This patch contains changes that allow iscsi_session_setup
to allocate private space for LLD's
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Don't turn on carrier for a non-active port
IB/mthca: Fix access to freed memory in catastrophic event handling
mlx4_core: Pass cache line size to device FW
RDMA/nes: Remove duplicate .ndo_set_mac_address field initialization
IB/mad: Fix lock-lock-timer deadlock in RMPP code
Multicast joins can succeed even if the IB port is down. This happens
when the SM runs on the same port with the requesting port. However,
IPoIB calls netif_carrier_on() when the join of the broadcast group
succeeds, without caring about the state of the IB port. The result
is an IPoIB interface in RUNNING state but without an active IB port
to support it.
If a bonding interface uses this IPoIB interface as a slave it might
not detect that this slave is almost useless and failover
functionality will be damaged. The fix checks the state of the IB
port in the carrier_task before calling netif_carrier_on().
Adresses: https://bugs.openfabrics.org/show_bug.cgi?id=1726
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
Check that the format of multicast link addresses is correct before
taking them from dev->mc_list to priv->multicast_list. This way we
never try to send a bogus address to the SA, which prevents badness
from erronous 'ip maddr addr add', broken bonding drivers, etc.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB currently must use irqsave locking for priv->lock, since it is
taken from interrupt context in one path. However, ipoib_send() does
skb_orphan(), and the network stack locking is not IRQ-safe.
Therefore we need to make sure we don't hold priv->lock when calling
ipoib_send() to avoid lockdep warnings (the code was almost certainly
safe in practice, since the only code path that takes priv->lock from
interrupt context would never call into the network stack).
Addresses: http://bugzilla.kernel.org/show_bug.cgi?id=13757
Reported-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last two drivers that need skb->dst in their start_xmit() function
Tell dev_hard_start_xmit() to no release it by unsetting IFF_XMIT_DST_RELEASE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a task did not complete normally due to a TMF, libiscsi will
now complete the task with the state ISCSI_TASK_ABRT_TMF. Drivers
like bnx2i that need to free resources if a command did not complete normally
can then check the task state. If a driver does not need to send
a special command if we have dropped the session then they can check
for ISCSI_TASK_ABRT_SESS_RECOV.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When we create the tcp/ip connection by calling ep_connect, we currently
just go by the routing table info.
I think there are two problems with this.
1. Some drivers do not have access to a routing table. Some drivers like
qla4xxx do not even know about other ports.
2. If you have two initiator ports on the same subnet, the user may have
set things up so that session1 was supposed to be run through port1. and
session2 was supposed to be run through port2. It looks like we could
end with both sessions going through one of the ports.
Fixes for cxgb3i from Karen Xie.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Network device sysfs files that grab the rtnl_lock unconditionally
will deadlock if accessed when the network device is being
unregistered. So use trylock and syscall_restart to avoid this
deadlock.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If NAPI is enabled while IPoIB's CQ is being drained, it creates a
race on priv->ibwc between ipoib_poll() and ipoib_drain_cq(), leading
to memory corruption.
The solution is to enable/disable NAPI in ipoib_ib_dev_{open/stop}()
instead of in ipoib_{open/stop}(), and sync NAPI on the INITIALIZED
flag instead on the ADMIN_UP flag. This way NAPI will be disabled when
ipoib_drain_cq() is called.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1587>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add support for new SFP+ PHY
RDMA/nes: Add wide_ppm_offset parm for switch compatibility
RDMA/nes: Fix SFP+ PHY initialization
RDMA/nes: Fix nes_nic_cm_xmit() error handling
RDMA/nes: Fix error handling issues
RDMA/nes: Fix incorrect casts on 32-bit architectures
IPoIB: Document newish features
RDMA/cma: Create cm id even when IB port is down
RDMA/cma: Use rate from IPoIB broadcast when joining IPoIB multicast groups
IPoIB: Avoid free_netdev() BUG when destroying a child interface
mlx4_core: Don't leak mailbox for SET_PORT on Ethernet ports
RDMA/cxgb3: Release dependent resources only when endpoint memory is freed.
RDMA/cxgb3: Handle EEH events
IB/mlx4: Use pgprot_writecombine() for BlueFlame pages
We have to release the RTNL before calling free_netdev() so that the
device state has a chance to become NETREG_UNREGISTERED. Otherwise
when removing a child interface, we hit the BUG() that tests the
device state in free_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
We do not need to have llds set the host no for the session's
parent, because we know the session's parent is going to be
the host. This removes it from the session creation callback
and converts the drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The qdepth setting was useful when we needed libiscsi to verify
the setting. Now we just need to make sure if older tools
passed in zero then we need to set some default.
So this patch just has us use the sht->cmd_per_lun or if
for LLD does a host per session then we can set it on per
host basis.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were using the shost work queue which ended up being
a little akward since all iscsi hosts need a thread for
scanning, but only drivers hooked into libiscsi need
a workqueue for transmitting. So this patch moves the
xmit workqueue to the lib.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is no need to cap the queue depth in the modules. We set
this in userspace and can do that there. For performance testing
with ram based targets, this is helpful since we can have very
high queue depths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iser has its own logging inrfastrucutre. Convert it to use
it instead of libiscsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove hard setting of the IB MTU used by iSER's RC queue-pair to 1K,
as this was done due to inter-op issues with an old iser target which
is not used any more.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If path_rec_start() returns error, call path_free() only if the path
was newly-created. If we free an existing path whose valid flag was zero,
(but do not detach it from the list) we cause corruption of the
path list (of which it is a member), and get a kernel crash.
The simplest solution is to not free an existing path -- just leave it
in the list as-is (i.e., with its valid flag cleared).
Thanks to Yossi Etigin of Voltaire for identifying the problem flow
which caused the kernel crash.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Moni Shua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPoIB tries to join a multicast group, and the SA module's SM
address handle is NULL (because of an SM change, etc), the join
returns with -EAGAIN status. In that case, don't print an error
message unless multicast debugging is enabled.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a deadlock between child interface creation/deletion and ipoib
start/stop. The former takes vlan_mutex, and then might take RTNL via
register_netdev()/unregister_netdev(). The latter is executed with
RTNL held, and tries to take vlan_mutex, which can lead to an AB-BA
deadlock.
Fix this by having the child interface creation/deletion code take the
RTNL first so vlan_mutex always nests inside RTNL. We can use
register_netdevice() for child interfaces because we form the
interface name from the parent interface and hence don't need the '%'
expansion of register_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After commit fe25c561 ("IPoIB: Don't enable NAPI when it's already
enabled"), if an interface is brought up but the corresponding P_Key
never appears, then ipoib_stop() will hang in napi_disable(), because
ipoib_open() returns before it does napi_enable().
Fix this by changing ipoib_open() to call napi_enable() even if the
P_Key isn't present.
Reported-by: Yossi Etigin <yosefe@Voltaire.COM>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Add dependency on INFINIBAND_ADDR_TRANS
IPoIB: Do not join broadcast group if interface is brought down
RDMA/nes: Fix for NIPQUAD removal
IPoIB: Fix loss of connectivity after bonding failover on both sides
IB/mlx4: Don't register IB device for adapters with no IB ports
mlx4_core: Fix warning from min()
IB/ehca: spin_lock_irqsave() takes an unsigned long
Fix ib_iser build to depend on INFINIBAND_ADDR_TRANS; if INET=y but
IPV6=n, then the RDMA CM is not built but INFINIBAND_ISER can be
enabled, leading to:
ERROR: "rdma_destroy_id" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_connect" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_destroy_qp" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_create_id" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_create_qp" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_resolve_route" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_disconnect" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_resolve_addr" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Because the ipoib_workqueue is not flushed when ipoib interface is
brought down, ipoib_mcast_join() may trigger a join to the broadcast
group after priv->broadcast was set to NULL (during cleanup). This
will cause the system to be a member of the broadcast group when
interface is down. As a side effect, this breaks the optimization of
setting the Q_key only when joining the broadcast group.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix bonding failover in the case both peers failover and the
gratuitous ARP is lost. In that case, the sender side will create an
ipoib_neigh and issue a path request with the old GID first. When
skb->dst->neighbour->ha changes due to ARP refresh, this ipoib_neigh
will not be added to the path->list of the path of the new GID,
because the ipoib_neigh already exists. It will not have an AH
either, because of sender-side failover. Therefore, it will not get
an AH when the path is resolved.
The solution here is to compare GIDs in ipoib_start_xmit() even if
neigh->ah is invalid. Comparing with an uninitialized value of
neigh->dgid should be fine, since a spurious match is harmless (and
astronomically unlikely too).
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We do not need to allocate a itt for data_out, so this
passes the opcode to the alloc_pdu callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This just converts iser to new alloc_pdu api. It still
preallocates the pdu, so there is no difference.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iSCSI/iSER targets may send PDUs without a prior request from the
initiator. RFC 5046 refers to these PDUs as "unexpected". NOP-In PDUs
with itt=RESERVED and Asynchronous Message PDUs occupy this category.
The amount of active "unexpected" PDU's an iSER target may have at any
time is governed by the MaxOutstandingUnexpectedPDUs key, which is not
yet supported.
Currently when an iSER target sends an "unexpected" PDU, the
initiators recv buffer consumed by the PDU is not replaced. If over
initial_post_recv_bufs_num "unexpected" PDUs are received then the
receive queue will run out of receive work requests entirely.
This patch ensures recv buffers consumed by "unexpected" PDUs are
replaced in the next iser_post_receive_control() call.
Signed-off-by: David Disseldorp <ddiss@sgi.com>
Signed-off-by: Ken Sandars <ksandars@sgi.com>
Acked-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a crash in path_rec_completion() during an SM up/down loop. If
more than one path record request is issued, the first completion
releases path->done, allowing ipoib_flush_paths() to free the path,
and thus corrupting it for the second completion.
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") added the field path->valid and changed the test "if
(!path)" to "if (!path || !path->valid)". This change made it
possible for a path with an outstanding query to pass the test and
issue another query on the same path. Having two queries on the same
path leads to a crash.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1325>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_flush_paths() can hang during an SM up/down loop: if
path_rec_start() fails (for instance, because there is no sm_ah), the
path is still added to the path list by neigh_add_path(). Then,
ipoib_flush_paths() will wait for path->done, but it will never
complete because the request was not issued at all. Fix this by
completing path->done if issuing the query fails.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1329>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a P_Key is not present when an interface is created, ipoib_open()
will return after doing napi_enable(). ipoib_open() will be called
again from ipoib_pkey_poll() when the P_Key appears, after NAPI has
already been enabled, and try to enable it again. This triggers a
BUG_ON() in napi_enable().
Fix this by moving the call to napi_enable() to after the test for
P_Key presence.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all uses of IPOIB_GID_FMT, IPOIB_GID_RAW_ARG() and IPOIB_GID_ARG()
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Reject dynamic memory add/remove when ehca adapter is present
IB/ehca: Fix reported max number of QPs and CQs in systems with >1 adapter
IPoIB: Set netdev offload features properly for child (VLAN) interfaces
IPoIB: Clean up ethtool support
mlx4_core: Add Ethernet PCI device IDs
mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC
mlx4_core: Multiple port type support
mlx4_core: Ethernet MAC/VLAN management
mlx4_core: Get ethernet MTU and default address from firmware
mlx4_core: Support multiple pre-reserved QP regions
Update NetEffect maintainer emails to Intel emails
RDMA/cxgb3: Remove cmid reference on tid allocation failures
IB/mad: Use krealloc() to resize snoop table
IPoIB: Always initialize poll_timer to avoid crash on unload
IB/ehca: Don't allow creating UC QP with SRQ
mlx4_core: Add QP range reservation support
RDMA/ucma: Test ucma_alloc_multicast() return against NULL, not with IS_ERR()
Child devices were created without any offload features set, fix this by
moving the code that computes the features into generic function which is
now called through non-child and child device creation.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
-- v1 has a bug where the 'result' flag in ipoib_vlan_add may be used uninitialized
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a get_rx_csum method. Remove the driver's own get_tso method, as
the ethtool kernel code uses the default one if nothing is provided.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a much better version of a previous patch to make the parser
tables constant. Rather than changing the typedef, we put the "const" in
all the various places where its required, allowing the __initconst
exception for nfsroot which was the cause of the previous trouble.
This was posted for review some time ago and I believe its been in -mm
since then.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Alexander Viro <aviro@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I had this in my patchset to add target reset support, but
it got dropped due to patching conflicts. This initial patch
just renames the function and users. We are actually just
dropping the session, and so this does not have anything to do
with the host exactly. It does for software iscsi because
we allocate a host per session, but for cxgb3i this makes no
sense.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the driver knows when hardware is removed like with cxgb3i,
bnx2i, qla4xxx and iser then we will want to remove the sessions/devices
that are bound to that device before removing the host.
cxgb3i and in the future bnx2i will remove the host and that will
remove all the sessions on the hba. iser can call iscsi_kill_session
when it gets an event that indicates that a hca is removed.
And when qla4xxx is hooked in to the lib (it is only hooked into
the class right now) it can call iscsi remove host like the
partial offload card drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ipoib_ib_dev_stop() does del_timer_sync(&priv->poll_timer), but if a
P_key for an interface is not found, poll_timer is not initialized, so
this leads to a crash or hang. Fix this by moving where poll_timer is
initialized to ipoib_ib_dev_init(), which is always called.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1172>.
Debugged-by: Yosef Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently, IPoIB is an LLTX driver that uses its own IRQ-disabling
tx_lock. Not only do we want to get rid of LLTX, this actually causes
problems because of the skb_orphan() done with this tx_lock held: some
skb destructors expect to be run with interrupts enabled.
The simplest fix for this is to get rid of the driver-private tx_lock
and stop using LLTX. We kill off priv->tx_lock and use
netif_tx_lock[_bh]() instead; the patch to do this is a tiny bit
tricky because we need to update places that take priv->lock inside
the tx_lock to disable IRQs, rather than relying on tx_lock having
already disabled IRQs.
Also, there are a couple of places where we need to disable BHs to
make sure we have a consistent context to call netif_tx_lock() (since
we no longer can use _irqsave() variants), and we also have to change
ipoib_send_comp_handler() to call drain_tx_cq() through a timer rather
than directly, because ipoib_send_comp_handler() runs in interrupt
context and drain_tx_cq() must run in BH context so it can call
netif_tx_lock().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") changed how paths are flushed on an SM event. This
change introduces a problem if the path record query triggered by
fails, causing path->ah to become NULL. A later successful path query
will then trigger WARN_ON() in path_rec_completion(), and crash
because path->ah has already been freed, so the ipoib_put_ah() inside
the lock in path_rec_completion() may actually drop the last reference
(contrary to the comment that claims this is safe).
Fix this by updating path->ah and freeing old_ah only when the path
record query is successful. This prevents the neighbour AH and that
path AH from getting out of sync.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1194>
Reported-by: Rabah Salem <ravah@mellanox.com>
Debugged-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Taking rtnl_lock in ipoib_mcast_join_complete() causes a deadlock with
ipoib_stop(). We avoid it by scheduling the piece of code that takes
the lock on ipoib_workqueue instead of executing it directly. This
works because we only flush the ipoib_workqueue with the RTNL not held.
The deadlock happens because ipoib_stop() calls ipoib_ib_dev_down()
which calls ipoib_mcast_dev_flush(), which calls ipoib_mcast_free(),
which calls ipoib_mcast_leave(). The latter calls
ib_sa_free_multicast(), and this waits until the multicast completion
handler finishes. This handler is ipoib_mcast_join_complete(), which
waits for the rtnl_lock(), which was already taken by ipoib_stop().
This bug was introduced in commit a77a57a1 ("IPoIB: Fix deadlock on
RTNL in ipoib_stop()").
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c8c2afe3 ("IPoIB: Use rtnl lock/unlock when changing device
flags") added a call to rtnl_lock() in ipoib_mcast_join_task(), which
is run from the ipoib_workqueue. However, ipoib_stop() (which is run
inside rtnl_lock()) flushes this workqueue, which leads to a deadlock
if the join task is pending.
Fix this by simply not flushing the workqueue from ipoib_stop(). It
turns out that we really don't care about workqueue tasks running
during or after ipoib_stop(), as long as we make sure to flush the
workqueue before unregistering a netdev.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1114>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are users that are running UDP applications that require a large
receive queue size in order to get good performance. To prevent
allocation failures for rx_rings when using non-SRQ mode and large
recv_queue_size (1K or larger), use vmalloc() instead of kcalloc() to
alocate rx_rings.
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
wr->sg_list should be set to the sge pointer passed in, not
priv->cm.rx_sge.
Reported-by: Hoang-Nam Nguyen <HNGUYEN@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The help text for INFINIBAND_IPOIB_DEBUG refers to "ipoib_debugfs,"
which no longer exists. Correct this to talk about the files under
debugfs that are really created.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Connected mode is now tested and used by lots of people. No need to
hide it under CONFIG_EXPERIMENTAL.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Print the return code of ib_sa_path_rec_get() if it fails to help
debug errors.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enhance iser to act upon notification on network stack changes that
make its RDMA connection unaligned with the link used by the stack for
the <src,dst> IPs used to establish the connection.
When RDMA_CM_EVENT_ADDR_CHANGE arrives, just disconnect the
connection, assuming that the user space iscsid daemon will reconnect,
and the new connection will be aligned with the IP stack.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
[SCSI] scsi_dh: fix kconfig related build errors
[SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
[SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
[SCSI] make struct scsi_{host,target}_type static
[SCSI] fix locking in host use of blk_plug_device()
[SCSI] zfcp: Cleanup external header file
[SCSI] zfcp: Cleanup code in zfcp_erp.c
[SCSI] zfcp: zfcp_fsf cleanup.
[SCSI] zfcp: consolidate sysfs things into one file.
[SCSI] zfcp: Cleanup of code in zfcp_aux.c
[SCSI] zfcp: Cleanup of code in zfcp_scsi.c
[SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
[SCSI] zfcp: Small QDIO cleanups
[SCSI] zfcp: Adapter reopen for large number of unsolicited status
[SCSI] zfcp: Fix error checking for ELS ADISC requests
[SCSI] zfcp: wait until adapter is finished with ERP during auto-port
[SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
[SCSI] sg: Add target reset support
[SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
[SCSI] sd: Move scsi_disk() accessor function to sd.h
...
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_addr_{lock,unlock}{,_bh}() helpers.
Use them to protect operations that operate on or read
the network device unicast and multicast address lists.
Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase IPoIB ring sizes to twice their original sizes (RX: 128->256,
TX: 64->128) to act as a shock absorber for high traffic peaks. With
the current settings, we have seen cases that there are many calls to
netif_stop_queue(), which causes degradation in throughput. Also,
larger receive buffer sizes help IPoIB in CM mode to avoid experiencing
RNR NAK conditions due to insufficient receive buffers at the SRQ.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since IPoIB connected mode does not NETIF_F_SG, we only have one DMA
mapping per send, so we don't need a mapping[] array. Define a new
struct with a single u64 mapping member and use it for the CM tx_ring.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the driver sets the MTU of the net device outside of its
change_mtu method, it should make use of dev_set_mtu() instead of
directly setting the mtu field of struct netdevice. Otherwise
functions registered to be called upon MTU change will not get called
(this is done through call_netdevice_notifiers() in dev_set_mtu()).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use of this lock is required to synchronize changes to the netdvice's
data structs. Also move the call to ipoib_flush_paths() after the
modification of the netdevice flags in set_mode().
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_mcast_detach() does nothing except call ib_detach_mcast(), so just
use the core API in the one place that does a multicast group detach.
add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-105 (-105)
function old new delta
ipoib_mcast_leave 357 319 -38
ipoib_mcast_detach 67 - -67
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current code will set the Q_Key for any join of a non-sendonly
multicast group. The operation involves a modify QP operation, which
is fairly heavyweight, and is only really required after the join of
the broadcast group. Fix this by adding a parameter to ipoib_mcast_attach()
to control when the Q_Key is set.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
No need for a mutex around calls to ib_attach_mcast/ib_detach_mcast
since these operations are synchronized at the HW driver layer.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPOIB_MCAST_STARTED flag is not used at all since commit b3e2749b
("IPoIB: Don't drop multicast sends when they can be queued"), so
remove it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The patch tries to solve the problem of device going down and paths being
flushed on an SM change event. The method is to mark the paths as candidates for
refresh (by setting the new valid flag to 0), and wait for an ARP
probe a new path record query.
The solution requires a different and less intrusive handling of SM
change event. For that, the second argument of the flush function
changes its meaning from a boolean flag to a level. In most cases, SM
failover doesn't cause LID change so traffic won't stop. In the rare
cases of LID change, the remote host (the one that hadn't changed its
LID) will lose connectivity until paths are refreshed. This is no
worse than the current state. In fact, preventing the device from
going down saves packets that otherwise would be lost.
Signed-off-by: Moni Levy <monil@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add "ipoib_use_lro" module parameter to enable LRO and an
"ipoib_lro_max_aggr" module parameter to set the max number of packets
to be aggregated. Make LRO controllable and LRO statistics accessible
through ethtool.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set IB_QP_CREATE_BLOCK_MULTICAST_LOOPBACK for IPoIB's UD QPs if
supported by the underlying device. This creates an improvement of up
to 39% in bandwidth when sending multicast packets with IPoIB, and an
improvment of 12% in cpu usage.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For devices that don't support SRQs, ipoib_cm_post_receive_nonsrq() is
called from both ipoib_cm_handle_rx_wc() and ipoib_cm_nonsrq_init_rx(),
and these two callers are not synchronized against each other.
However, ipoib_cm_post_receive_nonsrq() always reuses the same receive
work request and scatter list structures, so multiple callers can end
up stepping on each other, which leads to posting garbled work
requests.
Fix this by having the caller pass in the ib_recv_wr and ib_sge
structures to use, and allocating new local structures in
ipoib_cm_nonsrq_init_rx().
Based on a patch by Pradeep Satyanarayana <pradeep@us.ibm.com> and
David Wilder <dwilder@us.ibm.com>, with debugging help from Hoang-Nam
Nguyen <hnguyen@de.ibm.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The connected mode implementation in the IPoIB driver has a large
overhead in the way SKBs are handled in the receive flow. It usually
allocates an SKB with as big as was used in the currently received SKB
and moves unused fragments from the old SKB to the new one. This
involves a loop on all the remaining fragments and incurs overhead on
the CPU. This patch, for small SKBs, allocates an SKB just large
enough to contain the received data and copies to it the data from the
received SKB. The newly allocated SKB is passed to the stack and the
old SKB is reposted.
When running netperf, UDP small messages, without this pach I get:
UDP UNIDIRECTIONAL SEND TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
14.4.3.178 (14.4.3.178) port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
114688 128 10.00 5142034 0 526.31
114688 10.00 1130489 115.71
With this patch I get both send and receive at ~315 mbps.
The reason that send performance actually slows down is as follows:
When using this patch, the overhead of the CPU for handling RX packets
is dramatically reduced. As a result, we do not experience RNR NAK
messages from the receiver which cause the connection to be closed and
reopened again; when the patch is not used, the receiver cannot handle
the packets fast enough so there is less time to post new buffers and
hence the mentioned RNR NACKs. So what happens is that the
application *thinks* it posted a certain number of packets for
transmission but these packets are flushed and do not really get
transmitted. Since the connection gets opened and closed many times,
each time netperf gets the CPU time that otherwise would have been
given to IPoIB to actually transmit the packets. This can be verified
when looking at the port counters -- the output of ifconfig and the
oputput of netperf (this is for the case without the patch):
tx packets
==========
port counter: 1,543,996
ifconfig: 1,581,426
netperf: 5,142,034
rx packets
==========
netperf 1,1304,089
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
The SRP initiator is currently using ib_find_cached_pkey() and
ib_get_cached_gid() in situations where the uncached ib_find_pkey()
and ib_query_gid() functions serve just as well: sleeping is allowed
and performance is not an issue. Since we want to eliminate the
cached operations in the long term, convert SRP to use the uncached
variants.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes two bugs that are related.
1. Old tools did not set can_queue/cmds_max. This patch modifies
libiscsi so that when we add the host we catch this and set it
to the default.
2. iscsi_tcp thought that the scsi command that was passed to
the eh functions needed a iscsi_cmd_task allocated for it. It
only needed a mgmt task, and now it does not matter since it
all comes from the same pool and libiscsi handles this for the
drivers. ib_iser had copied iscsi_tcp's code and set can_queue
to its max - 1 to handle this. So this patch removes the max -1,
and just sets it to the max.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The recv lock was defined so the iscsi layer could block
the recv path from processing IO during recovery. It
turns out iser just set a lock to that pointer which was pointless.
We now disconnect the transport connection before doing recovery
so we do not need the recv lock. For iscsi_tcp we still stop
the recv path incase older tools are being used.
This patch also has iscsi_itt_to_ctask user grab the session lock
and has the caller access the task with the lock or get a ref
to it in case the target is broken and sends a tmf success response
then sends data or a response for the command that was supposed to
be affected bty the tmf.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds two new attrs used for creating initiator ports and
binding sessions to hardware.
The session level initiatorname:
Since bnx2i does a scsi_host per host device, we need to add the
iface initiator port settings on the session, so we can create
multiple initiator ports (each with different inames) per device/scsi_host.
The current iname reflects that qla4xxx can have one iname per hba, and we are
allocating a host per session for software. The iname on the host will
remain so we can export and set the hba level qla4xxx setting.
The ifacename attr:
To bind a session to a some peice of hardware in userspace we maintain
some mappings, but during boot or iscsid restart (iscsid contains the user
space part of the driver) we need to be able to figure out which of those
host mappings abstractions maps to certain sessions. This patch adds
a ifacename attr, which userspace can set to id the host side of the
endpoint across pivot_roots and iscsid restarts.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This hooks iser into the iscsi endpoint code. Previously it handled the
lookup and allocation. This has been made generic so bnx2i and iser can
share it. It also allows us to pass iser the leading conn's ep, so we
know the ib_deivce being used and can set it as the scsi_host's parent.
And that allows scsi-ml to set the dma_mask based on those values.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently we duplicate the list of sessions, because we were using the
test for if a session was on the host list to indicate if the session
was bound or unbound. We can instead use the target_id and fix up
the class so that drivers like bnx2i do not have to manage the target id
space.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This handles the iscsi_cmd_task rename and renames
the iser cmd task to iser task.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert ib_iser to support merged tasks.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
