sctp_ifwdtsn_skip, sctp_ifwdtsn_hdr and sctp_ifwdtsn_chunk are used to
define and parse I-FWD TSN chunk format, and sctp_make_ifwdtsn is a
function to build the chunk.
The I-FORWARD-TSN Chunk Format is defined in section 2.3.1 of RFC8260.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unordered idata process is more complicated than unordered data:
- It has to add mid into sctp_stream_out to save the next mid value,
which is separated from ordered idata's.
- To support pd for unordered idata, another mid and pd_mode need to
be added to save the message id and pd state in sctp_stream_in.
- To make unordered idata reasm easier, it adds a new event queue
to save frags for idata.
The patch mostly adds the samilar reasm functions for unordered idata
as ordered idata's, and also adjusts some other codes on assign_mid,
abort_pd and ulpevent_data for idata.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
abort_pd is added as a member of sctp_stream_interleave, used to abort
partial delivery for data or idata, called in sctp_cmd_assoc_failed.
Since stream interleave allows to do partial delivery for each stream
at the same time, sctp_intl_abort_pd for idata would be very different
from the old function sctp_ulpq_abort_pd for data.
Note that sctp_ulpevent_make_pdapi will support per stream in this
patch by adding pdapi_stream and pdapi_seq in sctp_pdapi_event, as
described in section 6.1.7 of RFC6458.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
start_pd is added as a member of sctp_stream_interleave, used to
do partial_delivery for data or idata when datalen >= asoc->rwnd
in sctp_eat_data. The codes have been done in last patches, but
they need to be extracted into start_pd, so that it could be used
for SCTP_CMD_PART_DELIVER cmd as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
renege_events is added as a member of sctp_stream_interleave, used to
renege some old data or idata in reasm or lobby queue properly to free
some memory for the new data when there's memory stress.
It defines sctp_renege_events for idata, and leaves sctp_ulpq_renege
as it is for data.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enqueue_event is added as a member of sctp_stream_interleave, used to
enqueue either data, idata or notification events into user socket rx
queue.
It replaces sctp_ulpq_tail_event used in the other places with
enqueue_event.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ulpevent_data is added as a member of sctp_stream_interleave, used to
do the most process in ulpq, including to convert data or idata chunk
to event, reasm them in reasm queue and put them in lobby queue in
right order, and deliver them up to user sk rx queue.
This procedure is described in section 2.2.3 of RFC8260.
It adds most functions for idata here to do the similar process as
the old functions for data. But since the details are very different
between them, the old functions can not be reused for idata.
event->ssn and event->ppid settings are moved to ulpevent_data from
sctp_ulpevent_make_rcvmsg, so that sctp_ulpevent_make_rcvmsg could
work for both data and idata.
Note that mid is added in sctp_ulpevent for idata, __packed has to
be used for defining sctp_ulpevent, or it would exceeds the skb cb
that saves a sctp_ulpevent variable for ulp layer process.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
validate_data is added as a member of sctp_stream_interleave, used
to validate ssn/chunk type for data or mid (message id)/chunk type
for idata, called in sctp_eat_data.
If this check fails, an abort packet will be sent, as said in
section 2.2.3 of RFC8260.
It also adds the process for idata in rx path. As Marcelo pointed
out, there's no need to add event table for idata, but just share
chunk_event_table with data's. It would drop data chunk for idata
and drop idata chunk for data by calling validate_data in
sctp_eat_data.
As last patch did, it also replaces sizeof(struct sctp_data_chunk)
with sctp_datachk_len for rx path.
After this patch, the idata can be accepted and delivered to ulp
layer.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
assign_number is added as a member of sctp_stream_interleave, used
to assign ssn for data or mid (message id) for idata, called in
sctp_packet_append_data. sctp_chunk_assign_ssn is left as it is,
and sctp_chunk_assign_mid is added for sctp_stream_interleave_1.
This procedure is described in section 2.2.2 of RFC8260.
All sizeof(struct sctp_data_chunk) in tx path is replaced with
sctp_datachk_len, to make it right for idata as well. And also
adjust sctp_chunk_is_data for SCTP_CID_I_DATA.
After this patch, idata can be built and sent in tx path.
Note that if sp strm_interleave is set, it has to wait_connect in
sctp_sendmsg, as asoc intl_enable need to be known after 4 shake-
hands, to decide if it should use data or idata later. data and
idata can't be mixed to send in one asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid hundreds of checks for the different process on I-DATA chunk,
struct sctp_stream_interleave is defined as a group of functions used
to replace the codes in some place where it needs to do different job
according to if the asoc intl_enabled is set.
With these ops, it only needs to initialize asoc->stream.si with
sctp_stream_interleave_0 for normal data if asoc intl_enable is 0,
or sctp_stream_interleave_1 for idata if asoc intl_enable is set in
sctp_stream_init.
After that, the members in asoc->stream.si can be used directly in
some special places without checking asoc intl_enable.
make_datafrag is the first member for sctp_stream_interleave, it's
used to make data or idata frags, called in sctp_datamsg_from_user.
The old function sctp_make_datafrag_empty needs to be adjust some
to fit in this ops.
Note that as idata and data chunks have different length, it also
defines data_chunk_len for sctp_stream_interleave to describe the
chunk size.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_idatahdr and sctp_idata_chunk are used to define and parse
I-DATA chunk format, and sctp_make_idata is a function to build
the chunk.
The I-DATA Chunk Format is defined in section 2.1 of RFC8260.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
asoc intl_enable will be set when local sp strm_interleave is set
and there's I-DATA chunk in init and init_ack extensions, as said
in section 2.2.1 of RFC8260.
asoc intl_enable indicates all data will be sent as I-DATA chunks.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds intl_enable in asoc and netns, and strm_interleave in
sctp_sock to indicate if stream interleave is enabled and supported.
netns intl_enable would be set via procfs, but that is not added yet
until all stream interleave codes are completely implemented; asoc
intl_enable will be set when doing 4-shakehands.
sp strm_interleave can be set by sockopt SCTP_INTERLEAVING_SUPPORTED
which is also added in this patch. This socket option is defined in
section 4.3.1 of RFC8260.
Note that strm_interleave can only be set by sockopt when both netns
intl_enable and sp frag_interleave are set.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes calling conventions (and simplifies the hell out
the callers). New rules: once struct socket had been passed
to sock_alloc_file(), it's been consumed either by struct file
or by sock_release() done by sock_alloc_file(). Either way
the caller should not do sock_release() after that point.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now for the abandoned chunks in unsent outq, it would just free the chunks.
Because no tsn is assigned to them yet, there's no need to send fwd tsn to
peer, unlike for the abandoned chunks in sent outq.
The problem is when parts of the msg have been sent and the other frags
are still in unsent outq, if they are abandoned/dropped, the peer would
never get this msg reassembled.
So these frags in unsent outq can't be dropped if this msg already has
outstanding frags.
This patch does the check in sctp_chunk_abandoned and
sctp_prsctp_prune_unsent.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As rfc3758#section-3.1 demands:
A3) When a TSN is "abandoned", if it is part of a fragmented message,
all other TSN's within that fragmented message MUST be abandoned
at the same time.
Besides, if it couldn't handle this, the rest frags would never get
assembled in peer side.
This patch supports it by adding abandoned flag in sctp_datamsg, when
one chunk is being abandoned, set chunk->msg->abandoned as well. Next
time when checking for abandoned, go checking chunk->msg->abandoned
first.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now outstanding_bytes is only increased when appending chunks into one
packet and sending it at 1st time, while decreased when it is about to
move into retransmit queue. It means outstanding_bytes value is already
decreased for all chunks in retransmit queue.
However sctp_prsctp_prune_sent is a common function to check the chunks
in both transmitted and retransmit queue, it decrease outstanding_bytes
when moving a chunk into abandoned queue from either of them.
It could cause outstanding_bytes underflow, as it also decreases it's
value for the chunks in retransmit queue.
This patch fixes it by only updating outstanding_bytes for transmitted
queue when pruning queues for prsctp prio policy, the same fix is also
needed in sctp_check_transmitted.
Fixes: 8dbdf1f5b0 ("sctp: implement prsctp PRIO policy")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d04adf1b35 ("sctp: reset owner sk for data chunks on out queues
when migrating a sock") made a mistake that using 'list' as the param of
list_for_each_entry to traverse the retransmit, sacked and abandoned
queues, while chunks are using 'transmitted_list' to link into these
queues.
It could cause NULL dereference panic if there are chunks in any of these
queues when peeling off one asoc.
So use the chunk member 'transmitted_list' instead in this patch.
Fixes: d04adf1b35 ("sctp: reset owner sk for data chunks on out queues when migrating a sock")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now each stream sched ops is defined in different .c file and
added into the global ops in another .c file, it uses extern
to make this work.
However extern is not good coding style to get them in and
even make C=2 reports errors for this.
This patch adds sctp_sched_ops_xxx_init for each stream sched
ops in their .c file, then get them into the global ops by
calling them when initializing sctp module.
Fixes: 637784ade2 ("sctp: introduce priority based stream scheduler")
Fixes: ac1ed8b82c ("sctp: introduce round robin stream scheduler")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to force SCTP_ERROR_INV_STRM with right type to
fit in sctp_chunk_fail to avoid the sparse error.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing asoc reset, if the sender of the response has already sent some
chunk and increased asoc->next_tsn before the duplicate request comes, the
response will use the old result with an incorrect sender next_tsn.
Better than asoc->next_tsn, asoc->ctsn_ack_point can't be changed after
the sender of the response has performed the asoc reset and before the
peer has confirmed it, and it's value is still asoc->next_tsn original
value minus 1.
This patch sets sender next_tsn for the old result with ctsn_ack_point
plus 1 when processing the duplicate request, to make sure the sender
next_tsn value peer gets will be always right.
Fixes: 692787cef6 ("sctp: implement receiver-side procedures for the SSN/TSN Reset Request Parameter")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when doing asoc reset, it cleans up sacked and abandoned queues
by calling sctp_outq_free where it also cleans up unsent, retransmit
and transmitted queues.
It's safe for the sender of response, as these 3 queues are empty at
that time. But when the receiver of response is doing the reset, the
users may already enqueue some chunks into unsent during the time
waiting the response, and these chunks should not be flushed.
To void the chunks in it would be removed, it moves the queue into a
temp list, then gets it back after sctp_outq_free is done.
The patch also fixes some incorrect comments in
sctp_process_strreset_tsnreq.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it says in rfc6525#section5.1.4, before sending the request,
C2: The sender has either no outstanding TSNs or considers all
outstanding TSNs abandoned.
Prior to this patch, it tried to consider all outstanding TSNs abandoned
by dropping all chunks in all outqs with sctp_outq_free (even including
sacked, retransmit and transmitted queues) when doing this reset, which
is too aggressive.
To make it work gently, this patch will only allow the asoc reset when
the sender has no outstanding TSNs by checking if unsent, transmitted
and retransmit are all empty with sctp_outq_is_empty before sending
and processing the request.
Fixes: 692787cef6 ("sctp: implement receiver-side procedures for the SSN/TSN Reset Request Parameter")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the out stream reset in sctp stream reconf could be done even if
the stream outq is not empty. It means that users can not be sure
since which msg the new ssn will be used.
To make this more synchronous, it shouldn't allow to do out stream
reset until these chunks in unsent outq all are sent out.
This patch checks the corresponding stream outqs when sending and
processing the request . If any of them has unsent chunks in outq,
it will return -EAGAIN instead or send SCTP_STRRESET_IN_PROGRESS
back to the sender.
Fixes: 7f9d68ac94 ("sctp: implement sender-side procedures for SSN Reset Request Parameter")
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in stream reconf part there are still some places using magic
number 2 for each stream number length. To make it more readable,
this patch is to replace them with sizeof(__u16).
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_setsockopt_maxseg user_frag or frag_point can be set with
val >= 8 and val <= SCTP_MAX_CHUNK_LEN. But both checks are incorrect.
val >= 8 means frag_point can even be less than SCTP_DEFAULT_MINSEGMENT.
Then in sctp_datamsg_from_user(), when it's value is greater than cookie
echo len and trying to bundle with cookie echo chunk, the first_len will
overflow.
The worse case is when it's value is equal as cookie echo len, first_len
becomes 0, it will go into a dead loop for fragment later on. In Hangbin
syzkaller testing env, oom was even triggered due to consecutive memory
allocation in that loop.
Besides, SCTP_MAX_CHUNK_LEN is the max size of the whole chunk, it should
deduct the data header for frag_point or user_frag check.
This patch does a proper check with SCTP_DEFAULT_MINSEGMENT subtracting
the sctphdr and datahdr, SCTP_MAX_CHUNK_LEN subtracting datahdr when
setting frag_point via sockopt. It also improves sctp_setsockopt_maxseg
codes.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandar Potapenko while testing the kernel with KMSAN and syzkaller
discovered that in some configurations sctp would leak 4 bytes of
kernel stack.
Working with his reproducer I discovered that those 4 bytes that
are leaked is the scope id of an ipv6 address returned by recvmsg.
With a little code inspection and a shrewd guess I discovered that
sctp_inet6_skb_msgname only initializes the scope_id field for link
local ipv6 addresses to the interface index the link local address
pertains to instead of initializing the scope_id field for all ipv6
addresses.
That is almost reasonable as scope_id's are meaniningful only for link
local addresses. Set the scope_id in all other cases to 0 which is
not a valid interface index to make it clear there is nothing useful
in the scope_id field.
There should be no danger of breaking userspace as the stack leak
guaranteed that previously meaningless random data was being returned.
Fixes: 372f525b495c ("SCTP: Resync with LKSCTP tree.")
History-tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Reported-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when resetting stream, if both in and out flags are set, the info
len can reach:
sizeof(struct sctp_strreset_outreq) + SCTP_MAX_STREAM(65535) +
sizeof(struct sctp_strreset_inreq) + SCTP_MAX_STREAM(65535)
even without duplicated stream no, this value is far greater than the
chunk's max size.
_sctp_make_chunk doesn't do any check for this, which would cause the
skb it allocs is huge, syzbot even reported a crash due to this.
This patch is to check stream reset info len before making reconf
chunk and return EINVAL if the len exceeds chunk's capacity.
Thanks Marcelo and Neil for making this clear.
v1->v2:
- move the check into sctp_send_reset_streams instead.
Fixes: cc16f00f65 ("sctp: add support for generating stream reconf ssn reset request chunk")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dfcb9f4f99 ("sctp: deny peeloff operation on asocs with threads
sleeping on it") fixed the race between peeloff and wait sndbuf by
checking waitqueue_active(&asoc->wait) in sctp_do_peeloff().
But it actually doesn't work, as even if waitqueue_active returns false
the waiting sndbuf thread may still not yet hold sk lock. After asoc is
peeled off, sk is not asoc->base.sk any more, then to hold the old sk
lock couldn't make assoc safe to access.
This patch is to fix this by changing to hold the new sk lock if sk is
not asoc->base.sk, meanwhile, also set the sk in sctp_sendmsg with the
new sk.
With this fix, there is no more race between peeloff and waitbuf, the
check 'waitqueue_active' in sctp_do_peeloff can be removed.
Thanks Marcelo and Neil for making this clear.
v1->v2:
fix it by changing to lock the new sock instead of adding a flag in asoc.
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_sendmsg sctp_wait_for_sndbuf could schedule out without
holding sock sk. It means the current asoc can be freed elsewhere,
like when receiving an abort packet.
If the asoc is just created in sctp_sendmsg and sctp_wait_for_sndbuf
returns err, the asoc will be freed again due to new_asoc is not nil.
An use-after-free issue would be triggered by this.
This patch is to fix it by setting new_asoc with nil if the asoc is
already dead when cpu schedules back, so that it will not be freed
again in sctp_sendmsg.
v1->v2:
set new_asoc as nil in sctp_sendmsg instead of sctp_wait_for_sndbuf.
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to returnerror code -ENOMEM from the sctp_make_strreset_addstrm()
error handling case instead of 0. 'retval' can be overwritten to 0 after
call sctp_stream_alloc_out().
Fixes: e090abd0d8 ("sctp: factor out stream->out allocation")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
They are there since very beginning.
Note after this patch, there still one warning left in
sctp_outq_flush():
sctp_chunk_fail(chunk, SCTP_ERROR_INV_STRM)
Since it has been moved to sctp_stream_outq_migrate on net-next,
to avoid the extra job when merging net-next to net, I will post
the fix for it after the merging is done.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
Commit d4d6fb5787 ("sctp: Try not to change a_rwnd when faking a
SACK from SHUTDOWN.") expected to use the peers old rwnd and add
our flight size to the a_rwnd. But with the wrong Endian, it may
not work as well as expected.
So fix it by converting to the right value.
Fixes: d4d6fb5787 ("sctp: Try not to change a_rwnd when faking a SACK from SHUTDOWN.")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
They are introduced by not aware of Endian for the port when
coding transport rhashtable patches.
Fixes: 7fda702f93 ("sctp: use new rhlist interface on sctp transport rhashtable")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
They are introduced by not aware of Endian when coding stream
reconf patches.
Since commit c0d8bab6ae ("sctp: add get and set sockopt for
reconf_enable") enabled stream reconf feature for users, the
Fixes tag below would use it.
Fixes: c0d8bab6ae ("sctp: add get and set sockopt for reconf_enable")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when migrating sock to another one in sctp_sock_migrate(), it only
resets owner sk for the data in receive queues, not the chunks on out
queues.
It would cause that data chunks length on the sock is not consistent
with sk sk_wmem_alloc. When closing the sock or freeing these chunks,
the old sk would never be freed, and the new sock may crash due to
the overflow sk_wmem_alloc.
syzbot found this issue with this series:
r0 = socket$inet_sctp()
sendto$inet(r0)
listen(r0)
accept4(r0)
close(r0)
Although listen() should have returned error when one TCP-style socket
is in connecting (I may fix this one in another patch), it could also
be reproduced by peeling off an assoc.
This issue is there since very beginning.
This patch is to reset owner sk for the chunks on out queues so that
sk sk_wmem_alloc has correct value after accept one sock or peeloff
an assoc to one sock.
Note that when resetting owner sk for chunks on outqueue, it has to
sctp_clear_owner_w/skb_orphan chunks before changing assoc->base.sk
first and then sctp_set_owner_w them after changing assoc->base.sk,
due to that sctp_wfree and it's callees are using assoc->base.sk.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-sctp@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9b97420228 ("sctp: support ipv6 nonlocal bind")
introduced support for the above options as v4 sctp did,
so patched sctp_v6_available().
In the v4 implementation it's enough, because
sctp_inet_bind_verify() just returns with sctp_v4_available().
However sctp_inet6_bind_verify() has an extra check before that
for link-local scope_id, which won't respect the above options.
Added the checks before calling ipv6_chk_addr(), but
not before the validation of scope_id.
before (w/ both options):
./v6test fe80::10 sctp
bind failed, errno: 99 (Cannot assign requested address)
./v6test fe80::10 tcp
bind success, errno: 0 (Success)
after (w/ both options):
./v6test fe80::10 sctp
bind success, errno: 0 (Success)
Signed-off-by: Laszlo Toth <laszlth@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp processes icmp redirect packet in sctp_icmp_redirect where
it calls sctp_transport_dst_check in which tp->dst can be released.
The problem is before calling sctp_transport_dst_check, it doesn't
check sock_owned_by_user, which means tp->dst could be freed while
a process is accessing it with owning the socket.
An use-after-free issue could be triggered by this.
This patch is to fix it by checking sock_owned_by_user before calling
sctp_transport_dst_check in sctp_icmp_redirect, so that it would not
release tp->dst if users still hold sock lock.
Besides, the same issue fixed in commit 45caeaa5ac ("dccp/tcp: fix
routing redirect race") on sctp also needs this check.
Fixes: 55be7a9c60 ("ipv4: Add redirect support to all protocol icmp error handlers")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when peeling off an association to the sock in another netns, all
transports in this assoc are not to be rehashed and keep use the old
key in hashtable.
As a transport uses sk->net as the hash key to insert into hashtable,
it would miss removing these transports from hashtable due to the new
netns when closing the sock and all transports are being freeed, then
later an use-after-free issue could be caused when looking up an asoc
and dereferencing those transports.
This is a very old issue since very beginning, ChunYu found it with
syzkaller fuzz testing with this series:
socket$inet6_sctp()
bind$inet6()
sendto$inet6()
unshare(0x40000000)
getsockopt$inet_sctp6_SCTP_GET_ASSOC_ID_LIST()
getsockopt$inet_sctp6_SCTP_SOCKOPT_PEELOFF()
This patch is to block this call when peeling one assoc off from one
netns to another one, so that the netns of all transport would not
go out-sync with the key in hashtable.
Note that this patch didn't fix it by rehashing transports, as it's
difficult to handle the situation when the tuple is already in use
in the new netns. Besides, no one would like to peel off one assoc
to another netns, considering ipaddrs, ifaces, etc. are usually
different.
Reported-by: ChunYu Wang <chunwang@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The array sctp_sched_ops is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'sctp_sched_ops' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces RFC Draft ndata section 3.2 Priority Based
Scheduler (SCTP_SS_RR).
Works by maintaining a list of enqueued streams and tracking the last
one used to send data. When the datamsg is done, it switches to the next
stream.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-sctp-ndata-13
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces RFC Draft ndata section 3.4 Priority Based
Scheduler (SCTP_SS_PRIO).
It works by having a struct sctp_stream_priority for each priority
configured. This struct is then enlisted on a queue ordered per priority
if, and only if, there is a stream with data queued, so that dequeueing
is very straightforward: either finish current datamsg or simply dequeue
from the highest priority queued, which is the next stream pointed, and
that's it.
If there are multiple streams assigned with the same priority and with
data queued, it will do round robin amongst them while respecting
datamsgs boundaries (when not using idata chunks), to be reasonably
fair.
We intentionally don't maintain a list of priorities nor a list of all
streams with the same priority to save memory. The first would mean at
least 2 other pointers per priority (which, for 1000 priorities, that
can mean 16kB) and the second would also mean 2 other pointers but per
stream. As SCTP supports up to 65535 streams on a given asoc, that's
1MB. This impacts when giving a priority to some stream, as we have to
find out if the new priority is already being used and if we can free
the old one, and also when tearing down.
The new fields in struct sctp_stream_out_ext and sctp_stream are added
under a union because that memory is to be shared with other schedulers.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-sctp-ndata-13
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
