On the Allwinner's A31 SoC the reset line connected to the EHCI IP has to
be deasserted for the EHCI block to be usable.
Add support for an optional reset controller that will be deasserted on
power off and asserted on power on.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OHCI controllers used in the Allwinner A31 are asserted in reset using a
global reset controller.
Add optional support for such a controller in the OHCI platform driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dependency on the isp1301 driver is not something that
should be in the main OHCI driver but rather the SoC specific
part of it.
This moves the dependency for LPC32xx into USB_OHCI_HCD_LPC32XX,
and changes the 'select ISP1301_OMAP' to a similar 'depends on'.
Since the same dependency exists for the client driver, do the
same change there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY setup code of the TI DaVinci DA8xx OHCI controller
uses ad-hoc register access using a pointer that is meant to
be used only by the DaVinci platform implementation and that
is intentionally not exported to loadable modules. This results
in a link error on configurations that use a modular OHCI
code on this platform.
While the proper solution for this problem would be to
implement a real PHY driver shared by ohci-da8xx and musb-da8xx,
this patch for now just works around the build error by
only allowing the ohci-da8xx code to be built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we build a kernel with PM_SUSPEND set and no PM_SLEEP,
we get a build warning in the xhci-plat driver about unused
functions.
To fix this, use "#ifdef CONFIG_PM_SLEEP", like we do in most
other drivers nowadays.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Armada 375 and 38x SoCs come with an XHCI controller that requires
some specific initialization related to the MBus windows
configuration. This patch adds the support for this special
configuration as an XHCI quirk executed during probe.
Two new compatible strings are added to identify the Armada 375 and
Armada 38x XHCI controllers, and therefore enable the relevant quirk.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms (such as the Armada 38x ones) can gate the clock of
their USB controller. This patch adds the support for one clock in
xhci-plat, by enabling it during probe and disabling it on remove.
To achieve this, it adds a 'struct clk *' member in xhci_hcd. While
only used for now in xhci-plat, it might be used by other drivers in
the future. Moreover, the xhci_hcd structure already holds other
members such as msix_count and msix_entries, which are MSI-X specific,
and therefore only used by xhci-pci.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sorting the headers in alphabetic order will help to reduce the conflict
when adding new headers later.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit extends the ehci-orion so that it can optionally be passed
a reference to a PHY through the Device Tree. It will be useful for
the Armada 375 SoCs. If no PHY is provided then the behavior of the
driver is unchanged.
[Thomas: use devm_phy_optional_get() so that we handle -EPROBE_DEFER
properly. Also call phy_power_off() when needed, and rename goto
labels.]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to disable the clock in the ->remove() function, a call to
devm_clk_get() is being made, which further increases the reference
count of the clock.
In order to clean this up, a private structure holding a pointer to
the clock is added using the override mechanism provided by the ehci
framework. This makes the driver clock handling much more logical.
The bug was introduced in v3.6, however the ehci framework allowing to
use the override mechanism has only been introduced in v3.8, so this
patch won't apply before it.
[Thomas: reword commit log, fix goto label names.]
Fixes: 8c869edaee ('ARM: Orion: EHCI: Add support for enabling clocks')
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to the introduction of additional initialization steps
in ehci_orion_drv_probe(), we rename the error goto labels from err1,
err2 and err3 names to some more meaningful names.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 77dae54ab3 ('ARM: Kirkwood:
ehci-orion: Add device tree binding') added the Device Tree binding
for the ehci-orion driver. To achieve that with the irq, it used the
irq_of_parse_and_map() function when probed in DT-mode, and
platform_get_irq() when probed in non-DT mode.
This is not necessary: platform_get_irq() works just as fine in
DT-mode, since the conversion from DT information to 'struct resource'
is done by the generic layers of the kernel.
Therefore, this commit switches back to use just platform_get_irq().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the phy provider, supplied by new Exynos-usb2phy using
Generic phy framework.
Keeping the support for older USB phy intact right now, in order
to prevent any functionality break in absence of relevant
device tree side change for ehci-exynos.
Once we move to new phy in the device nodes for ehci, we can
remove the support for older phys.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[gautam.vivek@samsung.com: Addressed review comments from mailing list]
[gautam.vivek@samsung.com: Kept the code for old usb-phy, and just
added support for new exynos5-usb2phy in generic phy framework]
[gautam.vivek@samsung.com: Edited the commit message]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to consume phy provided by Generic phy framework.
Keeping the support for older usb-phy intact right now, in order
to prevent any functionality break in absence of relevant
device tree side change for ohci-exynos.
Once we move to new phy in the device nodes for ohci, we can
remove the support for older phys.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change to use struct device instead of struct platform_device
for some static functions.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change to use struct device instead of struct platform_device
for some static functions.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q1jA
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.16 merge window
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy-mv-u3d-usb.c
Use one timer to control command timeout.
start/kick the timer every time a command is completed and a
new command is waiting, or a new command is added to a empty list.
If the timer runs out, then tag the current command as "aborted", and
start the xhci command abortion process.
Previously each function that submitted a command had its own timer.
If that command timed out, a new command structure for the
command was created and it was put on a cancel_cmd_list list,
then a pci write to abort the command ring was issued.
when the ring was aborted, it checked if the current command
was the one to be canceled, later when the ring was stopped the
driver got ownership of the TRBs in the command ring,
compared then to the TRBs in the cancel_cmd_list,
and turned them into No-ops.
Now, instead, at timeout we tag the status of the command in the
command queue to be aborted, and start the ring abortion.
Ring abortion stops the command ring and gives control of the
commands to us.
All the aborted commands are now turned into No-ops.
If the ring is already stopped when the command times outs its not possible
to start the ring abortion, in this case the command is turnd to No-op
right away.
All these changes allows us to remove the entire cancel_cmd_list code.
The functions waiting for a command to finish no longer have their own timeouts.
They will wait either until the command completes normally,
or until the whole command abortion is done.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the per-device command list and handle_cmd_in_cmd_wait_list()
and use the completion and status variables found in the
command structure in the global command list.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a list to store command structures, add a structure to it every time
a command is submitted, and remove it from the list once we get a
command completion event matching the command.
Callers that wait for completion will free their command structures themselves.
The other command structures are freed in the command completion event handler.
Also add a check that prevents queuing commands if host is dying
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To create a global command queue we require that each command put on the
command ring is submitted with a command structure.
Functions that queue commands and wait for completion need to allocate a command
before submitting it, and free it once completed. The following command queuing
functions need to be modified.
xhci_configure_endpoint()
xhci_address_device()
xhci_queue_slot_control()
xhci_queue_stop_endpoint()
xhci_queue_new_dequeue_state()
xhci_queue_reset_ep()
xhci_configure_endpoint()
xhci_configure_endpoint() could already be called with a command structure,
and only xhci_check_maxpacket and xhci_check_bandwidth did not do so. These
are changed and a command structure is now required. This change also simplifies
the configure endpoint command completion handling and the "goto bandwidth_change"
handling code can be removed.
In some cases the command queuing function is called in interrupt context.
These commands needs to be allocated atomically, and they can't wait for
completion. These commands will in this patch be freed directly after queuing,
but freeing will be moved to the command completion event handler in a later
patch once we get the global command queue up.(Just so that we won't leak
memory in the middle of the patch set)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI host controllers may only support a limited number of device slot
IDs, which is usually far less than the theoretical maximum number of
devices (255) that the USB specifications advertise. This is
frustrating to consumers that expect to be able to plug in a large
number of devices.
Add a print statement when the Enable Slot command fails to show how
many devices the host supports. We can't change hardware manufacturer's
design decisions, but hopefully we can save customers a little bit of
time trying to debug why their host mysteriously fails when too many
devices are plugged in.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Amund Hov <Amund.Hov@silabs.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using the IS_ENABLED() macro can make the code shorter and easier to read.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix wrong port number reported when trying to enable/disable
USB2.0 hardware LPM.
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a273454341 "usb: phy: msm: Use reset framework for LINK
and PHY resets" introduced a mandatory call to reset_control_get
into the msm usb phy driver, which means we have to add a Kconfig
dependency on the API to avoid this build error:
phy/phy-msm-usb.c: In function 'msm_otg_read_dt':
phy/phy-msm-usb.c:1461:2: error: implicit declaration of function 'devm_reset_control_get' [-Werror=implicit-function-declaration]
motg->link_rst = devm_reset_control_get(&pdev->dev, "link");
^
Since the usb-ehci-msm driver currently selects the OTG driver,
we could still get a broken dependency here. To solve that,
this patch also removes the 'select', which turns out to be
unnecessary.
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Per reference manuals of Freescale P1020 and P2020 SoCs, USB controller
present in these SoCs has bit 17 of USBx_CONTROL register marked as
Reserved - there is no PHY_CLK_VALID bit there.
Testing for this bit in ehci_fsl_setup_phy() behaves differently on two
P1020RDB boards available here - on one board test passes and fsl-usb
init succeeds, but on other board test fails, causing fsl-usb init to
fail.
This patch changes ehci_fsl_setup_phy() not to test PHY_CLK_VALID on
controller version 1.6 that (per manual) does not have this bit.
Signed-off-by: Nikita Yushchenko <nyushchenko@dev.rtsoft.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some OHCI controllers from ATI/AMD seem to have difficulty with
"global" USB suspend, that is, suspending an entire USB bus without
setting the suspend feature for each port connected to a device. When
we try to resume the child devices, the controller gives timeout
errors on the unsuspended ports, requiring resets, and can even cause
ohci-hcd to hang; see
http://marc.info/?l=linux-usb&m=139514332820398&w=2
and the following messages.
This patch fixes the problem by adding a new quirk flag to ohci-hcd.
The flag causes the ohci_rh_suspend() routine to suspend each
unsuspended, enabled port before suspending the root hub. This
effectively converts the "global" suspend to an ordinary root-hub
suspend. There is no need to unsuspend these ports when the root hub
is resumed, because the child devices will be resumed anyway in the
course of a normal system resume ("global" suspend is never used for
runtime PM).
This patch should be applied to all stable kernels which include
commit 0aa2832dd0 (USB: use "global suspend" for system sleep on
USB-2 buses) or a backported version thereof.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Peter Münster <pmlists@free.fr>
Tested-by: Peter Münster <pmlists@free.fr>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
warning:
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]
Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.
This warning has been in since 3.2 kernel and was
caused by commit 421aa841a1
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Cc: stable@vger.kernel.org # 3.2
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same issue like with Panther Point chipsets. If the USB ports are
switched to xHCI on shutdown, the xHCI host will send a spurious interrupt,
which will wake the system. Some BIOS have work around for this, but not all.
One example is Compulab's mini-desktop, the Intense-PC2.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.
This patch should be backported to stable kernels as old as 3.12,
that contain the commit 638298dc66
"xhci: Fix spurious wakeups after S5 on Haswell"
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.
The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.
This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.
This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae63674714 "USB: xhci: URB
cancellation support."
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Override the hub control operation to enable and disable external
regulators for the ports vbus power supply in response to clear/set
USB_PORT_FEAT_POWER requests.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers sometimes need to perform specific handling of hub
control requests. Make this possible by exporting the ehci_hub_control()
function which can then be called from a custom hub control handler in
the default case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers sometimes need to perform specific handling of hub
control requests and status data. Make this possible by exporting the
ohci_hub_control() and ohci_hub_status_data() functions which can then
be called from custom hub operations in the default case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch : 14982e3 USB: OHCI: Properly handle ohci-exynos suspend
has already removed 'ohci_hcd' settings from exynos glue layer
as a part of streamlining the ohci controller's suspend.
So we don't need the locks for 'ohci_hcd' anymore.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Power control of hub ports target the CLEAR_FEATURE and SET_FEATURE
requests to ports, not to the hub. Fix the hub control function to
detect the request correctly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ret variable is not initialized in all code paths of the
ohci_jz4740_hub_control function. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid memory fetch underflows with larger USB transfers, Tegra SoCs
need txfill_tuning's txfifothresh register field set to a non-default
value. Add a custom reset override in order to set this up.
These values are recommended practice for all Tegra chips. However,
I've only noticed practical problems when not setting them this way on
systems using Tegra124. Hence, CC: stable only for recent kernels which
actually support Tegra124.
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch 'b8efdaf USB: EHCI: add check for wakeup/suspend race'
adds a check for possible race between suspend and wakeup interrupt,
and thereby it returns -EBUSY as error code if there's a wakeup
interrupt.
So the platform host controller should not proceed further with
its suspend callback, rather should return immediately to avoid
powering down the essential things, like phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch 'b8efdaf USB: EHCI: add check for wakeup/suspend race'
adds a check for possible race between suspend and wakeup interrupt,
and thereby it returns -EBUSY as error code if there's a wakeup
interrupt.
So the platform host controller should not proceed further with
its suspend callback, rather should return immediately to avoid
powering down the essential things, like phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>