Select ARCH_HAS_UBSAN_SANITIZE_ALL in order to allow the user to
enable CONFIG_UBSAN_SANITIZE_ALL and instrument the entire kernel for
ubsan checks.
We exclude the VDSO from this because its build doesn't include the
__ubsan_handle_*() functions that the kernel proper defines in from
lib/ubsan.c, and the VDSO would have no sane way to report errors even
if it had definitions of these functions.
Signed-off-by: Hassan Naveed <hnaveed@wavecomp.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21179/
Cc: <linux-mips@linux-mips.org>
The Broadcom SiByte BCM1250, BCM1125, and BCM1125H SOCs have an onchip
DRAM controller that supports memory amounts of up to 16GiB, and due to
how the address decoder has been wired in the SOC any memory beyond 1GiB
is actually mapped starting from 4GiB physical up, that is beyond the
32-bit addressable limit[1]. Consequently if the maximum amount of
memory has been installed, then it will span up to 19GiB.
Many of the evaluation boards we support that are based on one of these
SOCs have their memory soldered and the amount present fits in the
32-bit address range. The BCM91250A SWARM board however has actual DIMM
slots and accepts, depending on the peripherals revision of the SOC, up
to 4GiB or 8GiB of memory in commercially available JEDEC modules[2].
I believe this is also the case with the BCM91250C2 LittleSur board.
This means that up to either 3GiB or 7GiB of memory requires 64-bit
addressing to access.
I believe the BCM91480B BigSur board, which has the BCM1480 SOC instead,
accepts at least as much memory, although I have no documentation or
actual hardware available to verify that.
Both systems have PCI slots installed for use by any PCI option boards,
including ones that only support 32-bit addressing (additionally the
32-bit PCI host bridge of the BCM1250, BCM1125, and BCM1125H SOCs limits
addressing to 32-bits), and there is no IOMMU available. Therefore for
PCI DMA to work in the presence of memory beyond enable swiotlb for the
affected systems.
All the other SOC onchip DMA devices use 40-bit addressing and therefore
can address the whole memory, so only enable swiotlb if PCI support and
support for DMA beyond 4GiB have been both enabled in the configuration
of the kernel.
This shows up as follows:
Broadcom SiByte BCM1250 B2 @ 800 MHz (SB1 rev 2)
Board type: SiByte BCM91250A (SWARM)
Determined physical RAM map:
memory: 000000000fe7fe00 @ 0000000000000000 (usable)
memory: 000000001ffffe00 @ 0000000080000000 (usable)
memory: 000000000ffffe00 @ 00000000c0000000 (usable)
memory: 0000000087fffe00 @ 0000000100000000 (usable)
software IO TLB: mapped [mem 0xcbffc000-0xcfffc000] (64MB)
in the bootstrap log and removes failures like these:
defxx 0000:02:00.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0
fddi0: Receive buffer allocation failed
fddi0: Adapter open failed!
IP-Config: Failed to open fddi0
defxx 0000:09:08.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0
fddi1: Receive buffer allocation failed
fddi1: Adapter open failed!
IP-Config: Failed to open fddi1
when memory beyond 4GiB is handed out to devices that can only do 32-bit
addressing.
This updates commit cce335ae47 ("[MIPS] 64-bit Sibyte kernels need
DMA32.").
References:
[1] "BCM1250/BCM1125/BCM1125H User Manual", Revision 1250_1125-UM100-R,
Broadcom Corporation, 21 Oct 2002, Section 3: "System Overview",
"Memory Map", pp. 34-38
[2] "BCM91250A User Manual", Revision 91250A-UM100-R, Broadcom
Corporation, 18 May 2004, Section 3: "Physical Description",
"Supported DRAM", p. 23
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
[paul.burton@mips.com: Remove GPL text from dma.c; SPDX tag covers it]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/21108/
References: cce335ae47 ("[MIPS] 64-bit Sibyte kernels need DMA32.")
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
The LittleSur board is marked for high memory support and therefore
clearly must provide a way to have enough memory installed for some to
be present outside the low 4GiB physical address range. With the memory
map of the BCM1250 SOC it has been built around it means over 1GiB of
actual DRAM, as only the first 1GiB is mapped in the low 4GiB physical
address range[1].
Complement commit cce335ae47 ("[MIPS] 64-bit Sibyte kernels need
DMA32.") then and also enable ZONE_DMA32 for LittleSur.
References:
[1] "BCM1250/BCM1125/BCM1125H User Manual", Revision 1250_1125-UM100-R,
Broadcom Corporation, 21 Oct 2002, Section 3: "System Overview",
"Memory Map", pp. 34-38
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/21107/
Fixes: cce335ae47 ("[MIPS] 64-bit Sibyte kernels need DMA32.")
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Select CONFIG_CPU_NO_EFFICIENT_FFS via Kconfig when the kernel is
configured for a pre-MIPS32r1 CPU, rather than defining its equivalent
in asm/cpu-features.h based upon overrides of cpu_has_mips* macros.
The latter only works if a platform has an cpu-feature-overrides.h
header which defines cpu_has_mips* macros, which are not generally
needed. There are many cases where we know that the target ISA for a
kernel build is MIPS32r1 or later & thus includes the CLZ instruction,
without requiring any overrides from the platform. Using Kconfig allows
us to take those into account, and more naturally make a decision about
instruction support using information about the target ISA.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21045/
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Zhaoxiu Zeng <zhaoxiu.zeng@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Allow the user to configure the kernel to omit support for floating
point, by setting CONFIG_MIPS_FP_SUPPORT=n. In an attempt to avoid
problems for users who don't understand the impact of this, only expose
the option when CONFIG_EXPERT=y.
When CONFIG_MIPS_FP_SUPPORT=n all support for FPU hardware, FPU
emulation & FP context will be removed from the kernel. If a userland
program attempts to execute a floating point instruction it will receive
a SIGILL.
Setting CONFIG_MIPS_FP_SUPPORT=n shaves around 112KB from a
64r6el_defconfig build using GCC 8.1.0.
This also helps prepare us for supporting the nanoMIPS ISA, for which
floating point support has not been finalized.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21014/
Cc: linux-mips@linux-mips.org
When CONFIG_MIPS_FP_SUPPORT=n we don't support floating point, so we can
avoid needless checks of ELF headers specifying the FP ABI or NaN
encoding to use. Deselect CONFIG_ARCH_BINFMT_ELF_STATE in this case to
avoid the need for our arch_elf_pt_proc() & arch_check_elf() functions,
and stub out the mips_set_personality_nan() & mips_set_personality_fp()
functions such that SET_PERSONALITY() doesn't need to worry about any of
this.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21011/
Cc: linux-mips@linux-mips.org
Introduce a Kconfig variable that will indicate whether to include
support for floating point in the kernel. For now this is always
enabled, and will be made configurable in a later patch.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21016/
Cc: linux-mips@linux-mips.org
Introduce a CONFIG_CPU_R2300_FPU Kconfig symbol mirroring the existing
CONFIG_CPU_R4K_FPU, and use it to determine whether to build r4k_fpu.S.
This removes the duplicate R3000 & TX39XX cases in
arch/mips/kernel/Makefile and prepares us for the possibility of
disabling FP support later.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21004/
Cc: linux-mips@linux-mips.org
From MIPSr6 onwards FP64 support is mandatory, and so
CONFIG_MIPS_O32_FP64_SUPPORT is always selected for configurations which
support O32 binaries. Hide the useless unchangeable prompt in these
cases.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21019/
Cc: linux-mips@linux-mips.org
Allows the users of ptrace to access memory mapped by the ptraced process
using the same cache coherency attributes as the original process.
For example while using gdb with ioremap_prot() incorporated, both gdb and
the process being traced will have same cache coherency attributes.
Signed-off-by: Hassan Naveed <hnaveed@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20955/
Cc: <linux-mips@linux-mips.org>
All architecures use memblock for early memory management. There is no need
for the CONFIG_HAVE_MEMBLOCK configuration option.
[rppt@linux.vnet.ibm.com: of/fdt: fixup #ifdefs]
Link: http://lkml.kernel.org/r/20180919103457.GA20545@rapoport-lnx
[rppt@linux.vnet.ibm.com: csky: fixups after bootmem removal]
Link: http://lkml.kernel.org/r/20180926112744.GC4628@rapoport-lnx
[rppt@linux.vnet.ibm.com: remove stale #else and the code it protects]
Link: http://lkml.kernel.org/r/1538067825-24835-1-git-send-email-rppt@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1536927045-23536-4-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All achitectures select NO_BOOTMEM which essentially becomes 'Y' for any
kernel configuration and therefore it can be removed.
[alexander.h.duyck@linux.intel.com: remove now defunct NO_BOOTMEM from depends list for deferred init]
Link: http://lkml.kernel.org/r/20180925201814.3576.15105.stgit@localhost.localdomain
Link: http://lkml.kernel.org/r/1536927045-23536-3-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Subsystem:
- non devm managed registration is now removed from the driver API.
- all the unnecessary rtc_valid_tm() calls have been removed
Drivers:
- abx80X: watchdog support
- cmos: fix non ACPI support
- sc27xx: fix alarm support
- Remove a possible sysfs race condition for ab8500, ds1307, ds1685, isl1208
- Fix a possible race condition where an irq handler may be called before the
rtc_device struct is allocated for mt6397, pl030, menelaus, armada38x
-----BEGIN PGP SIGNATURE-----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=5JM5
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"This cycle, there were mostly non urgent fixes in drivers. I also
finally unexported the non managed registration.
Subsystem:
- non devm managed registration is now removed from the driver API
- all the unnecessary rtc_valid_tm() calls have been removed
Drivers:
- abx80X: watchdog support
- cmos: fix non ACPI support
- sc27xx: fix alarm support
- Remove a possible sysfs race condition for ab8500, ds1307, ds1685,
isl1208
- Fix a possible race condition where an irq handler may be called
before the rtc_device struct is allocated for mt6397, pl030,
menelaus, armada38x"
* tag 'rtc-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (54 commits)
rtc: sc27xx: Always read normal alarm when registering RTC device
rtc: sc27xx: Add check to see if need to enable the alarm interrupt
rtc: sc27xx: Remove interrupts disable and clear in probe()
rtc: sc27xx: Clear SPG value update interrupt status
rtc: sc27xx: Set wakeup capability before registering rtc device
rtc: s35390a: Change buf's type to u8 in s35390a_init
rtc: ds1307: fix ds1339 wakealarm support
rtc: ds1685: simplify getting .driver_data
rtc: m41t80: mark expected switch fall-through
rtc: tegra: Propagate errors from platform_get_irq()
rtc: cmos: Remove the `use_acpi_alarm' module parameter for !ACPI
rtc: cmos: Fix non-ACPI undefined reference to `hpet_rtc_interrupt'
rtc: mv: let the core handle invalid alarms
rtc: vr41xx: switch to rtc_time64_to_tm/rtc_tm_to_time64
rtc: ab8500: remove useless check
rtc: ab8500: let the core handle range
rtc: ab8500: use rtc_add_group
rtc: rs5c348: report error when time is invalid
rtc: rs5c348: remove forward declaration
rtc: rs5c348: remove useless label
...
- kexec support for the generic MIPS platform when running on a CPU
including the MIPS Coherence Manager & related hardware.
- Improvements to the definition of memory barriers used around MMIO
accesses, and fixes in their use.
- Switch to CONFIG_NO_BOOTMEM from Mike Rapoport, finally dropping
reliance on the old bootmem code.
- A number of fixes & improvements for Loongson 3 systems.
- DT & config updates for the Microsemi Ocelot platform.
- Workaround to enable USB power on the Netgear WNDR3400v3.
- Various cleanups & fixes.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW9NfwRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN1LNgD9Hy73DkYnnYeLNLcCe+5QMCr+NO2C
kwIs7kAI40X+/LQA/RgCcg6z4rUSH38hfNEobD6VXva7QiFhiYcJj5rCFH8O
=nDQg
-----END PGP SIGNATURE-----
Merge tag 'mips_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
- kexec support for the generic MIPS platform when running on a CPU
including the MIPS Coherence Manager & related hardware.
- Improvements to the definition of memory barriers used around MMIO
accesses, and fixes in their use.
- Switch to CONFIG_NO_BOOTMEM from Mike Rapoport, finally dropping
reliance on the old bootmem code.
- A number of fixes & improvements for Loongson 3 systems.
- DT & config updates for the Microsemi Ocelot platform.
- Workaround to enable USB power on the Netgear WNDR3400v3.
- Various cleanups & fixes.
* tag 'mips_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (51 commits)
MIPS: Cleanup DSP ASE detection
MIPS: dts: Change upper case to lower case
MIPS: generic: Add Network, SPI and I2C to ocelot_defconfig
MIPS: Loongson-3: Fix BRIDGE irq delivery problem
MIPS: Loongson-3: Fix CPU UART irq delivery problem
MIPS: Remove unused PREF, PREFE & PREFX macros
MIPS: lib: Use kernel_pref & user_pref in memcpy()
MIPS: Remove unused CAT macro
MIPS: Add kernel_pref & user_pref helpers
MIPS: Remove unused TTABLE macro
MIPS: Remove unused PIC macros
MIPS: Remove unused MOVN & MOVZ macros
MIPS: Provide actually relaxed MMIO accessors
MIPS: Enforce strong ordering for MMIO accessors
MIPS: Correct `mmiowb' barrier for `wbflush' platforms
MIPS: Define MMIO ordering barriers
MIPS: mscc: add PCB120 to the ocelot fitImage
MIPS: mscc: add DT for Ocelot PCB120
MIPS: memset: Limit excessive `noreorder' assembly mode use
MIPS: memset: Fix CPU_DADDI_WORKAROUNDS `small_fixup' regression
...
MIPSR6 CPUs do not support unaligned load/store instructions
(LWL, LWR, SWL, SWR and LDL, LDR, SDL, SDR for 64bit).
Currently the MIPS tree has some special cases to avoid these
instructions, and the code is testing for !CONFIG_CPU_MIPSR6.
This patch declares a new Kconfig variable:
CONFIG_CPU_HAS_LOAD_STORE_LR.
This variable indicates that the CPU supports these instructions.
Then, the patch does the following:
- Carefully selects this option on all CPUs except MIPSR6.
- Switches all the special cases to test for the new variable,
and inverts the logic:
'#ifndef CONFIG_CPU_MIPSR6' turns into
'#ifdef CONFIG_CPU_HAS_LOAD_STORE_LR'
and vice-versa.
Also, when this variable is NOT selected (e.g. MIPSR6),
CONFIG_GENERIC_CSUM will default to 'y', to compile generic
C checksum code (instead of special assembly code that uses the
unsupported instructions).
This commit should not affect any existing CPU, and is required
for future Lexra CPU support, that misses these instructions too.
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20808/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Out-of-tree platforms may not be based on Generic as shown in customer
communication. Share the prepare method with all using UHI boot protocol,
and put into machine_kexec.c.
The benefit is that, when having kexec_args related problems, developers
will naturally look into machine_kexec.c, where "CONFIG_UHI_BOOT" will be
found, prompting them to add "select UHI_BOOT" to the platform Kconfig. It
would otherwise require a lot debugging or online searching to be aware
that the solution is in Generic code.
Tested-by: Rachel Mozes <rachel.mozes@intel.com>
Reported-by: Rachel Mozes <rachel.mozes@intel.com>
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20569/
Cc: pburton@wavecomp.com
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
The only functional differences (modulo a few missing fixes in the arch
code) is that architectures without coherent caches need a hook to
convert a virtual or dma address into a pfn, given that we don't have
the kernel linear mapping available for the otherwise easy virt_to_page
call. As a side effect we can support mmap of the per-device coherent
area even on architectures not providing the callback, and we make
previous dangerous default methods dma_common_mmap actually save for
non-coherent architectures by rejecting it without the right helper.
In addition to that we need a hook so that some architectures can
override the protection bits when mmaping a dma coherent allocations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS parts
All the cache maintainance is already stubbed out when not enabled,
but merging the two allows us to nicely handle the case where
cache maintainance is required for some devices, but not others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS parts
Various architectures support both coherent and non-coherent dma on a
per-device basis. Move the dma_noncoherent flag from the mips archdata
field to struct device proper to prepare the infrastructure for reuse on
other architectures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While both option select a form of conditional dma coherence they don't
actually share any code in the implementation, so untangle them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com>
MIPS already has memblock support and all the memory is already registered
with it.
This patch replaces bootmem memory reservations with memblock ones and
removes the bootmem initialization.
Since memblock allocates memory in top-down mode, we ensure that memblock
limit is max_low_pfn to prevent allocations from the high memory.
To have the exceptions base in the lower 512M of the physical memory, its
allocation in arch/mips/kernel/traps.c::traps_init() is using bottom-up
mode.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20560/
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-mm@kvack.org
Cc: linux-kernel@vger.kernel.org
The old rtc driver is getting in the way of some compat_ioctl
simplification. Looking up the loongson64 git history, it seems
that everyone uses the more modern but compatible RTC_CMOS driver
anyway, so let's remove the special case for loongson64.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
MIPS has a copy of lib/iomap.c with minor alterations, none of which are
necessary given appropriate definitions of PIO_OFFSET, PIO_MASK &
PIO_RESERVED. Provide such definitions, select GENERIC_IOMAP & remove
arch/mips/lib/iomap.c to cut back on the needless duplication.
The one change this does make is to our mmio_{in,out}s[bwl] functions,
which began to deviate from their generic counterparts with commit
0845bb721e ("MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO"). I
suspect that this commit was incorrect, and that the SEAD-3 platform
should have instead selected CONFIG_SWAP_IO_SPACE. Since the SEAD-3
platform code is now gone & the board is instead supported by the
generic platform (CONFIG_MIPS_GENERIC) which selects
CONFIG_SWAP_IO_SPACE anyway, this shouldn't be a problem any more.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20342/
Cc: linux-mips@linux-mips.org
- Fix microMIPS build failures by adding a .insn directive to the
barrier_before_unreachable() asm statement in order to convince the
toolchain that the asm statement is a valid branch target rather
than a bogus attempt to switch ISA.
- Clean up our declarations of TLB functions that we overwrite with
generated code in order to prevent the compiler making assumptions
about alignment that cause microMIPS kernels built with GCC 7 &
above to die early during boot.
- Fix up a regression for MIPS32 kernels which slipped into the main
MIPS pull for 4.19, causing CONFIG_32BIT=y kernels to contain
inappropriate MIPS64 instructions.
- Extend our existing workaround for MIPSr6 builds that end up using
the __multi3 intrinsic to GCC 7 & below, rather than just GCC 7.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW37wVhUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN18iAD/ZO02rgkTgMG7NvZMtbOwflxe1aVz
YpAQzcOSz+CBxgUA/30ZwZm37hgMi3YWOJMSfmbuWKsYi+/vkcjwlfai7UUF
=oJFy
-----END PGP SIGNATURE-----
Merge tag 'mips_4.19_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
- Fix microMIPS build failures by adding a .insn directive to the
barrier_before_unreachable() asm statement in order to convince the
toolchain that the asm statement is a valid branch target rather
than a bogus attempt to switch ISA.
- Clean up our declarations of TLB functions that we overwrite with
generated code in order to prevent the compiler making assumptions
about alignment that cause microMIPS kernels built with GCC 7 &
above to die early during boot.
- Fix up a regression for MIPS32 kernels which slipped into the main
MIPS pull for 4.19, causing CONFIG_32BIT=y kernels to contain
inappropriate MIPS64 instructions.
- Extend our existing workaround for MIPSr6 builds that end up using
the __multi3 intrinsic to GCC 7 & below, rather than just GCC 7.
* tag 'mips_4.19_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: lib: Provide MIPS64r6 __multi3() for GCC < 7
MIPS: Workaround GCC __builtin_unreachable reordering bug
compiler.h: Allow arch-specific asm/compiler.h
MIPS: Avoid move psuedo-instruction whilst using MIPS_ISA_LEVEL
MIPS: Consistently declare TLB functions
MIPS: Export tlbmiss_handler_setup_pgd near its definition
Some versions of GCC for the MIPS architecture suffer from a bug which
can lead to instructions from beyond an unreachable statement being
incorrectly reordered into earlier branch delay slots if the unreachable
statement is the only content of a case in a switch statement. This can
lead to seemingly random behaviour, such as invalid memory accesses from
incorrectly reordered loads or stores, and link failures on microMIPS
builds.
See this potential GCC fix for details:
https://gcc.gnu.org/ml/gcc-patches/2015-09/msg00360.html
Runtime problems resulting from this bug were initially observed using a
maltasmvp_defconfig v4.4 kernel built using GCC 4.9.2 (from a Codescape
SDK 2015.06-05 toolchain), with the result being an address exception
taken after log messages about the L1 caches (during probe of the L2
cache):
Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
VPE topology {2,2} total 4
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, PIPT, no aliases, linesize 32 bytes
<AdEL exception here>
This is early enough that the kernel exception vectors are not in use,
so any further output depends upon the bootloader. This is reproducible
in QEMU where no further output occurs - ie. the system hangs here.
Given the nature of the bug it may potentially be hit with differing
symptoms. The bug is known to affect GCC versions as recent as 7.3, and
it is unclear whether GCC 8 fixed it or just happens not to encounter
the bug in the testcase found at the link above due to differing
optimizations.
This bug can be worked around by placing a volatile asm statement, which
GCC is prevented from reordering past, prior to the
__builtin_unreachable call.
That was actually done already for other reasons by commit 173a3efd3e
("bug.h: work around GCC PR82365 in BUG()"), but creates problems for
microMIPS builds due to the lack of a .insn directive. The microMIPS ISA
allows for interlinking with regular MIPS32 code by repurposing bit 0 of
the program counter as an ISA mode bit. To switch modes one changes the
value of this bit in the PC. However typical branch instructions encode
their offsets as multiples of 2-byte instruction halfwords, which means
they cannot change ISA mode - this must be done using either an indirect
branch (a jump-register in MIPS terminology) or a dedicated jalx
instruction. In order to ensure that regular branches don't attempt to
target code in a different ISA which they can't actually switch to, the
linker will check that branch targets are code in the same ISA as the
branch.
Unfortunately our empty asm volatile statements don't qualify as code,
and the link for microMIPS builds fails with errors such as:
arch/mips/mm/dma-default.s:3265: Error: branch to a symbol in another ISA mode
arch/mips/mm/dma-default.s:5027: Error: branch to a symbol in another ISA mode
Resolve this by adding a .insn directive within the asm statement which
declares that what comes next is code. This may or may not be true,
since we don't really know what comes next, but as this code is in an
unreachable path anyway that doesn't matter since we won't execute it.
We do this in asm/compiler.h & select CONFIG_HAVE_ARCH_COMPILER_H in
order to have this included by linux/compiler_types.h after
linux/compiler-gcc.h. This will result in asm/compiler.h being included
in all C compilations via the -include linux/compiler_types.h argument
in c_flags, which should be harmless.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 173a3efd3e ("bug.h: work around GCC PR82365 in BUG()")
Patchwork: https://patchwork.linux-mips.org/patch/20270/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Move the source statements of arch-independent Kconfig files instead of
duplicating the includes in every arch/$(SRCARCH)/Kconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gsQJ
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig consolidation from Masahiro Yamada:
"Consolidation of Kconfig files by Christoph Hellwig.
Move the source statements of arch-independent Kconfig files instead
of duplicating the includes in every arch/$(SRCARCH)/Kconfig"
* tag 'kconfig-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: add a Memory Management options" menu
kconfig: move the "Executable file formats" menu to fs/Kconfig.binfmt
kconfig: use a menu in arch/Kconfig to reduce clutter
kconfig: include kernel/Kconfig.preempt from init/Kconfig
Kconfig: consolidate the "Kernel hacking" menu
kconfig: include common Kconfig files from top-level Kconfig
kconfig: remove duplicate SWAP symbol defintions
um: create a proper drivers Kconfig
um: cleanup Kconfig files
um: stop abusing KBUILD_KCONFIG
Almost all architectures include it. Add a ARCH_NO_PREEMPT symbol to
disable preempt support for alpha, hexagon, non-coldfire m68k and
user mode Linux.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move the source of lib/Kconfig.debug and arch/$(ARCH)/Kconfig.debug to
the top-level Kconfig. For two architectures that means moving their
arch-specific symbols in that menu into a new arch Kconfig.debug file,
and for a few more creating a dummy file so that we can include it
unconditionally.
Also move the actual 'Kernel hacking' menu to lib/Kconfig.debug, where
it belongs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Instead of duplicating the source statements in every architecture just
do it once in the toplevel Kconfig file.
Note that with this the inclusion of arch/$(SRCARCH/Kconfig moves out of
the top-level Kconfig into arch/Kconfig so that don't violate ordering
constraits while keeping a sensible menu structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
LS232 (Loonson 2-issue 32-bit, also called GS232 (Godson 2-issue 32-bit))
is the CPU core (microarchitecture) of Loongson 1A/1B/1C.
According to "LS232 用户手册 (LS232 User Manual)", LS232 implements the
MIPS32 Release 1 instruction set, and part of the MIPS32 Release 2
instruction set.
In the manual, LS232 implements all of the MIPS32R2 instruction set
except the FPU instructions, and LS232 also implements 5 FPU
instructions of the MIPS32R2 instruction set: CEIL.L.fmt, CVT.L.fmt,
FLOOR.L.fmt, TRUNC.L.fmt, and ROUND.L.fmt.
But a bug of the DI instruction has been found during tests, the DI
instruction can not disable interrupts in arch_local_irq_disable() with
CONFIG_PREEMPT_NONE=y and CFLAGS='-mno-branch-likely' in some cases.
[paul.burton@mips.com:
- Remove the _MIPS_ISA redefinition to match the change made for the
generic MIPSr1 CPUs by commit 344ebf0994 ("MIPS: Always use
-march=<arch>, not -<arch> shortcuts").]
Signed-off-by: 谢致邦 (XIE Zhibang) <Yeking@Red54.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/16155/
Cc: linux-mips@linux-mips.org
Cc: ralf@linux-mips.org
Enable CONFIG_MIPS_AUTO_PFN_OFFSET for the generic platform, allowing
it to avoid wasted book-keeping for pages with addresses lower than the
physical base address of memory.
This has a minimal impact on kernel text size, with 64r6el_defconfig
gaining 0.1% in size as reported by bloat-o-meter:
add/remove: 4/1 grow/shrink: 345/13 up/down: 9017/-392 (8625)
Function old new delta
pcpu_setup_first_chunk 1444 1780 +336
pcpu_alloc_first_chunk 864 1136 +272
start_kernel 1064 1288 +224
initcall_blacklist 224 372 +148
try_fill_recv 2088 2184 +96
...
Total: Before=8457273, After=8465898, chg +0.10%
The gain for systems with large offsets to physical memory & the ability
to continue using generic kernels on such systems seems well worth this
small cost.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Suggested-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/20049/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
On systems where physical memory begins at a non-zero address, defining
PHYS_OFFSET (which influences ARCH_PFN_OFFSET) can save us time & memory
by avoiding book-keeping for pages from address zero to the start of
memory.
Some MIPS platforms already make use of this, but with the definition of
PHYS_OFFSET being compile-time constant it hasn't been possible to
enable this optimization for a kernel which may run on systems with
varying physical memory base addresses.
Introduce a new Kconfig option CONFIG_MIPS_AUTO_PFN_OFFSET which, when
enabled, makes ARCH_PFN_OFFSET a variable & detects it from the boot
memory map (which for example may have been populated from DT). The
relationship with PHYS_OFFSET is reversed, with PHYS_OFFSET now being
based on ARCH_PFN_OFFSET. This is because ARCH_PFN_OFFSET is used far
more often, so avoiding the need for runtime calculation gives us a
smaller impact on kernel text size (0.1% rather than 0.15% for
64r6el_defconfig).
Signed-off-by: Paul Burton <paul.burton@mips.com>
Suggested-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/20048/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
The pinmux on QCA SoCs is controlled by a single register. The
"pinctrl-single" driver can be used but requires the target
to select PINCTRL.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19909/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
All Octeons starting with Octeon II have RAPIDIO controller which
can function even with PCI disabled.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Alexandre Bounine <alex.bou9@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19988/
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Introduce the same option as PPC and ARM already have because
RAPIDIO can function in the absence of PCI.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Alexandre Bounine <alex.bou9@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19987/
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Remove the platform code used to power down the system, instead relying
upon the new PIIX4 poweroff driver. This reduces the amount of platform
code required for the Malta board in preparation for allowing it to be
part of a more generic kernel.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/14282/
Provide phys_to_dma/dma_to_phys helpers, and the special
arch_sync_dma_for_cpu_all hook, everything else is generic
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19550/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
Provide phys_to_dma/dma_to_phys helpers only if PCI support is
enabled, everything else is generic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19547/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
Convert everything not overriding dma-coherence.h to the generic
noncoherent ops. The new dma-noncoherent.c file duplicates a lot of
the code in dma-default.c, but that file will be gone by the end of
this series.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19544/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
IP27 is coherent and has a reasonably direct mapping, just with a little
per-bus offset added into the dma address.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19542/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
Switch the simple cache coherent architectures that don't require any
DMA address translation to dma_direct_ops.
We'll soon use at least parts of the direct DMA ops implementation for
all platforms, so select the symbol globally.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19540/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
Only loongson-3 is DMA coherent and uses swiotlb. So move the dma
address translations stubs directly to the loongson-3 code, and remove
a few Kconfig indirections.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19539/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
Octeon and loonson64 already don't use it at all, and we're going to
migrate more plaforms away from it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19536/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
We can just check for !CONFIG_DMA_NONCOHERENT instead and simplify things
a lot.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19530/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
Implement support for restartable sequences on MIPS, which requires 3
simple things:
- Call rseq_handle_notify_resume() on return to userspace if
TIF_NOTIFY_RESUME is set.
- Call rseq_signal_deliver() to fixup the pre-signal stack frame when
a signal is delivered whilst executing a restartable sequence
critical section.
- Select CONFIG_HAVE_RSEQ.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/19523/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
