Get rid of device tree property "awinic,display-rows". The property
value actually means number of current switches and depends on how LEDs
are connected to the device. It should be calculated manually by max
used LED number. In the same way it is computed automatically now.
Max used LED is taken from LED definition subnodes.
Signed-off-by: George Stark <gnstark@salutedevices.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20231125200519.1750-5-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
HWEN is hardware control, which is used for enable/disable aw200xx chip.
It's high active, internally pulled down to GND.
After HWEN pin set high the chip begins to load the OTP information,
which takes 200us to complete. About 200us wait time is needed for
internal oscillator startup and display SRAM initialization. After
display SRAM initialization, the registers in page 1 to page 5 can be
configured via i2c interface.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Link: https://lore.kernel.org/r/20231125200519.1750-3-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
If write only DIM value to the page 4, LED brightness will not be
updated, as both DIM and FADE need to be written to the page 4.
Therefore, write DIM to the page 1.
Fixes: 36a87f371b ("leds: Add AW20xx driver")
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20231125200519.1750-2-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
The serial tty interface also supports additional input signals, that
can also be evaluated within this trigger. This change is adding the
following additional input sources, which could be controlled
via the '/sys/class/<leds>/' sysfs interface.
Explanation:
DCE = Data Communication Equipment (Modem)
DTE = Data Terminal Equipment (Computer)
- cts:
DCE is ready to accept data from the DTE (CTS = Clear To Send). If
the line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate CTS.
If set to 1, the LED will evaluate CTS.
- dsr:
DCE is ready to receive and send data (DSR = Data Set Ready). If the
line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate DSR.
If set to 1, the LED will evaluate DSR.
- dcd:
DTE is receiving a carrier from the DCE (DCD = Data Carrier Detect).
If the line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate DCD.
If set to 1, the LED will evaluate DCD.
- rng:
DCE has detected an incoming ring signal on the telephone line
(RNG = Ring Indicator). If the line state is detected, the LED is
switched on.
If set to 0 (default), the LED will not evaluate RNG.
If set to 1, the LED will evaluate RNG.
Also add an invert flag on LED blink, so that the LED blinks in the
correct order.
* If one off the new enabled input signals are evaluatet as 'enabled',
and data are transmitted, then the LED should first blink 'off' and
then 'on' (invert).
* If all the new enabled input signals are evaluatet as 'disabled',
and data are transmitted, then the LED should first blink 'on' and
then 'off'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Maarten Brock <m.brock@vanmierlo.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-5-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
Until now, the LED blinks when data is sent via the tty (rx/tx).
This is not configurable.
This change adds the possibility to make the indication for the direction
of the transmitted data independently controllable via the new rx and
tx sysfs entries.
- rx:
Signal reception (rx) of data on the named tty device.
If set to 0, the LED will not blink on reception.
If set to 1 (default), the LED will blink on reception.
- tx:
Signal transmission (tx) of data on the named tty device.
If set to 0, the LED will not blink on transmission.
If set to 1 (default), the LED will blink on transmission.
This new sysfs entry are on by default. Thus the trigger behaves as
before this change.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-4-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
With this commit, the mutex handling is replaced by the completion
handling. When handling mutex, it must always be ensured that the held
mutex is also released again. This is more error-prone should the number
of code paths increase.
This is a preparatory commit to make the trigger more configurable via
additional sysfs parameters. With this change, the worker always runs and
is no longer stopped if no ttyname is set.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-3-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
One error path already used dev_err_probe(). Adapt the other error paths
that emit an error message to also use this function for consistency and
slightly simplified code.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231126095230.683204-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
With pwmchip_remove() being automatically called after switching to
devm_pwmchip_add() the remove function can be dropped completely. Yay!
With lpg_remove() gone there is no user of the platform device's drvdata
left, so platform_set_drvdata() can be dropped from .probe(), too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231126095230.683204-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
The ttyname buffer for the ledtrig_tty_data struct is allocated in the
sysfs ttyname_store() function. This buffer must be released on trigger
deactivation. This was missing and is thus a memory leak.
While we are at it, the TTY handler in the ledtrig_tty_data struct should
also be returned in case of the trigger deactivation call.
Cc: stable@vger.kernel.org
Fixes: fd4a641ac8 ("leds: trigger: implement a tty trigger")
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127081621.774866-1-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231103195310.948327-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
sscanf() is a heavy one and moreover requires additional boundary checks.
Convert driver to use kstrtou8() in gpio_trig_inverted_store().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231103195310.948327-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
gpiod_get_optional() and currently used fwnode_gpiod_get_index()
are both wrappers against the same engine internally. Since we
have a pointer to struct device there is no reason to use fwnode
type of GPIO call. So, replace the current fwnode call by respective
gpiod ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231103195310.948327-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
The AW2013 driver uses devm_regmap_init_i2c, so REGMAP_I2C needs to
be selected.
Otherwise build process may fail with:
ld: drivers/leds/leds-aw2013.o: in function `aw2013_probe':
leds-aw2013.c:345: undefined reference to `__devm_regmap_init_i2c'
Signed-off-by: Dang Huynh <danct12@riseup.net>
Acked-by: Nikita Travkin <nikita@trvn.ru>
Fixes: 59ea3c9faf ("leds: add aw2013 driver")
Link: https://lore.kernel.org/r/20231103114203.1108922-1-danct12@riseup.net
Signed-off-by: Lee Jones <lee@kernel.org>
Some Allwinner sunxi SoCs, starting with the A100, contain an LED
controller designed to drive RGB LED pixels. Add a driver for it using
the multicolor LED framework, and with LEDs defined in the device tree.
Acked-by: Guo Ren <guoren@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20231029212738.7871-3-samuel@sholland.org
Signed-off-by: Lee Jones <lee@kernel.org>
The register-bit-led binding now also supports 'reg' in addition to
'offset' for the register address. Add support to the driver to get the
address from 'reg'.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231025190619.881090-2-robh@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
This contains a few fixes and a bunch of cleanups, a lot of which is in
preparation for Uwe's character device support that may be ready in time
for the next merge window.
-----BEGIN PGP SIGNATURE-----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=S2DI
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains a few fixes and a bunch of cleanups, a lot of which is
in preparation for Uwe's character device support that may be ready in
time for the next merge window"
* tag 'pwm/for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: samsung: Document new member .channel in struct samsung_pwm_chip
pwm: bcm2835: Add support for suspend/resume
pwm: brcmstb: Checked clk_prepare_enable() return value
pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
pwm: pxa: Explicitly include correct DT includes
pwm: cros-ec: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: samsung: Consistently use the same name for driver data
pwm: vt8500: Simplify using devm functions
pwm: sprd: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: sprd: Provide a helper to cast a chip to driver data
pwm: spear: Simplify using devm functions
pwm: mtk-disp: Simplify using devm_pwmchip_add()
pwm: imx-tpm: Simplify using devm functions
pwm: brcmstb: Simplify using devm functions
pwm: bcm2835: Simplify using devm functions
pwm: bcm-iproc: Simplify using devm functions
pwm: Adapt sysfs API documentation to reality
pwm: dwc: add PWM bit unset in get_state call
pwm: dwc: make timer clock configurable
pwm: dwc: split pci out of core driver
...
- Add support for a bunch more colours
- New Drivers
- Add support for Kinetic KTD2026/7 RGB/White LEDs
- New Functionality
- Add support for device to enter HW Controlled Mode to Turris Omnia LEDs
- Add support for HW Gamma Correction to Turris Omnia LEDs
- Fix-ups
- Apply new __counted_by() annotation to several data structures containing flexible arrays
- Rid the return value from Platform's .remove() operation
- Use *_cansleep() variants for instances were threads can sleep
- Improve the semantics when setting the brightness
- Generic clean-ups; code reduction, coding style, standard patterns
- Replace strncpy() with strscpy()
- Fix-up / add various documentation
- Re-author the GPIO associated Trigger to use trigger-sources
- Move to using standard APIs and helpers
- Improve error checking
- Stop using static GPIO bases
- Bug Fixes
- Fix Pointer to Enum casing warnings
- Do not pretend that I2C backed device supports SMBUS
- Ensure PWM LEDs are extinguished when disabled, rather than held in a state
- Fix 'output may be truncated' warnings
-----BEGIN PGP SIGNATURE-----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=XYXV
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Core Frameworks:
- Add support for a bunch more colours
New Drivers:
- Add support for Kinetic KTD2026/7 RGB/White LEDs
New Functionality:
- Add support for device to enter HW Controlled Mode to Turris Omnia
LEDs
- Add support for HW Gamma Correction to Turris Omnia LEDs
Fix-ups:
- Apply new __counted_by() annotation to several data structures
containing flexible arrays
- Rid the return value from Platform's .remove() operation
- Use *_cansleep() variants for instances were threads can sleep
- Improve the semantics when setting the brightness
- Generic clean-ups; code reduction, coding style, standard patterns
- Replace strncpy() with strscpy()
- Fix-up / add various documentation
- Re-author the GPIO associated Trigger to use trigger-sources
- Move to using standard APIs and helpers
- Improve error checking
- Stop using static GPIO bases
Bug Fixes:
- Fix Pointer to Enum casing warnings
- Do not pretend that I2C backed device supports SMBUS
- Ensure PWM LEDs are extinguished when disabled, rather than held in
a state
- Fix 'output may be truncated' warnings"
* tag 'leds-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (43 commits)
leds: lp5521: Add an error check in lp5521_post_init_device
leds: gpio: Update headers
leds: gpio: Remove unneeded assignment
leds: gpio: Move temporary variable for struct device to gpio_led_probe()
leds: gpio: Refactor code to use devm_gpiod_get_index_optional()
leds: gpio: Utilise PTR_ERR_OR_ZERO()
leds: gpio: Keep driver firmware interface agnostic
leds: core: Refactor led_update_brightness() to use standard pattern
leds: turris-omnia: Fix brightness setting and trigger activating
leds: sc27xx: Move mutex_init() down
leds: trigger: netdev: Move size check in set_device_name
leds: Add ktd202x driver
dt-bindings: leds: Add Kinetic KTD2026/2027 LED
leds: core: Add more colors from DT bindings to led_colors
dt-bindings: leds: Last color ID is now 14 (LED_COLOR_ID_LIME)
leds: tca6507: Don't use fixed GPIO base
leds: lp3952: Convert to use maple tree register cache
leds: lm392x: Convert to use maple tree register cache
leds: aw200xx: Convert to use maple tree register cache
leds: lm3601x: Convert to use maple tree register cache
...
Instead of checking for the specific error codes, replace
devm_gpiod_get_index() with devm_gpiod_get_index_optional().
In this case we just return all errors to the caller and
simply check for NULL in case if legacy GPIO is being used.
As the result the code is easier to read and maintain.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231016161005.1471768-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
The of.h is used as a proxy to mod_devicetable, replace former by
latter.
The commit 2d6180147e ("leds: gpio: Configure per-LED pin control")
added yet another unneeded OF APIs. Replace with direct use of fwnode.
Altogether this makes driver agnostic to the firmware interface in use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231016161005.1471768-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
The standard conditional pattern is to check for errors first and
bail out if any. Refactor led_update_brightness() accordingly.
While at it, drop unneeded assignment and return 0 unconditionally
on success.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Denis Osterland-Heim <denis.osterland@diehl.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231016153051.1409074-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
I have improperly refactored commits
4d5ed2621c24 ("leds: turris-omnia: Make set_brightness() more efficient")
and
aaf38273cf76 ("leds: turris-omnia: Support HW controlled mode via private trigger")
after Lee requested a change in API semantics of the new functions I
introduced in commit
28350bc0ac77 ("leds: turris-omnia: Do not use SMBUS calls").
Before the change, the function omnia_cmd_write_u8() returned 0 on
success, and afterwards it returned a positive value (number of bytes
written). The latter version was applied, but the following commits did
not properly account for this change.
This results in non-functional LED's .brightness_set_blocking() and
trigger's .activate() methods.
The main reasoning behind the semantics change was that read/write
methods should return the number of read/written bytes on success.
It was pointed to me [1] that this is not always true (for example the
regmap API does not do so), and since the driver never uses this number
of read/written bytes information, I decided to fix this issue by
changing the functions to the original semantics (return 0 on success).
[1] https://lore.kernel.org/linux-gpio/ZQnn+Gi0xVlsGCYA@smile.fi.intel.com/
Fixes: 28350bc0ac77 ("leds: turris-omnia: Do not use SMBUS calls")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20231016141538.30037-1-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Move the mutex_init() to avoid redundant mutex_destroy() calls after
that for each time the probe fails.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231013022010.854367-1-chunyan.zhang@unisoc.com
Signed-off-by: Lee Jones <lee@kernel.org>
GCC 13.2 complains about array subscript 17 is above array bounds of
'char[16]' with IFNAMSIZ set to 16.
The warning is correct but this scenario is impossible.
set_device_name is called by device_name_store (store sysfs entry) and
netdev_trig_activate.
device_name_store already check if size is >= of IFNAMSIZ and return
-EINVAL. (making the warning scenario impossible)
netdev_trig_activate works on already defined interface, where the name
has already been checked and should already follow the condition of
strlen() < IFNAMSIZ.
Aside from the scenario being impossible, set_device_name can be
improved to both mute the warning and make the function safer.
To make it safer, move size check from device_name_store directly to
set_device_name and prevent any out of bounds scenario.
Cc: stable@vger.kernel.org
Fixes: 28a6a2ef18 ("leds: trigger: netdev: refactor code setting device name")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309192035.GTJEEbem-lkp@intel.com/
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20231007131042.15032-1-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
The colors are already part of DT bindings. Make sure the kernel is
able to convert them to strings.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20231008144014.1180334-1-megi@xff.cz
Signed-off-by: Lee Jones <lee@kernel.org>
First of all, the fixed GPIO base is source of troubles and
it doesn't scale. Second, there is no in-kernel user of this
base, so drop it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231002135629.2605462-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-4-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-3-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-2-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230929-leds-maple-v1-1-ba5f9dcb1e75@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
By providing a GPIO line as "trigger-sources" in the FWNODE
(such as from the device tree) and combining with the
GPIO trigger, we can support a GPIO LED trigger in a natural
way from the hardware description instead of using the
custom sysfs and deprecated global GPIO numberspace.
Example:
gpio: gpio@0 {
compatible "my-gpio";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
#trigger-source-cells = <2>;
};
leds {
compatible = "gpio-leds";
led-my-gpio {
label = "device:blue:myled";
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
default-state = "off";
linux,default-trigger = "gpio";
trigger-sources = <&gpio 1 GPIO_ACTIVE_HIGH>;
};
};
Make this the norm, unmark the driver as broken.
Delete the sysfs handling of GPIOs.
Since GPIO descriptors inherently can describe inversion,
the inversion handling can just be deleted.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230926-gpio-led-trigger-dt-v2-3-e06e458b788e@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Some cleanups:
* Remove the trailing comma in the terminator entry for the OF
table making code robust against (theoretical) misrebases or other
similar things where the new entry goes _after_ the termination without
the compiler noticing.
* Drop a space from terminator entry for ID table.
While at it, move OF/ID table near to the user.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230923171921.53503-3-biju.das.jz@bp.renesas.com
Signed-off-by: Lee Jones <lee@kernel.org>
Convert enum->pointer for data in the match tables, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Replace enum->struct *pca955x_chipdefs for data in the match table.
Simplify the probe() by replacing device_get_match_data() and ID lookup
for retrieving data by i2c_get_match_data().
While at it, add const definition to pca955x_chipdefs[].
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230923171921.53503-2-biju.das.jz@bp.renesas.com
Signed-off-by: Lee Jones <lee@kernel.org>
`strncpy` is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect `dest` to be NUL-terminated due to its use with dev_err.
lp3952_get_label()'s dest argument is priv->leds[i].name:
| acpi_ret = lp3952_get_label(&priv->client->dev, led_name_hdl[i],
| priv->leds[i].name);
... which is then assigned to:
| priv->leds[i].cdev.name = priv->leds[i].name;
... which is used with a format string
| dev_err(&priv->client->dev,
| "couldn't register LED %s\n",
| priv->leds[i].cdev.name);
There is no indication that NUL-padding is required but if it is let's
opt for strscpy_pad.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230922-strncpy-drivers-leds-leds-lp3952-c-v1-1-4941d6f60ca4@google.com
Signed-off-by: Lee Jones <lee@kernel.org>
In order to teach the compiler that 'trig->name' will never be truncated,
we need to tell it that 'cpu' is not negative.
When building with W=1, this fixes the following warnings:
drivers/leds/trigger/ledtrig-cpu.c: In function ‘ledtrig_cpu_init’:
drivers/leds/trigger/ledtrig-cpu.c:155:56: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 5 [-Werror=format-truncation=]
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~
drivers/leds/trigger/ledtrig-cpu.c:155:52: note: directive argument in the range [-2147483648, 7]
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~~~~~~
drivers/leds/trigger/ledtrig-cpu.c:155:17: note: ‘snprintf’ output between 5 and 15 bytes into a destination of size 8
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8f88731d05 ("led-triggers: create a trigger for CPU activity")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/3f4be7a99933cf8566e630da54f6ab913caac432.1695453322.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
Disabling a PWM (i.e. calling pwm_apply_state with .enabled = false)
gives no guarantees what the PWM output does. It might freeze where it
currently is, or go in a High-Z state or drive the active or inactive
state, it might even continue to toggle.
To ensure that the LED gets really disabled, don't disable the PWM even
when .duty_cycle is zero.
This fixes disabling a leds-pwm LED on i.MX28. The PWM on this SoC is
one of those that freezes its output on disable, so if you disable an
LED that is full on, it stays on. If you disable a LED with half
brightness it goes off in 50% of the cases and full on in the other 50%.
Fixes: 41c42ff5db ("leds: simple driver for pwm driven LEDs")
Reported-by: Rogan Dawes <rogan@dawes.za.net>
Reported-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230922192834.1695727-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
If the MCU on Turris Omnia is running newer firmware versions, the LED
controller supports RGB gamma correction (and enables it by default for
newer boards).
Determine whether the gamma correction setting feature is supported and
add the ability to set it via sysfs attribute file.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-5-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for enabling MCU controlled mode of the Turris Omnia LEDs
via a LED private trigger called "omnia-mcu". Recall that private LED
triggers will only be listed in the sysfs trigger file for LEDs that
support them (currently there is no user of this mechanism).
When in MCU controlled mode, the user can still set LED color, but the
blinking is done by MCU, which does different things for different LEDs:
- WAN LED is blinked according to the LED[0] pin of the WAN PHY
- LAN LEDs are blinked according to the LED[0] output of the
corresponding port of the LAN switch
- PCIe LEDs are blinked according to the logical OR of the MiniPCIe port
LED pins
In the future I want to make the netdev trigger to transparently offload
the blinking to the HW if user sets compatible settings for the netdev
trigger (for LEDs associated with network devices).
There was some work on this already, and hopefully we will be able to
complete it sometime, but for now there are still multiple blockers for
this, and even if there weren't, we still would not be able to configure
HW controlled mode for the LEDs associated with MiniPCIe ports.
In the meantime let's support HW controlled mode via the private LED
trigger mechanism. If, in the future, we manage to complete the netdev
trigger offloading, we can still keep this private trigger for backwards
compatibility, if needed.
We also set "omnia-mcu" to cdev->default_trigger, so that the MCU keeps
control until the user first wants to take over it. If a different
default trigger is specified in device-tree via the
'linux,default-trigger' property, LED class will overwrite
cdev->default_trigger, and so the DT property will be respected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-4-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Implement caching of the LED color and state values that are sent to MCU
in order to make the set_brightness() operation more efficient by
avoiding I2C transactions which are not needed.
On Turris Omnia's MCU, which acts as the RGB LED controller, each LED
has a RGB color, and a ON/OFF state, which are configurable via I2C
commands CMD_LED_COLOR and CMD_LED_STATE.
The CMD_LED_COLOR command sends 5 bytes and the CMD_LED_STATE command 2
bytes over the I2C bus, which operates at 100 kHz. With I2C overhead
this allows ~1670 color changing commands and ~3200 state changing
commands per second (or around 1000 color + state changes per second).
This may seem more than enough, but the issue is that the I2C bus is
shared with another peripheral, the MCU. The MCU exposes an interrupt
interface, and it can trigger hundreds of interrupts per second. Each
time, we need to read the interrupt state register over this I2C bus.
Whenever we are sending a LED color/state changing command, the
interrupt reading is waiting.
Currently, every time LED brightness or LED multi intensity is changed,
we send a CMD_LED_STATE command, and if the computed color (brightness
adjusted multi_intensity) is non-zero, we also send a CMD_LED_COLOR
command.
Consider for example the situation when we have a netdev trigger enabled
for a LED. The netdev trigger does not change the LED color, only the
brightness (either to 0 or to currently configured brightness), and so
there is no need to send the CMD_LED_COLOR command. But each change of
brightness to 0 sends one CMD_LED_STATE command, and each change of
brightness to max_brightness sends one CMD_LED_STATE command and one
CMD_LED_COLOR command:
set_brightness(0) -> CMD_LED_STATE
set_brightness(255) -> CMD_LED_STATE + CMD_LED_COLOR
(unnecessary)
We can avoid the unnecessary I2C transactions if we cache the values of
state and color that are sent to the controller. If the color does not
change from the one previously sent, there is no need to do the
CMD_LED_COLOR I2C transaction, and if the state does not change, there
is no need to do the CMD_LED_STATE transaction.
Because we need to make sure that our cached values are consistent with
the controller state, add explicit setting of the LED color to white at
probe time (this is the default setting when MCU resets, but does not
necessarily need to be the case, for example if U-Boot played with the
LED colors).
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-3-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The leds-turris-omnia driver uses three function for I2C access:
- i2c_smbus_write_byte_data() and i2c_smbus_read_byte_data(), which
cause an emulated SMBUS transfer,
- i2c_master_send(), which causes an ordinary I2C transfer.
The Turris Omnia MCU LED controller is not semantically SMBUS, it
operates as a simple I2C bus. It does not implement any of the SMBUS
specific features, like PEC, or procedure calls, or anything. Moreover
the I2C controller driver also does not implement SMBUS, and so the
emulated SMBUS procedure from drivers/i2c/i2c-core-smbus.c is used for
the SMBUS calls, which gives an unnecessary overhead.
When I first wrote the driver, I was unaware of these facts, and I
simply used the first function that worked.
Drop the I2C SMBUS calls and instead use simple I2C transfers.
Fixes: 089381b27a ("leds: initial support for Turris Omnia LEDs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-2-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
