router hasn't init'd and registered the address family.
This should not be a fatal error since chances are, the router will come
up later, so recode the error to EPROBE_DEFER so that clients will retry
later.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20191106230511.1290-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
pm_genpd_init() can return an error. Propagate the error code to prevent
the driver from indicating that it successfully probed while there were
errors during pm_genpd_init().
Fixes: eef3c2ba0a ("soc: amlogic: Add support for Everything-Else power domains controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
of_genpd_add_provider_onecell() can return an error. Propagate the error
so the driver registration fails when of_genpd_add_provider_onecell()
did not work.
Fixes: eef3c2ba0a ("soc: amlogic: Add support for Everything-Else power domains controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There are also PPC64, ARM and ARM64 based SOCs with a QUICC Engine,
and the core QE code as well as net/wan/fsl_ucc_hdlc and
tty/serial/ucc_uart has now been modified to not rely on ppcisms.
So extend the architectures that can select QUICC_ENGINE, and add the
rather modest requirements of OF && HAS_IOMEM.
The core code as well as the ucc_uart driver has been tested on an
LS1021A (arm), and it has also been tested that the QE code still
works on an mpc8309 (ppc). Qiang Zhao has tested that the QE-HDLC code
that gets enabled with this works on ARM64.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When allowing this driver to be built for ARM, the build fails (for
CONFIG_SMP=y) since ARM's asm/irq.h header is not self-contained:
In file included from drivers/soc/fsl/qe/ucc.c:18:0:
>> arch/arm/include/asm/irq.h:34:50: error: unknown type name 'cpumask_t'
extern void arch_trigger_cpumask_backtrace(const cpumask_t *mask,
But nothing in this file actually uses anything from asm/irq.h -
removing this #include generates identical object code, both on PPC32
and on ARM (the latter with a patch added to asm/irq.h to make the
build work in the first place).
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When building this on a 64-bit platform gcc rightly warns that the
error checking is broken (-ENOMEM stored in an u32 does not compare
greater than (unsigned long)-MAX_ERRNO). Instead, change the
ucc_fast_[tr]x_virtual_fifo_base_offset members to s32 and use an
ordinary check-for-negative. Also, this avoids treating 0 as "this
cannot have been returned from qe_muram_alloc() so don't free it".
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The sdma member of struct qe_immap is not at offset zero, so even if
qe_immr wasn't initialized yet (i.e. NULL), &qe_immr->sdma would not
be NULL.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Now that qe_muram_alloc() returns s32, adapt qe_sdma_init() and avoid
another few IS_ERR_VALUE() uses.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When trying to build this for a 64-bit platform, one gets warnings
from using IS_ERR_VALUE on something which is not sizeof(long).
Instead, change the various *_offset fields to store a signed integer,
and simply check for a negative return from qe_muram_alloc(). Since
qe_muram_free() now accepts and ignores a negative argument, we only
need to make sure these fields are initialized with -1, and we can
just unconditionally call qe_muram_free() in ucc_slow_free().
Note that the error case for us_pram_offset failed to set that field
to 0 (which, as noted earlier, is anyway a bogus sentinel value).
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
