This allows for specific identification of beacons in the debugfs
frame stream.
Preparation for later differences between dumped TX frames and dumped
beacons.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The handling of tx descriptors for beacons can be simplified by updating
write_tx_desc implementations of each driver to write directly to the
queue entry descriptor instead of to a provided memory area.
This is also a preparation for further clean ups where descriptors are
properly reserved in the skb instead of fiddling with the skb data
pointer.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a little bit of restructuring it isn't necessary to have special
cases in rt2x00queue_write_tx_descriptor for writing the descriptor
for beacons.
Simply split off the kicking of the TX queue to a separate function
with is only called for non-beacons.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation to fix rt2800 beaconing.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All of the driver's kick_tx_queue callback functions treat the TX queue
for beacons in a special manner.
Clean this up by integrating the kicking of the beacon queue into the
write_beacon callback function, and let the generic code no longer call
the kick_tx_queue callback function when updating the beacon.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And use it consistently in the chipset drivers.
Preparation for further clean ups.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend the write_tx_data callback with a txdesc parameter to allow
access to the tx desciptor while preparing the tx data.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use rt2x00dev->ops->extra_tx_headroom, not rt2x00dev->hw->extra_tx_headroom
in the tx code, as the later may include other headroom not to be used in
the chipset driver.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that frames without payload are properly trimmed in
rt2x00queue_insert_l2pad.
This should fix the bug reported by Benoit Papillault in:
http://marc.info/?l=linux-wireless&m=125974773006734&w=2
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the rt2x00queue_insert_l2pad function by handling the alignment
operations one by one. Do not special case special circumstances.
Basically first perform header alignment, and then perform payload alignment
(if any payload does exist). This results in a properly aligned skb.
The end result is better readable code, with better results, as now L2 padding
is inserted only when a payload is actually present in the frame.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the improved L2 padding code, this flag is no longer necessary, as the
rt2x00queue_remove_l2pad is capable of detecting by itself if L2 padding is
applied.
For received frames the RX descriptor flag is still being checked.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a couple of more bugs in the L2 padding code:
1. Compute the amount of L2 padding correctly (in 3 places).
2. Trim the skb correctly when the L2 padding has been applied.
Also introduce a central macro the compute the L2 padding size.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not include timestamp for a frame that has been injected
through a monitor interface.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The padding is to be added between header and payload for the only header need
padding case.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While reviewing the l2pad function to align both the header and the payload
on a DMA-capable boundary a bug was discovered where the payload would not
be properly aligned. The header_align value was used where the payload_align
value should have been used.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now all frames mac80211 hands to the driver
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to
request TX status. This isn't really necessary, only
the injected frames need TX status (the latter for
hostapd) so move setting this flag.
The rate control algorithms also need TX status, but
they don't require it.
Also, rt2x00 uses that bit for its own purposes and
seems to require it being set for all frames, but
that can be fixed in rt2x00.
This doesn't really change anything for any drivers
but in the future drivers using hw-rate control may
opt to not report TX status for frames that don't
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As mentioned on the linux-wireless mailing list, the current copyright
statements in the rt2x00 are meaningless, as the rt2x00 project is
not even a formal legal entity. Therefore it is better to replace
the existing copyright statements with copyright statements for the
people that actually wrote the code.
Note: Updated to the best of my knowledge with respect to who
contributed considerable amounts of code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old function rt2x00queue_payload_align() handled
both adding and removing L2 padding and some basic
frame alignment. The entire function was being abused
because it had multiple functions and the header length
argument was somtimes used to align the header instead
of the payload.
Additionally there was a bug when inserting L2 padding
that only the payload was aligned but not the header. This
happens when the header wasn't aligned properly by mac80211,
but rt2x00lib only moves the payload.
A secondary problem was that when removing L2 padding during
TXdone or RX the skb wasn't resized to the proper size.
Split the function into seperate functions each handling
its task as it should.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch "Implement set_tim callback for all drivers" can cause kernel
oops in rt73usb_write_beacon. The oops is caused by one of the following
race conditions:
* In case of two near calls to set_tim: rt2x00lib_beacondone_iter is
cleaning the beacon skb, whereas rt73usb_write_beacon is still using it.
* In case of two near updates of beacon: first as the result of set_tim
and second as the result of a call from an application (e.g. hostapd).
This patch fixes the race condition by rearranging the update logic and
guarding rt2x00_intf->beacon->skb with a mutex.
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware require the ieee80211 header to be aligned to a
4-byte boundary before mapping it to the DMA. Otherwise some
frames (like beacons) will not be send out correctly by the
device.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the IEEE80211_TX_CTL_MORE_FRAMES flag to help determining
if the DMA queue should be kicked. At the moment this is combined
with the ieee80211_has_morefrags() but we might remove that later.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend rt2x00lib capabilities to support 802.11n,
it still lacks aggregation support, but that can
be added in the future.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware require L2 padding between header and payload
because both must be aligned to a 4-byte boundary. This hardware
also is easier during the RX path since we no longer need to
move the entire payload but rather only the header to remove
the padding (mac80211 only wants the payload to be 4-byte aligned).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By placing the iv_len into the tx descriptor data and
by passing this data to the crypto IV handlers we can
save multiple calls to ieee80211_get_hdrlen_from_skb()
and some if-statements when copying/removing the IV data
from the outgoing frame.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
provide rt2x00lib the possibility to kill a particular TX queue.
This can be useful when disabling the radio, but more importantly
will allow beaconing to be disabled when mac80211 requests this
(during scanning for example)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag ENTRY_TXD_OFDM_RATE isn't flexible enough
to indicate which rate modulation should be used for
a frame. This will become a problem when 11n support
is added.
Remove the flag and replace it with an enum value which
can better indicate the exact rate modulation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some functions have grown rapidly in size over the last time,
some of those functions (like the rt2x00queue_create_tx_descriptor)
will further increase in size soon, so it is best to start cutting
it into logical pieces.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_CRYPTO_COPY_IV is a bad name since it is part
of the driver requirements instead of a configuration option.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 provides 2 structures to handle bitrates, namely
ieee80211_rate and ieee80211_tx_rate. To determine the short preamble
mode for an outgoing frame, the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE
must be checked on ieee80211_tx_rate and not ieee80211_rate (which rt2x00 did).
This fixes a regression which was triggered in 2.6.29-rcX as reported by Chris Clayton.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-By: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The short preamble mode was not correctly detected during TX,
rt2x00 used the rate->hw_value_short field but mac80211 is not
using this field that way.
Instead the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE should be
used to determine if the frame should be send out using
short preamble or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all code which determines the right TX descriptor
fields specific to crypto support into rt2x00crypto.c.
This makes the code in rt2x00queue more simpler and
better concentrates all crypto code into a single location.
With this we can also remove some ifdefs in rt2x00queue.c
since the code inside the ifdef is either very small, or
only calling empty functions (see empty function definitions
in rt2x00lib.h).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb supports hardware encryption.
rt2500usb supports up to 4 shared and pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store retry limit values in the rt2x00dev structure.
This allows the removal of the FIXME where we assumed
the long retry is only used when working with RTS frames.
Instead we should check the current retry limit values
and decide if the required retry count for this frame
is a long or short retry.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback function write_tx_data() can only fail
when our ENTRY_OWNER_DEVICE_DATA flag on a queue entry
failed to determine the entry was not available and
it is in fact still owned by the hardware.
This means that if that function fails the queue
must be stopped in mac80211.
When rt2x00queue_get_queue() returns NULL in the TX
path, it means mac80211 has passed us an invalid queue,
although this should be impossible, it shouldn't hurt
if we send mac80211 a signal to stop the queue either.
Both issues can simply be resolved by removing their
manual failure handler and making them use the failure path
provided in rt2x00mac_tx().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can optimize get_duration and get_duration_res
by making them a macro. They are really simple
calculation handlers so this doesn't matter much.
Often (especially in rt2400pci and rt2500pci,
the arguments are hardcoded, and the result value
is passed into other hardcoded values.
By making the functions a macro GCC can
optimize the entire thing much better.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge the callback functions init_txentry() and
init_rxentry(). This makes life in rt2x00lib a
lot simpler and we can cleanup several functions.
rt2x00pci contained "fake" FIELD definitions for
descriptor words. This is not flexible since it
assumes the driver will always have the same field
to indicate if a driver is available or not.
This should be dependent on the driver, and we
should add a callback function for this.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few changes to reduce checkpatch.pl errors in the rt2x00 driver. For
the most part, I only fixed cosmetic things, and left the actual 'code
flow' untouched (hopefully)!
Diff is against wireless-testing HEAD.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw_key pointer is used (and obviously NULL) after skb->cb is
memset to 0. This patch grabs the iv_len before the memset call.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free up 2 bytes in skb->cb to be used for multi-rate retry later.
Move iv_len and icv_len initialization into key alloc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, virtual interface pointers passed to drivers might be
from monitor interfaces and as such completely uninitialised
because we do not tell the driver about monitor interfaces when
those are created. Instead of passing them, we should therefore
indicate to the driver that there is no information; do that by
passing a NULL value and adjust drivers to cope with it.
As a result, some mac80211 API functions also need to cope with
a NULL vif pointer so drivers can still call them unconditionally.
Also, when injecting frames we really don't want to pass NULL all
the time, if we know we are the source address of a frame and have
a local interface for that address, we can to use that interface.
This also helps with processing the frame correctly for that
interface which will help the 802.11w implementation. It's not
entirely correct for VLANs or WDS interfaces because there the MAC
address isn't unique, but it's already a lot better than what we
do now.
Finally, when injecting without a matching local interface, don't
assign sequence numbers at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a driver requests additional headroom it should
be mapped to DMA as well because it will be send to
the hardware as well (as form of extra descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.
The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)
Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various rt2x00 devices support hardware encryption.
Most of them require the IV/EIV to be generated by mac80211,
but require it to be provided seperately instead of within
the frame itself. This means that rt2x00lib should extract
the data from the frame and place it in the frame descriptor.
During RX the IV/EIV is provided in the descriptor by the
hardware which means that it should be inserted into the
frame by rt2x00lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sequence counter can be accessed in IRQ context,
which means the lock protecting the counter should
be irqsave. To prevent making the entire intf->lock irqsave
without reason, create a new lock which only protects
the sequence counter.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queues are being initialized the entry flags fields must be
reset to 0. When this does not happen some entries might still be
marked as "occupied" after an ifdown & ifup cycle which would trigger
errors when the entry is being accessed:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Please file bug report to http://rt2x00.serialmonkey.com.
This also fixes the mac80211 warning:
------------[ cut here ]------------
WARNING: at net/mac80211/tx.c:1238 ieee80211_master_start_xmit+0x30a/0x350 [mac80211]()
which was triggered by the queue error.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
