Using wrong chainmasks would have an adverse impact on performance.
This patch fixes chainmask retrieval for non-PCIE cards.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OLC_FOR_AR9280_20_LATER is defined in multiple places,
move it to a common location.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reset automatically the TSF on re-enabling beaconing after scanning
in IBSS mode causes several problems. For example a new created IBSS
network can't age before an other node has joined, because scans are
done automatically in that case. And several other strange bugs more...
The TSF reset is done manually in the higher level mac80211 code in
the cases were it's needed, so we don't need to do it here.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the old days we used one slot per frame. But when we changed that to 2,
we didn't raise the overall slot count. Which resulted in an effective
division of two to the number of slots.
Double the number of TX slots, so we have an effective hardware queue
of 128 frames per QoS queue.
Also optimize the TX header cache handling. We don't need a cached TX header
for slots that will never carry an actual header.
So we reduce the memory consumption of the cache by 50%.
So as a net result we end up with more or less the same memory usage before
and after this patch (except a few tiny meta structures), but have twice
the number of TX slots available.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes hidden bugs in the size handling of the DMA buffers.
This sets the RX buffer size to the theoretical max packet size and
fixes passing of the size values to the device (must not subtract the header offset).
These bugs are hidden and don't actually trigger due to the magic +100
offset for the buffer size.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the DMA stop sanity check up a few lines, so it's actually
theoretically possible to trigger. (But it still shouldn't trigger, of course).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Passing beacons received from other BSS to s/w in non-scanning
state is unnecessary in STA mode. This patch filters them out in
h/w.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When iwlwifi runs on IOMMU, IOMMU generates a lot of PTE write faults
because PTE write bit is not set on some of PTE's. This is because iwlwifi
driver calls DMA mapping with PCI_DMA_TODEVICE which is read only in mapping
PTE. But iwlwifi device actually writes to the mapped page to update its contents.
This issue is not exposed in swiotlb. But VT-d hardware can capture this fault and
stop the fault transaction.
The iwl TX command contains a scratch field that is updated by uCode to
indicate retry counts. For 5000 series the patch is required also for
regular frames, but this patch does not differenciate.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch unifies use of SW rfkill between 3945 and agn driver.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes duplicate code from iwl3945 and uses
iwl_rx_reply_error and spectrum notifications from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes duplicate rx handlers(pm_sleep and pm_debug) from 3945 and
uses handlers from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_mac_hw_scan callback instead of
iwl3945_mac_hw_scan callback.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch makes use of iwl_rx_scan handler for 3945.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
at76_debug should be an unsigned int as it used as a bit field. In
fact, modprobe fails when trying to set at76_debug's high bit.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the latest mac80211 stack, the driver needs to be updated for
cfg80211 scanning. I based the changes off of modifications for
at76_usb found here:
http://johannes.sipsolutions.net/patches/old/all/2008-09-19-13:35/020-cfg80211-scan.patch
The trick was that max_signal also needs to be set to avoid a divide
by zero Oops. I just guessed and used the value 100 for now.
kvalo: handpicked the change from two different patches
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a driver for usb devices based on at76c50x chipset. This is
a mac80211 port of the original at76_usb driver.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Default to MAX_UCODE_BEACON_INTERVAL if the output of
iwl_adjust_beacon_interval would otherwise be zero. This prevents a
division by zero on my iwl5300-equipped Lenovo T400 with kernels that
include "mac80211: use cfg80211s BSS infrastructure".
This patch is a bit of a hack -- I'm not sure why iwl_setup_rxon_timing
is giving iwl_adjust_beacon_interval a zero input (which is the only way
it would output zero). I would be happy to have a better fix. But for
now, this makes my box boot...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch expands the parenthesis in the txctl reg write
of the LO calibration to enforce precedence rules.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scanned BSS entries are timestamped with jiffies, which doesn't
increment across suspend and hibernate. On resume, every BSS in the
scan list looks like it was scanned within the last 10 seconds,
irregardless of how long the machine was actually asleep. Age scan
results on resume with the time spent during sleep so userspace has a
clue how old they really are.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs don't start BA negotiation with the client before it is done
with the key handshake in WPA/RSN. With those APs, key handshake times
out if EAPOL frames are sent after addba request. So defer the BA negotiation
until we are done with tx/rx of all EAPOL frames.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The word_base is in bytes instead of word index number,
this means that when using it, it should be transformed into
a word index first.
Otherwise RF register reading will fail through debugfs since
we would start reading 4 words starting with word 4 (which is the last
valid word for RF).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting up the CAB queue requires only the beacon interval,
remove the function ath_get_beaconconfig() which is redundant.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set channel change time to 5ms, this will improve scan results.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX and calibration have different timeout requirements.
This patch fixes it by changing the HW wait routine
to accept a timeout value.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch programs the RTC registers of AR9100 chipsets
correctly during chip reset.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RTS and CTS-to-self duration needs to go after ICV len is considered.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently send beacons directly from the interrupt routine. This
can hold up interrupt processing in beaconing modes and makes the
ISR somewhat more complex. Move it to a tasklet like rx and tx.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_reset can be called from process context, which in turn can
call ath5k_beacon_config which takes the sc->block spinlock. Since
it can also be taken in hard irq context, use spin_lock_irqsave
everywhere. This fixes a potential deadlock in adhoc mode.
Changes-licensed-under: 3-Clause-BSD
Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since interrupts are already masked by the hardware, there's no need to
discard interrupt bits in the ISR itself. Also, in ath5k_beacon_config
we mask off a couple of bits without locking, so doing this mask in
software can lead to unhandled beacon timer and beacon miss interrupts.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only way rf_write() can be called with word 0 is
when the user sends the wrong word index through debugfs.
However the values which are send through debugfs are
validated using the RF_BASE and RF_SIZE macro values,
the most logical solution is to increase RF_BASE with 4
and decrease RF_SIZE with 4 (RF_SIZE has always been
1 word too big)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The atomic requirement for get_tsf() has been removed
by mac80211. This means the USB drivers can add support
for the callback function again.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes:
- iwlwifi is an optional driver and should thus not default to 'y'.
- 3945 now depends on IWLCORE.
Rework:
- There is not a case when IWLCORE should not be selected. At the same time
the driver does not use IWLWIFI or IWLCORE. We can just merge the usage of
these two. With IWLWIFI being the driver name we proceed to use just it and
replace instances of IWLCORE with it. The module name does not change
and is still iwlcore.
- Both IWLAGN and IWL3945 are selecting FW_LOADER, we can thus just move
this up to one select when IWLWIFI is selected.
- IWL5000 now supports Intel Wireless Wifi 100, 6000, and 6050 series.
- Now that 3945 depends on IWLWIFI we can also indicate its dependency on
MAC80211_LEDS and LEDS_CLASS at this level.
- IWLAGN_LEDS is not used by driver - remove it.
- IWLAGN_SPECTRUM_MEASUREMENT actually depends on IWLWIFI as it forms part
of iwlcore module. Move this config up in Kconfig to reflect that and also
change name to IWLWIFI_SPECTRUM_MEASUREMENT.
- CONFIG_IWLWIFI_RFKILL is used by iwlagn as well as iwl3945, add text to
description that indicates this.
- CONFIG_IWL3945_RFKILL does not exist - remove usage from driver.
- Add "iwlagn" to end of description of IWLAGN to help people understand
what iwlagn means in rest of Kconfig text.
- Add "iwl3945" to end of description of IWL3945 to help people understand
what iwlagn means in rest of Kconfig text.
- Change IWLWIFI_DEBUGFS description to indicate that only iwlagn supports
it (for now).
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use one workqueue instead of one per CPU.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- some of them are defined as follows:
#define ipw_write32 expr1; expr2
and are called from loops or ifs without a compound statement, so
they are broken. Fix it by putting them into do {} while (0) for
writes and ({ }) for reads.
- also unify and cleanup them while at it -- convert them from
macros to inline functions, so that we get some basic typechecking
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Cc: James Ketrenos <jketreno@linux.intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both branches of the regulatory check in ath_attach() set up a
custom regulatory domain and apply radar and world flags, so extract
those into a single path.
While at it, fix a couple of spelling errors and an unnecessary extra
pointer traversal.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_regd_get_current_country() doesn't exist.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function ath9k_regd_get_rd() is unused.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Write isWwrSKU as an inline function and nix the camel-case to make
the routine slightly clearer. Change its argument to take the regd
value directly so it can eventually be used by ath5k as well.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we already have a stack variable to track the eeprom regd,
we can grab it up front it and save three calls to fetch it again.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current_rd_inuse regulatory value is assigned but not used anywhere.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids triggering a BUG_ON in pci_disable_msi in the error path.
Furthermore remove the first call to pci_disable_device as it is already
called at out_pci_disable_device.
Both issues were introduced in the patch "iwlagn: fix hw-rfkill while
the interface is down".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds Open Loop Control support for Atheros chipsets that
supports open loop power control.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The existing value was too conservative, causing
the history buffer not to be updated.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ANI, where the MIB counters were
being cleared before the stats were updated.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch lays the groundwork for handling TSF Out of Range
interrupt, which will be used for power save later on.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables Fractional N mode for all channel
if the EEPROM says so, and also fixes the INI only
when the device is not a 2 GHz only capable device.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9285 chipsets have a different EEPROM layout,
handle this appropriately when populating the rd_ext
capability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where the max power level
was being calculated incorrectly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only ipw2x00 now uses it. Reduce confusion. Profit!
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So that net/ieee80211.h can be made private to ipw2x00 in a follow-up.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Test arraysize before an element of the array.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem: "iwconfig ethX power on" returns error
The cause: "ps_supported" flag was never set for SD8385/8686
The fix: check firmware capabilities returned by GET_HW_SPEC command.
Set "ps_supported" to 1 if FW_CAPINFO_PS bit is on. This fix applies
to SDIO interface only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a wrong check on num_txbdfree. It could lead to
num_txbdfree become nagative. Result was that the gianfar stops
sending data.
Changes from first version :
- removed a space between parens (David Millers comment)
- full email address in signed off line
Signed-off-by: Rini van Zetten <rini@arvoo.nl>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend copyright into 2009 and update address.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch by Jaswinder Singh <jaswinder@infradead.org>.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware blob is little endian.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the copyright to 2009 and updates the version number
to 3.98.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds version reporting for hardware selfboot.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to report the DASH firmware version.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to obtain the bootcode version for versions
of bootcode that do not use the new method.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reorganizes the firmware version routines in preparation for
the following patches.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remaining uses of tg3_nvram_read_swab() either intended to read the
data from NVRAM exactly as tg3_nvram_read_be32() did or hide deeper
interpretations of the data. For the former case, a direct replacement
of tg3_nvram_read_swab() with tg3_nvram_read_be32() is in order. For
the latter case, we remove tg3_nvram_read_swab() and document what the
code is really doing.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any software requesting NVRAM data as it exists on NVRAM is necessarily
requesting that the results be returned as a bytestream. A bytestream
data read in from the device can also be thought to be in big endian
format. Therefore, all the LE notations in the driver are mislabeled.
This patch converts all LE notations to BE notations, carefully
evaluating the surrounding code in the process.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the blind byteswap of NVRAM data as it is read in.
To preserve the logic at the call sites, this patch also inverts every
call to tg3_nvram_read() and tg3_nvram_read_swab(). The call swap gets
confusing within tg3_nvram_read_le() (LE is a misnomer), but the reader
should be able to convince himself / herself that the resulting behavior
is still unchanged.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves all NVRAM routines earlier in the source file to
eliminate forward declarations.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_vlan_rx_register() touches the hardware if netif_running() returns
false. This patch fixes the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool interface has acquired some new enumerations since the
tg3 driver's tg3_set_settings() error checking code was written. The
error checking code is no longer complete. This patch rewrites the
error checking so that it is future-proofed.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware's MTU is configured so that it will accept packets whose
VLAN tag is left inline. This means that the hardware will also accept
other packets larger than the desired MTU size. This patch checks for
and discards packets that are larger than the requested MTU but are not
VLAN tagged frames.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6833c043f9 introduced the phy
auto-powerdown capability. While the APD feature only works for 5761
and 5784 asic revisions, the (harmless portion of the) code was applied
to all 5705 and newer devices. However, the 5906 phy departs from the
usual design. This commit was interfering with the 5906's ability to
negotiate link against some switches. This patch corrects the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is really no need for function just doing simple kfree()
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to reclaim the same USB interface beeing probed.
Releasing interface does nothing also.
This is already in for a long time in off-kernel hso driver
and no regresions were noticed for this change.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ColdFire CPU specific setup from here. The ColdFire
CPU platform code now sets up all this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable the SSB core on device shutdown.
This has two advantages:
1) A clean device shutdown is always desired here, because we disable
the device's global crystal in the next statement.
2) This fixes a bug where the device will come up with the enable-bit
set on the next initialization (without a reboot inbetween).
This causes breakage on the second initialization due to code that
checks this bit (ssb_device_is_enabled() checks).
Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unconditionally setup the IRQ routing on chip reset.
It's safe to call ssb_pcicore_dev_irqvecs_enable() unconditionally, because
it has internal checks for redundant calls.
This fixes problems where hardware will not come up properly
due to quirks in the enable-bit hardware.
Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This organizes a few calls into a function table to enable adding new
devices.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not a logical change but rather a move of the inbound firmware event
handler into it's own function as it will later be called by the outbound
path.
The addition of the mutex is to create exclusive access to the mailbox
commands between inbound and outbound handling.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function for performing the reset rather than in-line. This function
may later be called by a core dump process.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hp-plus needs to call __alloc_eip_netdev() instead of
__alloc_ei_netdev() since it is linked with 8390p.o.
Fixes this build error:
ERROR: "__alloc_ei_netdev" [drivers/net/hp-plus.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mesh and radiotap interfaces need to use the same private data as
the main wifi interface. If the main wifi interface uses netdev_priv(),
but the other interfaces ->ml_priv, there's no way to figure out where
the private data actually is in the WEXT handlers and netdevice
callbacks. So make everything use ->ml_priv.
Fixes botched netdev_priv() conversion introduced by "netdevice
libertas: Fix directly reference of netdev->priv", though admittedly
libertas' use of ->priv was somewhat "special".
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When iwlan runs on IOMMU, IOMMU generates a lot of PTE write faults
because PTE write bit is not set on some of PTE's. This is because
iwlan driver calls DMA mapping with PCI_DMA_TODEVICE which is read only
in mapping PTE. But iwlan device actually writes to the mapped page to
update its contents. This issue is not exposed in swiotlb. But VT-d
hardware can capture this fault and stop the fault transaction.
The following patch fixes the issue.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds two new device ids to the asix driver.
One comes directly from the asix driver on their web site, the other was
reported by Armani Liao as needed for the MSI X320 to get the driver to
work properly for it.
Reported-by: Armani Liao <aliao@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are two paths for filling rx buffer queues. One is
used during initialization and the other during runtime. This patch
removes ql_alloc_sbq_buffers() and ql_alloc_lbq_buffers() and replaces
them with a call to the runtime functions ql_update_lbq() and
ql_update_sbq().
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Buffers are refilled in chunks of 16 at a time before notifying the
hardware with a register write. This can cause several writes to take
place in a given napi poll call. This change causes the write to take place
only once at the end of the call.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of taking/giving the hw semaphore repeatedly when iterating over
several frame to queue route settings, we have the caller hold it until
all are done.
This reduces PCI bus chatter and possible waits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of taking/giving the semaphore repeatedly when iterating over
several adderesses, we have the caller hold it until all are done. This
reduces PCI bus chatter and possible waits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting MAC addresses and routing frames to various queues will need to
be done in response to firmware events as well as during initialization.
This change encapsulates the facilities into a single call that can
later me made from other places.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A receive coalescing timeout of 250 usec appears to strike a good
balance between allowing enough received frames to be aggregated for
LRO to do its job and not allowing the connection to stall due to
delaying ACKs to the remote end for too long.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the netif_carrier_off() call in ->open() to port probe, so that
ethtool doesn't report the link as being up before we have up'd the
interface.
Move initialisation of the rx/tx coalescing timers from ->open() to
port probe, so that we don't reset the coalescing timers every time
the interface is up'd.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split pci probe function into smaller logical blocks.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it was pointed out on the list that ixgbe was failing when using 64kB pages
and large 16kB MTU.
since with a 64kB PAGE_SIZE MAX_SKB_FRAGS = 3, the way the driver was
configuring page usage was assuming 2kB is half a page, and was only
ever dmaing that much data to a half page.
(16kB - header size) / 2048 = 7 or 8 pages, which would far exceed 3
adjust the driver to account for these large pages, the hardware can
support DMA to up to 16kB for each descriptor.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Shannon Nelson <shannon.nelson@intel.com>
The ring_feature member of ixgbe_adapter is statically allocated based on
the supported features of the device. When a new feature is added, we need
to manually update the static allocation. This patch makes the feature
list an enum, eliminating the need for multiple updates to the code when
adding a new feature.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI bar 0 is used for memory mapped register access.
If ioremap fails (returns NULL), register access results
in crash.
Use pci_ioremap_bar() instead of ioremap(), the latter
fails on on 32 bit powerpc where pci resource address is
> 32 bits.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI function to physical port mapping is valid only for
old firmware. New firmware (4.0.0+) abstracts this.
So driver should never try to access phy using invalid
mapping. The behavior is unpredictable when PCI functions
4-7 are enabled on the same NIC.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix double free at netns creation
veth : add the set_mac_address capability
sunlance: Beyond ARRAY_SIZE of ib->btx_ring
sungem: another error printed one too early
ISDN: fix sc/shmem printk format warning
SMSC: timeout reaches -1
smsc9420: handle magic field of ethtool_eeprom
sundance: missing parentheses?
smsc9420: fix another postfixed timeout
wimax/i2400m: driver loads firmware v1.4 instead of v1.3
vlan: Update skb->mac_header in __vlan_put_tag().
cxgb3: Add support for PCI ID 0x35.
tcp: remove obsoleted comment about different passes
TG3: &&/|| confusion
ATM: misplaced parentheses?
net/mv643xx: don't disable the mib timer too early and lock properly
net/mv643xx: use GFP_ATOMIC while atomic
atl1c: Atheros L1C Gigabit Ethernet driver
net: Kill skb_truesize_check(), it only catches false-positives.
net: forcedeth: Fix wake-on-lan regression
Add new USB ID codes. These come from two postings on forums and
mailing lists, and four are derived from the .inf that accompanies
the latest Realtek Windows driver for the RTL8187L.
Thanks to Viktor Ilijašić <viktor.ilijasic@gmail.com> and Xose Vazquez
Perez <xose.vazquez@gmail.com> for reporting these new ID's.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With DEBUG_NOTIFIERS it results in
[11330.890966] WARNING: at /home/bor/src/linux-git/kernel/notifier.c:88
notifier_call_chain+0x91/0xa0()
[11330.890977] Hardware name: PORTEGE 4000
[11330.890983] Invalid notifier called! ...
Without DEBUG_NOTIFIERS it most likely crashes on NULL pointer.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 8390 driver was structured by Al Viro to allow the flexibility
required by platforms. lib8390.c contains the core code which drivers
explicitly include:
- 8390.c includes lib8390.c to provide the standard ISA based driver.
- etherh.c includes it with the accessors defined for RiscPC platforms,
where it is addressed via the MMIO accessors with a device dependent
register spacing.
Other platform drivers do something similar.
However, b9a9b4b caused the kernel to contain not only the etherh
private build of lib8390 (included in etherh.c) but also lib8390.c
itself, and referred the new net_device_ops methods to the ISA version.
The result of this is is not pretty:
Unable to handle kernel paging request at virtual address 12032030
pgd = c8330000
[12032030] *pgd=00000000
Internal error: Oops: 18331805 [#1]
Modules linked in: ipv6
CPU: 0 Not tainted (2.6.29-rc3 #167)
PC is at do_set_multicast_list+0xd0/0x190
LR is at bitrev32+0x28/0x34
pc : [<c017aab4>] lr : [<c0139120>] psr: a0000093
sp : c8321d9c ip : c8321d84 fp : c8321dbc
r10: c80c6800 r9 : 00000000 r8 : c80c6b60
r7 : c80c6b80 r6 : cc80c800 r5 : c80c6800 r4 : 00000000
r3 : cc80c80c r2 : 00000004 r1 : 00000007 r0 : e0000000
Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
...
Fix up b9a9b4b by making etherh's net_device_ops refer to the internal
lib8390 functions, and remove the build of the ISA 8390.c driver.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Further to a71558d, this is round five of fixes to make etherh work
again. As mainline kernels stand, the fixes in b9a9b4b were the wrong
approach.
The 8390 driver was structured by Al Viro to allow the flexibility required
by platforms. lib8390.c contains the core code which drivers explicitly
include:
- 8390.c includes lib8390.c to provide the standard ISA based driver.
- etherh.c includes it with the accessors defined for RiscPC platforms,
where it is addressed via the MMIO accessors with a device dependent
register spacing.
Other platform drivers do something similar.
However, b9a9b4b caused the kernel to contain not only the etherh private
build of lib8390 (included in etherh.c) but also lib8390.c itself, and
referred the new net_device_ops methods to the ISA version. The result
of this is is not pretty:
Unable to handle kernel paging request at virtual address 12032030
pgd = c8330000
[12032030] *pgd=00000000
Internal error: Oops: 18331805 [#1]
Modules linked in: ipv6
CPU: 0 Not tainted (2.6.29-rc3 #167)
PC is at do_set_multicast_list+0xd0/0x190
LR is at bitrev32+0x28/0x34
pc : [<c017aab4>] lr : [<c0139120>] psr: a0000093
sp : c8321d9c ip : c8321d84 fp : c8321dbc
r10: c80c6800 r9 : 00000000 r8 : c80c6b60
r7 : c80c6b80 r6 : cc80c800 r5 : c80c6800 r4 : 00000000
r3 : cc80c80c r2 : 00000004 r1 : 00000007 r0 : e0000000
Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
...
Fix up b9a9b4b by making etherh's net_device_ops refer to the internal
lib8390 functions, and remove the build of the ISA 8390.c driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failure happens when an interrupt occurs and the driver is reading
EICR. This read will cause a clear-by-read which leads to two TLP
being inserted in the PCIe retry buffer leading to an overflow of the
buffer and corruption of TLPs.
The solution is different depending where the reading of EICR takes place.
For ixgbe_msix_lsc() since we are in MSIX mode and know OCD is enabled a
clear-by-write is done instead of the normal clear-by-read.
For ixgbe_intr() 0xffffffff is written to EIMC before the read, masking the
interrupts.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a postfix decrement timeouts will reach -1 rather than 0, so
the error path does not appear.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added missing set_bit() to disable data transfer when a memchange
notification is handled
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool.h says the driver should set the magic field in get_eeprom and
verify it in set_eeprom. This patch adds this functionality using an
arbitary driver-specific magic value constant (0x9420).
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin recently fixed several instances where variables reach -1,
but 0 is tested afterwards. This patch fixes another, so the timeout
will be correctly detected and a warning printed.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a one liner change to have the driver use by default the v1.4
of the i2400m firmware instead of v1.3. The v1.4 version of the
firmware has been submitted to David Woodhouse for inclusion in the
linux-firmware tree and it is already available at
http://linuxwimax.org/Download.
The reason for this change is that the 1.3 release of the user space
software and firmware has a few issues that will make it difficult to
use with currently deployed commercial networks such as Xohm and
Clearwire.
As well, the new 1.4 release of the user space software (which matches
the 1.4 firmware) has intermitent issues with the 1.3 firmware.
The 1.4 release in http://linuxwimax.org/Download has been widely
deployed and tested with the codebase in 2.6.29-rc, the 1.4 firmware
and the 1.4 user space components.
We understand it is quite late in the rc process for such a change,
but would like to ask for the change to be taken into consideration.
Alternatively, a user could always force feed a 1.4 firmware into a
driver that doesn't have this modification by:
$ cd /lib/firmware
$ mv i2400m-fw-usb-1.3.sbcf i2400m-fw-usb-1.3.real.sbcf
$ ln -sf i2400m-fw-usb-1.4.sbc i2400m-fw-usb-1.3.sbcf
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code adds a module parameter called num_vfs which defines if the
driver should attempt to use sr-iov and if so how many VFs should be
enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support to handle requests from the VF to perform
operations such as completing resets, setting/reading mac address, adding
vlans, adding multicast addresses, setting rlpml, and general
communications between the PF and all VFs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the pf portion of vmdq support. This provides enough support so that
VMDq is enabled, and the pf is functional without enabling vfs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first step in supporting sr-iov. The vf_allocated_count value
will be 0 until we actually have vfs present. In the meantime it
represents an offset value for the start of the queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb is currently not returning the correct values for napi. In addition it
is doing more work than necessary since it will not exit polling until
work_done is equal to zero.
This patch makes the following changes:
1. Consolidates msi-x and non-msi polling routines.
2. Corrects return values for polling routines.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the unused macro PAGE_USE_COUNT(), since there is no more reference
to it. The last reference was removed by Jesse's commit number
630b25cdf4.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Move variable declaration as far inner as possible.
Fix this sparse warning:
drivers/net/igb/igb_main.c:1895:21: warning: symbol 'j' shadows an earlier one
drivers/net/igb/igb_main.c:1855:16: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the move of support for PCIe devices from e1000 to e1000e, this
workaround necessary only for older non-PCIe devices was mistakenly
copied into e1000e. Remove it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To match ixgbe GRO functionality, we remove the LRO (which is now GRO)
Kconfig option which enables GRO by default.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced support for link speed and duplex setting (ethtool -s),
link advertising parameters and autonegotiation (ethtool -r):
- struct niu_link_config: split advertising and autoneg
fields into active and target values (similar to speed
and duplex fields)
- mii_init_common(): rewrite function to actually apply
requested niu_link_config parameters instead of providing
default initialization
- link_status_1g(): move parsing of MII registers into
new link_status_mii() function (link_status_1g_rgmii()
could possibly use this new implementation too)
- introduce simple nway_reset method
- fix incorrect XMAC_CONFIG_MODE selection for 10Mbps case
Signed-off-by: Constantin Baranov <baranov@mercdev.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a typo in niu_determine_phy_disposition() which resulted in
phy_template_1g_copper being selected for 10G/copper configuration.
Signed-off-by: Constantin Baranov <baranov@mercdev.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Include the header file. If CONFIG_SFC_MTD is not defined
then the functions 'efx_mtd_remove' and 'efx_mtd_rename' are defined
'static inline' with an empty function body in the header file, but
the the whole file mtd.c is not built in this case.
Fix this sparse warnings:
drivers/net/sfc/mtd.c:204:6: warning: symbol 'efx_mtd_remove' was not declared. Should it be static?
drivers/net/sfc/mtd.c:221:6: warning: symbol 'efx_mtd_rename' was not declared. Should it be static?
drivers/net/sfc/mtd.c:230:5: warning: symbol 'efx_mtd_probe' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for adapters with a PCI id equal to 0x35.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phyid Can't be both TG3_PHY_OUI_1 and TG3_PHY_OUI_2 and TG3_PHY_OUI_3.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mib_counters_update() also restarts the timer.
So the timer is dequeued, the stats are read and then the timer is
enqueued again. This is "okay" unless someone unloads the module.
The locking here is also broken:
mib_counters_update() grabs just a simple spinlock. The only thing the
lock is good for is to protect the timer func against other callers
namely mv643xx_eth_stop() && mv643xx_eth_get_ethtool_stats(). That means
if the spinlock is taken via the ethtool path and than the timer kicks
in then the box will lock up.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If for some reason, read from card memory fails the console
get flooded with failure prints. This patch confines print
under printk_ratelimit().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse warnings (multiple instances)
warning: restricted degrades to integer
warning: cast to restricted type
warning: incorrect type in argument 3 (different signedness)
warning: context imbalance in 'netxen_nic_hw_write_wx_2M' - different
lock contexts for basic block
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NX3031 pci doorbells are not used. If unnecessary mapping
of doorbell space fails, pci probe bails out.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Remove the write-only field 'current_ring_status' completely.
Fix this sparse warnings:
drivers/net/tokenring/smctr.c:4410:52: warning: cast truncates bits from constant value (100 becomes 0)
drivers/net/tokenring/smctr.c:4415:52: warning: cast truncates bits from constant value (400 becomes 0)
drivers/net/tokenring/smctr.c:4420:52: warning: cast truncates bits from constant value (800 becomes 0)
drivers/net/tokenring/smctr.c:4425:52: warning: cast truncates bits from constant value (1000 becomes 0)
drivers/net/tokenring/smctr.c:4430:52: warning: cast truncates bits from constant value (2000 becomes 0)
drivers/net/tokenring/smctr.c:4435:52: warning: cast truncates bits from constant value (4000 becomes 0)
drivers/net/tokenring/smctr.c:4440:52: warning: cast truncates bits from constant value (8000 becomes 0)
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/wireless/prism54/isl_ioctl.c:2997:32: warning: incorrect type in argument 2 (different signedness)
drivers/net/wireless/prism54/oid_mgt.c:712:42: warning: incorrect type in argument 2 (different signedness)
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warnings:
drivers/net/wireless/ipw2x00/ipw2100.c:1930:43: warning: incorrect type in argument 4 (different signedness)
drivers/net/wireless/ipw2x00/ipw2100.c:1938:76: warning: incorrect type in argument 4 (different signedness)
drivers/net/wireless/ipw2x00/ipw2100.c:1946:67: warning: incorrect type in argument 4 (different signedness)
drivers/net/wireless/ipw2x00/ipw2100.c:1953:72: warning: incorrect type in argument 4 (different signedness)
drivers/net/wireless/ipw2x00/ipw2100.c:4071:73: warning: incorrect type in argument 4 (different signedness)
drivers/net/wireless/ipw2x00/ipw2100.c:4078:43: warning: incorrect type in argument 4 (different signedness)
drivers/net/wireless/ipw2x00/ipw2100.c:4084:67: warning: incorrect type in argument 4 (different signedness)
drivers/net/wireless/ipw2x00/ipw2100.c:7141:73: warning: incorrect type in argument 4 (different signedness)
drivers/net/wireless/ipw2x00/ipw2100.c:8317:48: warning: incorrect type in argument 4 (different signedness)
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this compilation warning:
drivers/net/wireless/b43/main.c: In function 'b43_print_fw_helptext':
drivers/net/wireless/b43/main.c:1971: warning: format not a string literal and no format arguments
drivers/net/wireless/b43/main.c:1973: warning: format not a string literal and no format arguments
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Make symbols static.
Fix this sparse warnings:
drivers/net/wireless/ath9k/eeprom.c:1343:5: warning: symbol 'ath9k_hw_4k_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:1372:19: warning: symbol 'eep_4k_ops' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2649:5: warning: symbol 'ath9k_hw_def_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2678:19: warning: symbol 'eep_def_ops' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warnings:
drivers/net/wireless/airo.c:2102:21: warning: incorrect type in initializer (different signedness)
drivers/net/wireless/airo.c:2126:21: warning: incorrect type in initializer (different signedness)
drivers/net/wireless/airo.c:2167:21: warning: incorrect type in initializer (different signedness)
drivers/net/wireless/airo.c:2191:21: warning: incorrect type in initializer (different signedness)
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact:
Move variable closer to usage resp.
remove redundant variables resp.
rename function scope variable.
Fix this sparse warnings:
drivers/net/wireless/airo.c:3840:29: warning: symbol 'i' shadows an earlier one
drivers/net/wireless/airo.c:3751:13: originally declared here
drivers/net/wireless/airo.c:3847:29: warning: symbol 'i' shadows an earlier one
drivers/net/wireless/airo.c:3751:13: originally declared here
drivers/net/wireless/airo.c:3861:21: warning: symbol 'i' shadows an earlier one
drivers/net/wireless/airo.c:3751:13: originally declared here
drivers/net/wireless/wavelan.c:43:13: warning: symbol 'irq' shadows an earlier one
drivers/net/wireless/wavelan.p.h:692:17: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Attribute function with __acquires(...) resp. __releases(...).
Fix this sparse warnings:
drivers/net/wireless/strip.c:955:21: warning: context imbalance in 'strip_seq_start' - wrong count at exit
drivers/net/wireless/strip.c:975:13: warning: context imbalance in 'strip_seq_stop' - unexpected unlock
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Rename function scope variable and while being at it fix some
coding style issues.
Fix this sparse warning:
drivers/net/wan/sbni.c:1526:14: warning: symbol 'num' shadows an earlier one
drivers/net/wan/sbni.c:160:13: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Use 'static const char[]' instead of 'static char[]'.
Fix this compilation warnings:
drivers/net/wan/lapbether.c: In function 'lapbeth_init_driver':
drivers/net/wan/lapbether.c:441: warning: format not a string literal and no format arguments
drivers/net/wan/z85230.c: In function 'z85230_init_driver':
drivers/net/wan/z85230.c:1782: warning: format not a string literal and no format arguments
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Make symbols static.
Fix this sparse warnings:
drivers/net/usb/hso.c:1249:6: warning: symbol 'hso_unthrottle_tasklet' was not declared. Should it be static?
drivers/net/usb/hso.c:1268:6: warning: symbol 'hso_unthrottle_workfunc' was not declared. Should it be static?
drivers/net/usb/hso.c:1466:5: warning: symbol 'tiocmget_submit_urb' was not declared. Should it be static?
drivers/net/usb/smsc95xx.c:62:5: warning: symbol 'turbo_mode' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Rename a local variable resp. remove a redundant variable and
while being at it use more unform loop constructs.
Fix this sparse warning:
drivers/net/tulip/de4x5.c:3944:13: warning: symbol 'i' shadows an earlier one
drivers/net/tulip/de4x5.c:3938:9: originally declared here
drivers/net/tulip/media.c:72:21: warning: symbol 'i' shadows an earlier one
drivers/net/tulip/media.c:54:13: originally declared here
drivers/net/tulip/media.c:134:21: warning: symbol 'i' shadows an earlier one
drivers/net/tulip/media.c:117:13: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Use 'static const char[]' instead of 'static char[]' and while
being at it add a KERN_INFO prefix.
Fix this warning:
drivers/net/tulip/de4x5.c: In function 'de4x5_hw_init':
drivers/net/tulip/de4x5.c:1268: warning: format not a string literal and no format arguments
drivers/net/tulip/winbond-840.c: In function 'w840_init':
drivers/net/tulip/winbond-840.c:1666: warning: format not a string literal and no format arguments
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Remove redundant variables.
Fix this sparse warnings:
drivers/net/tokenring/lanstreamer.c:619:21: warning: symbol 'i' shadows an earlier one
drivers/net/tokenring/lanstreamer.c:589:13: originally declared here
drivers/net/tokenring/madgemc.c:695:34: warning: symbol 'tp' shadows an earlier one
drivers/net/tokenring/madgemc.c:689:26: originally declared here
drivers/net/tokenring/olympic.c:702:21: warning: symbol 'i' shadows an earlier one
drivers/net/tokenring/olympic.c:440:13: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Use 'static const char[]' instead of 'static char[]'.
Fix this warnings:
drivers/net/tokenring/smctr.c:3644: warning: format not a string literal and no format arguments
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Move function declarations to header file.
Fix this sparse warnings:
drivers/net/skfp/cfm.c:146:6: warning: symbol 'all_selection_criteria' was not declared. Should it be static?
drivers/net/skfp/drvfbi.c:186:6: warning: symbol 'mac1_irq' was not declared. Should it be static?
drivers/net/skfp/drvfbi.c:284:6: warning: symbol 'read_address' was not declared. Should it be static?
drivers/net/skfp/drvfbi.c:323:6: warning: symbol 'init_board' was not declared. Should it be static?
drivers/net/skfp/fplustm.c:72:24: warning: symbol 'fddi_broadcast' was not declared. Should it be static?
drivers/net/skfp/fplustm.c:679:6: warning: symbol 'mac2_irq' was not declared. Should it be static?
drivers/net/skfp/fplustm.c:805:6: warning: symbol 'mac3_irq' was not declared. Should it be static?
drivers/net/skfp/fplustm.c:856:5: warning: symbol 'init_fplus' was not declared. Should it be static?
drivers/net/skfp/pcmplc.c:404:6: warning: symbol 'init_plc' was not declared. Should it be static?
drivers/net/skfp/pcmplc.c:1592:5: warning: symbol 'pcm_status_twisted' was not declared. Should it be static?
drivers/net/skfp/smtinit.c:68:5: warning: symbol 'init_smt' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Move variable declaration as close to their usage as possible.
Fix this sparse warning:
drivers/net/sfc/tenxpress.c:589:22: warning: symbol 'link_ok' shadows an earlier one
drivers/net/sfc/tenxpress.c:575:30: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Use 'static const char[]' instead of 'static char[]' and while
being at it prefix the message with KERN_INFO.
Fix this warnings:
drivers/net/pcmcia/axnet_cs.c:1716: warning: format not a string literal and no format arguments
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Make symbol static.
Fix this sparse warning:
drivers/net/ixgbe/ixgbe_82598.c:59:5: warning: symbol 'ixgbe_get_pcie_msix_count_82598' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Rename inner scrope variable.
Fix this sparse warning:
drivers/net/hamradio/yam.c:856:35: warning: symbol 'dev' shadows an earlier one
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Attribute functions with __acquires(...) resp. __releases(...).
Fix this sparse warnings:
drivers/net/hamradio/bpqether.c:387:13: warning: context imbalance in 'bpq_seq_start' - wrong count at exit
drivers/net/hamradio/bpqether.c:419:13: warning: context imbalance in 'bpq_seq_stop' - unexpected unlock
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Use 'static const char[]' instead of 'static char[]' and while
being at it fix an issue in 'mkiss_init_driver', where in case of an
error the status code was not passed to printk.
Fix this warnings:
drivers/net/hamradio/6pack.c: In function 'sixpack_init_driver':
drivers/net/hamradio/6pack.c:802: warning: format not a string literal and no format arguments
drivers/net/hamradio/bpqether.c: In function 'bpq_init_driver':
drivers/net/hamradio/bpqether.c:609: warning: format not a string literal and no format arguments
drivers/net/hamradio/mkiss.c: In function 'mkiss_init_driver':
drivers/net/hamradio/mkiss.c:988: warning: format not a string literal and no format arguments
drivers/net/hamradio/mkiss.c:991: warning: format not a string literal and no format arguments
drivers/net/hamradio/scc.c: In function 'scc_init_driver':
drivers/net/hamradio/scc.c:2109: warning: format not a string literal and no format arguments
drivers/net/hamradio/yam.c: In function 'yam_init_driver':
drivers/net/hamradio/yam.c:1094: warning: format not a string literal and no format arguments
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
