According to the datasheets of AW200xx devices, the software reset takes
at least 1ms. Therefore, it is required to add a delay after the
reset before issuing commands to the device.
Signed-off-by: George Stark <gnstark@salutedevices.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Link: https://lore.kernel.org/r/20231125200519.1750-7-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
Get rid of device tree property "awinic,display-rows". The property
value actually means number of current switches and depends on how LEDs
are connected to the device. It should be calculated manually by max
used LED number. In the same way it is computed automatically now.
Max used LED is taken from LED definition subnodes.
Signed-off-by: George Stark <gnstark@salutedevices.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20231125200519.1750-5-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
HWEN is hardware control, which is used for enable/disable aw200xx chip.
It's high active, internally pulled down to GND.
After HWEN pin set high the chip begins to load the OTP information,
which takes 200us to complete. About 200us wait time is needed for
internal oscillator startup and display SRAM initialization. After
display SRAM initialization, the registers in page 1 to page 5 can be
configured via i2c interface.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Link: https://lore.kernel.org/r/20231125200519.1750-3-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
If write only DIM value to the page 4, LED brightness will not be
updated, as both DIM and FADE need to be written to the page 4.
Therefore, write DIM to the page 1.
Fixes: 36a87f371b ("leds: Add AW20xx driver")
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20231125200519.1750-2-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
The serial tty interface also supports additional input signals, that
can also be evaluated within this trigger. This change is adding the
following additional input sources, which could be controlled
via the '/sys/class/<leds>/' sysfs interface.
Explanation:
DCE = Data Communication Equipment (Modem)
DTE = Data Terminal Equipment (Computer)
- cts:
DCE is ready to accept data from the DTE (CTS = Clear To Send). If
the line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate CTS.
If set to 1, the LED will evaluate CTS.
- dsr:
DCE is ready to receive and send data (DSR = Data Set Ready). If the
line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate DSR.
If set to 1, the LED will evaluate DSR.
- dcd:
DTE is receiving a carrier from the DCE (DCD = Data Carrier Detect).
If the line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate DCD.
If set to 1, the LED will evaluate DCD.
- rng:
DCE has detected an incoming ring signal on the telephone line
(RNG = Ring Indicator). If the line state is detected, the LED is
switched on.
If set to 0 (default), the LED will not evaluate RNG.
If set to 1, the LED will evaluate RNG.
Also add an invert flag on LED blink, so that the LED blinks in the
correct order.
* If one off the new enabled input signals are evaluatet as 'enabled',
and data are transmitted, then the LED should first blink 'off' and
then 'on' (invert).
* If all the new enabled input signals are evaluatet as 'disabled',
and data are transmitted, then the LED should first blink 'on' and
then 'off'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Maarten Brock <m.brock@vanmierlo.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-5-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
Until now, the LED blinks when data is sent via the tty (rx/tx).
This is not configurable.
This change adds the possibility to make the indication for the direction
of the transmitted data independently controllable via the new rx and
tx sysfs entries.
- rx:
Signal reception (rx) of data on the named tty device.
If set to 0, the LED will not blink on reception.
If set to 1 (default), the LED will blink on reception.
- tx:
Signal transmission (tx) of data on the named tty device.
If set to 0, the LED will not blink on transmission.
If set to 1 (default), the LED will blink on transmission.
This new sysfs entry are on by default. Thus the trigger behaves as
before this change.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-4-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
With this commit, the mutex handling is replaced by the completion
handling. When handling mutex, it must always be ensured that the held
mutex is also released again. This is more error-prone should the number
of code paths increase.
This is a preparatory commit to make the trigger more configurable via
additional sysfs parameters. With this change, the worker always runs and
is no longer stopped if no ttyname is set.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-3-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
One error path already used dev_err_probe(). Adapt the other error paths
that emit an error message to also use this function for consistency and
slightly simplified code.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231126095230.683204-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
With pwmchip_remove() being automatically called after switching to
devm_pwmchip_add() the remove function can be dropped completely. Yay!
With lpg_remove() gone there is no user of the platform device's drvdata
left, so platform_set_drvdata() can be dropped from .probe(), too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231126095230.683204-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
The ttyname buffer for the ledtrig_tty_data struct is allocated in the
sysfs ttyname_store() function. This buffer must be released on trigger
deactivation. This was missing and is thus a memory leak.
While we are at it, the TTY handler in the ledtrig_tty_data struct should
also be returned in case of the trigger deactivation call.
Cc: stable@vger.kernel.org
Fixes: fd4a641ac8 ("leds: trigger: implement a tty trigger")
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127081621.774866-1-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231103195310.948327-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
sscanf() is a heavy one and moreover requires additional boundary checks.
Convert driver to use kstrtou8() in gpio_trig_inverted_store().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231103195310.948327-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
gpiod_get_optional() and currently used fwnode_gpiod_get_index()
are both wrappers against the same engine internally. Since we
have a pointer to struct device there is no reason to use fwnode
type of GPIO call. So, replace the current fwnode call by respective
gpiod ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231103195310.948327-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
The AW2013 driver uses devm_regmap_init_i2c, so REGMAP_I2C needs to
be selected.
Otherwise build process may fail with:
ld: drivers/leds/leds-aw2013.o: in function `aw2013_probe':
leds-aw2013.c:345: undefined reference to `__devm_regmap_init_i2c'
Signed-off-by: Dang Huynh <danct12@riseup.net>
Acked-by: Nikita Travkin <nikita@trvn.ru>
Fixes: 59ea3c9faf ("leds: add aw2013 driver")
Link: https://lore.kernel.org/r/20231103114203.1108922-1-danct12@riseup.net
Signed-off-by: Lee Jones <lee@kernel.org>
Some Allwinner sunxi SoCs, starting with the A100, contain an LED
controller designed to drive RGB LED pixels. Add a driver for it using
the multicolor LED framework, and with LEDs defined in the device tree.
Acked-by: Guo Ren <guoren@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20231029212738.7871-3-samuel@sholland.org
Signed-off-by: Lee Jones <lee@kernel.org>
The register-bit-led binding now also supports 'reg' in addition to
'offset' for the register address. Add support to the driver to get the
address from 'reg'.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231025190619.881090-2-robh@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The commit c7d80059b0 ("leds: class: Store the color index in struct
led_classdev") introduced a new sysfs entry "color" that is commonly
created for the led classdev. Unfortunately, this conflicts with the
"color" sysfs entry of already existing drivers such as Logitech HID
or System76 ACPI drivers. The driver probe fails due to the conflict,
hence it leads to a severe regression with the missing keyboard, for
example.
This patch reverts partially the change in the commit above for
removing the led class color sysfs entries again for addressing the
regressions. The newly introduced led_classdev.color field is kept as
it's already used by other driver.
Fixes: c7d80059b0 ("leds: class: Store the color index in struct led_classdev")
Reported-by: Johannes Penßel <johannes.penssel@gmail.com>
Closes: https://lore.kernel.org/r/b5646db3-acff-45aa-baef-df3f660486fb@gmail.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218045
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218155
Link: https://bugzilla.suse.com/show_bug.cgi?id=1217172
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231121162359.9332-1-tiwai@suse.de
Signed-off-by: Lee Jones <lee@kernel.org>
This contains a few fixes and a bunch of cleanups, a lot of which is in
preparation for Uwe's character device support that may be ready in time
for the next merge window.
-----BEGIN PGP SIGNATURE-----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=S2DI
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains a few fixes and a bunch of cleanups, a lot of which is
in preparation for Uwe's character device support that may be ready in
time for the next merge window"
* tag 'pwm/for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: samsung: Document new member .channel in struct samsung_pwm_chip
pwm: bcm2835: Add support for suspend/resume
pwm: brcmstb: Checked clk_prepare_enable() return value
pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
pwm: pxa: Explicitly include correct DT includes
pwm: cros-ec: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: samsung: Consistently use the same name for driver data
pwm: vt8500: Simplify using devm functions
pwm: sprd: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: sprd: Provide a helper to cast a chip to driver data
pwm: spear: Simplify using devm functions
pwm: mtk-disp: Simplify using devm_pwmchip_add()
pwm: imx-tpm: Simplify using devm functions
pwm: brcmstb: Simplify using devm functions
pwm: bcm2835: Simplify using devm functions
pwm: bcm-iproc: Simplify using devm functions
pwm: Adapt sysfs API documentation to reality
pwm: dwc: add PWM bit unset in get_state call
pwm: dwc: make timer clock configurable
pwm: dwc: split pci out of core driver
...
- Add support for a bunch more colours
- New Drivers
- Add support for Kinetic KTD2026/7 RGB/White LEDs
- New Functionality
- Add support for device to enter HW Controlled Mode to Turris Omnia LEDs
- Add support for HW Gamma Correction to Turris Omnia LEDs
- Fix-ups
- Apply new __counted_by() annotation to several data structures containing flexible arrays
- Rid the return value from Platform's .remove() operation
- Use *_cansleep() variants for instances were threads can sleep
- Improve the semantics when setting the brightness
- Generic clean-ups; code reduction, coding style, standard patterns
- Replace strncpy() with strscpy()
- Fix-up / add various documentation
- Re-author the GPIO associated Trigger to use trigger-sources
- Move to using standard APIs and helpers
- Improve error checking
- Stop using static GPIO bases
- Bug Fixes
- Fix Pointer to Enum casing warnings
- Do not pretend that I2C backed device supports SMBUS
- Ensure PWM LEDs are extinguished when disabled, rather than held in a state
- Fix 'output may be truncated' warnings
-----BEGIN PGP SIGNATURE-----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=XYXV
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Core Frameworks:
- Add support for a bunch more colours
New Drivers:
- Add support for Kinetic KTD2026/7 RGB/White LEDs
New Functionality:
- Add support for device to enter HW Controlled Mode to Turris Omnia
LEDs
- Add support for HW Gamma Correction to Turris Omnia LEDs
Fix-ups:
- Apply new __counted_by() annotation to several data structures
containing flexible arrays
- Rid the return value from Platform's .remove() operation
- Use *_cansleep() variants for instances were threads can sleep
- Improve the semantics when setting the brightness
- Generic clean-ups; code reduction, coding style, standard patterns
- Replace strncpy() with strscpy()
- Fix-up / add various documentation
- Re-author the GPIO associated Trigger to use trigger-sources
- Move to using standard APIs and helpers
- Improve error checking
- Stop using static GPIO bases
Bug Fixes:
- Fix Pointer to Enum casing warnings
- Do not pretend that I2C backed device supports SMBUS
- Ensure PWM LEDs are extinguished when disabled, rather than held in
a state
- Fix 'output may be truncated' warnings"
* tag 'leds-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (43 commits)
leds: lp5521: Add an error check in lp5521_post_init_device
leds: gpio: Update headers
leds: gpio: Remove unneeded assignment
leds: gpio: Move temporary variable for struct device to gpio_led_probe()
leds: gpio: Refactor code to use devm_gpiod_get_index_optional()
leds: gpio: Utilise PTR_ERR_OR_ZERO()
leds: gpio: Keep driver firmware interface agnostic
leds: core: Refactor led_update_brightness() to use standard pattern
leds: turris-omnia: Fix brightness setting and trigger activating
leds: sc27xx: Move mutex_init() down
leds: trigger: netdev: Move size check in set_device_name
leds: Add ktd202x driver
dt-bindings: leds: Add Kinetic KTD2026/2027 LED
leds: core: Add more colors from DT bindings to led_colors
dt-bindings: leds: Last color ID is now 14 (LED_COLOR_ID_LIME)
leds: tca6507: Don't use fixed GPIO base
leds: lp3952: Convert to use maple tree register cache
leds: lm392x: Convert to use maple tree register cache
leds: aw200xx: Convert to use maple tree register cache
leds: lm3601x: Convert to use maple tree register cache
...
Instead of checking for the specific error codes, replace
devm_gpiod_get_index() with devm_gpiod_get_index_optional().
In this case we just return all errors to the caller and
simply check for NULL in case if legacy GPIO is being used.
As the result the code is easier to read and maintain.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231016161005.1471768-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
The of.h is used as a proxy to mod_devicetable, replace former by
latter.
The commit 2d6180147e ("leds: gpio: Configure per-LED pin control")
added yet another unneeded OF APIs. Replace with direct use of fwnode.
Altogether this makes driver agnostic to the firmware interface in use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231016161005.1471768-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
The standard conditional pattern is to check for errors first and
bail out if any. Refactor led_update_brightness() accordingly.
While at it, drop unneeded assignment and return 0 unconditionally
on success.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Denis Osterland-Heim <denis.osterland@diehl.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231016153051.1409074-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
I have improperly refactored commits
4d5ed2621c24 ("leds: turris-omnia: Make set_brightness() more efficient")
and
aaf38273cf76 ("leds: turris-omnia: Support HW controlled mode via private trigger")
after Lee requested a change in API semantics of the new functions I
introduced in commit
28350bc0ac77 ("leds: turris-omnia: Do not use SMBUS calls").
Before the change, the function omnia_cmd_write_u8() returned 0 on
success, and afterwards it returned a positive value (number of bytes
written). The latter version was applied, but the following commits did
not properly account for this change.
This results in non-functional LED's .brightness_set_blocking() and
trigger's .activate() methods.
The main reasoning behind the semantics change was that read/write
methods should return the number of read/written bytes on success.
It was pointed to me [1] that this is not always true (for example the
regmap API does not do so), and since the driver never uses this number
of read/written bytes information, I decided to fix this issue by
changing the functions to the original semantics (return 0 on success).
[1] https://lore.kernel.org/linux-gpio/ZQnn+Gi0xVlsGCYA@smile.fi.intel.com/
Fixes: 28350bc0ac77 ("leds: turris-omnia: Do not use SMBUS calls")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20231016141538.30037-1-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Move the mutex_init() to avoid redundant mutex_destroy() calls after
that for each time the probe fails.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231013022010.854367-1-chunyan.zhang@unisoc.com
Signed-off-by: Lee Jones <lee@kernel.org>
GCC 13.2 complains about array subscript 17 is above array bounds of
'char[16]' with IFNAMSIZ set to 16.
The warning is correct but this scenario is impossible.
set_device_name is called by device_name_store (store sysfs entry) and
netdev_trig_activate.
device_name_store already check if size is >= of IFNAMSIZ and return
-EINVAL. (making the warning scenario impossible)
netdev_trig_activate works on already defined interface, where the name
has already been checked and should already follow the condition of
strlen() < IFNAMSIZ.
Aside from the scenario being impossible, set_device_name can be
improved to both mute the warning and make the function safer.
To make it safer, move size check from device_name_store directly to
set_device_name and prevent any out of bounds scenario.
Cc: stable@vger.kernel.org
Fixes: 28a6a2ef18 ("leds: trigger: netdev: refactor code setting device name")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309192035.GTJEEbem-lkp@intel.com/
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20231007131042.15032-1-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
The colors are already part of DT bindings. Make sure the kernel is
able to convert them to strings.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20231008144014.1180334-1-megi@xff.cz
Signed-off-by: Lee Jones <lee@kernel.org>
First of all, the fixed GPIO base is source of troubles and
it doesn't scale. Second, there is no in-kernel user of this
base, so drop it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231002135629.2605462-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-4-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-3-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-2-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-1-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
By providing a GPIO line as "trigger-sources" in the FWNODE
(such as from the device tree) and combining with the
GPIO trigger, we can support a GPIO LED trigger in a natural
way from the hardware description instead of using the
custom sysfs and deprecated global GPIO numberspace.
Example:
gpio: gpio@0 {
compatible "my-gpio";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
#trigger-source-cells = <2>;
};
leds {
compatible = "gpio-leds";
led-my-gpio {
label = "device:blue:myled";
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
default-state = "off";
linux,default-trigger = "gpio";
trigger-sources = <&gpio 1 GPIO_ACTIVE_HIGH>;
};
};
Make this the norm, unmark the driver as broken.
Delete the sysfs handling of GPIOs.
Since GPIO descriptors inherently can describe inversion,
the inversion handling can just be deleted.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230926-gpio-led-trigger-dt-v2-3-e06e458b788e@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Some cleanups:
* Remove the trailing comma in the terminator entry for the OF
table making code robust against (theoretical) misrebases or other
similar things where the new entry goes _after_ the termination without
the compiler noticing.
* Drop a space from terminator entry for ID table.
While at it, move OF/ID table near to the user.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230923171921.53503-3-biju.das.jz@bp.renesas.com
Signed-off-by: Lee Jones <lee@kernel.org>
Convert enum->pointer for data in the match tables, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Replace enum->struct *pca955x_chipdefs for data in the match table.
Simplify the probe() by replacing device_get_match_data() and ID lookup
for retrieving data by i2c_get_match_data().
While at it, add const definition to pca955x_chipdefs[].
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230923171921.53503-2-biju.das.jz@bp.renesas.com
Signed-off-by: Lee Jones <lee@kernel.org>
`strncpy` is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect `dest` to be NUL-terminated due to its use with dev_err.
lp3952_get_label()'s dest argument is priv->leds[i].name:
| acpi_ret = lp3952_get_label(&priv->client->dev, led_name_hdl[i],
| priv->leds[i].name);
... which is then assigned to:
| priv->leds[i].cdev.name = priv->leds[i].name;
... which is used with a format string
| dev_err(&priv->client->dev,
| "couldn't register LED %s\n",
| priv->leds[i].cdev.name);
There is no indication that NUL-padding is required but if it is let's
opt for strscpy_pad.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230922-strncpy-drivers-leds-leds-lp3952-c-v1-1-4941d6f60ca4@google.com
Signed-off-by: Lee Jones <lee@kernel.org>
In order to teach the compiler that 'trig->name' will never be truncated,
we need to tell it that 'cpu' is not negative.
When building with W=1, this fixes the following warnings:
drivers/leds/trigger/ledtrig-cpu.c: In function ‘ledtrig_cpu_init’:
drivers/leds/trigger/ledtrig-cpu.c:155:56: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 5 [-Werror=format-truncation=]
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~
drivers/leds/trigger/ledtrig-cpu.c:155:52: note: directive argument in the range [-2147483648, 7]
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~~~~~~
drivers/leds/trigger/ledtrig-cpu.c:155:17: note: ‘snprintf’ output between 5 and 15 bytes into a destination of size 8
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8f88731d05 ("led-triggers: create a trigger for CPU activity")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/3f4be7a99933cf8566e630da54f6ab913caac432.1695453322.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
Disabling a PWM (i.e. calling pwm_apply_state with .enabled = false)
gives no guarantees what the PWM output does. It might freeze where it
currently is, or go in a High-Z state or drive the active or inactive
state, it might even continue to toggle.
To ensure that the LED gets really disabled, don't disable the PWM even
when .duty_cycle is zero.
This fixes disabling a leds-pwm LED on i.MX28. The PWM on this SoC is
one of those that freezes its output on disable, so if you disable an
LED that is full on, it stays on. If you disable a LED with half
brightness it goes off in 50% of the cases and full on in the other 50%.
Fixes: 41c42ff5db ("leds: simple driver for pwm driven LEDs")
Reported-by: Rogan Dawes <rogan@dawes.za.net>
Reported-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230922192834.1695727-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
If the MCU on Turris Omnia is running newer firmware versions, the LED
controller supports RGB gamma correction (and enables it by default for
newer boards).
Determine whether the gamma correction setting feature is supported and
add the ability to set it via sysfs attribute file.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-5-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for enabling MCU controlled mode of the Turris Omnia LEDs
via a LED private trigger called "omnia-mcu". Recall that private LED
triggers will only be listed in the sysfs trigger file for LEDs that
support them (currently there is no user of this mechanism).
When in MCU controlled mode, the user can still set LED color, but the
blinking is done by MCU, which does different things for different LEDs:
- WAN LED is blinked according to the LED[0] pin of the WAN PHY
- LAN LEDs are blinked according to the LED[0] output of the
corresponding port of the LAN switch
- PCIe LEDs are blinked according to the logical OR of the MiniPCIe port
LED pins
In the future I want to make the netdev trigger to transparently offload
the blinking to the HW if user sets compatible settings for the netdev
trigger (for LEDs associated with network devices).
There was some work on this already, and hopefully we will be able to
complete it sometime, but for now there are still multiple blockers for
this, and even if there weren't, we still would not be able to configure
HW controlled mode for the LEDs associated with MiniPCIe ports.
In the meantime let's support HW controlled mode via the private LED
trigger mechanism. If, in the future, we manage to complete the netdev
trigger offloading, we can still keep this private trigger for backwards
compatibility, if needed.
We also set "omnia-mcu" to cdev->default_trigger, so that the MCU keeps
control until the user first wants to take over it. If a different
default trigger is specified in device-tree via the
'linux,default-trigger' property, LED class will overwrite
cdev->default_trigger, and so the DT property will be respected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-4-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Implement caching of the LED color and state values that are sent to MCU
in order to make the set_brightness() operation more efficient by
avoiding I2C transactions which are not needed.
On Turris Omnia's MCU, which acts as the RGB LED controller, each LED
has a RGB color, and a ON/OFF state, which are configurable via I2C
commands CMD_LED_COLOR and CMD_LED_STATE.
The CMD_LED_COLOR command sends 5 bytes and the CMD_LED_STATE command 2
bytes over the I2C bus, which operates at 100 kHz. With I2C overhead
this allows ~1670 color changing commands and ~3200 state changing
commands per second (or around 1000 color + state changes per second).
This may seem more than enough, but the issue is that the I2C bus is
shared with another peripheral, the MCU. The MCU exposes an interrupt
interface, and it can trigger hundreds of interrupts per second. Each
time, we need to read the interrupt state register over this I2C bus.
Whenever we are sending a LED color/state changing command, the
interrupt reading is waiting.
Currently, every time LED brightness or LED multi intensity is changed,
we send a CMD_LED_STATE command, and if the computed color (brightness
adjusted multi_intensity) is non-zero, we also send a CMD_LED_COLOR
command.
Consider for example the situation when we have a netdev trigger enabled
for a LED. The netdev trigger does not change the LED color, only the
brightness (either to 0 or to currently configured brightness), and so
there is no need to send the CMD_LED_COLOR command. But each change of
brightness to 0 sends one CMD_LED_STATE command, and each change of
brightness to max_brightness sends one CMD_LED_STATE command and one
CMD_LED_COLOR command:
set_brightness(0) -> CMD_LED_STATE
set_brightness(255) -> CMD_LED_STATE + CMD_LED_COLOR
(unnecessary)
We can avoid the unnecessary I2C transactions if we cache the values of
state and color that are sent to the controller. If the color does not
change from the one previously sent, there is no need to do the
CMD_LED_COLOR I2C transaction, and if the state does not change, there
is no need to do the CMD_LED_STATE transaction.
Because we need to make sure that our cached values are consistent with
the controller state, add explicit setting of the LED color to white at
probe time (this is the default setting when MCU resets, but does not
necessarily need to be the case, for example if U-Boot played with the
LED colors).
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-3-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The leds-turris-omnia driver uses three function for I2C access:
- i2c_smbus_write_byte_data() and i2c_smbus_read_byte_data(), which
cause an emulated SMBUS transfer,
- i2c_master_send(), which causes an ordinary I2C transfer.
The Turris Omnia MCU LED controller is not semantically SMBUS, it
operates as a simple I2C bus. It does not implement any of the SMBUS
specific features, like PEC, or procedure calls, or anything. Moreover
the I2C controller driver also does not implement SMBUS, and so the
emulated SMBUS procedure from drivers/i2c/i2c-core-smbus.c is used for
the SMBUS calls, which gives an unnecessary overhead.
When I first wrote the driver, I was unaware of these facts, and I
simply used the first function that worked.
Drop the I2C SMBUS calls and instead use simple I2C transfers.
Fixes: 089381b27a ("leds: initial support for Turris Omnia LEDs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-2-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Use gpiod_set_value_cansleep in the init_device function. Without this
change, the driver may print a warning if the LP55xx enable pin is
connected to a GPIO chip which can sleep (e.g. a GPIO expander):
WARNING: CPU: 0 PID: 2719 at drivers/gpio/gpiolib.c:3051 gpiod_set_value+0x64/0xbc
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Link: https://lore.kernel.org/r/20230918143238.75600-1-eichest@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct mt6370_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915201051.never.429-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct mt6360_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915201020.never.433-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
All platform drivers below drivers/leds/ unconditionally return zero in
their remove callback and so can be converted trivially to the variant
returning void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230917130947.1122198-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Make simatic_ipc_leds_gpio_remove() return void instead of returning
zero unconditionally. After that the three remove callbacks that use
this function were trivial to convert to return void, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230916164516.1063380-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct lpg_led.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915201059.never.086-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct lm3697.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915201010.never.399-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct gpio_leds_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915201003.never.148-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct el15203000.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915200955.never.871-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct cr0014114.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915200948.never.728-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct aw200xx.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915200938.never.767-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
When building with clang 18 I see the following warning:
| drivers/leds/leds-pca955x.c:487:15: warning: cast to smaller integer
| type 'enum pca955x_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
| 487 | chip_type = (enum pca955x_type)md;
This is due to the fact that `md` is a void* while `enum pca995x_type` has the
size of an int.
Add uintptr_t cast to silence clang warning while also keeping enum cast
for readability and consistency with other `chip_type` assignment just a
few lines below:
| chip_type = (enum pca955x_type)id->driver_data;
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://github.com/ClangBuiltLinux/linux/issues/1910
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230816-void-drivers-leds-leds-pca955x-v1-1-2967e4c1bdcc@google.com
Signed-off-by: Lee Jones <lee@kernel.org>
Instead of requiring each driver to care for assigning the owner member
of struct pwm_ops, handle that implicitly using a macro. Note that the
owner member has to be moved to struct pwm_chip, as the ops structure
usually lives in read-only memory and so cannot be modified.
The upside is that new low level drivers cannot forget the assignment and
save one line each. The pwm-crc driver didn't assign .owner, that's not
a problem in practice though as the driver cannot be compiled as a
module.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # Intel LPSS
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> # pwm-{bcm,brcm}*.c
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> # sun4i
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> # pwm-visconti
Acked-by: Heiko Stuebner <heiko@sntech.de> # pwm-rockchip
Acked-by: Michael Walle <michael@walle.cc> # pwm-sl28cpld
Acked-by: Neil Armstrong <neil.armstrong@linaro.org> # pwm-meson
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230804142707.412137-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Commit c3f853184b ("leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that
is always false") fixed a no-op BUG_ON. This turned out to cause a
regression, since some in-tree device-tree files already use
LED_COLOR_ID_MULTI.
Drop the BUG_ON altogether.
Fixes: c3f853184b ("leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that is always false")
Reported-by: Da Xue <da@libre.computer>
Closes: https://lore.kernel.org/linux-leds/ZQLelWcNjjp2xndY@duo.ucw.cz/T/
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918140724.18634-1-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
- Add new framework to support Group Multi-Color (GMC) LEDs
- Offer an 'optional' API for non-essential LEDs
- Support obtaining 'max brightness' values from Device Tree
- Provide new led_classdev member 'color' (settable via DT and SYFS)
- Stop TTY Trigger from using the old LED_ON constraints
- Statically allocate leds_class
- New Drivers
- Add support for NXP PCA995x I2C Constant Current LED Driver
- New Device Support
- Add support for Siemens Simatic IPC BX-21 to Simatic IPC
- Fix-ups
- Some dependency / Kconfig tweaking
- Move final probe() functions back over from .probe_new()
- Simplify obtaining resources (memory, device data) using unified API helpers
- Bunch of Device Tree additions, conversions and adaptions
- Fix trivial styling issues; comments
- Ensure correct includes are present and remove some that are not required
- Omit the use of redundant casts and if relevant replace with better ones
- Use purpose-built APIs for various actions; sysfs_emit(), module_led_trigger()
- Remove a bunch of superfluous locking
- Bug Fixes
- Ensure error codes are correctly propagated back up the call chain
- Fix incorrect error values from being returned (missing '-')
- Ensure get'ed resources are put'ed to prevent leaks
- Use correct class when exporting module resources
- Fixing rounding (or lack there of) issues
- Fix 'always false' LED_COLOR_ID_MULTI BUG() check
-----BEGIN PGP SIGNATURE-----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=wNmv
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Core Frameworks:
- Add new framework to support Group Multi-Color (GMC) LEDs
- Offer an 'optional' API for non-essential LEDs
- Support obtaining 'max brightness' values from Device Tree
- Provide new led_classdev member 'color' (settable via DT and SYFS)
- Stop TTY Trigger from using the old LED_ON constraints
- Statically allocate leds_class
New Drivers:
- Add support for NXP PCA995x I2C Constant Current LED Driver
New Device Support:
- Add support for Siemens Simatic IPC BX-21 to Simatic IPC
Fix-ups:
- Some dependency / Kconfig tweaking
- Move final probe() functions back over from .probe_new()
- Simplify obtaining resources (memory, device data) using unified
API helpers
- Bunch of Device Tree additions, conversions and adaptions
- Fix trivial styling issues; comments
- Ensure correct includes are present and remove some that are not
required
- Omit the use of redundant casts and if relevant replace with better
ones
- Use purpose-built APIs for various actions; sysfs_emit(),
module_led_trigger()
- Remove a bunch of superfluous locking
Bug Fixes:
- Ensure error codes are correctly propagated back up the call chain
- Fix incorrect error values from being returned (missing '-')
- Ensure get'ed resources are put'ed to prevent leaks
- Use correct class when exporting module resources
- Fixing rounding (or lack there of) issues
- Fix 'always false' LED_COLOR_ID_MULTI BUG() check"
* tag 'leds-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (40 commits)
leds: aw2013: Enable pull-up supply for interrupt and I2C
dt-bindings: leds: Document pull-up supply for interrupt and I2C
dt-bindings: leds: aw2013: Document interrupt
leds: uleds: Use module_misc_device macro to simplify the code
leds: trigger: netdev: Use module_led_trigger macro to simplify the code
dt-bindings: leds: Fix reference to definition of default-state
leds: turris-omnia: Drop unnecessary mutex locking
leds: turris-omnia: Use sysfs_emit() instead of sprintf()
leds: Make leds_class a static const structure
leds: Remove redundant of_match_ptr()
dt-bindings: leds: Add gpio-line-names to PCA9532 GPIO
leds: trigger: tty: Do not use LED_ON/OFF constants, use led_blink_set_oneshot instead
dt-bindings: leds: rohm,bd71828: Drop select:false
leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that is always false
leds: multicolor: Use rounded division when calculating color components
leds: rgb: Add a multicolor LED driver to group monochromatic LEDs
dt-bindings: leds: Add binding for a multicolor group of LEDs
leds: class: Store the color index in struct led_classdev
leds: Provide devm_of_led_get_optional()
leds: pca995x: Fix MODULE_DEVICE_TABLE for OF
...
Highlights:
- hp-bioscfg: New firmware-attributes driver for changing BIOS settings
from within Linux
- asus-wmi: Add charger mode, middle fan and eGPU settings support
- ideapad: Support keyboard backlight control on more models
- mellanox: Support for new models
- sel-3350: New LED and power-supply driver for this industrial mainboard
- simatic-ipc: Add RTC battery monitor and various new models support
- Miscellaneous other cleanups / fixes
The following is an automated git shortlog grouped by driver:
Add SEL-3350 platform driver:
- Add SEL-3350 platform driver
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
MAINTAINERS:
- Add entries for Siemens IPC modules
Merge remote-tracking branch 'intel-speed-select/intel-sst' into review-hans:
- Merge remote-tracking branch 'intel-speed-select/intel-sst' into review-hans
Merge remote-tracking branch 'pdx86/fixes' into pdx86/for-next:
- Merge remote-tracking branch 'pdx86/fixes' into pdx86/for-next
Merge remote-tracking branch 'pdx86/platform-drivers-x86-simatic-ipc' into review-hans:
- Merge remote-tracking branch 'pdx86/platform-drivers-x86-simatic-ipc' into review-hans
Merge tag 'ib-pdx86-simatic-v6.6' into review-hans:
- Merge tag 'ib-pdx86-simatic-v6.6' into review-hans
Merge tag 'ib-pdx86-simatic-v6.6-2' into review-hans:
- Merge tag 'ib-pdx86-simatic-v6.6-2' into review-hans
Move all simatic ipc drivers to the subdirectory siemens:
- Move all simatic ipc drivers to the subdirectory siemens
asus-wmi:
- corrections to egpu safety check
- Fix support for showing middle fan RPM
- expose dGPU and CPU tunables for ROG
- support setting mini-LED mode
- add safety checks to gpu switching
- don't allow eGPU switching if eGPU not connected
- add WMI method to show if egpu connected
- support middle fan custom curves
- add support for showing middle fan RPM
- add support for showing charger mode
dell-sysman:
- Fix reference leak
doc:
- TPMI: Add debugfs documentation
hp-bioscfg:
- Update steps order list elements are evaluated
- Use kmemdup() to replace kmalloc + memcpy
- Remove duplicate use of variable in inner loop
- Change how password encoding size is evaluated
- Change how enum possible values size is evaluated
- Change how order list size is evaluated
- Change how prerequisites size is evaluated
- Replace the word HACK from source code
- Fix uninitialized variable errors
- Fix memory leaks in attribute packages
- fix error reporting in hp_add_other_attributes()
- prevent a small buffer overflow
- fix a signedness bug in hp_wmi_perform_query()
- MAINTAINERS
- Makefile
- surestart-attributes
- string-attributes
- spmobj-attributes
- passwdobj-attributes
- order-list-attributes
- int-attributes
- enum-attributes
- biosattr-interface
- bioscfg
- bioscfg-h
- Documentation
ideapad-laptop:
- Add support for keyboard backlights using KBLC ACPI symbol
leds:
- simatic-ipc-leds: default config switch to platform switch
mlx-platform:
- Add dependency on PCI to Kconfig
mlxbf-bootctl:
- Support sysfs entries for MFG fields
- Support setting the ARM boot state to "OS up"
- Support the large icmc write/read
p2sb:
- Make the Kconfig symbol hidden
platform:
- mellanox: nvsw-sn2201: change fans i2c busses.
- mellanox: mlxreg-hotplug: Extend condition for notification callback processing
- mellanox: Add initial support for PCIe based programming logic device
- mellanox: mlx-platform: Get interrupt line through ACPI
- mellanox: mlx-platform: Introduce ACPI init flow
- mellanox: mlx-platform: Prepare driver to allow probing through ACPI infrastructure
- mellanox: mlx-platform: Add reset callback
- mellanox: Cosmetic changes
- mellanox: mlx-platform: Modify power off callback
- mellanox: mlx-platform: add support for additional CPLD
- mellanox: mlx-platform: Add reset cause attribute
- mellanox: mlx-platform: Modify health and power hotplug action
- mellanox: Modify reset causes description
- mellanox: Add field upgrade capability register
- mellanox: Add new attributes
- Explicitly include correct DT includes
platform/x86/amd/pmc:
- Fix build error with randconfig
- Move PMC driver to separate directory
platform/x86/amd/pmf:
- Fix a missing cleanup path
- Use str_on_off() helper
platform/x86/intel/tpmi:
- Add debugfs interface
- Read feature control status
platform/x86/siemens:
- simatic-ipc-batt: fix logical error for BX-59A
- simatic-ipc: fix logical error for BX-59A
- simatic-ipc-batt: fix wrong pointer pass to PTR_ERR()
- simatic-ipc-batt: add support for module BX-59A
- simatic-ipc: add new models BX-56A/BX-59A
- Kconfig: adjust help text
- simatic-ipc-batt: fix bat reading in BX_21A
simatic-ipc:
- use extra module loading for watchdog
- add auto-loading of hwmon modules
- add another model
- drop PCI runtime depends and header
- add CMOS battery monitoring
- add another model BX-21A
system76:
- Handle new KBLED ACPI methods
thinkpad_acpi:
- Switch to memdup_user_nul() helper
- use lockdep annotations
- take mutex for hotkey_mask_{set,get}
tools/power/x86/intel-speed-select:
- v1.17 release
- Change mem-frequency display name
- Prevent CPU 0 offline
- Error on CPU count exceed in request
- Support more than 8 sockets.
- Fix CPU count display
watchdog:
- simatic: Use idiomatic selection of P2SB
- simatic: add PCI dependency
- make Siemens Simatic watchdog driver default on platform
- simatic-ipc-wdt: make IO region access of one model muxed
wmi-bmof:
- Update MAINTAINERS entry
- Simplify read_bmof()
- Use device_create_bin_file()
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmTx720UHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9wHYggAgPpl4tcbqUK7S/fwVP2SzBKI+eF3
5PjO7PlMEVzyKyjHdkqoV8miMffWAGVPE+LV33Uifs5WTFjHRq2fq/Esvj9mAstG
1fCoHJ442xYkwNCUT1CCP7VsmcvV5eFXBjBantvwmIs8TyknGHwtq1h+d95evp4n
2uyQlRMmrWh/+8fjD8x5V35T0tky+4a4EX2WNLul13LlHCybGT/F2Kq456WdthjJ
zTQSL+qAMWmAiQKSEmhI3bRnFYPdpTetjiNSTlQczch8Y4qV3mJQlnkyDPX7SM9w
M2uZ4W39Ptxihx0ks/MIcuA4yrTfUX8BnhMTD29ZYCKHS7xBqW8YC5HQug==
=GaQL
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- hp-bioscfg: New firmware-attributes driver for changing BIOS settings
from within Linux
- asus-wmi: Add charger mode, middle fan and eGPU settings support
- ideapad: Support keyboard backlight control on more models
- mellanox: Support for new models
- sel-3350: New LED and power-supply driver for this industrial
mainboard
- simatic-ipc: Add RTC battery monitor and various new models support
- miscellaneous other cleanups / fixes
* tag 'platform-drivers-x86-v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (101 commits)
platform/x86: asus-wmi: corrections to egpu safety check
platform/x86: mlx-platform: Add dependency on PCI to Kconfig
platform/x86: ideapad-laptop: Add support for keyboard backlights using KBLC ACPI symbol
platform/x86/amd/pmc: Fix build error with randconfig
platform/x86/amd/pmf: Fix a missing cleanup path
watchdog: simatic: Use idiomatic selection of P2SB
platform/x86: p2sb: Make the Kconfig symbol hidden
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform: mellanox: nvsw-sn2201: change fans i2c busses.
platform: mellanox: mlxreg-hotplug: Extend condition for notification callback processing
platform: mellanox: Add initial support for PCIe based programming logic device
platform: mellanox: mlx-platform: Get interrupt line through ACPI
platform: mellanox: mlx-platform: Introduce ACPI init flow
platform: mellanox: mlx-platform: Prepare driver to allow probing through ACPI infrastructure
platform: mellanox: mlx-platform: Add reset callback
platform: mellanox: Cosmetic changes
platform: mellanox: mlx-platform: Modify power off callback
platform: mellanox: mlx-platform: add support for additional CPLD
platform: mellanox: mlx-platform: Add reset cause attribute
platform: mellanox: mlx-platform: Modify health and power hotplug action
...
Commit b655892ffd ("leds: trigger: netdev: expose hw_control status
via sysfs") exposed to sysfs the flag that tells whether the LED trigger
is offloaded to hardware, under the name "hw_control", since that is the
name under which this setting is called in the code.
Everywhere else in kernel when some work that is normally done in
software can be made to be done by hardware instead, we use the word
"offloading" to describe this, e.g. "LED blinking is offloaded to
hardware".
Normally renaming sysfs entries is a no-go because of backwards
compatibility. But since this patch was not yet released in a stable
kernel, I think it is still possible to rename it, if there is
consensus.
Fixes: b655892ffd ("leds: trigger: netdev: expose hw_control status via sysfs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230821121453.30203-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Request and enable the "vio" regulator that represents the power supply
that is needed for the pull-up resistors of the interrupt and I2C lines
of AW2013. While this regulator is not wired directly to the AW2013
chip it is best managed as part of the AW2013 driver since it decides
when AW2013 is powered on and when the interrupt is enabled or
disabled.
This regulator should always be enabled in conjunction with the main
VCC power supply, so use the bulk regulator functions to enable both
at the same time.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
[rewrite commit message based on discussion]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20230815-aw2013-vio-v3-3-2505296b0856@gerhold.net
Signed-off-by: Lee Jones <lee@kernel.org>
Use the module_misc_device macro to simplify the code, which is the
same as declaring with module_init() and module_exit().
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815075944.1089298-3-lizetao1@huawei.com
Signed-off-by: Lee Jones <lee@kernel.org>
Use the module_led_trigger macro to simplify the code, which is the
same as declaring with module_init() and module_exit().
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815075944.1089298-2-lizetao1@huawei.com
Signed-off-by: Lee Jones <lee@kernel.org>
Do not lock driver mutex in the global LED panel brightness sysfs
accessors brightness_show() and brightness_store().
The mutex locking is unnecessary here. The I2C transfers are guarded by
I2C core locking mechanism, and the LED commands itself do not interfere
with other commands.
Fixes: 089381b27a ("leds: initial support for Turris Omnia LEDs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230802160748.11208-2-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Use the dedicated sysfs_emit() function instead of sprintf() in sysfs
attribute accessor brightness_show().
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230802160748.11208-4-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Now that the driver core allows for struct class to be in read-only
memory, move the leds_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230810174905.7997-1-ivan.orlov0322@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here. We remove both CONFIG_OF and of_match_ptr() here.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Link: https://lore.kernel.org/r/20230808111108.24262-1-wangzhu9@huawei.com
Signed-off-by: Lee Jones <lee@kernel.org>
The tty LED trigger uses the obsolete LED_ON & LED_OFF constants when
setting LED brightness. This is bad because the LED_ON constant is equal
to 1, and so when activating the tty LED trigger on a LED class device
with max_brightness greater than 1, the LED is dimmer than it can be
(when max_brightness is 255, the LED is very dimm indeed; some devices
translate 1/255 to 0, so the LED is OFF all the time).
Instead of directly setting brightness to a specific value, use the
led_blink_set_oneshot() function from LED core to configure the blink.
This function takes the current configured brightness as blink
brightness if not zero, and max brightness otherwise.
This also changes the behavior of the TTY LED trigger. Previously if
rx/tx stats kept changing, the LED was ON all the time they kept
changing. With this patch the LED will blink on TTY activity.
Fixes: fd4a641ac8 ("leds: trigger: implement a tty trigger")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230802090753.13611-1-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
At the time we call
BUG_ON(props.color == LED_COLOR_ID_MULTI);
the props variable is still initialized to zero.
Call the BUG_ON only after we parse fwnode into props.
Fixes: 77dce3a22e ("leds: disallow /sys/class/leds/*:multi:* for now")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230801151623.30387-1-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Given channel intensity, LED brightness and max LED brightness, the
multicolor LED framework helper led_mc_calc_color_components() computes
the color channel brightness as
chan_brightness = brightness * chan_intensity / max_brightness
Consider the situation when (brightness, intensity, max_brightness) is
for example (16, 15, 255), then chan_brightness is computed to 0
although the fractional divison would give 0.94, which should be rounded
to 1.
Use DIV_ROUND_CLOSEST here for the division to give more realistic
component computation:
chan_brightness = DIV_ROUND_CLOSEST(brightness * chan_intensity,
max_brightness)
Fixes: 55d5d3b46b ("leds: multicolor: Introduce a multicolor class definition")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230801124931.8661-1-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Grouping multiple monochrome LEDs into a multicolor LED device has a few
benefits over handling the group in user-space:
- The state of the LEDs relative to each other is consistent. In other
words, if 2 threads competes to set the LED to green and red, the
end-result cannot be black or yellow.
- The multicolor LED as a whole can be driven through the sysfs LED
interface.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230728153731.3742339-5-jjhiblot@traphandler.com
Signed-off-by: Lee Jones <lee@kernel.org>
Store the color of the LED so that it is not lost after the LED's
name has been composed. This color information can then be exposed to
the user space or used by the LED consumer.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Link: https://lore.kernel.org/r/20230728153731.3742339-3-jjhiblot@traphandler.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add an optional variant of devm_of_led_get(). It behaves the same as
devm_of_led_get() except where the LED doesn't exist. In this case,
instead of returning -ENOENT, the function returns NULL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230728153731.3742339-2-jjhiblot@traphandler.com
Signed-off-by: Lee Jones <lee@kernel.org>
Fix copy-paste error in MODULE_DEVICE_TABLE() for the OF table,
use the 'of' first parameter instead of duplicate 'i2c'.
Fixes: ee4e80b296 ("leds: pca995x: Add support for PCA995X chips")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230809125314.531806-1-marex@denx.de
Signed-off-by: Lee Jones <lee@kernel.org>
Ensure that the offloading of blinking is stopped when the trigger is
deactivated. Calling led_set_brightness() is documented as stopping
offload and setting the LED to a constant brightness.
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230808210436.838995-5-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the netdev trigger is activates, it tries to determine what
device the LED blinks for, and what the current blink mode is.
The documentation for hw_control_get() says:
* Return 0 on success, a negative error number on failing parsing the
* initial mode. Error from this function is NOT FATAL as the device
* may be in a not supported initial state by the attached LED trigger.
*/
For the Marvell PHY and the Armada 370-rd board, the initial LED blink
mode is not supported by the trigger, so it returns an error. This
resulted in not getting the device the LED is blinking for. As a
result, the device is unknown and offloaded is never performed.
Change to condition to always get the device if offloading is
supported, and reduce the scope of testing for an error from
hw_control_get() to skip setting trigger internal state if there is an
error.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230808210436.838995-2-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a user did choose to enable Siemens Simatic platform support they
likely want the LED drivers to be enabled without having to flip more
config switches. So we make the LED drivers config switch default to
the platform driver switches value.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230719153518.13073-3-henning.schild@siemens.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Since commit f9a8ee8c8b ("pwm: Always allocate PWM chip base ID
dynamically") there is no effect any more for assigning this variable. See
pwmchip_add() which unconditionally overwrites this member.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230728065739.580281-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174651.4058753-1-robh@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Symbol ARCH_BCM4908 has been merged/removed without updating leds
Kconfig.
Fixes: dd5c672d7c ("arm64: bcmbca: Merge ARCH_BCM4908 to ARCH_BCMBCA")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230714063214.3791-1-zajec5@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
This is used for the Siemens Simatic IPC BX-21A, which has its LEDs
connected to GPIOs provided by the Intel Elkhart Lake pinctrl driver.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Link: https://lore.kernel.org/r/20230713115639.16419-3-henning.schild@siemens.com
Signed-off-by: Lee Jones <lee@kernel.org>
The PCA995x chips are I2C controlled LED drivers. Each chip has
up to 16 outputs, each one with an individual 8-bit resolution
PWM for brightness control.
Signed-off-by: Isai Gaspar <isaiezequiel.gaspar@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Basically rewrite the driver
Link: https://lore.kernel.org/r/20230713163516.21644-2-marex@denx.de
Signed-off-by: Lee Jones <lee@kernel.org>
Negative -EINVAL was intended, not positive EINVAL. Fix it.
Fixes: 95138e0127 ("leds: pwm: Make error handling more robust")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/a33b981a-b2c4-4dc2-b00a-626a090d2f11@moroto.mountain
Signed-off-by: Lee Jones <lee@kernel.org>
Normally, the maximum brightness is determined by the hardware, and this
property is not required. This property is used to set a software limit.
It could happen that an LED is made so bright that it gets damaged or
causes damage due to restrictions in a specific system, such as mounting
conditions.
Note that this flag is mainly used for PWM-LEDs, where it is not possible
to map brightness to current. Drivers for other controllers should use
led-max-microamp.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Link: https://lore.kernel.org/r/20230703130313.548519-3-astrid.rost@axis.com
Signed-off-by: Lee Jones <lee@kernel.org>
A recent rework accidentally lost the dependency on LEDS_CLASS, which
leads to a link error when LED support is disbled:
x86_64-linux-ld: drivers/leds/simple/simatic-ipc-leds.o: in function `simatic_ipc_leds_probe':
simatic-ipc-leds.c:(.text+0x10c): undefined reference to `devm_led_classdev_register_ext'
Add back the dependency that was there originally.
Fixes: a6c80bec3c ("leds: simatic-ipc-leds-gpio: Add GPIO version of Siemens driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230623152233.2246285-1-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
- New Device Support
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
- New Functionality
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
- Fix-ups
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
- Bug Fixes
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues
-----BEGIN PGP SIGNATURE-----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=9kd5
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
New Device Support:
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
New Functionality:
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
Fix-ups:
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
Bug Fixes:
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues"
* tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (53 commits)
leds: leds-mt6323: Adjust return/parameter types in wled get/set callbacks
leds: sgm3140: Add richtek,rt5033-led compatible
dt-bindings: leds: sgm3140: Document richtek,rt5033 compatible
dt-bindings: backlight: kinetic,ktz8866: Add missing type for "current-num-sinks"
dt-bindings: leds: Drop unneeded quotes
leds: Fix config reference for AW200xx driver
leds: leds-mt6323: Add support for WLEDs and MT6332
leds: leds-mt6323: Add support for MT6331 leds
leds: leds-mt6323: Open code and drop MT6323_CAL_HW_DUTY macro
leds: leds-mt6323: Drop MT6323_ prefix from macros and defines
leds: leds-mt6323: Specify registers and specs in platform data
dt-bindings: leds: leds-mt6323: Document mt6332 compatible
dt-bindings: leds: leds-mt6323: Document mt6331 compatible
leds: simatic-ipc-leds-gpio: Introduce more Kconfig switches
leds: simatic-ipc-leds-gpio: Split up into multiple drivers
leds: simatic-ipc-leds-gpio: Move two extra gpio pins into another table
leds: simatic-ipc-leds-gpio: Add terminating entries to gpio tables
leds: flash: leds-qcom-flash: Fix an unsigned comparison which can never be negative
leds: cht-wcove: Remove unneeded semicolon
leds: cht-wcove: Fix an unsigned comparison which can never be negative
...
Clang's kernel Control Flow Integrity (kCFI) is a compiler-based
security mitigation that ensures the target of an indirect function call
matches the expected type of the call and trapping if they do not match
exactly. The warning -Wincompatible-function-pointer-types-strict aims
to catch these issues at compile time, which reveals:
drivers/leds/leds-mt6323.c:598:49: error: incompatible function pointer types assigning to 'int (*)(struct led_classdev *, enum led_brightness)' from 'int (struct led_classdev *, unsigned int)' [-Werror,-Wincompatible-function-pointer-types-strict]
598 | leds->led[reg]->cdev.brightness_set_blocking =
| ^
599 | mt6323_wled_set_brightness;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/leds/leds-mt6323.c:600:40: error: incompatible function pointer types assigning to 'enum led_brightness (*)(struct led_classdev *)' from 'unsigned int (struct led_classdev *)' [-Werror,-Wincompatible-function-pointer-types-strict]
600 | leds->led[reg]->cdev.brightness_get =
| ^
601 | mt6323_get_wled_brightness;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
2 errors generated.
While 'unsigned int' is ABI compatible with 'enum led_brightness' (hence
no warning from -Wincompatible-function-pointer-types) and the callers
of these callbacks use/pass the values as 'unsigned int', the mismatch
between the prototype and the called function will trip kCFI at runtime.
Change the types in the implementations to match the prototypes, clearing
up the warning and avoiding kCFI failures.
Fixes: 9bb0a9e062 ("leds: leds-mt6323: Add support for WLEDs and MT6332")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230622-mt6323-wled-wincompatible-function-pointer-types-strict-v1-1-6ad256f220e8@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Expose hw_control status via sysfs for the netdev trigger to give
userspace better understanding of the current state of the trigger and
the LED.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add additional modes for specific link duplex. Use ethtool APIs to get the
current link duplex and enable the LED accordingly. Under netdev event
handler the rtnl lock is already held and is not needed to be set to
access ethtool APIs.
This is especially useful for PHY and Switch that supports LEDs hw
control for specific link duplex.
Add additional modes:
- half_duplex: Turn on LED when link is half duplex
- full_duplex: Turn on LED when link is full duplex
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add additional modes for specific link speed. Use ethtool APIs to get the
current link speed and enable the LED accordingly. Under netdev event
handler the rtnl lock is already held and is not needed to be set to
access ethtool APIs.
This is especially useful for PHY and Switch that supports LEDs hw
control for specific link speed. (example scenario a PHY that have 2 LED
connected one green and one orange where the green is turned on with
1000mbps speed and orange is turned on with 10mpbs speed)
On mode set from sysfs we check if we have enabled split link speed mode
and reject enabling generic link mode to prevent wrong and redundant
configuration.
Rework logic on the set baseline state to support these new modes to
select if we need to turn on or off the LED.
Add additional modes:
- link_10: Turn on LED when link speed is 10mbps
- link_100: Turn on LED when link speed is 100mbps
- link_1000: Turn on LED when link speed is 1000mbps
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 36a87f371b ("leds: Add AW20xx driver") adds config LEDS_AW200XX
in drivers/leds/Kconfig, but then in drivers/leds/Makefile accidently
refers to CONFIG_LEDS_W200XX; note the missing A!
This typo makes it impossible to add the driver to a kernel build.
Fix this wrong config reference.
Fixes: 36a87f371b ("leds: Add AW20xx driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230609100233.4111-1-lukas.bulwahn@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
The qca8k_cled_hw_control_get() function which implements ->hw_control_get
sets the appropriate bits but does not clear them. This leads to an
uninitialized variable bug. Fix this by setting mode to zero at the
start.
Fixes: e0256648c8 ("net: dsa: qca8k: implement hw_control ops")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic code to turn on and off WLEDs and wire up MT6332 support
to take advantage of it.
This is a simple approach due to the aforementioned PMIC supporting
only on/off status so, at the time of writing, it is impossible for me
to validate more advanced functionality due to lack of hardware.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230601110813.2373764-9-angelogioacchino.delregno@collabora.com
Add the register offsets for MT6331. The hwspec is the same as MT6323.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230601110813.2373764-8-angelogioacchino.delregno@collabora.com
There is only one instance of using this macro and it's anyway not
simplifying the flow, or increasing the readability of this driver.
Drop this macro by open coding it in mt6323_led_set_blink().
No functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230601110813.2373764-7-angelogioacchino.delregno@collabora.com
This renames all definitions and macros to drop the MT6323_ prefix,
since it is now possible to easily add support to more PMICs in
this driver.
While at it, also fix related formatting where possible.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230601110813.2373764-6-angelogioacchino.delregno@collabora.com
In order to enhance the flexibility of this driver and let it support
more than just one MediaTek LEDs IP for more than just one PMIC,
add platform data structure specifying the register offsets and
data that commonly varies between different IPs.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230601110813.2373764-5-angelogioacchino.delregno@collabora.com
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/sch_taprio.c
d636fc5dd6 ("net: sched: add rcu annotations around qdisc->qdisc_sleeping")
dced11ef84 ("net/sched: taprio: don't overwrite "sch" variable in taprio_dump_class_stats()")
net/ipv4/sysctl_net_ipv4.c
e209fee411 ("net/ipv4: ping_group_range: allow GID from 2147483648 to 4294967294")
ccce324dab ("tcp: make the first N SYN RTO backoffs linear")
https://lore.kernel.org/all/20230605100816.08d41a7b@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To describe the dependency chain better and allow for potential
fine-grained config tuning, introduce Kconfig switch for the individual
GPIO based drivers.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230524124628.32295-5-henning.schild@siemens.com
In order to clearly describe the dependencies between the GPIO
controller drivers and the users the driver is split up into a core,
two drivers and a common header.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230524124628.32295-4-henning.schild@siemens.com
There are two special pins needed to init the LEDs. We used to have them
at the end of the gpiod_lookup table to give to "leds-gpio". A cleaner
way is to have a dedicated table for the special pins.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230524124628.32295-3-henning.schild@siemens.com
The entries do not seem to be stricly needed when the number of entries
is given via the number of LEDs. But adding them is a safeguard should
anyone ever iterate over the tables to their end, it also gets us in
line with other drivers that register "leds-gpio" tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230524124628.32295-2-henning.schild@siemens.com
The variable 'count' is defined as unsigned type, so the following if
statement is invalid, we can modify the type of count to int.
if (count <= 0) {
dev_err(dev, "No led-sources specified\n");
return -ENODEV;
}
./drivers/leds/flash/leds-qcom-flash.c:546:5-10: WARNING: Unsigned expression compared with zero: count <= 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5344
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230531053559.5702-1-jiapeng.chong@linux.alibaba.com
The return value from the call to cht_wc_leds_find_freq() is int.
However, the return value is being assigned to an unsigned
int variable 'ctrl', so making it an int.
Eliminate the following warning:
drivers/leds/leds-cht-wcove.c:236 cht_wc_leds_set_effect() warn: unsigned 'ctrl' is never less than zero.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5341
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230531020238.102684-1-yang.lee@linux.alibaba.com
The introduction of high resolution PWM support changed the order of the
operations in the calculation of min and max period. The result in both
divisions is in most cases a truncation to 0, which limits the period to
the range of [0, 0].
Both numerators (and denominators) are within 64 bits, so the whole
expression can be put directly into the div64_u64, instead of doing it
partially.
Fixes: b00d2ed376 ("leds: rgb: leds-qcom-lpg: Add support for high resolution PWM")
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Lee Jones <lee@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20230515162604.649203-1-quic_bjorande@quicinc.com
Signed-off-by: Johan Hovold <johan@kernel.org>
This commit adds support for AWINIC AW20036/AW20054/AW20072 LED driver.
This driver supports following AW200XX features:
- Individual 64-level DIM currents
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230519130403.212479-3-mmkurbanov@sberdevices.ru
Signed-off-by: Lee Jones <lee@kernel.org>
Expose netdev trigger modes to make them accessible by LED driver that
will support netdev trigger for hw control.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On netdev trigger activation, hw control may be already active by
default. If this is the case and a device is actually provided by
hw_control_get_device(), init the already active mode and set the
bool to hw_control bool to true to reflect the already set mode in the
trigger_data.
Co-developed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev which the LED should blink for is configurable in
/sys/class/led/foo/device_name. Ensure when offloading that the
configured netdev is the same as the netdev the LED is associated
with. If it is not, only perform software blinking.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for LED hw control for the netdev trigger.
The trigger on calling set_baseline_state to configure a new mode, will
do various check to verify if hw control can be used for the requested
mode in can_hw_control() function.
It will first check if the LED driver supports hw control for the netdev
trigger, then will use hw_control_is_supported() and finally will call
hw_control_set() to apply the requested mode.
To use such mode, interval MUST be set to the default value and net_dev
MUST be set. If one of these 2 value are not valid, hw control will
never be used and normal software fallback is used.
The default interval value is moved to a define to make sure they are
always synced.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reject interval store with hw_control enabled. It's are currently not
supported and MUST be set to the default value with hw control enabled.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic check for hw control support. Check if the required API are
defined and check if the defined trigger supported in hw control for the
LED driver match netdev.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function to check if the requested mode can use hw control in
preparation for hw control support. Currently everything is handled in
software so can_hw_control will always return false.
Add knob with the new value hw_control in trigger_data struct to
set hw control possible. Useful for future implementation to implement
in set_baseline_state() the required function to set the requested mode
using LEDs hw control ops and in other function to reject set if hw
control is currently active.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code into a helper, ready for it to be called at
other times. No intended behaviour change.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each gpio-leds DT node DT subnode can have a pinctrl property assigned
to it, parse the DT subnode pinctrl properties and configure each pin
accordingly.
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230523183151.5460-1-marex@denx.de
Signed-off-by: Lee Jones <lee@kernel.org>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20230522105049.1467313-18-schnelle@linux.ibm.com
Signed-off-by: Lee Jones <lee@kernel.org>
The call netdev_{put, hold} of dev_{put, hold} will check NULL,
so there is no need to check before using dev_{put, hold},
remove it to silence the warnings:
./drivers/leds/trigger/ledtrig-netdev.c:291:3-10: WARNING: NULL check before dev_{put, hold} functions is not needed.
./drivers/leds/trigger/ledtrig-netdev.c:401:2-9: WARNING: NULL check before dev_{put, hold} functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=4929
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230511070820.52731-1-yang.lee@linux.alibaba.com
Signed-off-by: Lee Jones <lee@kernel.org>
Not all triggers use LED_INIT_DEFAULT_TRIGGER, which means that it
will not get cleared when the default trigger is a trigger which
does not use it such as "default-on".
If the default trigger then later gets replaced by a trigger which
does check LED_INIT_DEFAULT_TRIGGER, such as "timer" then that trigger
will behave as if it is the default trigger which it should not do.
To fix this clear the LED_INIT_DEFAULT_TRIGGER flag when clearing
the current trigger, so that it will not be set for any subsequently
set (non default) triggers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Link: https://lore.kernel.org/r/20230510162234.291439-5-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
led_trigger_blink() calls led_blink_set() from a RCU read-side critical
section so led_blink_set() must not sleep. Note sleeping was not allowed
before the switch to RCU either because a spinlock was held before.
led_blink_set() does not sleep when sw-blinking is used, but
many LED controller drivers with hw blink support have a blink_set
function which may sleep, leading to an oops like this one:
[ 832.605062] ------------[ cut here ]------------
[ 832.605085] Voluntary context switch within RCU read-side critical section!
[ 832.605119] WARNING: CPU: 2 PID: 370 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch+0x4ee/0x690
<snip>
[ 832.606453] Call Trace:
[ 832.606466] <TASK>
[ 832.606487] __schedule+0x9f/0x1480
[ 832.606527] schedule+0x5d/0xe0
[ 832.606549] schedule_timeout+0x79/0x140
[ 832.606572] ? __pfx_process_timeout+0x10/0x10
[ 832.606599] wait_for_completion_timeout+0x6f/0x140
[ 832.606627] i2c_dw_xfer+0x101/0x460
[ 832.606659] ? psi_group_change+0x168/0x400
[ 832.606680] __i2c_transfer+0x172/0x6d0
[ 832.606709] i2c_smbus_xfer_emulated+0x27d/0x9c0
[ 832.606732] ? __schedule+0x430/0x1480
[ 832.606753] ? preempt_count_add+0x6a/0xa0
[ 832.606778] ? get_nohz_timer_target+0x18/0x190
[ 832.606796] ? lock_timer_base+0x61/0x80
[ 832.606817] ? preempt_count_add+0x6a/0xa0
[ 832.606842] __i2c_smbus_xfer+0xa2/0x3f0
[ 832.606862] i2c_smbus_xfer+0x66/0xf0
[ 832.606882] i2c_smbus_read_byte_data+0x41/0x70
[ 832.606901] ? _raw_spin_unlock_irqrestore+0x23/0x40
[ 832.606922] ? __pm_runtime_suspend+0x46/0xc0
[ 832.606946] cht_wc_byte_reg_read+0x2e/0x60
[ 832.606972] _regmap_read+0x5c/0x120
[ 832.606997] _regmap_update_bits+0x96/0xc0
[ 832.607023] regmap_update_bits_base+0x5b/0x90
[ 832.607053] cht_wc_leds_brightness_get+0x412/0x910 [leds_cht_wcove]
[ 832.607094] led_blink_setup+0x28/0x100
[ 832.607119] led_trigger_blink+0x40/0x70
[ 832.607145] power_supply_update_leds+0x1b7/0x1c0
[ 832.607174] power_supply_changed_work+0x67/0xe0
[ 832.607198] process_one_work+0x1c8/0x3c0
[ 832.607222] worker_thread+0x4d/0x380
[ 832.607243] ? __pfx_worker_thread+0x10/0x10
[ 832.607258] kthread+0xe9/0x110
[ 832.607279] ? __pfx_kthread+0x10/0x10
[ 832.607300] ret_from_fork+0x2c/0x50
[ 832.607337] </TASK>
[ 832.607344] ---[ end trace 0000000000000000 ]---
Add a new led_blink_set_nosleep() function which defers the actual
led_blink_set() call to a workqueue when necessary to fix this.
This also fixes an existing race where a pending led_set_brightness() has
been deferred to set_brightness_work and might then race with a later
led_cdev->blink_set() call. Note this race is only an issue with triggers
mixing led_trigger_event() and led_trigger_blink() calls, sysfs API
calls and led_trigger_blink_oneshot() are not affected.
Note rather then adding a separate blink_set_blocking callback this uses
the presence of the already existing brightness_set_blocking callback to
detect if the blinking call should be deferred to set_brightness_work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Link: https://lore.kernel.org/r/20230510162234.291439-4-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
When a trigger wants to switch from blinking to LED on it needs to call:
led_set_brightness(LED_OFF);
led_set_brightness(LED_FULL);
To first call disables blinking and the second then turns the LED on
(the power-supply charging-blink-full-solid triggers do this).
These calls happen immediately after each other, so it is possible
that set_brightness_delayed() from the first call has not run yet
when the led_set_brightness(LED_FULL) call finishes.
If this race hits then this is causing problems for both
sw- and hw-blinking:
For sw-blinking set_brightness_delayed() clears delayed_set_value
when LED_BLINK_DISABLE is set causing the led_set_brightness(LED_FULL)
call effects to get lost when hitting the race, resulting in the LED
turning off instead of on.
For hw-blinking if the race hits delayed_set_value has been
set to LED_FULL by the time set_brightness_delayed() runs.
So led_cdev->brightness_set_blocking() is never called with
LED_OFF as argument and the hw-blinking is never disabled leaving
the LED blinking instead of on.
Fix both issues by adding LED_SET_BRIGHTNESS and LED_SET_BRIGHTNESS_OFF
work_flags making this 2 separate actions to be run by
set_brightness_delayed().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Link: https://lore.kernel.org/r/20230510162234.291439-3-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
led_blink_set[_oneshot]()'s delay_on and delay_off function parameters
are pass by reference, so that hw-blink implementations can report
back the actual achieved delays when the values have been rounded
to something the hw supports.
This is really only interesting for the sysfs API / the timer trigger.
Other triggers don't really care about this and none of the callers of
led_trigger_blink[_oneshot]() do anything with the returned delay values.
Change the led_trigger_blink[_oneshot]() delay parameters to pass-by-value,
there are 2 reasons for this:
1. led_cdev->blink_set() may sleep, while led_trigger_blink() may not.
So on hw where led_cdev->blink_set() sleeps the call needs to be deferred
to a workqueue, in which case the actual achieved delays are unknown
(this is a preparation patch for the deferring).
2. Since the callers don't care about the actual achieved delays, allowing
callers to directly pass a value leads to simpler code for most callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517180559.166329-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
Currently, LEDS_LM3697 and LEDS_LM36274 depend on LEDS_TI_LMU_COMMON,
which contains the common code to support TI LMU devices. This means
the user is asked about the common code first, followed by the
individual drivers, if their dependencies are met.
Simplify this, and reduce the number of questions by making
LEDS_TI_LMU_COMMON invisible, and letting it be selected when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/91f6efaa48c36320e58b6a312025ae9b39ee206b.1683644796.git.geert+renesas@glider.be
Signed-off-by: Lee Jones <lee@kernel.org>
The Qualcomm PMI8998 PMIC requires the LED to be disabled when configuring
the brightness. Always disable the LED when setting the brightness and
re-enable it afterwards.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Link: https://lore.kernel.org/r/20230507172941.364852-3-me@dylanvanassche.be
Signed-off-by: Lee Jones <lee@kernel.org>
Add subtype for the Qualcomm PMI8998 PMIC to support it besides the
PM8150 PMIC which has the same registers. Adjust the driver to recognize
both PMIC subtypes as a 3 channel LED driver.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Link: https://lore.kernel.org/r/20230507172941.364852-2-me@dylanvanassche.be
Signed-off-by: Lee Jones <lee@kernel.org>
The desired default behavior of LED1 / the charge LED is breathing
while charging and on/solid when full. Since triggers cannot select
breathing, blink_set() gets called when charging. Use breathing
when the default "charging-blink-full-solid" trigger is used to
achieve the desired default behavior.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-6-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
The hw-blinking of the LED controller in the Whiskey Cove PMIC can also
be used for a hw-breathing effect.
As discussed during review of v2 of the submission of the new
leds-cht-wcove driver, the LED subsystem already supports breathing mode
on several other LED controllers using the hw_pattern interface.
Implement a pattern_set callback to implement breathing mode modelled
after the breathing mode supported by the SC27xx breathing light and
Crane EL15203000 LED drivers. The Whiskey Cove PMIC's breathing mode
is closer to the EL15203000 one then to the SC27xx one since it does
not support staying high / low for a specific time, it only supports
rise and fall times.
As such the supported hw_pattern and the documentation for this is almost
a 1:1 copy of the pattern/docs for the EL15203000 breathing mode.
Suggested-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Link: https://lore.kernel.org/all/6beed61c-1fc6-6525-e873-a8978f5fbffb@gmail.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-4-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
When LED1 is showing the tablet is charging and then the device gets
suspended followed by unplugging the charger, then it will incorrectly
still show it is charging.
To avoid this turn both LEDs off on suspend, just like the PMIC always
turns them off when the tablet is powered off (even if the tablet is
charging). If hw-control is supported for LED1, then restore the
initial hw-control settings to let the hw control LED1 while suspended.
To restore the state the LEDs had before suspending, save it before
turning the LEDs off and restore it on resume.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-3-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for LEDs connected to the Intel Cherry Trail Whiskey Cove
PMIC. Charger and general-purpose LEDs are supported. Hardware blinking
is implemented, breathing is not.
This driver was tested with Lenovo Yoga Book notebook.
Changes by Hans de Goede (in response to review of v2):
- Since the PMIC is connected to the battery any changes we make to
the LED settings are permanent, even surviving reboot / poweroff.
Save LED1 register settings on probe() and if auto-/hw-control was
enabled on probe() restore the settings on remove() and shutdown().
- Delay switching LED1 to software control mode to first brightness write.
- Use dynamically allocated drvdata instead of a global drvdata variable.
- Ensure the LED is on when activating blinking.
- Fix CHT_WC_LED_EFF_BREATHING val ((3 << 1) rather then BIT(3)).
Link: https://lore.kernel.org/r/20190212205901.13037-2-jekhor@gmail.com
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
The PMI632 PMIC contains 5 PWM channels, 3 of which can be used for
LEDs.
For the LED pattern it doesn't have LUT like other PMICs but uses SDAM
instead. This is not currently implemented in the driver but since LPG
works fine without it, add support for the PMIC now.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v2-4-98bafa909c36@z3ntu.xyz
The LP55xx range of devices have an internal charge pump which
can (automatically) increase the output voltage towards the
LED's, boosting the output voltage to 4.5V.
Implement this option from the devicetree. When the setting
is not present it will operate in automatic mode as before.
Tested on LP55231. Datasheet analysis shows that LP5521, LP5523
and LP8501 are identical in topology and are modified in the
same way.
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230421075305.37597-3-maarten.zanders@mind.be
Some LEDs may require to sleep while doing some operation like setting
brightness and other cleanup.
For this reason, using a spinlock will cause a sleep under spinlock
warning.
It should be safe to convert this to a sleepable lock since:
- sysfs read/write can sleep
- netdev_trig_work is a work queue and can sleep
- netdev _trig_notify can sleep
The spinlock was used when brightness didn't support sleeping, but this
changed and now it supported with brightness_set_blocking().
Convert to mutex lock to permit sleeping using brightness_set_blocking().
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-6-ansuelsmth@gmail.com
Convert link tx and rx device attr to a common macro to reduce common
code and in preparation for additional attr.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-5-ansuelsmth@gmail.com
Rename NETDEV trigger enum modes to a more symbolic name and add a
namespace to them.
Also add __TRIGGER_NETDEV_MAX to identify the max modes of the netdev
trigger.
This is a cleanup to drop the define and no behaviour change are
intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-4-ansuelsmth@gmail.com
Putting NETDEV_LED_MODE_LINKUP in the same list of the netdev trigger
modes is wrong as it's used to set the link state of the device and not
to set a blink mode as it's done by NETDEV_LED_LINK, NETDEV_LED_TX and
NETDEV_LED_RX. It's also wrong to put this state in the same bitmap of the
netdev trigger mode and should be external to it.
Drop NETDEV_LED_MODE_LINKUP from mode list and convert to a simple bool
that will be true or false based on the carrier link. No functional
change intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-3-ansuelsmth@gmail.com
Dev can be renamed also while up for supported device. We currently
wrongly clear the NETDEV_LED_MODE_LINKUP flag on NETDEV_CHANGENAME
event.
Fix this by rechecking if the carrier is ok on NETDEV_CHANGENAME and
correctly set the NETDEV_LED_MODE_LINKUP bit.
Fixes: 5f820ed523 ("leds: trigger: netdev: fix handling on interface rename")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-2-ansuelsmth@gmail.com
- Add support for MediaTek MT6370 LED Indicator
- Add support for MediaTek MT6370 Flashlight
- Add support for QCOM PMIC Flash
- Add support for Rohm BD2606MVV Charge Pump LED
- New Device Support
- Add support for PMK8550 PWM to QCOM LPG
- New Functionality
- Add support for high resolution PWM to QCOM LPG
- Fix-ups
- Kconfig 'depends' and 'select' dependency changes
- Remove unused / irrelevant includes
- Remove unnecessary checks (already performed further into the call stack)
- Trivial: Fix commentary, simplify error messages
- Rid 'defined but not used' warnings
- Provide documentation
- Explicitly provide include files
- Bug Fixes
- Mark GPIO LED as BROKEN
- Fix Kconfig entries
- Fix various Smatch staticify reports
- Fix error handling (or a lack there of)
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAmRRONwACgkQUa+KL4f8
d2Er8w/+Iu6LK+NvxSvELKzyuUw8gsJxCmAYSTFc2ywjFKPJK91giAXYBhvFFhlv
mduJkO+Mbz3yFdXTmG3OjTs/K9J/XIjOl0mB4FTWLsthyytJwUbZIdr9La60/LF/
0ExWCI3lRPEFLC1kbODmgpDrBmlegqH5vzvGStmy3r4HbDvBVXl1No5ArWYXMof1
e4W7p0tCQNOKaSDLpbQNcFzZ5682h/CY/+R6UQzTiI+6/3g+3IqHa4qqtcXGI0Tk
7UtPuGd5f7Gm+1iQO+gxXAlOPictOI5SfHIVWJqtfAEY4RetBulyxkOaG+dw/LN3
pp77yF6b4DU7P89jb/cKL1lD5y3SCYJpNwZrkkytGDqeS4C2J218RTPGzvrJLAtj
tNa65SC7fM6Qh/Mv8b5A7wMrysAF2JAusP8UEBamVNlyt2jTY/MwO3EgTNVFuNGo
um88Cia1BIQMSej0GpRFbOqflbrGEVqJjh/ag7ftGp9jnO4gmCSB5LuNN6QGhtQ8
0T2agMZ9udd2nNKlgbfxvAM+rqGq0/KSgX6nt7XRDDfw5rOI5YZORUFNmo4IKVyx
bfzPW8QOpL6fbtfbFktJDgndV4bKJ1zRLUgk9PhfL23tiSo3HuC+0NdFqG0UCaEy
RnNm8k4Q5SD+OfnzstMF9Zq0cXWCjFm7QVVElRBSFs/fzP5iHfE=
=aJQw
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for MediaTek MT6370 LED Indicator
- Add support for MediaTek MT6370 Flashlight
- Add support for QCOM PMIC Flash
- Add support for Rohm BD2606MVV Charge Pump LED
New Device Support:
- Add support for PMK8550 PWM to QCOM LPG
New Functionality:
- Add support for high resolution PWM to QCOM LPG
Fix-ups:
- Kconfig 'depends' and 'select' dependency changes
- Remove unused / irrelevant includes
- Remove unnecessary checks (already performed further into the call stack)
- Trivial: Fix commentary, simplify error messages
- Rid 'defined but not used' warnings
- Provide documentation
- Explicitly provide include files
Bug Fixes:
- Mark GPIO LED as BROKEN
- Fix Kconfig entries
- Fix various Smatch staticify reports
- Fix error handling (or a lack there of)"
* tag 'leds-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (30 commits)
leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver
dt-bindings: leds: Add ROHM BD2606MVV LED
docs: leds: ledtrig-oneshot: Fix spelling mistake
leds: pwm-multicolor: Simplify an error message
dt-bindings: leds: Convert PCA9532 to dtschema
leds: rgb: leds-qcom-lpg: Add support for PMK8550 PWM
leds: rgb: leds-qcom-lpg: Add support for high resolution PWM
dt-bindings: leds-qcom-lpg: Add qcom,pmk8550-pwm compatible string
leds: tca6507: Fix error handling of using fwnode_property_read_string
leds: flash: Set variables mvflash_{3,4}ch_regs storage-class-specifier to static
leds: rgb: mt6370: Correct config name to select in LEDS_MT6370_RGB
MAINTAINERS: Add entry for LED devices documentation
Documentation: leds: MT6370: Use bullet lists for timing variables
Documentation: leds: mt6370: Properly wrap hw_pattern chart
Documentation: leds: Add MT6370 doc to the toctree
leds: rgb: mt6370: Fix implicit declaration for FIELD_GET
docs: leds: Add MT6370 RGB LED pattern document
leds: flash: mt6370: Add MediaTek MT6370 flashlight support
leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support
dt-bindings: leds: spmi-flash-led: Add pm6150l compatible
...
The device provides 6 channels which can be individually
turned off and on but groups of two channels share a common brightness
register.
Limitation: The GPIO to enable the device is not used yet.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419111806.1100437-3-andreas@kemnade.info
Certain PMICs like PMK8550 have a high resolution PWM module which can
support from 8-bit to 15-bit PWM. Add support for it.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230407223849.17623-3-quic_amelende@quicinc.com
Commit 96f524105b ("leds: tca6507: use fwnode API instead of OF")
changed to fwnode API but did not take into account that a missing property
"linux,default-trigger" now seems to return an error and as a side effect
sets value to -1. This seems to be different from of_get_property() which
always returned NULL in any case of error.
Neglecting this side-effect leads to
[ 11.201965] Unable to handle kernel paging request at virtual address ffffffff when read
in the strcmp() of led_trigger_set_default() if there is no led-trigger
defined in the DTS.
I don't know if this was recently introduced somewhere in the fwnode lib
or if the effect was missed in initial testing. Anyways it seems to be a
bug to ignore the error return value of an optional value here in the
driver.
Fixes: 96f524105b ("leds: tca6507: use fwnode API instead of OF")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/cbae7617db83113de726fcc423a805ebaa1bfca6.1680433978.git.hns@goldelico.com
Smatch reports:
drivers/leds/flash/leds-qcom-flash.c:103:18: warning:
symbol 'mvflash_3ch_regs' was not declared. Should it be static?
drivers/leds/flash/leds-qcom-flash.c:115:18: warning:
symbol 'mvflash_4ch_regs' was not declared. Should it be static?
These variables are only used locally, so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230317191341.1670660-1-trix@redhat.com
Commit 55a8a5c16eb3 ("leds: rgb: mt6370: Add MediaTek MT6370 current sink
type LED Indicator support") introduces the config LEDS_MT6370_RGB, which
selects the non-existing config LINEAR_RANGE. As the driver includes
linux/linear_range.h, it is a safe guess that the config actually intends
to select LINEAR_RANGES, which provides the library implementation for the
function prototypes defined in the linear_range header file.
Correct this naming confusion in the LEDS_MT6370_RGB config definition.
Fixes: 55a8a5c16eb3 ("leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230323105410.10396-1-lukas.bulwahn@gmail.com
0-DAY CI Kernel Test Service reported the implicit declaration error below:
drivers/leds/rgb/leds-mt6370-rgb.c: In function'mt6370_check_vendor_info':
>> drivers/leds/rgb/leds-mt6370-rgb.c:889:15: error: implicit declaration
of function 'FIELD_GET' [-Werror=implicit-function-declaration]
889 | vid = FIELD_GET(MT6370_VENDOR_ID_MASK, devinfo);
|
Add the missing header 'bitfield.h' to fix it.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202303171729.CcgyFx17-lkp@intel.com/
Fixes: 55a8a5c16eb3 ("leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/1679067760-19098-1-git-send-email-cy_huang@richtek.com
The MediaTek MT6370 is a highly-integrated smart power management IC,
which includes a single cell Li-Ion/Li-Polymer switching battery
charger, a USB Type-C & Power Delivery (PD) controller, dual Flash
LED current sources, a RGB LED driver, a backlight WLED driver,
a display bias driver and a general LDO for portable devices.
Add support for the MT6370 Flash LED driver. Flash LED in MT6370
has 2 channels and support torch/strobe mode.
Co-developed-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/52480420a160e5a4c71715fbbf105e684a16e7c2.1678430444.git.chiaen_wu@richtek.com
The MediaTek MT6370 is a highly-integrated smart power management IC,
which includes a single cell Li-Ion/Li-Polymer switching battery
charger, a USB Type-C & Power Delivery (PD) controller, dual
Flash LED current sources, a RGB LED driver, a backlight WLED driver,
a display bias driver and a general LDO for portable devices.
Add support for the MediaTek MT6370 Current Sink Type LED Indicator
driver. It can control four channels current-sink RGB LEDs with 3 modes:
constant current, PWM, and breath mode.
Co-developed-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/1df93a583c3f508a7158b83b95857e9bce235e1b.1678430444.git.chiaen_wu@richtek.com
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add initial driver to support flash LED module found in Qualcomm
Technologies, Inc. PMICs. The flash module can have 3 or 4 channels
and each channel can be controlled indepedently and support full scale
current up to 1.5 A. It also supports connecting two channels together
to supply one LED component with full scale current up to 2 A. In that
case, the current will be split on each channel symmetrically and the
channels will be enabled and disabled at the same time.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sm7225-fairphone-fp4 + pm6150l
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230303095023.538917-2-quic_fenglinw@quicinc.com
The GPIO LED trigger exposes a userspace ABI where a user
can echo a GPIO number from the global GPIO numberspace into
a file that will trigger a certain LED when active.
This is problematic because the global GPIO numberspace is
inherently instable. The trigger came about at a time when
systems had one GPIO controller that defined hard-wired
GPIOs numbered 0..N and this number space was stable.
We have since moved to dynamic allocation of GPIO numbers
and there is no real guarantee that a GPIO number will stay
consistent even across a reboot: consider a USB attached
GPIO controller for example. Or two. Or the effect of
probe order after adding -EPROBE_DEFER to the kernel.
The trigger was added to support keypad LEDs on the Nokia
n810 from the GPIO event when a user slides up/down the
keypad. This is arch/arm/boot/dts/omap2420-n810.dts.
A userspace script is needed to activate the trigger.
This will be broken unless the script was updated recently
since the OMAP GPIO controller now uses dynamic GPIO
number allocations.
I want to know that this trigger has active users that
cannot live without it if we are to continue to support it.
Option if this is really needed: I can develop a new trigger
that can associate GPIOs with LEDs as triggers using device
tree, which should also remove the use of userspace custom
scripts to achieve this and be much more trustworthy, if
someone with the Nokia n810 or a device with a similar need
is willing to test it.
Suggested-by Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230314210059.419159-1-linus.walleij@linaro.org
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/leds/leds-tlc591xx.c:138:34: error: ‘of_tlc591xx_leds_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230311111717.252019-1-krzysztof.kozlowski@linaro.org
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 3fce8e1eb9 ("leds: TI LMU: Add common code for TI LMU devices")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230226053953.4681-5-rdunlap@infradead.org
- HTC ASIC3 LED
- New Functionality
- Provide generic led_get() which can be used by both DT and !DT platforms
- Fix-ups
- Convert a bunch of I2C subsystem users to the new probing API
- Explicitly provide missing include files
- Make use of led_init_default_state_get() and rid the custom variants
- Use simplified fwnode_device_is_compatible() API
- Provide some Device Tree additions / adaptions
- Fix some trivial spelling issues
- Bug Fixes
- Prevent device refcount leak during led_put() and of_led_get()
- Clear previous data from temporary led_pwm structure before processing next child
- Fix Clang's warning about incompatible function types when using devm_add_action*()
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAmP3Kb4ACgkQUa+KL4f8
d2HUfA//W+DfluN4PzYbcF/dSItfZDIOjKTUOP5ufb6t/jQMvCzXUMbcnELWTVOi
PZuXW8sFC81EFq7+gglGCZPRBMN+fthlgKHRdbs+rYCntpD7OnMv4GC3OHncTw22
HXr0R3K/W5/197P89ZhX/I0B60aT+XZhbcIh55std8fSjXXhzb2211sRzg4xemzF
eUVGygZ8qi7bGQQ9f3VlouSm8V3WJqK0JpyMDpQG6SuwAU8VkXFNexzBnbp2jmDj
IHlltppS5izNiv2tFy4NCwRMdR33pjreVfYqaT+YlRSeB8SWIvVb5FeGr6NUxi/U
aerjmjkRKtX3m+YL3+wrEVavO8bl+oXFvefuiCmTCMji8aD/D1d/6Sp7DW0ktV3f
VTToB+C/Jwj9rKsuL3ImR7vYM3E2wysU5/NfGgIEoUJBkokrTxOsFlg1qBrEKInp
RAR808jsOxlJeuDLAuj2Z3P2z4REgMhyUUOhvWF2sxNW6oRrwO+vApjjJAcTp/pu
wbfAdSVoDX1T8Ij3OJVDrct2YYPAg9rwCJ1lYX7WD2ajnOfQMaQ5wDNYwefyW3u6
Em3qDnDXwv4WTbeijR+wr/6KEKV70xHd59VJbO1z9yPrR2dQZZlMQ3VPY79Wi4LR
04AMdzNxlOkWDTn9o9ybDGT1X6K0saja5qCUvymhuSRHZqzVvBM=
=bbUo
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Removed Drivers:
- HTC ASIC3 LED
New Functionality:
- Provide generic led_get() which can be used by both DT and !DT
platforms
Fix-ups:
- Convert a bunch of I2C subsystem users to the new probing API
- Explicitly provide missing include files
- Make use of led_init_default_state_get() and rid the custom
variants
- Use simplified fwnode_device_is_compatible() API
- Provide some Device Tree additions / adaptions
- Fix some trivial spelling issues
Bug Fixes:
- Prevent device refcount leak during led_put() and of_led_get()
- Clear previous data from temporary led_pwm structure before
processing next child
- Fix Clang's warning about incompatible function types when using
devm_add_action*()"
* tag 'leds-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (41 commits)
leds: Remove ide-disk trigger
dt-bindings: leds: Add disk write/read and usb-host/usb-gadget
Documentation: leds: Correct spelling
dt-bindings: leds: Document Bluetooth and WLAN triggers
leds: Remove asic3 driver
leds: simatic-ipc-leds-gpio: Make sure we have the GPIO providing driver
leds: tca6507: Convert to use fwnode_device_is_compatible()
leds: syscon: Get rid of custom led_init_default_state_get()
leds: pm8058: Get rid of custom led_init_default_state_get()
leds: pca955x: Get rid of custom led_init_default_state_get()
leds: mt6360: Get rid of custom led_init_default_state_get()
leds: mt6323: Get rid of custom led_init_default_state_get()
leds: bcm6358: Get rid of custom led_init_default_state_get()
leds: bcm6328: Get rid of custom led_init_default_state_get()
leds: an30259a: Get rid of custom led_init_default_state_get()
leds: Move led_init_default_state_get() to the global header
leds: Add missing includes and forward declarations in leds.h
leds: is31fl319x: Wrap mutex_destroy() for devm_add_action_or_rest()
leds: turris-omnia: Convert to i2c's .probe_new()
leds: tlc591xx: Convert to i2c's .probe_new()
...
Highlights:
- AMD PMC: Improvements to aid s2idle debugging
- Dell WMI-DDV: hwmon support
- INT3472 camera sensor power-management: Improve privacy LED support
- Intel VSEC: Base TPMI (Topology Aware Register and PM Capsule Interface) support
- Mellanox: SN5600 and Nvidia L1 switch support
- Microsoft Surface Support: Various cleanups + code improvements
- tools/intel-speed-select: Various improvements
- Miscellaneous other cleanups / fixes
The following is an automated git shortlog grouped by driver:
Add include/linux/platform_data/x86 to MAINTAINERS:
- Add include/linux/platform_data/x86 to MAINTAINERS
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
Fix header inclusion in linux/platform_data/x86/soc.h:
- Fix header inclusion in linux/platform_data/x86/soc.h
HID:
- surface-hid: Use target-ID enum instead of hard-coding values
MAINTAINERS:
- dell-wmi-sysman: drop Divya Bharathi
- Add entry for TPMI driver
Merge tag 'ib-leds-led_get-v6.3' into HEAD:
- Merge tag 'ib-leds-led_get-v6.3' into HEAD
acerhdf:
- Drop empty platform remove function
apple_gmux:
- Drop no longer used ACPI_VIDEO Kconfig dependency
dell-ddv:
- Prefer asynchronous probing
- Add hwmon support
- Add "force" module param
- Replace EIO with ENOMSG
- Return error if buffer is empty
- Add support for interface version 3
dell-smo8800:
- Use min_t() for comparison and assignment
dell-wmi-sysman:
- Make kobj_type structure constant
hp-wmi:
- Ignore Win-Lock key events
int1092:
- Switch to use acpi_evaluate_dsm_typed()
int3472/discrete:
- add LEDS_CLASS dependency
- Drop unnecessary obj->type == string check
- Get the polarity from the _DSM entry
- Move GPIO request to skl_int3472_register_clock()
- Create a LED class device for the privacy LED
- Refactor GPIO to sensor mapping
intel:
- punit_ipc: Drop empty platform remove function
- oaktrail: Drop empty platform remove function
intel/pmc:
- Switch to use acpi_evaluate_dsm_typed()
leds:
- led-class: Add generic [devm_]led_get()
- led-class: Add __devm_led_get() helper
- led-class: Add led_module_get() helper
- led-class: Add missing put_device() to led_put()
media:
- v4l2-core: Make the v4l2-core code enable/disable the privacy LED if present
nvidia-wmi-ec-backlight:
- Add force module parameter
platform:
- mellanox: mlx-platform: Move bus shift assignment out of the loop
- mellanox: mlx-platform: Add mux selection register to regmap
- mellanox: Extend all systems with I2C notification callback
- mellanox: Split logic in init and exit flow
- mellanox: Split initialization procedure
- mellanox: Introduce support of new Nvidia L1 switch
- mellanox: Introduce support for next-generation 800GB/s switch
- mellanox: Cosmetic changes - rename to more common name
- mellanox: Change "reset_pwr_converter_fail" attribute
- mellanox: Introduce support for rack manager switch
platform/mellanox:
- mlxreg-hotplug: Allow more flexible hotplug events configuration
platform/surface:
- Switch to use acpi_evaluate_dsm_typed()
- aggregator: Rename top-level request functions to avoid ambiguities
- aggregator_registry: Fix target-ID of base-hub
- aggregator: Enforce use of target-ID enum in device ID macros
- dtx: Use target-ID enum instead of hard-coding values
- aggregator_tabletsw: Use target-ID enum instead of hard-coding values
- aggregator_hub: Use target-ID enum instead of hard-coding values
- aggregator: Add target and source IDs to command trace events
- aggregator: Improve documentation and handling of message target and source IDs
platform/x86/amd:
- pmc: Add line break for readability
- pmc: differentiate STB/SMU messaging prints
- pmc: Write dummy postcode into the STB DRAM
- pmc: Add num_samples message id support to STB
platform/x86/amd/pmf:
- Add depends on CONFIG_POWER_SUPPLY
platform/x86/intel:
- Intel TPMI enumeration driver
platform/x86/intel/tpmi:
- ADD tpmi external interface for tpmi feature drivers
- Process CPU package mapping
platform/x86/intel/vsec:
- Use mutex for ida_alloc() and ida_free()
- Support private data
- Enhance and Export intel_vsec_add_aux()
- Add TPMI ID
platform_data/mlxreg:
- Add field with mapped resource address
think-lmi:
- Make kobj_type structure constant
- Use min_t() for comparison and assignment
tools/power/x86/intel-speed-select:
- v1.14 release
- Adjust uncore max/min frequency
- Add Emerald Rapid quirk
- Fix display of uncore min frequency
- turbo-freq auto mode with SMT off
- cpufreq reads on offline CPUs
- Use null-terminated string
- Remove duplicate dup()
- Handle open() failure case
- Remove unused non_block flag
- Remove wrong check in set_isst_id()
x86/platform/uv:
- Make kobj_type structure constant
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmPzRpgUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9wYPwf+I6PP0XBg8MrivLc2DHklVojUU0aX
/M0LbCP8gxCDdyisV8swC3e848riaTchYlUGASPZu0ieas1U7KsDvghkiittNvlI
U+0h7TbkOQNymM8oE0oauflH4W5KwCXGrLsJWVkGk0lhJd6WmjXkjWLkruaXazLd
kc5fq0QyzRVzhhCtocQ7qhIgXSZyKYx433VqbDR7/SUi5F2wkC9JbGY02maKWaK3
4lQaoyMKLjGlDr9YVv+UHTwLoXwP0mW/fjlsZ3Xz5lz6WfihQzPuOrl/10mRj0Ez
eP9dlF1Dipee4BYS2FM5dtk5xPpqdVqRlQUX2qKzyDNTSx5wdtJnv8j/cg==
=VoXq
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- AMD PMC: Improvements to aid s2idle debugging
- Dell WMI-DDV: hwmon support
- INT3472 camera sensor power-management: Improve privacy LED support
- Intel VSEC: Base TPMI (Topology Aware Register and PM Capsule
Interface) support
- Mellanox: SN5600 and Nvidia L1 switch support
- Microsoft Surface Support: Various cleanups + code improvements
- tools/intel-speed-select: Various improvements
- Miscellaneous other cleanups / fixes
* tag 'platform-drivers-x86-v6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (80 commits)
platform/x86: nvidia-wmi-ec-backlight: Add force module parameter
platform/x86/amd/pmf: Add depends on CONFIG_POWER_SUPPLY
platform/x86: dell-ddv: Prefer asynchronous probing
platform/x86: dell-ddv: Add hwmon support
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform: mellanox: mlx-platform: Move bus shift assignment out of the loop
platform: mellanox: mlx-platform: Add mux selection register to regmap
platform_data/mlxreg: Add field with mapped resource address
platform/mellanox: mlxreg-hotplug: Allow more flexible hotplug events configuration
platform: mellanox: Extend all systems with I2C notification callback
platform: mellanox: Split logic in init and exit flow
platform: mellanox: Split initialization procedure
platform: mellanox: Introduce support of new Nvidia L1 switch
platform: mellanox: Introduce support for next-generation 800GB/s switch
platform: mellanox: Cosmetic changes - rename to more common name
platform: mellanox: Change "reset_pwr_converter_fail" attribute
platform: mellanox: Introduce support for rack manager switch
MAINTAINERS: dell-wmi-sysman: drop Divya Bharathi
x86/platform/uv: Make kobj_type structure constant
platform/x86: think-lmi: Make kobj_type structure constant
...
No user of ide-disk remains, so remove this deprecated trigger.
Only a few platforms used this and were fixed in 2016.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230131140304.626779-2-clabbe@baylibre.com
If we register a "leds-gpio" platform device for GPIO pins that do not
exist we get a -EPROBE_DEFER and the probe will be tried again later.
If there is no driver to provide that pin we will poll forever and also
create a lot of log messages.
So check if that GPIO driver is configured, if so it will come up
eventually. If not, we exit our probe function early and do not even
bother registering the "leds-gpio". This method was chosen over "Kconfig
depends" since this way we can add support for more devices and GPIO
backends more easily without "depends":ing on all GPIO backends.
Fixes: a6c80bec3c ("leds: simatic-ipc-leds-gpio: Add GPIO version of Siemens driver")
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221007153323.1326-1-henning.schild@siemens.com
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-8-andriy.shevchenko@linux.intel.com
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-7-andriy.shevchenko@linux.intel.com
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-6-andriy.shevchenko@linux.intel.com
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-5-andriy.shevchenko@linux.intel.com
There are users inside and outside LED framework that have implemented
a local copy of led_init_default_state_get(). In order to deduplicate
that, as the first step move the declaration from LED header to the
global one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-3-andriy.shevchenko@linux.intel.com
Clang complains that devm_add_action() takes a parameter with a wrong type:
warning: cast from 'void (*)(struct mutex *)' to 'void (*)(void *)' converts to incompatible function type [-Wcast-function-type-strict]
err = devm_add_action(dev, (void (*)(void *))mutex_destroy, &is31->lock);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.
It appears that the commit e1af5c8155 ("leds: is31fl319x: Fix devm vs.
non-devm ordering") missed two things:
- whilst the commit mentions devm_add_action_or_reset() the actual change
utilised devm_add_action() call by mistake
- strictly speaking the parameter is not compatible by type
Fix both issues by switching to devm_add_action_or_reset() and adding a
wrapper for mutex_destroy() call.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e1af5c8155 ("leds: is31fl319x: Fix devm vs. non-devm ordering")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221228093238.82713-1-andriy.shevchenko@linux.intel.com
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-289-uwe@kleine-koenig.org
