Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Jon Maloy jon.maloy@ericsson.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Selecting and explicitly configuring a TIPC node identity may be
unwanted in some cases.
In this commit we introduce a default setting if the identity has not
been set at the moment the first bearer is enabled. We do this by
using a raw copy of a unique identifier from the used interface: MAC
address in the case of an L2 bearer, IPv4/IPv6 address in the case
of a UDP bearer.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a 32-bit node address is generated from a 128-bit identifier,
there is a risk of collisions which must be discovered and handled.
We do this as follows:
- We don't apply the generated address immediately to the node, but do
instead initiate a 1 sec trial period to allow other cluster members
to discover and handle such collisions.
- During the trial period the node periodically sends out a new type
of message, DSC_TRIAL_MSG, using broadcast or emulated broadcast,
to all the other nodes in the cluster.
- When a node is receiving such a message, it must check that the
presented 32-bit identifier either is unused, or was used by the very
same peer in a previous session. In both cases it accepts the request
by not responding to it.
- If it finds that the same node has been up before using a different
address, it responds with a DSC_TRIAL_FAIL_MSG containing that
address.
- If it finds that the address has already been taken by some other
node, it generates a new, unused address and returns it to the
requester.
- During the trial period the requesting node must always be prepared
to accept a failure message, i.e., a message where a peer suggests a
different (or equal) address to the one tried. In those cases it
must apply the suggested value as trial address and restart the trial
period.
This algorithm ensures that in the vast majority of cases a node will
have the same address before and after a reboot. If a legacy user
configures the address explicitly, there will be no trial period and
messages, so this protocol addition is completely backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add a 128-bit node identity, as an alternative to the currently used
32-bit node address.
For the sake of compatibility and to minimize message header changes
we retain the existing 32-bit address field. When not set explicitly by
the user, this field will be filled with a hash value generated from the
much longer node identity, and be used as a shorthand value for the
latter.
We permit either the address or the identity to be set by configuration,
but not both, so when the address value is set by a legacy user the
corresponding 128-bit node identity is generated based on the that value.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation to changing the addressing structure of TIPC we replace
all direct accesses to the tipc_net::own_addr field with the function
dedicated for this, tipc_own_addr().
There are no changes to program logics in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The removal of an internal structure of the node address has an unwanted
side effect.
- Currently, if a user is sending an anycast message with destination
domain 0, the tipc_namebl_translate() function will use the 'closest-
first' algorithm to first look for a node local destination, and only
when no such is found, will it resort to the cluster global 'round-
robin' lookup algorithm.
- Current users can get around this, and enforce unconditional use of
global round-robin by indicating a destination as Z.0.0 or Z.C.0.
- This option disappears when we make the node address flat, since the
lookup algorithm has no way of recognizing this case. So, as long as
there are node local destinations, the algorithm will always select
one of those, and there is nothing the sender can do to change this.
We solve this by eliminating the 'closest-first' option, which was never
a good idea anyway, for non-legacy users, but only for those. To
distinguish between legacy users and non-legacy users we introduce a new
flag 'legacy_addr_format' in struct tipc_core, to be set when the user
configures a legacy-style Z.C.N node address. Hence, when a legacy user
indicates a zero lookup domain 'closest-first' is selected, and in all
other cases we use 'round-robin'.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nominally, TIPC organizes network nodes into a three-level network
hierarchy consisting of the levels 'zone', 'cluster' and 'node'. This
hierarchy is reflected in the node address format, - it is sub-divided
into an 8-bit zone id, and 12 bit cluster id, and a 12-bit node id.
However, the 'zone' and 'cluster' levels have in reality never been
fully implemented,and never will be. The result of this has been
that the first 20 bits the node identity structure have been wasted,
and the usable node identity range within a cluster has been limited
to 12 bits. This is starting to become a problem.
In the following commits, we will need to be able to connect between
nodes which are using the whole 32-bit value space of the node address.
We therefore remove the restrictions on which values can be assigned
to node identity, -it is from now on only a 32-bit integer with no
assumed internal structure.
Isolation between clusters is now achieved only by setting different
values for the 'network id' field used during neighbor discovery, in
practice leading to the latter becoming the new cluster identity.
The rules for accepting discovery requests/responses from neighboring
nodes now become:
- If the user is using legacy address format on both peers, reception
of discovery messages is subject to the legacy lookup domain check
in addition to the cluster id check.
- Otherwise, the discovery request/response is always accepted, provided
both peers have the same network id.
This secures backwards compatibility for users who have been using zone
or cluster identities as cluster separators, instead of the intended
'network id'.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To facilitate the coming changes in the neighbor discovery functionality
we make some renaming and refactoring of that code. The functional changes
in this commit are trivial, e.g., that we move the message sending call in
tipc_disc_timeout() outside the spinlock protected region.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for the next commits we try to reduce the footprint of
the function tipc_enable_bearer(), while hopefully making is simpler to
follow.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when tipc is unable to queue a received message on a
socket, the message is rejected back to the sender with error
TIPC_ERR_OVERLOAD. However, the application on this socket
has no knowledge about these discards.
In this commit, we try to step the sk_drops counter when tipc
is unable to queue a received message. Export sk_drops
using tipc socket diagnostics.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds socket diagnostics capability for AF_TIPC in netlink
family NETLINK_SOCK_DIAG in a new kernel module (diag.ko).
The following are key design considerations:
- config TIPC_DIAG has default y, like INET_DIAG.
- only requests with flag NLM_F_DUMP is supported (dump all).
- tipc_sock_diag_req message is introduced to send filter parameters.
- the response attributes are of TLV, some nested.
To avoid exposing data structures between diag and tipc modules and
avoid code duplication, the following additions are required:
- export tipc_nl_sk_walk function to reuse socket iterator.
- export tipc_sk_fill_sock_diag to fill the tipc diag attributes.
- create a sock_diag response message in __tipc_add_sock_diag defined
in diag.c and use the above exported tipc_sk_fill_sock_diag
to fill response.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current socket iterator function tipc_nl_sk_dump, handles socket
locks and calls __tipc_nl_add_sk for each socket.
To reuse this logic in sock_diag implementation, we do minor
modifications to make these functions generic as described below.
In this commit, we add a two new functions __tipc_nl_sk_walk,
__tipc_nl_add_sk_info and modify tipc_nl_sk_dump, __tipc_nl_add_sk
accordingly.
In __tipc_nl_sk_walk we:
1. acquire and release socket locks
2. for each socket, execute the specified callback function
In __tipc_nl_add_sk we:
- Move the netlink attribute insertion to __tipc_nl_add_sk_info.
tipc_nl_sk_dump calls tipc_nl_sk_walk with __tipc_nl_add_sk as argument.
sock_diag will use these generic functions in a later commit.
There is no functional change in this commit.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We rename some lists and fields in struct publication both to make
the naming more consistent and to better reflect their roles. We
also update the descriptions of those lists.
node_list -> local_publ
cluster_list -> all_publ
pport_list -> binding_sock
ref -> port
There are no functional changes in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of struct publication can be reduced further. Membership in
lists 'nodesub_list' and 'local_list' is mutually exlusive, in that
remote publications use the former and local publications the latter.
We replace the two lists with one single, named 'binding_node' which
reflects what it really is.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a further consequence of the previous commits, we can also remove
the member 'zone_list 'in struct name_info and struct publication.
Instead, we now let the member cluster_list take over the role a
container of all publications of a given <type,lower, upper>.
We also remove the counters for the size of those lists, since
they don't serve any purpose.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a consequence of the previous commit we nan now eliminate zone scope
related lists in the name table. We start with name_table::publ_list[3],
which can now be replaced with two lists, one for node scope publications
and one for cluster scope publications.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Publications for TIPC_CLUSTER_SCOPE and TIPC_ZONE_SCOPE are in all
aspects handled the same way, both on the publishing node and on the
receiving nodes.
Despite previous ambitions to the contrary, this is never going to change,
so we take the conseqeunce of this and obsolete TIPC_ZONE_SCOPE and related
macros/functions. Whenever a user is doing a bind() or a sendmsg() attempt
using ZONE_SCOPE we translate this internally to CLUSTER_SCOPE, while we
remain compatible with users and remote nodes still using ZONE_SCOPE.
Furthermore, the non-formalized scope value 0 has always been permitted
for use during lookup, with the same meaning as ZONE_SCOPE/CLUSTER_SCOPE.
We now permit it even as binding scope, but for compatibility reasons we
choose to not change the value of TIPC_CLUSTER_SCOPE.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC looks concentrated in itself, and other pernet_operations
seem not touching its entities.
tipc_net_ops look pernet-divided, and they should be safe to
be executed in parallel for several net the same time.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 60c2530696 ("tipc: fix race between poll() and
setsockopt()") we introduced a pointer from struct tipc_group to the
'group_is_connected' flag in struct tipc_sock, so that this field can
be checked without dereferencing the group pointer of the latter struct.
The initial value for this flag is correctly set to 'false' when a
group is created, but we miss the case when no group is created at
all, in which case the initial value should be 'true'. This has the
effect that SOCK_RDM/DGRAM sockets sending datagrams never receive
POLLOUT if they request so.
This commit corrects this bug.
Fixes: 60c2530696 ("tipc: fix race between poll() and setsockopt()")
Reported-by: Hoang Le <hoang.h.le@dektek.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit cc1ea9ffadf7 ("tipc: eliminate struct tipc_subscriber") we
re-introduced an old bug on the error path in the function
tipc_topsrv_kern_subscr(). We now re-introduce the correction too.
Reported-by: syzbot+f62e0f2a0ef578703946@syzkaller.appspotmail.com
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We rename struct tipc_server to struct tipc_topsrv. This reflect its now
specialized role as topology server. Accoringly, we change or add function
prefixes to make it clearer which functionality those belong to.
There are no functional changes in this commit.
Acked-by: Ying.Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the listener socket to struct tipc_server and give it its own
work item. This makes it easier to follow the code, and entails some
simplifications in the reception code in subscriber sockets.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to narrow the interface and dependencies between the topology
server and the subscription/binding table functionality we move struct
tipc_server inside the file server.c. This requires some code
adaptations in other files, but those are mostly minor.
The most important change is that we have to move the start/stop
functions for the topology server to server.c, where they logically
belong anyway.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we now have removed struct tipc_subscriber from the code, and
only struct tipc_subscription remains, there is no longer need for long
and awkward prefixes to distinguish between their pertaining functions.
We now change all tipc_subscrp_* prefixes to tipc_sub_*. This is
a purely cosmetic change.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous changes it becomes logical to collapse the two-level
creation of subscription instances into one. We do that here.
We also rename the creation and deletion functions for more consistency.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of the requirement for total distribution transparency, users
send subscriptions and receive topology events in their own host format.
It is up to the topology server to determine this format and do the
correct conversions to and from its own host format when needed.
Until now, this has been handled in a rather non-transparent way inside
the topology server and subscriber code, leading to unnecessary
complexity when creating subscriptions and issuing events.
We now improve this situation by adding two new macros, tipc_sub_read()
and tipc_evt_write(). Both those functions calculate the need for
conversion internally before performing their respective operations.
Hence, all handling of such conversions become transparent to the rest
of the code.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message transmission and reception in the topology server is more
generic than is currently necessary. By basing the funtionality on the
fact that we only send items of type struct tipc_event and always
receive items of struct tipc_subcr we can make several simplifications,
and also get rid of some unnecessary dynamic memory allocations.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to keep two structures, struct tipc_conn and struct
tipc_subscriber, with a one-to-one relationship and still with different
life cycles. The fact that the two often run in different contexts, and
still may access each other via direct pointers constitutes an additional
hazard, something we have experienced at several occasions, and still
see happening.
We have identified at least two remaining problems that are easier to
fix if we simplify the topology server data structure somewhat.
- When there is a race between a subscription up/down event and a
timeout event, it is fully possible that the former might be delivered
after the latter, leading to confusion for the receiver.
- The function tipc_subcrp_timeout() is executing in interrupt context,
while the following call chain is at least theoretically possible:
tipc_subscrp_timeout()
tipc_subscrp_send_event()
tipc_conn_sendmsg()
conn_put()
tipc_conn_kref_release()
sock_release(sock)
I.e., we end up calling a function that might try to sleep in
interrupt context. To eliminate this, we need to ensure that the
tipc_conn structure and the socket, as well as the subscription
instances, only are deleted in work queue context, i.e., after the
timeout event really has been sent out.
We now remove this unnecessary complexity, by merging data and
functionality of the subscriber structure into struct tipc_conn
and the associated file server.c. We thereafter add a spinlock and
a new 'inactive' state to the subscription structure. Using those,
both problems described above can be easily solved.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interaction between the functionality in server.c and subscr.c is
done via function pointers installed in struct server. This makes
the code harder to follow, and doesn't serve any obvious purpose.
Here, we replace the function pointers with direct function calls.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket handling in the topology server is unnecessarily generic.
It is prepared to handle both SOCK_RDM, SOCK_DGRAM and SOCK_STREAM
type sockets, as well as the only socket type which is really used,
SOCK_SEQPACKET.
We now remove this redundant code to make the code more readable.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the default link tolerance set in struct tipc_bearer only
has effect on links going up after that moment. I.e., a user has to
reset all the node's links across that bearer to have the new value
applied. This is too limiting and disturbing on a running cluster to
be useful.
We now change this so that also already existing links are updated
dynamically, without any need for a reset, when the bearer value is
changed. We leverage the already existing per-link functionality
for this to achieve the wanted effect.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when user changes link properties, TIPC first checks if
user's command message contains media name or bearer name through
tipc_media_find() or tipc_bearer_find() which is protected by RTNL
lock. But when tipc_nl_compat_link_set() conducts the checking with
the two functions, it doesn't hold RTNL lock at all, as a result,
the following complaints were reported:
audit: type=1400 audit(1514679888.244:9): avc: denied { write } for
pid=3194 comm="syzkaller021477" path="socket:[11143]" dev="sockfs"
ino=11143 scontext=unconfined_u:system_r:insmod_t:s0-s0:c0.c1023
tcontext=unconfined_u:system_r:insmod_t:s0-s0:c0.c1023
tclass=netlink_generic_socket permissive=1
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
=============================
WARNING: suspicious RCU usage
4.15.0-rc5+ #152 Not tainted
-----------------------------
net/tipc/bearer.c:177 suspicious rcu_dereference_protected() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
2 locks held by syzkaller021477/3194:
#0: (cb_lock){++++}, at: [<00000000d20133ea>] genl_rcv+0x19/0x40
net/netlink/genetlink.c:634
#1: (genl_mutex){+.+.}, at: [<00000000fcc5d1bc>] genl_lock
net/netlink/genetlink.c:33 [inline]
#1: (genl_mutex){+.+.}, at: [<00000000fcc5d1bc>] genl_rcv_msg+0x115/0x140
net/netlink/genetlink.c:622
stack backtrace:
CPU: 1 PID: 3194 Comm: syzkaller021477 Not tainted 4.15.0-rc5+ #152
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:53
lockdep_rcu_suspicious+0x123/0x170 kernel/locking/lockdep.c:4585
tipc_bearer_find+0x2b4/0x3b0 net/tipc/bearer.c:177
tipc_nl_compat_link_set+0x329/0x9f0 net/tipc/netlink_compat.c:729
__tipc_nl_compat_doit net/tipc/netlink_compat.c:288 [inline]
tipc_nl_compat_doit+0x15b/0x660 net/tipc/netlink_compat.c:335
tipc_nl_compat_handle net/tipc/netlink_compat.c:1119 [inline]
tipc_nl_compat_recv+0x112f/0x18f0 net/tipc/netlink_compat.c:1201
genl_family_rcv_msg+0x7b7/0xfb0 net/netlink/genetlink.c:599
genl_rcv_msg+0xb2/0x140 net/netlink/genetlink.c:624
netlink_rcv_skb+0x21e/0x460 net/netlink/af_netlink.c:2408
genl_rcv+0x28/0x40 net/netlink/genetlink.c:635
netlink_unicast_kernel net/netlink/af_netlink.c:1275 [inline]
netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1301
netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1864
sock_sendmsg_nosec net/socket.c:636 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:646
sock_write_iter+0x31a/0x5d0 net/socket.c:915
call_write_iter include/linux/fs.h:1772 [inline]
new_sync_write fs/read_write.c:469 [inline]
__vfs_write+0x684/0x970 fs/read_write.c:482
vfs_write+0x189/0x510 fs/read_write.c:544
SYSC_write fs/read_write.c:589 [inline]
SyS_write+0xef/0x220 fs/read_write.c:581
do_syscall_32_irqs_on arch/x86/entry/common.c:327 [inline]
do_fast_syscall_32+0x3ee/0xf9d arch/x86/entry/common.c:389
entry_SYSENTER_compat+0x54/0x63 arch/x86/entry/entry_64_compat.S:129
In order to correct the mistake, __tipc_nl_compat_doit() has been
protected by RTNL lock, which means the whole operation of setting
bearer/media properties is under RTNL protection.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reported-by: syzbot <syzbot+6345fd433db009b29413@syzkaller.appspotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce __tipc_nl_net_set() which doesn't hold RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce __tipc_nl_media_set() which doesn't hold RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce __tipc_nl_bearer_set() which doesn't holding RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce __tipc_nl_bearer_enable() which doesn't hold RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce __tipc_nl_bearer_disable() which doesn't hold RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As preparation for adding RTNL to make (*cmd->transcode)() and
(*cmd->transcode)() constantly protected by RTNL lock, we move out of
memory allocations existing between them as many as possible so that
the time of holding RTNL can be minimized in __tipc_nl_compat_doit().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes since v1:
Added changes in these files:
drivers/infiniband/hw/usnic/usnic_transport.c
drivers/staging/lustre/lnet/lnet/lib-socket.c
drivers/target/iscsi/iscsi_target_login.c
drivers/vhost/net.c
fs/dlm/lowcomms.c
fs/ocfs2/cluster/tcp.c
security/tomoyo/network.c
Before:
All these functions either return a negative error indicator,
or store length of sockaddr into "int *socklen" parameter
and return zero on success.
"int *socklen" parameter is awkward. For example, if caller does not
care, it still needs to provide on-stack storage for the value
it does not need.
None of the many FOO_getname() functions of various protocols
ever used old value of *socklen. They always just overwrite it.
This change drops this parameter, and makes all these functions, on success,
return length of sockaddr. It's always >= 0 and can be differentiated
from an error.
Tests in callers are changed from "if (err)" to "if (err < 0)", where needed.
rpc_sockname() lost "int buflen" parameter, since its only use was
to be passed to kernel_getsockname() as &buflen and subsequently
not used in any way.
Userspace API is not changed.
text data bss dec hex filename
30108430 2633624 873672 33615726 200ef6e vmlinux.before.o
30108109 2633612 873672 33615393 200ee21 vmlinux.o
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-decnet-user@lists.sourceforge.net
CC: linux-wireless@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: linux-sctp@vger.kernel.org
CC: linux-nfs@vger.kernel.org
CC: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit d618d09a68 ("tipc: enforce valid ratio between skb truesize
and contents") we introduced a test for ensuring that the condition
truesize/datasize <= 4 is true for a received buffer. Unfortunately this
test has two problems.
- Because of the integer arithmetics the test
if (skb->truesize / buf_roundup_len(skb) > 4) will miss all
ratios [4 < ratio < 5], which was not the intention.
- The buffer returned by skb_copy() inherits skb->truesize of the
original buffer, which doesn't help the situation at all.
In this commit, we change the ratio condition and replace skb_copy()
with a call to skb_copy_expand() to finally get this right.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull kern_recvmsg reduction from Al Viro:
"kernel_recvmsg() is a set_fs()-using wrapper for sock_recvmsg(). In
all but one case that is not needed - use of ITER_KVEC for ->msg_iter
takes care of the data and does not care about set_fs(). The only
exception is svc_udp_recvfrom() where we want cmsg to be store into
kernel object; everything else can just use sock_recvmsg() and be done
with that.
A followup converting svc_udp_recvfrom() away from set_fs() (and
killing kernel_recvmsg() off) is *NOT* in here - I'd like to hear what
netdev folks think of the approach proposed in that followup)"
* 'work.sock_recvmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
tipc: switch to sock_recvmsg()
smc: switch to sock_recvmsg()
ipvs: switch to sock_recvmsg()
mISDN: switch to sock_recvmsg()
drbd: switch to sock_recvmsg()
lustre lnet_sock_read(): switch to sock_recvmsg()
cfs2: switch to sock_recvmsg()
ncpfs: switch to sock_recvmsg()
dlm: switch to sock_recvmsg()
svc_recvfrom(): switch to sock_recvmsg()
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Letting tipc_poll() dereference a socket's pointer to struct tipc_group
entails a race risk, as the group item may be deleted in a concurrent
tipc_sk_join() or tipc_sk_leave() thread.
We now move the 'open' flag in struct tipc_group to struct tipc_sock,
and let the former retain only a pointer to the moved field. This will
eliminate the race risk.
Reported-by: syzbot+799dafde0286795858ac@syzkaller.appspotmail.com
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have identified a race condition during reception of socket
events and messages in the topology server.
- The function tipc_close_conn() is releasing the corresponding
struct tipc_subscriber instance without considering that there
may still be items in the receive work queue. When those are
scheduled, in the function tipc_receive_from_work(), they are
using the subscriber pointer stored in struct tipc_conn, without
first checking if this is valid or not. This will sometimes
lead to crashes, as the next call of tipc_conn_recvmsg() will
access the now deleted item.
We fix this by making the usage of this pointer conditional on
whether the connection is active or not. I.e., we check the condition
test_bit(CF_CONNECTED) before making the call tipc_conn_recvmsg().
- Since the two functions may be running on different cores, the
condition test described above is not enough. tipc_close_conn()
may come in between and delete the subscriber item after the condition
test is done, but before tipc_conn_recv_msg() is finished. This
happens less frequently than the problem described above, but leads
to the same symptoms.
We fix this by using the existing sk_callback_lock for mutual
exclusion in the two functions. In addition, we have to move
a call to tipc_conn_terminate() outside the mentioned lock to
avoid deadlock.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 232d07b74a ("tipc: improve groupcast scope handling") we
inadvertently broke non-group multicast transmission when changing the
parameter 'domain' to 'scope' in the function
tipc_nametbl_lookup_dst_nodes(). We missed to make the corresponding
change in the calling function, with the result that the lookup always
fails.
A closer anaysis reveals that this parameter is not needed at all.
Non-group multicast is hard coded to use CLUSTER_SCOPE, and in the
current implementation this will be delivered to all matching
destinations except those which are published with NODE_SCOPE on other
nodes. Since such publications never will be visible on the sending node
anyway, it makes no sense to discriminate by scope at all.
We now remove this parameter altogether.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc_node_find_by_name() fails, the nlmsg is not
freed.
While on it, switch to a goto label to properly
free it.
Fixes: be9c086715c ("tipc: narrow down exposure of struct tipc_node")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit d12d2e12ce "tipc: send out join messages as soon as new
member is discovered") we added a call to the function tipc_group_join()
without considering the case that the preceding tipc_sk_publish() might
have failed, and the group item already deleted.
We fix this by returning from tipc_sk_join() directly after the
failed tipc_sk_publish.
Reported-by: syzbot+e3eeae78ea88b8d6d858@syzkaller.appspotmail.com
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current criteria for returning POLLOUT from a group member socket is
too simplistic. It basically returns POLLOUT as soon as the group has
external destinations, something obviously leading to a lot of spinning
during destination congestion situations. At the same time, the internal
congestion handling is unnecessarily complex.
We now change this as follows.
- We introduce an 'open' flag in struct tipc_group. This flag is used
only to help poll() get the setting of POLLOUT right, and *not* for
congeston handling as such. This means that a user can choose to
ignore an EAGAIN for a destination and go on sending messages to
other destinations in the group if he wants to.
- The flag is set to false every time we return EAGAIN on a send call.
- The flag is set to true every time any member, i.e., not necessarily
the member that caused EAGAIN, is removed from the small_win list.
- We remove the group member 'usr_pending' flag. The size of the send
window and presence in the 'small_win' list is sufficient criteria
for recognizing congestion.
This solution seems to be a reasonable compromise between 'anycast',
which is normally not waiting for POLLOUT for a specific destination,
and the other three send modes, which are.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a member joins a group, it also indicates a binding scope. This
makes it possible to create both node local groups, invisible to other
nodes, as well as cluster global groups, visible everywhere.
In order to avoid that different members end up having permanently
differing views of group size and memberhip, we must inhibit locally
and globally bound members from joining the same group.
We do this by using the binding scope as an additional separator between
groups. I.e., a member must ignore all membership events from sockets
using a different scope than itself, and all lookups for message
destinations must require an exact match between the message's lookup
scope and the potential target's binding scope.
Apart from making it possible to create local groups using the same
identity on different nodes, a side effect of this is that it now also
becomes possible to create a cluster global group with the same identity
across the same nodes, without interfering with the local groups.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when a user is subscribing for binding table publications,
he will receive a PUBLISH event for all already existing matching items
in the binding table.
However, a group socket making a subscriptions doesn't need this initial
status update from the binding table, because it has already scanned it
during the join operation. Worse, the multiplicatory effect of issuing
mutual events for dozens or hundreds group members within a short time
frame put a heavy load on the topology server, with the end result that
scale out operations on a big group tend to take much longer than needed.
We now add a new filter option, TIPC_SUB_NO_STATUS, for topology server
subscriptions, so that this initial avalanche of events is suppressed.
This change, along with the previous commit, significantly improves the
range and speed of group scale out operations.
We keep the new option internal for the tipc driver, at least for now.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a socket is joining a group, we look up in the binding table to
find if there are already other members of the group present. This is
used for being able to return EAGAIN instead of EHOSTUNREACH if the
user proceeds directly to a send attempt.
However, the information in the binding table can be used to directly
set the created member in state MBR_PUBLISHED and send a JOIN message
to the peer, instead of waiting for a topology PUBLISH event to do this.
When there are many members in a group, the propagation time for such
events can be significant, and we can save time during the join
operation if we use the initial lookup result fully.
In this commit, we eliminate the member state MBR_DISCOVERED which has
been the result of the initial lookup, and do instead go directly to
MBR_PUBLISHED, which initiates the setup.
After this change, the tipc_member FSM looks as follows:
+-----------+
---->| PUBLISHED |-----------------------------------------------+
PUB- +-----------+ LEAVE/WITHRAW |
LISH |JOIN |
| +-------------------------------------------+ |
| | LEAVE/WITHDRAW | |
| | +------------+ | |
| | +----------->| PENDING |---------+ | |
| | |msg/maxactv +-+---+------+ LEAVE/ | | |
| | | | | WITHDRAW | | |
| | | +----------+ | | | |
| | | |revert/maxactv| | | |
| | | V V V V V
| +----------+ msg +------------+ +-----------+
+-->| JOINED |------>| ACTIVE |------>| LEAVING |--->
| +----------+ +--- -+------+ LEAVE/+-----------+DOWN
| A A | WITHDRAW A A A EVT
| | | |RECLAIM | | |
| | |REMIT V | | |
| | |== adv +------------+ | | |
| | +---------| RECLAIMING |--------+ | |
| | +-----+------+ LEAVE/ | |
| | |REMIT WITHDRAW | |
| | |< adv | |
| |msg/ V LEAVE/ | |
| |adv==ADV_IDLE+------------+ WITHDRAW | |
| +-------------| REMITTED |------------+ |
| +------------+ |
|PUBLISH |
JOIN +-----------+ LEAVE/WITHDRAW |
---->| JOINING |-----------------------------------------------+
+-----------+
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the changes in the previous commit the group LEAVE sequence
can be simplified.
We now let the arrival of a LEAVE message unconditionally issue a group
DOWN event to the user. When a topology WITHDRAW event is received, the
member, if it still there, is set to state LEAVING, but we only issue a
group DOWN event when the link to the peer node is gone, so that no
LEAVE message is to be expected.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation, a group socket receiving topology
events about other members just converts the topology event message
into a group event message and stores it until it reaches the right
state to issue it to the user. This complicates the code unnecessarily,
and becomes impractical when we in the coming commits will need to
create and issue membership events independently.
In this commit, we change this so that we just notice the type and
origin of the incoming topology event, and then drop the buffer. Only
when it is time to actually send a group event to the user do we
explicitly create a new message and send it upwards.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Analysis reveals that the member state MBR_QURANTINED in reality is
unnecessary, and can be replaced by the state MBR_JOINING at all
occurrencs.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We handle a corner case in the function tipc_group_update_rcv_win().
During extreme pessure it might happen that a message receiver has all
its active senders in RECLAIMING or REMITTED mode, meaning that there
is nobody to reclaim advertisements from if an additional sender tries
to go active.
Currently we just set the new sender to ACTIVE anyway, hence at least
theoretically opening up for a receiver queue overflow by exceeding the
MAX_ACTIVE limit. The correct solution to this is to instead add the
member to the pending queue, while letting the oldest member in that
queue revert to JOINED state.
In this commit we refactor the code for handling message arrival from
a JOINED member, both to make it more comprehensible and to cover the
case described above.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- We remove the 'reclaiming' member list in struct tipc_group, since
it doesn't serve any purpose.
- We simplify the GRP_REMIT_MSG branch of tipc_group_protocol_rcv().
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preempt counter APIs have been split out, currently, hardirq.h just
includes irq_enter/exit APIs which are not used by TIPC at all.
So, remove the unused hardirq.h.
Signed-off-by: Yang Shi <yang.s@alibaba-inc.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simplify the sorting algorithm in tipc_update_member(). We also make
the remaining conditional call to this function unconditional, since the
same condition now is tested for inside the said function.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We rename some functions and variables, to make their purpose clearer.
- tipc_group::congested -> tipc_group::small_win. Members in this list
are not necessarily (and typically) congested. Instead, they may
*potentially* be subject to congestion because their send window is
less than ADV_IDLE, and therefore need to be checked during message
transmission.
- tipc_group_is_receiver() -> tipc_group_is_sender(). This socket will
accept messages coming from members fulfilling this condition, i.e.,
they are senders from this member's viewpoint.
- tipc_group_is_enabled() -> tipc_group_is_receiver(). Members
fulfilling this condition will accept messages sent from the current
socket, i.e., they are receivers from its viewpoint.
There are no functional changes in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 04d7b574b2 ("tipc: add multipoint-to-point flow control") we
introduced a protocol for preventing buffer overflow when many group
members try to simultaneously send messages to the same receiving member.
Stress test of this mechanism has revealed a couple of related bugs:
- When the receiving member receives an advertisement REMIT message from
one of the senders, it will sometimes prematurely activate a pending
member and send it the remitted advertisement, although the upper
limit for active senders has been reached. This leads to accumulation
of illegal advertisements, and eventually to messages being dropped
because of receive buffer overflow.
- When the receiving member leaves REMITTED state while a received
message is being read, we miss to look at the pending queue, to
activate the oldest pending peer. This leads to some pending senders
being starved out, and never getting the opportunity to profit from
the remitted advertisement.
We fix the former in the function tipc_group_proto_rcv() by returning
directly from the function once it becomes clear that the remitting
peer cannot leave REMITTED state at that point.
We fix the latter in the function tipc_group_update_rcv_win() by looking
up and activate the longest pending peer when it becomes clear that the
remitting peer now can leave REMITTED state.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 42b531de17 ("tipc: Fix missing connection request
handling"), we replaced unconditional wakeup() with condtional
wakeup for clients with flags POLLIN | POLLRDNORM | POLLRDBAND.
This breaks the applications which do a connect followed by poll
with POLLOUT flag. These applications are not woken when the
connection is ESTABLISHED and hence sleep forever.
In this commit, we fix it by including the POLLOUT event for
sockets in TIPC_CONNECTING state.
Fixes: 42b531de17 ("tipc: Fix missing connection request handling")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory leak in tipc_enable_bearer() if enable_media() fails, and
cleanup with bearer_disable() if tipc_mon_create() fails.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a group member receives a member WITHDRAW event, this might have
two reasons: either the peer member is leaving the group, or the link
to the member's node has been lost.
In the latter case we need to issue a DOWN event to the user right away,
and let function tipc_group_filter_msg() perform delete of the member
item. However, in this case we miss to change the state of the member
item to MBR_LEAVING, so the member item is not deleted, and we have a
memory leak.
We now separate better between the four sub-cases of a WITHRAW event
and make sure that each case is handled correctly.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 2f487712b8 ("tipc: guarantee that group broadcast doesn't
bypass group unicast") we introduced a mechanism that requires the first
(replicated) broadcast sent after a unicast to be acknowledged by all
receivers before permitting sending of the next (true) broadcast.
The counter for keeping track of the number of acknowledges to expect
is based on the tipc_group::member_cnt variable. But this misses that
some of the known members may not be ready for reception, and will never
acknowledge the message, either because they haven't fully joined the
group or because they are leaving the group. Such members are identified
by not fulfilling the condition tested for in the function
tipc_group_is_enabled().
We now set the counter for the actual number of acks to receive at the
moment the message is sent, by just counting the number of recipients
satisfying the tipc_group_is_enabled() test.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When we receive a JOIN message from a peer member, the message may
contain an advertised window value ADV_IDLE that permits removing the
member in question from the tipc_group::congested list. However, since
the removal has been made conditional on that the advertised window is
*not* ADV_IDLE, we miss this case. This has the effect that a sender
sometimes may enter a state of permanent, false, broadcast congestion.
We fix this by unconditinally removing the member from the congested
list before calling tipc_member_update(), which might potentially sort
it into the list again.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When, during a join operation, or during message transmission, a group
member needs to be added to the group's 'congested' list, we sort it
into the list in ascending order, according to its current advertised
window size. However, we miss the case when the member is already on
that list. This will have the result that the member, after the window
size has been decremented, might be at the wrong position in that list.
This again may have the effect that we during broadcast and multicast
transmissions miss the fact that a destination is not yet ready for
reception, and we end up sending anyway. From this point on, the
behavior during the remaining session is unpredictable, e.g., with
underflowing window sizes.
We now correct this bug by unconditionally removing the member from
the list before (re-)sorting it in.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A group member going into state LEAVING should never go back to any
other state before it is finally deleted. However, this might happen
if the socket needs to send out a RECLAIM message during this interval.
Since we forget to remove the leaving member from the group's 'active'
or 'pending' list, the member might be selected for reclaiming, change
state to RECLAIMING, and get stuck in this state instead of being
deleted. This might lead to suppression of the expected 'member down'
event to the receiver.
We fix this by removing the member from all lists, except the RB tree,
at the moment it goes into state LEAVING.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group messages are not supposed to be returned to sender when the
destination socket disappears. This is done correctly for regular
traffic messages, by setting the 'dest_droppable' bit in the header.
But we forget to do that in group protocol messages. This has the effect
that such messages may sometimes bounce back to the sender, be perceived
as a legitimate peer message, and wreak general havoc for the rest of
the session. In particular, we have seen that a member in state LEAVING
may go back to state RECLAIMED or REMITTED, hence causing suppression
of an otherwise expected 'member down' event to the user.
We fix this by setting the 'dest_droppable' bit even in group protocol
messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function tipc_sk_mcast_rcv() we call refcount_dec(&skb->users)
on received sk_buffers. Since the reference counter might hit zero at
this point, we have a potential memory leak.
We fix this by replacing refcount_dec() with kfree_skb().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the function tipc_accept_from_sock() fails to create an instance of
struct tipc_subscriber it omits to free the already created instance of
struct tipc_conn instance before it returns.
We fix that with this commit.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small overlapping change conflict ('net' changed a line,
'net-next' added a line right afterwards) in flexcan.c
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending node local messages the code is using an 'mtu' of 66060
bytes to avoid unnecessary fragmentation. During situations of low
memory tipc_msg_build() may sometimes fail to allocate such large
buffers, resulting in unnecessary send failures. This can easily be
remedied by falling back to a smaller MTU, and then reassemble the
buffer chain as if the message were arriving from a remote node.
At the same time, we change the initial MTU setting of the broadcast
link to a lower value, so that large messages always are fragmented
into smaller buffers even when we run in single node mode. Apart from
obtaining the same advantage as for the 'fallback' solution above, this
turns out to give a significant performance improvement. This can
probably be explained with the __pskb_copy() operation performed on the
buffer for each recipient during reception. We found the optimal value
for this, considering the most relevant skb pool, to be 3744 bytes.
Acked-by: Ying Xue <ying.xue@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KASAN revealed another access after delete in group.c. This time
it found that we read the header of a received message after the
buffer has been released.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the function tipc_group_filter_msg() finds that a member event
indicates that the member is leaving the group, it first deletes the
member instance, and then purges the message queue being handled
by the call. But the message queue is an aggregated field in the
just deleted item, leading the purge call to access freed memory.
We fix this by swapping the order of the two actions.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket level flow control is based on the assumption that incoming
buffers meet the condition (skb->truesize / roundup(skb->len) <= 4),
where the latter value is rounded off upwards to the nearest 1k number.
This does empirically hold true for the device drivers we know, but we
cannot trust that it will always be so, e.g., in a system with jumbo
frames and very small packets.
We now introduce a check for this condition at packet arrival, and if
we find it to be false, we copy the packet to a new, smaller buffer,
where the condition will be true. We expect this to affect only a small
fraction of all incoming packets, if at all.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the TIPC RPS dissector is based only on the incoming packets'
source node address, hence steering all traffic from a node to the same
core. We have seen that this makes the links vulnerable to starvation
and unnecessary resets when we turn down the link tolerance to very low
values.
To reduce the risk of this happening, we exempt probe and probe replies
packets from the convergence to one core per source node. Instead, we do
the opposite, - we try to diverge those packets across as many cores as
possible, by randomizing the flow selector key.
To make such packets identifiable to the dissector, we add a new
'is_keepalive' bit to word 0 of the LINK_PROTOCOL header. This bit is
set both for PROBE and PROBE_REPLY messages, and only for those.
It should be noted that these packets are not part of any flow anyway,
and only constitute a minuscule fraction of all packets sent across a
link. Hence, there is no risk that this will affect overall performance.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The neighbor monitor employs a threshold, default set to 32 peer nodes,
where it activates the "Overlapping Neighbor Monitoring" algorithm.
Below that threshold, monitoring is full-mesh, and no "domain records"
are passed between the nodes.
Because of this, a node never received a peer's ack that it has received
the most recent update of the own domain. Hence, the field 'acked_gen'
in struct tipc_monitor_state remains permamently at zero, whereas the
own domain generation is incremented for each added or removed peer.
This has the effect that the function tipc_mon_get_state() always sets
the field 'probing' in struct tipc_monitor_state true, again leading the
tipc_link_timeout() of the link in question to always send out a probe,
even when link->silent_intv_count is zero.
This is functionally harmless, but leads to some unncessary probing,
which can easily be eliminated by setting the 'probing' field of the
said struct correctly in such cases.
At the same time, we explictly invalidate the sent domain records when
the algorithm is not activated. This will eliminate any risk that an
invalid domain record might be inadverently accepted by the peer.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: tipc-discussion@lists.sourceforge.net
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tsk->group is set to grp earlier, but we forget to unset it
after grp is freed.
Fixes: 75da2163db ("tipc: introduce communication groups")
Reported-by: syzkaller bot
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following warning was reported by syzbot on Oct 24. 2017:
KASAN: slab-out-of-bounds Read in tipc_nametbl_lookup_dst_nodes
This is a harmless bug, but we still want to get rid of the warning,
so we swap the two conditions in question.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_sk_timeout() is more complex than necessary, and
even seems to contain an undetected bug. At one of the occurences
where we renew the timer we just order it with (HZ / 20), instead
of (jiffies + HZ / 20);
In this commit we clean up the function.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit ae236fb208 ("tipc: receive group membership events via
member socket") we broke the tipc_poll() function by checking the
state of the receive queue before the call to poll_sock_wait(), while
relying that state afterwards, when it might have changed.
We restore this in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tipc_alloc_conn() function never returns NULL, it returns error
pointers, so I have fixed the check.
Fixes: 14c04493cb ("tipc: add ability to order and receive topology events in driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 2f487712b8 ("tipc: guarantee that group broadcast doesn't
bypass group unicast") there was introduced a last-minute rebasing
error that broke non-group communication.
We fix this here.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have point-to-multipoint flow control within a group. But
we even need the opposite; -a scheme which can handle that potentially
hundreds of sources may try to send messages to the same destination
simultaneously without causing buffer overflow at the recipient. This
commit adds such a mechanism.
The algorithm works as follows:
- When a member detects a new, joining member, it initially set its
state to JOINED and advertises a minimum window to the new member.
This window is chosen so that the new member can send exactly one
maximum sized message, or several smaller ones, to the recipient
before it must stop and wait for an additional advertisement. This
minimum window ADV_IDLE is set to 65 1kB blocks.
- When a member receives the first data message from a JOINED member,
it changes the state of the latter to ACTIVE, and advertises a larger
window ADV_ACTIVE = 12 x ADV_IDLE blocks to the sender, so it can
continue sending with minimal disturbances to the data flow.
- The active members are kept in a dedicated linked list. Each time a
message is received from an active member, it will be moved to the
tail of that list. This way, we keep a record of which members have
been most (tail) and least (head) recently active.
- There is a maximum number (16) of permitted simultaneous active
senders per receiver. When this limit is reached, the receiver will
not advertise anything immediately to a new sender, but instead put
it in a PENDING state, and add it to a corresponding queue. At the
same time, it will pick the least recently active member, send it an
advertisement RECLAIM message, and set this member to state
RECLAIMING.
- The reclaimee member has to respond with a REMIT message, meaning that
it goes back to a send window of ADV_IDLE, and returns its unused
advertised blocks beyond that value to the reclaiming member.
- When the reclaiming member receives the REMIT message, it unlinks
the reclaimee from its active list, resets its state to JOINED, and
notes that it is now back at ADV_IDLE advertised blocks to that
member. If there are still unread data messages sent out by
reclaimee before the REMIT, the member goes into an intermediate
state REMITTED, where it stays until the said messages have been
consumed.
- The returned advertised blocks can now be re-advertised to the
pending member, which is now set to state ACTIVE and added to
the active member list.
- To be proactive, i.e., to minimize the risk that any member will
end up in the pending queue, we start reclaiming resources already
when the number of active members exceeds 3/4 of the permitted
maximum.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following scenario is possible:
- A user sends a broadcast message, and thereafter immediately leaves
the group.
- The LEAVE message, following a different path than the broadcast,
arrives ahead of the broadcast, and the sending member is removed
from the receiver's list.
- The broadcast message arrives, but is dropped because the sender
now is unknown to the receipient.
We fix this by sequence numbering membership events, just like ordinary
unicast messages. Currently, when a JOIN is sent to a peer, it contains
a synchronization point, - the sequence number of the next sent
broadcast, in order to give the receiver a start synchronization point.
We now let even LEAVE messages contain such an "end synchronization"
point, so that the recipient can delay the removal of the sending member
until it knows that all messages have been received.
The received synchronization points are added as sequence numbers to the
generated membership events, making it possible to handle them almost
the same way as regular unicasts in the receiving filter function. In
particular, a DOWN event with a too high sequence number will be kept
in the reordering queue until the missing broadcast(s) arrive and have
been delivered.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following scenario is possible:
- A user joins a group, and immediately sends out a broadcast message
to its members.
- The broadcast message, following a different data path than the
initial JOIN message sent out during the joining procedure, arrives
to a receiver before the latter..
- The receiver drops the message, since it is not ready to accept any
messages until the JOIN has arrived.
We avoid this by treating group protocol JOIN messages like unicast
messages.
- We let them pass through the recipient's multicast input queue, just
like ordinary unicasts.
- We force the first following broadacst to be sent as replicated
unicast and being acknowledged by the recipient before accepting
any more broadcast transmissions.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a mechanism guaranteeing that group unicasts sent out from a
socket are not bypassed by later sent broadcasts from the same socket.
We do this as follows:
- Each time a unicast is sent, we set a the broadcast method for the
socket to "replicast" and "mandatory". This forces the first
subsequent broadcast message to follow the same network and data path
as the preceding unicast to a destination, hence preventing it from
overtaking the latter.
- In order to make the 'same data path' statement above true, we let
group unicasts pass through the multicast link input queue, instead
of as previously through the unicast link input queue.
- In the first broadcast following a unicast, we set a new header flag,
requiring all recipients to immediately acknowledge its reception.
- During the period before all the expected acknowledges are received,
the socket refuses to accept any more broadcast attempts, i.e., by
blocking or returning EAGAIN. This period should typically not be
longer than a few microseconds.
- When all acknowledges have been received, the sending socket will
open up for subsequent broadcasts, this time giving the link layer
freedom to itself select the best transmission method.
- The forced and/or abrupt transmission method changes described above
may lead to broadcasts arriving out of order to the recipients. We
remedy this by introducing code that checks and if necessary
re-orders such messages at the receiving end.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group unicast messages don't follow the same path as broadcast messages,
and there is a high risk that unicasts sent from a socket might bypass
previously sent broadcasts from the same socket.
We fix this by letting all unicast messages carry the sequence number of
the next sent broadcast from the same node, but without updating this
number at the receiver. This way, a receiver can check and if necessary
re-order such messages before they are added to the socket receive buffer.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previously introduced message transport to all group members is
based on the tipc multicast service, but is logically a broadcast
service within the group, and that is what we call it.
We now add functionality for sending messages to all group members
having a certain identity. Correspondingly, we call this feature 'group
multicast'. The service is using unicast when only one destination is
found, otherwise it will use the bearer broadcast service to transfer
the messages. In the latter case, the receiving members filter arriving
messages by looking at the intended destination instance. If there is
no match, the message will be dropped, while still being considered
received and read as seen by the flow control mechanism.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit, we make it possible to send connectionless unicast
messages to any member corresponding to the given member identity,
when there is more than one such member. The sender must use a
TIPC_ADDR_NAME address to achieve this effect.
We also perform load balancing between the destinations, i.e., we
primarily select one which has advertised sufficient send window
to not cause a block/EAGAIN delay, if any. This mechanism is
overlayed on the always present round-robin selection.
Anycast messages are subject to the same start synchronization
and flow control mechanism as group broadcast messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now make it possible to send connectionless unicast messages
within a communication group. To send a message, the sender can use
either a direct port address, aka port identity, or an indirect port
name to be looked up.
This type of messages are subject to the same start synchronization
and flow control mechanism as group broadcast messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduce an end-to-end flow control mechanism for group broadcast
messages. This ensures that no messages are ever lost because of
destination receive buffer overflow, with minimal impact on performance.
For now, the algorithm is based on the assumption that there is only one
active transmitter at any moment in time.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like with any other service, group members' availability can be
subscribed for by connecting to be topology server. However, because
the events arrive via a different socket than the member socket, there
is a real risk that membership events my arrive out of synch with the
actual JOIN/LEAVE action. I.e., it is possible to receive the first
messages from a new member before the corresponding JOIN event arrives,
just as it is possible to receive the last messages from a leaving
member after the LEAVE event has already been received.
Since each member socket is internally also subscribing for membership
events, we now fix this problem by passing those events on to the user
via the member socket. We leverage the already present member synch-
ronization protocol to guarantee correct message/event order. An event
is delivered to the user as an empty message where the two source
addresses identify the new/lost member. Furthermore, we set the MSG_OOB
bit in the message flags to mark it as an event. If the event is an
indication about a member loss we also set the MSG_EOR bit, so it can
be distinguished from a member addition event.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With group communication, it becomes important for a message receiver to
identify not only from which socket (identfied by a node:port tuple) the
message was sent, but also the logical identity (type:instance) of the
sending member.
We fix this by adding a second instance of struct sockaddr_tipc to the
source address area when a message is read. The extra address struct
is filled in with data found in the received message header (type,) and
in the local member representation struct (instance.)
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for introducing flow control for multicast and datagram
messaging we need a more strictly defined framework than we have now. A
socket must be able keep track of exactly how many and which other
sockets it is allowed to communicate with at any moment, and keep the
necessary state for those.
We therefore introduce a new concept we have named Communication Group.
Sockets can join a group via a new setsockopt() call TIPC_GROUP_JOIN.
The call takes four parameters: 'type' serves as group identifier,
'instance' serves as an logical member identifier, and 'scope' indicates
the visibility of the group (node/cluster/zone). Finally, 'flags' makes
it possible to set certain properties for the member. For now, there is
only one flag, indicating if the creator of the socket wants to receive
a copy of broadcast or multicast messages it is sending via the socket,
and if wants to be eligible as destination for its own anycasts.
A group is closed, i.e., sockets which have not joined a group will
not be able to send messages to or receive messages from members of
the group, and vice versa.
Any member of a group can send multicast ('group broadcast') messages
to all group members, optionally including itself, using the primitive
send(). The messages are received via the recvmsg() primitive. A socket
can only be member of one group at a time.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We often see a need for a linked list of destination identities,
sometimes containing a port number, sometimes a node identity, and
sometimes both. The currently defined struct u32_list is not generic
enough to cover all cases, so we extend it to contain two u32 integers
and rename it to struct tipc_dest_list.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We see an increasing need to send multiple single-buffer messages
of TIPC_SYSTEM_IMPORTANCE to different individual destination nodes.
Instead of looping over the send queue and sending each buffer
individually, as we do now, we add a new help function
tipc_node_distr_xmit() to do this.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the following commits we will need to handle multiple incoming and
rejected/returned buffers in the function socket.c::filter_rcv().
As a preparation for this, we generalize the function by handling
buffer queues instead of individual buffers. We also introduce a
help function tipc_skb_reject(), and rename filter_rcv() to
tipc_sk_filter_rcv() in line with other functions in socket.c.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the coming commits, functions at the socket level will need the
ability to read the availability status of a given node. We therefore
introduce a new function for this purpose, while renaming the existing
static function currently having the wanted name.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address given to tipc_connect() is not completely sanity checked,
under the assumption that this will be done later in the function
__tipc_sendmsg() when the address is used there.
However, the latter functon will in the next commits serve as caller
to several other send functions, so we want to move the corresponding
sanity check there to the beginning of that function, before we possibly
need to grab the address stored by tipc_connect(). We must therefore
be able to trust that this address already has been thoroughly checked.
We do this in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As preparation for introducing communication groups, we add the ability
to issue topology subscriptions and receive topology events from kernel
space. This will make it possible for group member sockets to keep track
of other group members.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bundling message is received, the function tipc_link_input()
calls function tipc_msg_extract() to unbundle all inner messages of
the bundling message before adding them to input queue.
The function tipc_msg_extract() just clones all inner skb for all
inner messagges from the bundling skb. This means that the skb
headroom of an inner message overlaps with the data part of the
preceding message in the bundle.
If the message in question is a name addressed message, it may be
subject to a secondary destination lookup, and eventually be sent out
on one of the interfaces again. But, since what is perceived as headroom
by the device driver in reality is the last bytes of the preceding
message in the bundle, the latter will be overwritten by the MAC
addresses of the L2 header. If the preceding message has not yet been
consumed by the user, it will evenually be delivered with corrupted
contents.
This commit fixes this by uncloning all messages passing through the
function tipc_msg_lookup_dest(), hence ensuring that the headroom
is always valid when the message is passed on.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We change the initialization of the skb transmit buffer queues
in the functions tipc_bcast_xmit() and tipc_rcast_xmit() to also
initialize their spinlocks. This is needed because we may, during
error conditions, need to call skb_queue_purge() on those queues
further down the stack.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit e3a77561e7 ("tipc: split up function tipc_msg_eval()"),
we have updated the function tipc_msg_lookup_dest() to set the error
codes to negative values at destination lookup failures. Thus when
the function sets the error code to -TIPC_ERR_NO_NAME, its inserted
into the 4 bit error field of the message header as 0xf instead of
TIPC_ERR_NO_NAME (1). The value 0xf is an unknown error code.
In this commit, we set only positive error code.
Fixes: e3a77561e7 ("tipc: split up function tipc_msg_eval()")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net device is already stored in the 'net' variable, so no need to call
dev_net() again.
Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a bond slave device as a tipc bearer, the dev represents the bond
interface and orig_dev represents the slave in tipc_l2_rcv_msg().
Since we decode the tipc_ptr from bonding device (dev), we fail to
find the bearer and thus tipc links are not established.
In this commit, we register the tipc protocol callback per device and
look for tipc bearer from both the devices.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to find a valid bearer in tipc_node_get_linkname(),
node_read_unlock() is called without holding the node read lock.
This commit fixes this error.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_msg_reverse(), we assign skb attributes to local pointers
in stack at startup. This is followed by skb_linearize() and for
cloned buffers we perform skb relocation using pskb_expand_head().
Both these methods may update the skb attributes and thus making
the pointers incorrect.
In this commit, we fix this error by ensuring that the pointers
are re-assigned after any of these skb operations.
Fixes: 29042e19f2 ("tipc: let function tipc_msg_reverse() expand header
when needed")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_rcv(), we linearize only the header and usually the packets
are consumed as the nodes permit direct reception. However, if the
skb contains tunnelled message due to fail over or synchronization
we parse it in tipc_node_check_state() without performing
linearization. This will cause link disturbances if the skb was
non linear.
In this commit, we perform linearization for the above messages.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 9dbbfb0ab6 function tipc_sk_reinit
had additional logic added to loop in the event that function
rhashtable_walk_next() returned -EAGAIN. No worries.
However, if rhashtable_walk_start returns -EAGAIN, it does "continue",
and therefore skips the call to rhashtable_walk_stop(). That has
the effect of calling rcu_read_lock() without its paired call to
rcu_read_unlock(). Since rcu_read_lock() may be nested, the problem
may not be apparent for a while, especially since resize events may
be rare. But the comments to rhashtable_walk_start() state:
* ...Note that we take the RCU lock in all
* cases including when we return an error. So you must always call
* rhashtable_walk_stop to clean up.
This patch replaces the continue with a goto and label to ensure a
matching call to rhashtable_walk_stop().
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
genl_ops are not supposed to change at runtime. All functions
working with genl_ops provided by <net/genetlink.h> work with
const genl_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No matter whether a request is inserted into workqueue as a work item
to cancel a subscription or to delete a subscription's subscriber
asynchronously, the work items may be executed in different workers.
As a result, it doesn't mean that one request which is raised prior to
another request is definitely handled before the latter. By contrast,
if the latter request is executed before the former request, below
error may happen:
[ 656.183644] BUG: spinlock bad magic on CPU#0, kworker/u8:0/12117
[ 656.184487] general protection fault: 0000 [#1] SMP
[ 656.185160] Modules linked in: tipc ip6_udp_tunnel udp_tunnel 9pnet_virtio 9p 9pnet virtio_net virtio_pci virtio_ring virtio [last unloaded: ip6_udp_tunnel]
[ 656.187003] CPU: 0 PID: 12117 Comm: kworker/u8:0 Not tainted 4.11.0-rc7+ #6
[ 656.187920] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 656.188690] Workqueue: tipc_rcv tipc_recv_work [tipc]
[ 656.189371] task: ffff88003f5cec40 task.stack: ffffc90004448000
[ 656.190157] RIP: 0010:spin_bug+0xdd/0xf0
[ 656.190678] RSP: 0018:ffffc9000444bcb8 EFLAGS: 00010202
[ 656.191375] RAX: 0000000000000034 RBX: ffff88003f8d1388 RCX: 0000000000000000
[ 656.192321] RDX: ffff88003ba13708 RSI: ffff88003ba0cd08 RDI: ffff88003ba0cd08
[ 656.193265] RBP: ffffc9000444bcd0 R08: 0000000000000030 R09: 000000006b6b6b6b
[ 656.194208] R10: ffff8800bde3e000 R11: 00000000000001b4 R12: 6b6b6b6b6b6b6b6b
[ 656.195157] R13: ffffffff81a3ca64 R14: ffff88003f8d1388 R15: ffff88003f8d13a0
[ 656.196101] FS: 0000000000000000(0000) GS:ffff88003ba00000(0000) knlGS:0000000000000000
[ 656.197172] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 656.197935] CR2: 00007f0b3d2e6000 CR3: 000000003ef9e000 CR4: 00000000000006f0
[ 656.198873] Call Trace:
[ 656.199210] do_raw_spin_lock+0x66/0xa0
[ 656.199735] _raw_spin_lock_bh+0x19/0x20
[ 656.200258] tipc_subscrb_subscrp_delete+0x28/0xf0 [tipc]
[ 656.200990] tipc_subscrb_rcv_cb+0x45/0x260 [tipc]
[ 656.201632] tipc_receive_from_sock+0xaf/0x100 [tipc]
[ 656.202299] tipc_recv_work+0x2b/0x60 [tipc]
[ 656.202872] process_one_work+0x157/0x420
[ 656.203404] worker_thread+0x69/0x4c0
[ 656.203898] kthread+0x138/0x170
[ 656.204328] ? process_one_work+0x420/0x420
[ 656.204889] ? kthread_create_on_node+0x40/0x40
[ 656.205527] ret_from_fork+0x29/0x40
[ 656.206012] Code: 48 8b 0c 25 00 c5 00 00 48 c7 c7 f0 24 a3 81 48 81 c1 f0 05 00 00 65 8b 15 61 ef f5 7e e8 9a 4c 09 00 4d 85 e4 44 8b 4b 08 74 92 <45> 8b 84 24 40 04 00 00 49 8d 8c 24 f0 05 00 00 eb 8d 90 0f 1f
[ 656.208504] RIP: spin_bug+0xdd/0xf0 RSP: ffffc9000444bcb8
[ 656.209798] ---[ end trace e2a800e6eb0770be ]---
In above scenario, the request of deleting subscriber was performed
earlier than the request of canceling a subscription although the
latter was issued before the former, which means tipc_subscrb_delete()
was called before tipc_subscrp_cancel(). As a result, when
tipc_subscrb_subscrp_delete() called by tipc_subscrp_cancel() was
executed to cancel a subscription, the subscription's subscriber
refcnt had been decreased to 1. After tipc_subscrp_delete() where
the subscriber was freed because its refcnt was decremented to zero,
but the subscriber's lock had to be released, as a consequence, panic
happened.
By contrast, if we increase subscriber's refcnt before
tipc_subscrb_subscrp_delete() is called in tipc_subscrp_cancel(),
the panic issue can be avoided.
Fixes: d094c4d5f5 ("tipc: add subscription refcount to avoid invalid delete")
Reported-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the broadcast send link after 100 attempts has failed to
transfer a packet to all peers, we consider it stale, and reset
it. Thereafter it needs to re-synchronize with the peers, something
currently done by just resetting and re-establishing all links to
all peers. This has turned out to be overkill, with potentially
unwanted consequences for the remaining cluster.
A closer analysis reveals that this can be done much simpler. When
this kind of failure happens, for reasons that may lie outside the
TIPC protocol, it is typically only one peer which is failing to
receive and acknowledge packets. It is hence sufficient to identify
and reset the links only to that peer to resolve the situation, without
having to reset the broadcast link at all. This solution entails a much
lower risk of negative consequences for the own node as well as for
the overall cluster.
We implement this change in this commit.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syszkaller reported use-after-free in tipc [1]
When msg->rep skb is freed, set the pointer to NULL,
so that caller does not free it again.
[1]
==================================================================
BUG: KASAN: use-after-free in skb_push+0xd4/0xe0 net/core/skbuff.c:1466
Read of size 8 at addr ffff8801c6e71e90 by task syz-executor5/4115
CPU: 1 PID: 4115 Comm: syz-executor5 Not tainted 4.13.0-rc4+ #32
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
print_address_description+0x73/0x250 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x24e/0x340 mm/kasan/report.c:409
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:430
skb_push+0xd4/0xe0 net/core/skbuff.c:1466
tipc_nl_compat_recv+0x833/0x18f0 net/tipc/netlink_compat.c:1209
genl_family_rcv_msg+0x7b7/0xfb0 net/netlink/genetlink.c:598
genl_rcv_msg+0xb2/0x140 net/netlink/genetlink.c:623
netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2397
genl_rcv+0x28/0x40 net/netlink/genetlink.c:634
netlink_unicast_kernel net/netlink/af_netlink.c:1265 [inline]
netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1291
netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1854
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
sock_write_iter+0x31a/0x5d0 net/socket.c:898
call_write_iter include/linux/fs.h:1743 [inline]
new_sync_write fs/read_write.c:457 [inline]
__vfs_write+0x684/0x970 fs/read_write.c:470
vfs_write+0x189/0x510 fs/read_write.c:518
SYSC_write fs/read_write.c:565 [inline]
SyS_write+0xef/0x220 fs/read_write.c:557
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x4512e9
RSP: 002b:00007f3bc8184c08 EFLAGS: 00000216 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000718000 RCX: 00000000004512e9
RDX: 0000000000000020 RSI: 0000000020fdb000 RDI: 0000000000000006
RBP: 0000000000000086 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000216 R12: 00000000004b5e76
R13: 00007f3bc8184b48 R14: 00000000004b5e86 R15: 0000000000000000
Allocated by task 4115:
save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:551
kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:489
kmem_cache_alloc_node+0x13d/0x750 mm/slab.c:3651
__alloc_skb+0xf1/0x740 net/core/skbuff.c:219
alloc_skb include/linux/skbuff.h:903 [inline]
tipc_tlv_alloc+0x26/0xb0 net/tipc/netlink_compat.c:148
tipc_nl_compat_dumpit+0xf2/0x3c0 net/tipc/netlink_compat.c:248
tipc_nl_compat_handle net/tipc/netlink_compat.c:1130 [inline]
tipc_nl_compat_recv+0x756/0x18f0 net/tipc/netlink_compat.c:1199
genl_family_rcv_msg+0x7b7/0xfb0 net/netlink/genetlink.c:598
genl_rcv_msg+0xb2/0x140 net/netlink/genetlink.c:623
netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2397
genl_rcv+0x28/0x40 net/netlink/genetlink.c:634
netlink_unicast_kernel net/netlink/af_netlink.c:1265 [inline]
netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1291
netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1854
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
sock_write_iter+0x31a/0x5d0 net/socket.c:898
call_write_iter include/linux/fs.h:1743 [inline]
new_sync_write fs/read_write.c:457 [inline]
__vfs_write+0x684/0x970 fs/read_write.c:470
vfs_write+0x189/0x510 fs/read_write.c:518
SYSC_write fs/read_write.c:565 [inline]
SyS_write+0xef/0x220 fs/read_write.c:557
entry_SYSCALL_64_fastpath+0x1f/0xbe
Freed by task 4115:
save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_slab_free+0x71/0xc0 mm/kasan/kasan.c:524
__cache_free mm/slab.c:3503 [inline]
kmem_cache_free+0x77/0x280 mm/slab.c:3763
kfree_skbmem+0x1a1/0x1d0 net/core/skbuff.c:622
__kfree_skb net/core/skbuff.c:682 [inline]
kfree_skb+0x165/0x4c0 net/core/skbuff.c:699
tipc_nl_compat_dumpit+0x36a/0x3c0 net/tipc/netlink_compat.c:260
tipc_nl_compat_handle net/tipc/netlink_compat.c:1130 [inline]
tipc_nl_compat_recv+0x756/0x18f0 net/tipc/netlink_compat.c:1199
genl_family_rcv_msg+0x7b7/0xfb0 net/netlink/genetlink.c:598
genl_rcv_msg+0xb2/0x140 net/netlink/genetlink.c:623
netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2397
genl_rcv+0x28/0x40 net/netlink/genetlink.c:634
netlink_unicast_kernel net/netlink/af_netlink.c:1265 [inline]
netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1291
netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1854
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
sock_write_iter+0x31a/0x5d0 net/socket.c:898
call_write_iter include/linux/fs.h:1743 [inline]
new_sync_write fs/read_write.c:457 [inline]
__vfs_write+0x684/0x970 fs/read_write.c:470
vfs_write+0x189/0x510 fs/read_write.c:518
SYSC_write fs/read_write.c:565 [inline]
SyS_write+0xef/0x220 fs/read_write.c:557
entry_SYSCALL_64_fastpath+0x1f/0xbe
The buggy address belongs to the object at ffff8801c6e71dc0
which belongs to the cache skbuff_head_cache of size 224
The buggy address is located 208 bytes inside of
224-byte region [ffff8801c6e71dc0, ffff8801c6e71ea0)
The buggy address belongs to the page:
page:ffffea00071b9c40 count:1 mapcount:0 mapping:ffff8801c6e71000 index:0x0
flags: 0x200000000000100(slab)
raw: 0200000000000100 ffff8801c6e71000 0000000000000000 000000010000000c
raw: ffffea0007224a20 ffff8801d98caf48 ffff8801d9e79040 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801c6e71d80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff8801c6e71e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8801c6e71e80: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff8801c6e71f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8801c6e71f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function msg_reverse(), we reverse the header while trying to
reuse the original buffer whenever possible. Those rejected/returned
messages are always transmitted as unicast, but the msg_non_seq field
is not explicitly set to zero as it should be.
We have seen cases where multicast senders set the message type to
"NOT dest_droppable", meaning that a multicast message shorter than
one MTU will be returned, e.g., during receive buffer overflow, by
reusing the original buffer. This has the effect that even the
'msg_non_seq' field is inadvertently inherited by the rejected message,
although it is now sent as a unicast message. This again leads the
receiving unicast link endpoint to steer the packet toward the broadcast
link receive function, where it is dropped. The affected unicast link is
thereafter (after 100 failed retransmissions) declared 'stale' and
reset.
We fix this by unconditionally setting the 'msg_non_seq' flag to zero
for all rejected/returned messages.
Reported-by: Canh Duc Luu <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On L2 bearers, the TIPC broadcast function is sending out packets using
the corresponding L2 broadcast address. At reception, we filter such
packets under the assumption that they will also be delivered as
broadcast packets.
This assumption doesn't always hold true. Under high load, we have seen
that a switch may convert the destination address and deliver the packet
as a PACKET_MULTICAST, something leading to inadvertently dropped
packets and a stale and reset broadcast link.
We fix this by extending the reception filtering to accept packets of
type PACKET_MULTICAST.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link between two nodes come up, both endpoints will initially
send out a STATE message to the peer, to increase the probability that
the peer endpoint also is up when the first traffic message arrives.
Thereafter, if the establishing link is the second link between two
nodes, this first "traffic" message is a TUNNEL_PROTOCOL/SYNCH message,
helping the peer to perform initial synchronization between the two
links.
However, the initial STATE message may be lost, in which case the SYNCH
message will be the first one arriving at the peer. This should also
work, as the SYNCH message itself will be used to take up the link
endpoint before initializing synchronization.
Unfortunately the code for this case is broken. Currently, the link is
brought up through a tipc_link_fsm_evt(ESTABLISHED) when a SYNCH
arrives, whereupon __tipc_node_link_up() is called to distribute the
link slots and take the link into traffic. But, __tipc_node_link_up() is
itself starting with a test for whether the link is up, and if true,
returns without action. Clearly, the tipc_link_fsm_evt(ESTABLISHED) call
is unnecessary, since tipc_node_link_up() is itself issuing such an
event, but also harmful, since it inhibits tipc_node_link_up() to
perform the test of its tasks, and the link endpoint in question hence
is never taken into traffic.
This problem has been exposed when we set up dual links between pre-
and post-4.4 kernels, because the former ones don't send out the
initial STATE message described above.
We fix this by removing the unnecessary event call.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
This patch uses refcount_inc_not_zero() instead of
atomic_inc_not_zero_hint() due to absense of a _hint()
version of refcount API. If the hint() version must
be used, we might need to revisit API.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel may sleep under a rcu read lock in tipc_msg_reverse, and the
function call path is:
tipc_l2_rcv_msg (acquire the lock by rcu_read_lock)
tipc_rcv
tipc_sk_rcv
tipc_msg_reverse
pskb_expand_head(GFP_KERNEL) --> may sleep
tipc_node_broadcast
tipc_node_xmit_skb
tipc_node_xmit
tipc_sk_rcv
tipc_msg_reverse
pskb_expand_head(GFP_KERNEL) --> may sleep
To fix it, "GFP_KERNEL" is replaced with "GFP_ATOMIC".
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro tipc_wait_for_cond() is embedding the macro sk_wait_event()
to fulfil its task. The latter, in turn, is evaluating the stated
condition outside the socket lock context. This is problematic if
the condition is accessing non-trivial data structures which may be
altered by incoming interrupts, as is the case with the cong_links()
linked list, used by socket to keep track of the current set of
congested links. We sometimes see crashes when this list is accessed
by a condition function at the same time as a SOCK_WAKEUP interrupt
is removing an element from the list.
We fix this by expanding selected parts of sk_wait_event() into the
outer macro, while ensuring that all evaluations of a given condition
are performed under socket lock protection.
Fixes: commit 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
We try to make this function more readable by improving variable names
and comments, using more stack variables, and doing some smaller changes
to the logics. We also rename the function to make it consistent with
naming conventions used elsewhere in the code.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We try to make this function more readable by improving variable names
and comments, plus some minor changes to the logics.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a socket is shutting down, we notify the peer node about the
connection termination by reusing an incoming message if possible.
If the last received message was a connection acknowledgment
message, we reverse this message and set the error code to
TIPC_ERR_NO_PORT and send it to peer.
In tipc_sk_proto_rcv(), we never check for message errors while
processing the connection acknowledgment or probe messages. Thus
this message performs the usual flow control accounting and leaves
the session hanging.
In this commit, we terminate the connection when we receive such
error messages.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the checks for sockets in CONNECTING state was based on
the assumption that the incoming message was always from the
peer's accepted data socket.
However an application using a non-blocking socket sends an implicit
connect, this socket which is in CONNECTING state can receive error
messages from the peer's listening socket. As we discard these
messages, the application socket hangs as there due to inactivity.
In addition to this, there are other places where we process errors
but do not notify the user.
In this commit, we process such incoming error messages and notify
our users about them using sk_state_change().
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In filter_connect, we use waitqueue_active() to check for any
connections to wakeup. But waitqueue_active() is missing memory
barriers while accessing the critical sections, leading to
inconsistent results.
In this commit, we replace this with an SMP safe wq_has_sleeper()
using the generic socket callback sk_data_ready().
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
