The index calculated when looping through the indir array passed to
fm10k_write_reta was incorrectly calculated as the first part i needs to
be multiplied by 4.
Fixes: 0cfea7a65738 ("fm10k: fix possible null pointer deref after kcalloc", 2016-04-13)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While reviewing the i40e driver changes to support page based receive I
realized that I had overlooked the fact that the fm10k hardware required a
512 byte alignment for Rx buffers. This patch is meant to address that by
changing the alignment for Rx buffers to 512 bytes instead of allowing it
to be L1 cache aligned.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FM10K_MAX_DATA_PER_TXD is really just using a bitshift as a power of
2 operation in an efficient manner. We shouldn't represent this as a BIT()
because that obscures the intention of the operation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-06-27
This series contains updates to i40e and i40evf only.
Mitch provides several changes, first adds functions to enable and disable
VSI on a VEB, which allows for configuration of limited promiscuous mode
specifically for bridging purposes. Sets the RSS Hash Enable registers by
default now that VF RSS is configured by the PF driver. Fixed a issue
where we could overflow the buffer, by checking the address count and bail
out of the loop at the appropriate time. Removed the need for a reset
when the device enters limited promiscuous mode, since this was causing
heartburn for people who were using VFs and bridging.
Catherine adds a call to set the client interface down when we put the VSI
down. Fixed an issue where RSS queues was being limited to the number
of CPUs, so if a user wants to use more queues than CPUs, we want to
trust they know what they are doing and let them.
Greg cleans up the driver suspend routine to ensure we are calling
synchronize_irq() before freeing IRQ vectors and explicitly free the other
causes interrupt resources and shut down the MSIX interrupt.
Serey fixes i40e_set_settings() to not fail when a Direct Attach (DA)
cable is used.
Avinash fixes a supported link bug by removing code which was not allowing
100BaseT to show up in the supported link modes for 10GBaseT PHYs.
Shannon adds a bit of information to the error messages to help determine
the source of error by adding VSI info to macaddr messages.
Tushar Dave fixes error received when turning off TSO on some systems,
which was caused by enabling FD_SB without checking availability of
MSIx vectors, so add the check.
Neerav fixes a possible panic when LLDP/DCBX change happens and the
driver tried to notify the client(s) for each of the PF VSIs, which would
panic when it reached a VSI that did not have any netdev associated with
it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_unshare() fails, we call qdisc_drop() with a NULL skb, which
is no longer supported.
Fixes: 520ac30f45 ("net_sched: drop packets after root qdisc lock is released")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
qed*: Fix the static checker warnings.
The patch series addresses the static checker warnings introduced by the
earlier patches related to qed/qede coalesce configuration support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Static checker warnings:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:435 qede_get_coalesce()
warn: passing casted pointer '&coal->rx_coalesce_usecs' to
'edev->ops->common->get_coalesce()' 32 vs 16.
The u32 pointer is being typecasted to u16 which may fail for big-endian
platforms.
Fixes: d552fa84cb ("qede: Add support for coalescing config read/update.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Context implies that port in struct "udp_media_addr" is referring
to a UDP port.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP msg2addr function tipc_udp_msg2addr() can return -EINVAL which
prior to this patch was unhanded in the caller.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The space is missing before the open parenthesis '(', and this
will introduce much more noise when checking patch around.
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some configurations, gcc produces a warning for correct code
in this driver:
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read64':
drivers/net/dsa/b53/b53_mmap.c:107:10: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
^~~~~~~
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read48':
drivers/net/dsa/b53/b53_mmap.c:91:11: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
^~~~~~~
drivers/net/dsa/b53/b53_mmap.c:83:11: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 16) | lo;
I have seen the warning before and at the time thought I had fixed
it with 55e7f6abe1 ("dsa: b53: fix big-endian register access"),
however it now came back in a different randconfig build that happens
to have different inlining decisions in the compiler.
The mistake that gcc makes here is that it thinks the second call to
readl() might fail because the address 'reg + 4' is not a multiple
of four despite having knowing that 'reg' itself is a multiple of four.
By open-coding the two reads without the redundant alignment check,
we can avoid the warning and produce slightly better object code, but
get slightly longer source code instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI CPDMA currently uses a bitmap for tracking descriptors alloactions
allocations, but The genalloc already handles the same and can be used
as with special memory (SRAM) as with DMA cherent memory chank
(dma_alloc_coherent()). Hence, switch to using genalloc and add
desc_num property for each channel for limitation of max number of
allowed descriptors for each CPDMA channel. This patch do not affect
on net throuput.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko says:
====================
drivers: net: cpsw: improve runtime pm
This series intended to improve runtime PM and allow CPSW to be
RPM suspended when all ethX netdevices are down.
To achieve above goal it is required to relax runtime PM constraints for
Davinci MDIO which blocks CPSW runtime PM now, because Davinci MDIO is always
powered on during probe and powered off only when it's going to be removed.
- Patches 6-11 implement PM runtime autosuspend for Davinci MDIO, but keep it
disabled by default, because Davinci MDIO is integrated in big set of TI devices
and not all of them verified to work correctly with RPM autosuspend enabled:
expected to work on SoCs where MDIO is defined as part of CPSW in DT
(cpsw.c DRA7/am57x, am437x, am335x)
The CPSW need to be fixed before RPM suspended can be allowed:
- Patches 1-5 ensure that CPSW will not cause L3 errors while it is in RPM
suspended state.
Davinci MDIO RPM autosuspend can be enabled through sysfs:
echo 100 > /sys/devices/../48484000.ethernet/48485000.mdio/power/autosuspend_delay_ms
Patches 12 - 15: introduce new compatible string "ti,cpsw-mdio" which is used
then to enable RPM for am335x/am437x/dra7 SoCs.
Tested on am335x, am437x, am572x and k2g (on k2g with RPM disabled for Davinci MDIO)
These changes should not affect on errata i877 implementation on DRA7.
Power measurement on am335x GP EVM:
Without this series: 547.60 mW total SoC power
With this series + "ifconfig eth0 down": 477.32 mW Total Soc Power
Changes in v2:
- CPSW ethtool interface updated to use .begin()/.complete() callbacks
- kbuild failure fixed
- davinci_mdio DT updated with proper description of allowed compatible strings
combinations
Link on v1:
https://lkml.org/lkml/2016/6/15/362
====================
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "ti,cpsw-mdio" for am335x/am437x/dra7 SoCs where MDIO is
implemented as part of TI CPSW and, this way, enable PM runtime auto
suspend for Davinci MDIO driver on these paltforms.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "ti,cpsw-mdio" to enable PM runtime auto-suspend on supported
platforms, where MDIO is implemented as part of TI CPSW.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce "ti,cpsw-mdio" compatible string for Davinci MDIO, because
it's required to distinguish the case when MDIO is part of TI CPSW to
enable features supported by TI CPSW (for example, enable PM
management).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document missed "ti,am4372-mdio" compat string used for TI am437x SoC
(am4372.dtsi).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davinci MDIO is always used as slave device which services
read/write requests from MDIO/PHY core. It doesn't use IRQ also.
As result, It's possible to relax PM runtime constraints for Davinci
MDIO and enable it on demand, instead of powering it during probe
and powering off during removal.
Hence, implement PM runtime autosuspend for Davinci MDIO, but keep it
disabled by default, because Davinci MDIO is integrated in big set of
TI devices and not all of them expected to work corectly with RPM
autosuspend enabled:
- expected to work on SoCs where MDIO is part of TI CPSW
(cpsw.c DRA7/am57x, am437x, am335x, dm814x)
- not verified on Keystone 2 and other SoCs where MDIO is used with TI EMAC IP
(davinci_emac.c: dm6467-emac, am3517-emac, dm816-emac).
Davinci MDIO RPM autosuspend can be enabled through sysfs:
echo 100 > /sys/devices/../48484000.ethernet/48485000.mdio/power/autosuspend_delay_ms
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PM runtime .runtime_suspend()/.runtime_resume() callbacks and
perform Davinci MDIO enabling/disabling from these callbacks. This
allows to reuse pm_runtime_force_suspend/resume() APIs during System
suspend and required for further implementation of PM runtime
autosuspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Davinci MDIO MDIO_CONTROL.CLKDIV can be calculated only once
during probe, hence split __davinci_mdio_reset() on
davinci_mdio_init_clk() and davinci_mdio_enable(). Initialize and
save CLKDIV in .probe(). Then just use saved value.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not expected Davinci MDIO to be accessible after its suspend
callbacks have been called:
- all consumers of Davinci MDIO will stop/disconnect phys at Device
suspend stage;
- all phys are expected to be suspned already by PHY/MDIO core;
- MDIO locking is done by MDIO Bus code.
Hence, it's safe to drop "suspended" and "lock" fields from mdio_data.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PM runtime is disabled when Davinci MDIO .suspend_late() and
.resume_early() callbacks are called. As result, any PM runtime calls here will
be just a nop and can be removed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do PM runtime initialization later in probe - this allows to simplify
error handling a bit.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through net_device_ops interfce. In
this case net_device_ops operations requiring registers access will
cause L3 errors and CPSW crash.
Hence, fix it by adding RPM get/put calls in net_device_ops callbacks
which need to access CPSW registers: .ndo_set_mac_address(),
.ndo_vlan_rx_add_vid(), .ndo_vlan_rx_kill_vid().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through ethtool interfce. In this case
ethtool operations, requiring registers access, will cause L3 errors and
CPSW crash.
ethtool callbcaks which need to access CPSW registers now:
.set_coalesce(), .get_ethtool_stats(), .set_pauseparam(), .get_regs()
Hence, fix it by adding .begin()/.complete() ethtool callbacks, which
will be called before/after each ethtool operation runs, and do CPSW
RPM handling in these callbacks. That way CPSW will be active while
handling ethtool requests.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PM runtime is properly handled in cpsw_ndo_open/stop(), as result it
isn't required to duplicate these calls in .suspend()/.resume()
callbacks. Moreover, it might cause unnecessary RPM resume of CPSW
during System suspend in the case it's already suspended because
all ethX interfaces are down already, before System suspend started.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed check of return code from PM runtime get() calls.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw_suspend() could trigger L3 error and CPSW will stop
functioning if System enters suspend when all ethX net-devices are
down - in this case CPSW could be already suspended by PM runtime, but
cpsw_suspend() will try to call soft_reset_slave() unconditionally
and access CPSW registers.
Hence, fix it by moving soft_reset_slave() from cpsw_suspend() to
cpsw_slave_stop(). This way slave ports will be reset when CPSW is
active and will be in proper state during Suspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe Cavallaro says:
====================
stmmac: rework and enhance the PCS support
The 3.xx and 4.xx synopsys gmacs have a very similar
PCS embedded module and they share almost the same registers;
for example:
AN_Control, AN_Status, AN_Advertisement, AN_Link_Partner_Ability,
AN_Expansion, TBI_Extended_Status.
Just the RGMII/SMII Control/Status register differs.
So these patches aim to reorganize and enhance the PCS support;
to do that, some small inline functions have been provided and
also some rework to the PCS ISR part has been done.
In the end, the SGMII for MAC2MAC connection has been introduced.
All patches have been built on top of net-next git and, as for
the previous version, not fully tested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of SGMII more, for example when a MAC2MAC connection
is needed, the port selection bits (inside the MAC configuration
registers) have to be programmed according to the link selected.
So the patch adds a new DT parameter to pass the port selection
and to programmed related PCS and CORE to use it.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, all gmac cores disable the PCS block and always
enable the PMT.
Note that this is done in a different way by 3.x and 4.x cores.
With this rework, PCS and PMT interrupt masks can be driven by
parameters now moved inside the mac_device_info structure
and the settings follow what the HW capability register reports.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3.xx and 4.xx synopsys gmacs have a very similar
PCS embedded module and they share almost the same registers:
for example:
AN_Control, AN_Status, AN_Advertisement, AN_Link_Partner_Ability,
AN_Expansion, TBI_Extended_Status.
Just the RGMII/SMII Control/Status register differs.
So This patch aims to reorganize and enhance the PCS support.
It removes the existent support from the dwmac1000/dwmac4_core.c
moving basic PCS functions inside a new file called: stmmac_pcs.h.
The patch also reviews the available APIs to be better shared among
different hardware and easily enhanced to support new features.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling the fixed-phy functions when CONFIG_FIXED_PHY=m as a previous
change tried cannot work if the caller is in built-in code:
drivers/of/built-in.o: In function `of_phy_register_fixed_link':
of_reserved_mem.c:(.text+0x85e0): undefined reference to `fixed_phy_register'
Making of_mdio depend on 'FIXED_PHY || !FIXED_PHY' would solve this
dependency by enforcing that OF_MDIO itself becomes a loadable module
when FIXED_PHY=y, but that creates a different dependency as it
breaks any built-in ethernet driver that uses of_mdio.
Making FIXED_PHY a bool option also cannot work, since it depends on
PHYLIB, which again is tristate.
This version now uses 'select FIXED_PHY' to ensure that the fixed-phy
portion of of_mdio is not optional. The main downside of this is
a small increase in code size for cases that do not need fixed phy
support, but it should avoid all of the link-time problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d1bd330a22 ("of_mdio: Enable fixed PHY support if driver is a module")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop redundant include of moduleparam.h
The Coccinelle semantic patch used to make this change is as follows:
@ includesmodule @
@@
#include <linux/module.h>
@ depends on includesmodule @
@@
- #include <linux/moduleparam.h>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to inet_diag facility to filter sockets based on device
index. If an interface index is in the filter only sockets bound
to that index (sk_bound_dev_if) are returned.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
