Executing driver on servers with more than 32 CPUs were faced with command
timeouts. This is because we were not geting completions for commands
submitted on IQ32 - IQ63.
Set E64Q bit to enable upper inbound and outbound queues 32 to 63 in the
MPI main configuration table.
Added 500ms delay after successful MPI initialization as mentioned in
controller datasheet.
Link: https://lore.kernel.org/r/20220411064603.668448-3-Ajish.Koshy@microchip.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When upper inbound and outbound queues 32-63 are enabled, we see upper
vectors 32-63 in interrupt service routine. We need corresponding registers
to handle masking and unmasking of these upper interrupts.
To achieve this, we use registers MSGU_ODMR_U(0x34) to mask and
MSGU_ODMR_CLR_U(0x3C) to unmask the interrupts. In these registers bit 0-31
represents interrupt vectors 32-63.
Link: https://lore.kernel.org/r/20220411064603.668448-2-Ajish.Koshy@microchip.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: John Garry <john.garry@huawei.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revert the patch mentioned in the subject since it blocks I/O after module
unload has started while this is a legitimate use case. For e.g. blktests
test case srp/001 that patch causes a command timeout to be triggered for
the following call stack:
__schedule+0x4c3/0xd20
schedule+0x82/0x110
schedule_timeout+0x122/0x200
io_schedule_timeout+0x7b/0xc0
__wait_for_common+0x2bc/0x380
wait_for_completion_io_timeout+0x1d/0x20
blk_execute_rq+0x1db/0x200
__scsi_execute+0x1fb/0x310
sd_sync_cache+0x155/0x2c0 [sd_mod]
sd_shutdown+0xbb/0x190 [sd_mod]
sd_remove+0x5b/0x80 [sd_mod]
device_remove+0x9a/0xb0
device_release_driver_internal+0x2c5/0x360
device_release_driver+0x12/0x20
bus_remove_device+0x1aa/0x270
device_del+0x2d4/0x640
__scsi_remove_device+0x168/0x1a0
scsi_forget_host+0xa8/0xb0
scsi_remove_host+0x9b/0x150
sdebug_driver_remove+0x3d/0x140 [scsi_debug]
device_remove+0x6f/0xb0
device_release_driver_internal+0x2c5/0x360
device_release_driver+0x12/0x20
bus_remove_device+0x1aa/0x270
device_del+0x2d4/0x640
device_unregister+0x18/0x70
sdebug_do_remove_host+0x138/0x180 [scsi_debug]
scsi_debug_exit+0x45/0xd5 [scsi_debug]
__do_sys_delete_module.constprop.0+0x210/0x320
__x64_sys_delete_module+0x1f/0x30
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Link: https://lore.kernel.org/r/20220409043704.28573-1-bvanassche@acm.org
Fixes: 2aad3cd853 ("scsi: scsi_debug: Address races following module load")
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Yi Zhang <yi.zhang@redhat.com>
Cc: Bob Pearson <rpearsonhpe@gmail.com>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
instance->cmd_list is allocated by kcalloc(). The memory is already set to
zero. It is unnecessary to call memset again.
Link: https://lore.kernel.org/r/20220407072442.4137977-1-wanjiabing@vivo.com
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 'struct device' pointer is already cached as a local variable in
ufshcd_pltfrm_init(), so use it.
Link: https://lore.kernel.org/r/20220401085050.119323-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The megaraid_sas driver supports single LUN for RAID devices. That is LUN
0. All other LUNs are unsupported. When a device scan on a logical target
with invalid LUN number is invoked through sysfs, that target ends up
getting removed.
Add LUN ID validation in the slave destroy function to avoid the target
deletion.
Link: https://lore.kernel.org/r/20220324094711.48833-1-chandrakanth.patil@broadcom.com
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The list iterator is always non-NULL so the check 'if (!rgn)' is always
false and the dev_err() is never called. Move the check outside the loop
and determine if 'victim_rgn' is NULL, to fix this bug.
Link: https://lore.kernel.org/r/20220320150733.21824-1-xiam0nd.tong@gmail.com
Fixes: 4b5f49079c ("scsi: ufs: ufshpb: L2P map management for HPB read")
Reviewed-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The HighPoint RocketRaid 2640 is a low-cost SAS controller based on Marvell
chip. The chip in question was already supported by the kernel, just the
PCI ID of this particular board was missing.
Link: https://lore.kernel.org/r/20220309212535.402987-1-agalakhov@gmail.com
Signed-off-by: Alexey Galakhov <agalakhov@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As such it should be called inside the scsi_device_supports_vpd()
conditional.
Link: https://lore.kernel.org/r/20220302053559.32147-13-martin.petersen@oracle.com
Fixes: e815d36548 ("scsi: sd: add concurrent positioning ranges support")
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of controller reset operation the driver issues a config request
command. If this command gets times out, then fail the controller reset
operation instead of retrying it.
Link: https://lore.kernel.org/r/20220405120637.20528-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This driver doesn't use SCp.ptr to save a SCSI command data pointer which
means "scsi pointer" is a complete misnomer here. Only a few members of
struct scsi_pointer are needed so move those to private command data.
Link: https://lore.kernel.org/r/accf71e293ba3aed6d18c8baeb405de8dfe7c935.1649235939.git.fthain@linux-m68k.org
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PCI ID and callbacks to support Intel Meteor Lake (MTL).
Link: https://lore.kernel.org/r/20220404055038.2208051-1-adrian.hunter@intel.com
Cc: stable@vger.kernel.org # v5.15+
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The start_addres argument of mpt3sas_check_same_4gb_region() was misnamed
in the function kdoc comment, resulting in the following warning when
compiling with W=1.
drivers/scsi/mpt3sas/mpt3sas_base.c:5728: warning: Function parameter or
member 'start_address' not described in 'mpt3sas_check_same_4gb_region'
drivers/scsi/mpt3sas/mpt3sas_base.c:5728: warning: Excess function
parameter 'reply_pool_start_address' description in
'mpt3sas_check_same_4gb_region'
Fix the argument name in the function kdoc comment to avoid it. While at
it, remove a useless blank line between the kdoc and function code.
Link: https://lore.kernel.org/r/20220404050041.594774-1-damien.lemoal@opensource.wdc.com
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The in_use_bm bitmap of struct sdebug_queue should be accessed under
protection of the qc_lock spinlock. Make sure that this lock is taken
before calling find_first_bit() at the beginning of the function
sdebug_blk_mq_poll().
Link: https://lore.kernel.org/r/20220404045547.579887-1-damien.lemoal@opensource.wdc.com
Fixes: 3fd07aecb7 ("scsi: scsi_debug: Fix qc_lock use in sdebug_blk_mq_poll()")
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a few spelling mistakes in some error messages. Fix them.
Link: https://lore.kernel.org/r/20220319231445.21696-1-colin.i.king@gmail.com
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The error handling path of the probe releases a resource that is not freed
in the remove function. In some cases, a ioremap() must be undone.
Add the missing iounmap() call in the remove function.
Link: https://lore.kernel.org/r/247066a3104d25f9a05de8b3270fc3c848763bcc.1647673264.git.christophe.jaillet@wanadoo.fr
Fixes: 45804fbb00 ("[SCSI] 53c700: Amiga Zorro NCR53c710 SCSI")
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Common defines should be used over custom defines.
Change and remove these defines:
- PCIR_SUBVEND_0 to PCI_SUBSYSTEM_VENDOR_ID
- PCIR_SUBDEV_0 to PCI_SUBSYSTEM_ID
Link: https://lore.kernel.org/r/20220322144648.2467777-1-trix@redhat.com
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The QCOM UFS driver requires an androidboot.bootdevice command line
argument matching the UFS device name. If the name is different, it
refuses to probe. This androidboot.bootdevice is provided by stock/vendor
(from an Android-based device) bootloader.
This does not make sense from Linux point of view. Driver should be able
to boot regardless of bootloader. Driver should not depend on some Android
custom environment data.
Link: https://lore.kernel.org/r/20220321151853.24138-1-krzk@kernel.org
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig Says:
=======================
I think we should just handle the error properly and remove the comment.
There's no good reason to ignore bsg registration errors.
In fact, after commit 92c4b58b15 ("scsi: core: Register sysfs attributes
earlier"), we are already forced to return errno.
We discuss this issue in [1].
[1] https://lore.kernel.org/all/20211022010201.426746-1-liu.yun@linux.dev/
Link: https://lore.kernel.org/r/20220329021251.123805-1-liu.yun@linux.dev
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This case statement doesn't fall through any more so remove the fallthrough
annotation.
Link: https://lore.kernel.org/r/20220317075214.GC25237@kili
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Eliminate anonymous module_init() and module_exit(), which can lead to
confusion or ambiguity when reading System.map, crashes/oops/bugs, or an
initcall_debug log.
Give each of these init and exit functions unique driver-specific names to
eliminate the anonymous names.
Example 1: (System.map)
ffffffff832fc78c t init
ffffffff832fc79e t init
ffffffff832fc8f8 t init
Example 2: (initcall_debug log)
calling init+0x0/0x12 @ 1
initcall init+0x0/0x12 returned 0 after 15 usecs
calling init+0x0/0x60 @ 1
initcall init+0x0/0x60 returned 0 after 2 usecs
calling init+0x0/0x9a @ 1
initcall init+0x0/0x9a returned 0 after 74 usecs
Link: https://lore.kernel.org/r/20220316192010.19001-6-rdunlap@infradead.org
Fixes: 4fe74b1cb0 ("[SCSI] virtio-scsi: SCSI driver for QEMU based virtual machines")
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit edb854a368 ("scsi: core: Reallocate device's budget map on
queue depth change"), the sbitmap for the device budget map may be
reallocated after the slave device depth is configured.
When the sbitmap is reallocated we use the result from
scsi_device_max_queue_depth() for the sbitmap size, but don't resize to
match the actual device queue depth.
Fix by resizing the sbitmap after reallocating the budget sbitmap. We do
this instead of init'ing the sbitmap to the device queue depth as the user
may want to change the queue depth later via sysfs or other.
Link: https://lore.kernel.org/r/1647423870-143867-1-git-send-email-john.garry@huawei.com
Fixes: edb854a368 ("scsi: core: Reallocate device's budget map on queue depth change")
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove aha152x_cmd_priv.scsi_pointer by moving the necessary members into
aha152x_cmd_priv proper.
Tested with an Adaptec SlimSCSI APA-1460A card.
Link: https://lore.kernel.org/r/bdc1264b6dd331150bffb737958cab8c9c068fa1.1648070977.git.fthain@linux-m68k.org
Cc: Christoph Hellwig <hch@infradead.org>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter request_limit is hardcoded to be INITIAL_SRP_LIMIT which is
currently an arbitrary value of 800. Increase this value to 1024 which
better matches the characteristics of the typical IBMi Initiator that
supports 32 LUNs and a queue depth of 32.
This change also has the secondary benefit of being a power of two as
required by the kfifo API. Since, Commit ab9bb6318b ("Partially revert
"kfifo: fix kfifo_alloc() and kfifo_init()"") the size of IU pool for each
target has been rounded down to 512 when attempting to kfifo_init() those
pools with the current request_limit size of 800.
Link: https://lore.kernel.org/r/20220322194443.678433-1-tyreld@linux.ibm.com
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 2e27f576ab ("scsi: scsi_ioctl: Call scsi_cmd_ioctl() from
scsi_ioctl()") seems to have a typo as it is checking ret instead of cmd in
the if statement checking for CDROMCLOSETRAY and CDROMEJECT. This changes
the behaviour of these ioctls as the cdrom_ioctl handling of these is more
restrictive than the scsi_ioctl version.
Link: https://lore.kernel.org/r/20220323002242.21157-1-kgroeneveld@lenbrook.com
Fixes: 2e27f576ab ("scsi: scsi_ioctl: Call scsi_cmd_ioctl() from scsi_ioctl()")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The whole passthrough ioctl path looks completely broken. For example it
DMA maps the scatterlist and after that copies data to it, which is
prohibited by the DMA API contract.
Moreover, in pmcraid_alloc_sglist(), the pointer returned by a
sgl_alloc_order() call is not recorded anywhere which is pointless.
So remove the PMCRAID_PASSTHROUGH_IOCTL ioctl implementation entirely.
Should it be needed, we should reimplement it using the proper block layer
request mapping helpers.
Link: https://lore.kernel.org/r/7f27a70bec3f3dcaf46a29b1c630edd4792e71c0.1648298857.git.christophe.jaillet@wanadoo.fr
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The request_queue may be NULL in a request, for example when it comes from
scsi_ioctl_reset(). Check it before use.
Fixes: f3fa33acca ("block: remove the ->rq_disk field in struct request")
Link: https://lore.kernel.org/r/20220324134603.28463-1-thenzl@redhat.com
Reported-by: Changhui Zhong <czhong@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove unused fields 'rpm_lvl_attr' and 'spm_lvl_attr' in struct ufs_hba.
Commit cbb6813ee7 ("scsi: ufs: sysfs: attribute group for existing sysfs
entries.") removed all code using that field.
Link: https://lore.kernel.org/r/413601558.101648105683746.JavaMail.epsvc@epcpadp4
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The rules changed for lpfc_sli_iocbq_lookup() vs locking. Prior, the
routine properly took out the lock. In newly refactored code, the locks
must be held when calling the routine.
Fix lpfc_sli_process_sol_iocb() to take the locks before calling the
routine.
Fix lpfc_sli_handle_fast_ring_event() to not release the locks to call the
routine.
Link: https://lore.kernel.org/r/20220323205545.81814-3-jsmart2021@gmail.com
Fixes: 1b64aa9eae ("scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4")
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was a merge error in ther 14.2.0.0 patches that resulted in the SLI4
path using the SLI3 issue_abort_iotag() routine. This resulted in txcmplq
corruption.
Fix to use the SLI4 routine when SLI4.
Link: https://lore.kernel.org/r/20220323205545.81814-2-jsmart2021@gmail.com
Fixes: 31a59f7570 ("scsi: lpfc: SLI path split: Refactor Abort paths")
Cc: <stable@vger.kernel.org> # v5.2+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 14.2.0.1
Link: https://lore.kernel.org/r/20220317032737.45308-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When recovering from a pci-parity error the driver is failing to re-create
queues, causing recovery to fail. Looking deeper, it was found that the
interrupt vector count allocated on the recovery was fewer than the vectors
originally allocated. This disparity resulted in CPU map entries with stale
information. When the driver tries to re-create the queues, it attempts to
use the stale information which indicates an eq/interrupt vector that was
no longer created.
Fix by clearng the cpup map array before enabling and requesting the IRQs
in the lpfc_sli_reset_slot_s4 routine().
Link: https://lore.kernel.org/r/20220317032737.45308-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When injecting EEH errors the port is getting hung up waiting on the node
list to empty, message number 0233. The driver is stuck at this point and
also can't unload. The driver makes transport remoteport delete calls which
try to abort I/O's, but the EEH daemon has already called the driver to
detach and the detachment has set the global FC_UNLOADING flag. There are
several code paths that will avoid I/O cleanup if the FC_UNLOADING flag is
set, resulting in transports waiting for I/O while the driver is waiting on
transports to clean up.
Additionally, during study of the list, a locking issue was found in
lpfc_sli_abort_iocb_ring that could corrupt the list.
A special case was added to the lpfc_cleanup() routine to call
lpfc_sli_flush_rings() if the driver is FC_UNLOADING and if the pci-slot
is offline (e.g. EEH).
The SLI4 part of lpfc_sli_abort_iocb_ring() is changed to use the
ring_lock. Also added code to cancel the I/Os if the pci-slot is offline
and added checks and returns for the FC_UNLOADING and HBA_IOQ_FLUSH flags
to prevent trying to send an I/O that we cannot handle.
Link: https://lore.kernel.org/r/20220317032737.45308-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following EEH errors, the driver can crash or hang when deleting the
localport or when attempting to unload.
The EEH handlers in the driver did not notify the NVMe-FC transport before
tearing the driver down. This was delayed until the resume steps. This
worked for SCSI because lpfc_block_scsi() would notify the
scsi_fc_transport that the target was not available but it would not clean
up all the references to the ndlp.
The SLI3 prep for dev reset handler did the lpfc_offline_prep() and
lpfc_offline() calls to get the port stopped before restarting. The SLI4
version of the prep for dev reset just destroyed the queues and did not
stop NVMe from continuing. Also because the port was not really stopped
the localport destroy would hang because the transport was still waiting
for I/O. Additionally, a devloss tmo can fire and post events to a stopped
worker thread creating another hang condition.
lpfc_sli4_prep_dev_for_reset() is modified to call lpfc_offline_prep() and
lpfc_offline() rather than just lpfc_scsi_dev_block() to ensure both SCSI
and NVMe transports are notified to block I/O to the driver.
Logic is added to devloss handler and worker thread to clean up ndlp
references and quiesce appropriately.
Link: https://lore.kernel.org/r/20220317032737.45308-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
iscsi_cls_conn is alloced by kzalloc(), the whole iscsi_cls_conn is zero
filled already including the dd_data. So it is unnecessary to call memset
again.
Link: https://lore.kernel.org/r/20220317150116.194140-1-haowenchao@huawei.com
Reviewed-by: Wu Bo <wubo40@huawei.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Wenchao Hao <haowenchao@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function mpt3sas_transport_port_remove() called in
_scsih_expander_node_remove() frees the port field of the sas_expander
structure, leading to the following use-after-free splat from KASAN when
the ioc_info() call following that function is executed (e.g. when doing
rmmod of the driver module):
[ 3479.371167] ==================================================================
[ 3479.378496] BUG: KASAN: use-after-free in _scsih_expander_node_remove+0x710/0x750 [mpt3sas]
[ 3479.386936] Read of size 1 at addr ffff8881c037691c by task rmmod/1531
[ 3479.393524]
[ 3479.395035] CPU: 18 PID: 1531 Comm: rmmod Not tainted 5.17.0-rc8+ #1436
[ 3479.401712] Hardware name: Supermicro Super Server/H12SSL-NT, BIOS 2.1 06/02/2021
[ 3479.409263] Call Trace:
[ 3479.411743] <TASK>
[ 3479.413875] dump_stack_lvl+0x45/0x59
[ 3479.417582] print_address_description.constprop.0+0x1f/0x120
[ 3479.423389] ? _scsih_expander_node_remove+0x710/0x750 [mpt3sas]
[ 3479.429469] kasan_report.cold+0x83/0xdf
[ 3479.433438] ? _scsih_expander_node_remove+0x710/0x750 [mpt3sas]
[ 3479.439514] _scsih_expander_node_remove+0x710/0x750 [mpt3sas]
[ 3479.445411] ? _raw_spin_unlock_irqrestore+0x2d/0x40
[ 3479.452032] scsih_remove+0x525/0xc90 [mpt3sas]
[ 3479.458212] ? mpt3sas_expander_remove+0x1d0/0x1d0 [mpt3sas]
[ 3479.465529] ? down_write+0xde/0x150
[ 3479.470746] ? up_write+0x14d/0x460
[ 3479.475840] ? kernfs_find_ns+0x137/0x310
[ 3479.481438] pci_device_remove+0x65/0x110
[ 3479.487013] __device_release_driver+0x316/0x680
[ 3479.493180] driver_detach+0x1ec/0x2d0
[ 3479.498499] bus_remove_driver+0xe7/0x2d0
[ 3479.504081] pci_unregister_driver+0x26/0x250
[ 3479.510033] _mpt3sas_exit+0x2b/0x6cf [mpt3sas]
[ 3479.516144] __x64_sys_delete_module+0x2fd/0x510
[ 3479.522315] ? free_module+0xaa0/0xaa0
[ 3479.527593] ? __cond_resched+0x1c/0x90
[ 3479.532951] ? lockdep_hardirqs_on_prepare+0x273/0x3e0
[ 3479.539607] ? syscall_enter_from_user_mode+0x21/0x70
[ 3479.546161] ? trace_hardirqs_on+0x1c/0x110
[ 3479.551828] do_syscall_64+0x35/0x80
[ 3479.556884] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 3479.563402] RIP: 0033:0x7f1fc482483b
...
[ 3479.943087] ==================================================================
Fix this by introducing the local variable port_id to store the port ID
value before executing mpt3sas_transport_port_remove(). This local variable
is then used in the call to ioc_info() instead of dereferencing the freed
port structure.
Link: https://lore.kernel.org/r/20220322055702.95276-1-damien.lemoal@opensource.wdc.com
Fixes: 7d310f2410 ("scsi: mpt3sas: Get device objects using sas_address & portID")
Cc: stable@vger.kernel.org
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYkF9UwAKCRCAXGG7T9hj
vsXpAPwKXI4WIQcvnVCdULQfuXpA1TbD5XZuS9OuiN/OxWHbzAEA1VHWTmS+tpZ1
ptOyoGhAWhTGeplToobDSGz5qTXEPAI=
=FaKX
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- A bunch of minor cleanups
- A fix for kexec in Xen dom0 when executed on a high cpu number
- A fix for resuming after suspend of a Xen guest with assigned PCI
devices
- A fix for a crash due to not disabled preemption when resuming as Xen
dom0
* tag 'for-linus-5.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: fix is_xen_pmu()
xen: don't hang when resuming PCI device
arch:x86:xen: Remove unnecessary assignment in xen_apic_read()
xen/grant-table: remove readonly parameter from functions
xen/grant-table: remove gnttab_*transfer*() functions
drivers/xen: use helper macro __ATTR_RW
x86/xen: Fix kerneldoc warning
xen: delay xen_hvm_init_time_ops() if kdump is boot on vcpu>=32
xen: use time_is_before_eq_jiffies() instead of open coding it
This series consists of the usual driver updates (qla2xxx, pm8001,
libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
and bug fixes. The high blast radius core update is the removal of
write same, which affects block and several non-SCSI devices. The
other big change, which is more local, is the removal of the SCSI
pointer.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYjzDQyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQMYAQDEWUGV
6U0+736AHVtOfiMNfiRN79B1HfXVoHvemnPcTwD/UlndwFfy/3GGOtoZmqEpc73J
Ec1HDuUCE18H1H2QAh0=
=/Ty9
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (qla2xxx, pm8001,
libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
and bug fixes.
The high blast radius core update is the removal of write same, which
affects block and several non-SCSI devices. The other big change,
which is more local, is the removal of the SCSI pointer"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (281 commits)
scsi: scsi_ioctl: Drop needless assignment in sg_io()
scsi: bsg: Drop needless assignment in scsi_bsg_sg_io_fn()
scsi: lpfc: Copyright updates for 14.2.0.0 patches
scsi: lpfc: Update lpfc version to 14.2.0.0
scsi: lpfc: SLI path split: Refactor BSG paths
scsi: lpfc: SLI path split: Refactor Abort paths
scsi: lpfc: SLI path split: Refactor SCSI paths
scsi: lpfc: SLI path split: Refactor CT paths
scsi: lpfc: SLI path split: Refactor misc ELS paths
scsi: lpfc: SLI path split: Refactor VMID paths
scsi: lpfc: SLI path split: Refactor FDISC paths
scsi: lpfc: SLI path split: Refactor LS_RJT paths
scsi: lpfc: SLI path split: Refactor LS_ACC paths
scsi: lpfc: SLI path split: Refactor the RSCN/SCR/RDF/EDC/FARPR paths
scsi: lpfc: SLI path split: Refactor PLOGI/PRLI/ADISC/LOGO paths
scsi: lpfc: SLI path split: Refactor base ELS paths and the FLOGI path
scsi: lpfc: SLI path split: Introduce lpfc_prep_wqe
scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4
scsi: lpfc: SLI path split: Refactor lpfc_iocbq
scsi: lpfc: Use kcalloc()
...
Hi Linus,
Please, pull the following treewide patch that replaces zero-length arrays with
flexible-array members. This patch has been baking in linux-next for a
whole development cycle.
Thanks
--
Gustavo
-----BEGIN PGP SIGNATURE-----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=xZD2
-----END PGP SIGNATURE-----
Merge tag 'flexible-array-transformations-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull flexible-array transformations from Gustavo Silva:
"Treewide patch that replaces zero-length arrays with flexible-array
members.
This has been baking in linux-next for a whole development cycle"
* tag 'flexible-array-transformations-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
treewide: Replace zero-length arrays with flexible-array members
There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good. This
was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly
tricky and error-prone code.
There is a small merge conflict against a parisc cleanup, the
solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel. The
hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
There are some obvious conflicts against changes to the removed
files.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks.
-----BEGIN PGP SIGNATURE-----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=vtCN
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good.
This was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly tricky
and error-prone code. There is a small merge conflict against a
parisc cleanup, the solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel.
The hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks"
* tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (27 commits)
nds32: Remove the architecture
uaccess: remove CONFIG_SET_FS
ia64: remove CONFIG_SET_FS support
sh: remove CONFIG_SET_FS support
sparc64: remove CONFIG_SET_FS support
lib/test_lockup: fix kernel pointer check for separate address spaces
uaccess: generalize access_ok()
uaccess: fix type mismatch warnings from access_ok()
arm64: simplify access_ok()
m68k: fix access_ok for coldfire
MIPS: use simpler access_ok()
MIPS: Handle address errors for accesses above CPU max virtual user address
uaccess: add generic __{get,put}_kernel_nofault
nios2: drop access_ok() check from __put_user()
x86: use more conventional access_ok() definition
x86: remove __range_not_ok()
sparc64: add __{get,put}_kernel_nofault()
nds32: fix access_ok() checks in get/put_user
uaccess: fix nios2 and microblaze get_user_8()
sparc64: fix building assembly files
...
Two small(ish) fixes, both in drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYjYy2SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZEpAQDQ+I9z
+PAJL1FBBaydO0VsuScxzTbi/fT3CR0ZcmgyjwD7BrPMfM9N+Kg/SAflMVlDSnHP
FXh2d/cQfz30iSdV/nc=
=ytm1
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small(ish) fixes, both in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fnic: Finish scsi_cmnd before dropping the spinlock
scsi: mpt3sas: Page fault in reply q processing
The gnttab_end_foreign_access() family of functions is taking a
"readonly" parameter, which isn't used. Remove it from the function
parameters.
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220311103429.12845-3-jgross@suse.com
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Commit 01d0c69853 ("sr: implement ->free_disk to simplify refcounting")
refactored sr_block_open(), initialized one variable with a duplicate
assignment (probably an unintended copy & paste duplication) and turned one
error case into an early return, which makes the initialization of the
return variable needless.
So, simplify the local variable initialization in sr_block_open() to make
the code a bit more clear.
No functional change. No change in resulting object code.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220314150321.17720-1-lukas.bulwahn@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit ce70fd9a55 ("scsi: core: Remove the cmd field from struct
scsi_request") refactored sg_io(), so that it does not allocate directly
and hence does not return -ENOMEM in its error case. That makes a remaining
assignment of -ENOMEM to the return variable needless.
Drop this needless assignment in sg_io().
No functional change. No change in resulting object code.
Link: https://lore.kernel.org/r/20220315061520.30745-1-lukas.bulwahn@gmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit ce70fd9a55 ("scsi: core: Remove the cmd field from struct
scsi_request") refactored scsi_bsg_sg_io_fn() so that it does not allocate
directly and hence does not return -ENOMEM in its error case. That makes a
remaining assignment of -ENOMEM to the return variable needless.
Drop this needless assignment in scsi_bsg_sg_io_fn().
No functional change. No change in resulting object code.
Link: https://lore.kernel.org/r/20220315055325.14974-1-lukas.bulwahn@gmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When aborting a SCSI command through fnic, there is a race with the fnic
interrupt handler which can result in the SCSI command and its request
being completed twice. If the interrupt handler claims the command by
setting CMD_SP to NULL first, the abort handler assumes the interrupt
handler has completed the command and returns SUCCESS, causing the request
for the scsi_cmnd to be re-queued.
But the interrupt handler may not have finished the command yet. After it
drops the spinlock protecting CMD_SP, it does memory cleanup before finally
calling scsi_done() to complete the scsi_cmnd. If the call to scsi_done
occurs after the abort handler finishes and re-queues the request, the
completion of the scsi_cmnd will advance and try to double complete a
request already queued for retry.
This patch fixes the issue by moving scsi_done() and any other use of
scsi_cmnd to before the spinlock is released by the interrupt handler.
Link: https://lore.kernel.org/r/20220311184359.2345319-1-djeffery@redhat.com
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyrights to 2022 for files modified in the 14.2.0.0 patch set.
Link: https://lore.kernel.org/r/20220225022308.16486-18-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 14.2.0.0
Link: https://lore.kernel.org/r/20220225022308.16486-17-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the BSG paths to use SLI-4 as the primary interface.
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-16-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the Abort paths to use SLI-4 as the primary interface.
- Introduce generic lpfc_sli_prep_abort_xri jump table routine
- Consolidate lpfc_sli4_issue_abort_iotag and lpfc_sli_issue_abort_iotag
into a single generic lpfc_sli_issue_abort_iotag routine
- Consolidate lpfc_sli4_abort_fcp_cmpl and lpfc_sli_abort_fcp_cmpl into a
single generic lpfc_sli_abort_fcp_cmpl routine
- Remove unused routine lpfc_get_iocb_from_iocbq
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-15-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the SCSI paths to use SLI-4 as the primary interface.
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-14-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the CT paths to use SLI-4 as the primary interface.
- Introduce generic lpfc_sli_prep_gen_req jump table routine
- Introduce generic lpfc_sli_prep_xmit_seq64 jump table routine
- Rename lpfcdiag_loop_post_rxbufs to lpfcdiag_sli3_loop_post_rxbufs to
indicate that it is an SLI3 only path
- Create new prep_wqe routine for unsolicited ELS rsp WQEs.
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-13-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the remaining ELS paths to use SLI-4 as the primary
interface. Paths include RRQ, RSCN, unsolicited ELS RQST and RSP paths, ELS
timeouts, etc.:
- Remove unused routines lpfc_sli4_bpl2sgl and lpfc_sli4_iocb2wqe
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-12-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the VMID paths to use SLI-4 as the primary interface:
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-11-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the FDISC paths to use SLI-4 as the primary interface:
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the LS_RJT paths to use SLI-4 as the primary
interface:
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the LS_ACC paths to use SLI-4 as the primary
interface:
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-8-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the SLI3/SLI4 RSCN/SCR/RDF/EDC/FARPR paths to use
SLI-4 as the primary interface:
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch refactors the PLOGI/PRLI/ADISC/LOGO paths to use SLI-4 as
the primary interface:
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-6-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The patch refactors the general ELS handling paths to migrate to SLI-4
structures or common element abstractions. The fabric login paths are
revised as part of this patch:
- New generic lpfc_sli_prep_els_req_rsp jump table routine
- Introduce ls_rjt_error_be and ulp_bde64_le unions to correct legacy
endianness assignments
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
- Clean up poor indentation on some of the ELS paths
Link: https://lore.kernel.org/r/20220225022308.16486-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce lpfc_prep_wqe routine.
The lpfc_prep_wqe() routine is used with lpfc_sli_issue_iocb() and
lpfc_sli_issue_iocb_wait(). The routine performs additional SLI-4 wqe field
setting that the generic routines did not perform as they kept their
actions compatible with both SLI3 and SLI4.
Link: https://lore.kernel.org/r/20220225022308.16486-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert the SLI4 fast and slow paths to use native SLI4 wqe constructs
instead of iocb SLI3-isms.
Includes the following:
- Create simple get_xxx and set_xxx routines to wrapper access to common
elements in both SLI3 and SLI4 commands - allowing calling routines to
avoid sli-rev-specific structures to access the elements.
- using the wqe in the job structure as the primary element
- use defines from SLI-4, not SLI-3
- Removal of iocb to wqe conversion from fast and slow path
- Add below routines to handle fast path
lpfc_prep_embed_io - prepares the wqe for fast path
lpfc_wqe_bpl2sgl - manages bpl to sgl conversion
lpfc_sli_wqe2iocb - converts a WQE to IOCB for SLI-3 path
- Add lpfc_sli3_iocb2wcqecmpl in completion path to convert an SLI-3
iocb completion to wcqe completion
- Refactor some of the code that works on both revs for clarity
Link: https://lore.kernel.org/r/20220225022308.16486-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, SLI3 and SLI4 data paths use the same lpfc_iocbq structure.
This is a "common" structure but many of the components refer to sli-rev
specific entities which can lead the developer astray as to what they
actually mean, should be set to, or when they should be used.
This first patch prepares the lpfc_iocbq structure so that elements common
to both SLI3 and SLI4 data paths are more appropriately named, making it
clear they apply generically.
Fieldnames based on 'iocb' (sli3) or 'wqe' (sli4) which are actually
generic to the paths are renamed to 'cmd':
- iocb_flag is renamed to cmd_flag
- lpfc_vmid_iocb_tag is renamed to lpfc_vmid_tag
- fabric_iocb_cmpl is renamed to fabric_cmd_cmpl
- wait_iocb_cmpl is renamed to wait_cmd_cmpl
- iocb_cmpl and wqe_cmpl are combined and renamed to cmd_cmpl
- rsvd2 member is renamed to num_bdes due to pre-existing usage
The structure name itself will retain the iocb reference as changing to a
more relevant "job" or "cmd" title induces many hundreds of line changes
for only a name change.
lpfc_post_buffer is also renamed to lpfc_sli3_post_buffer to indicate use
in the SLI3 path only.
Link: https://lore.kernel.org/r/20220225022308.16486-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During SNS Register FC-4 Features (RFF_ID) the initiator driver was sending
incorrect type field for NVMe supported device. Use correct feature type
field.
Link: https://lore.kernel.org/r/20220310092604.22950-12-njavali@marvell.com
Fixes: e374f9f592 ("scsi: qla2xxx: Migrate switch registration commands away from mailbox interface")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While a session is in the middle of a relogin, a late RSCN can be delivered
from switch. RSCN trigger fabric scan where the scan logic can trigger
another session login while a login is in progress. Reduce the extra
trigger to prevent multiple logins to the same session.
Link: https://lore.kernel.org/r/20220310092604.22950-10-njavali@marvell.com
Fixes: bee8b84686 ("scsi: qla2xxx: Reduce redundant ADISC command for RSCNs")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For session recovery, driver relies on the dpc thread to initiate certain
operations. The dpc thread runs exclusively without the Mailbox interface
being occupied. A recent code change for heartbeat check via mailbox cmd 0
is preventing the dpc thread from carrying out its operation. This patch
allows the higher priority error recovery to run first before running the
lower priority heartbeat check.
Link: https://lore.kernel.org/r/20220310092604.22950-9-njavali@marvell.com
Fixes: d94d8158e1 ("scsi: qla2xxx: Add heartbeat check")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
User experienced device lost. The log shows Get port data base command was
queued up, failed, and requeued again. Every time it is requeued, it set
the FCF_ASYNC_ACTIVE. This prevents any recovery code from occurring
because driver thinks a recovery is in progress for this session. In
essence, this session is hung. The reason it gets into this place is the
session deletion got in front of this call due to link perturbation.
Break the requeue cycle and exit. The session deletion code will trigger a
session relogin.
Link: https://lore.kernel.org/r/20220310092604.22950-8-njavali@marvell.com
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For N2N topology, ELS Passthrough is used to send PLOGI. On failure of ELS
pass through PLOGI, driver flipped over to using LLIOCB PLOGI for N2N. This
is not consistent. Delete the session to restart the connection where ELS
pass through PLOGI would be used consistently.
Link: https://lore.kernel.org/r/20220310092604.22950-7-njavali@marvell.com
Fixes: c76ae845ea ("scsi: qla2xxx: Add error handling for PLOGI ELS passthrough")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During purex packet handling the driver was incorrectly freeing a
pre-allocated structure. Fix this by skipping that entry.
System crashed with the following stack during a module unload test.
Call Trace:
sbitmap_init_node+0x7f/0x1e0
sbitmap_queue_init_node+0x24/0x150
blk_mq_init_bitmaps+0x3d/0xa0
blk_mq_init_tags+0x68/0x90
blk_mq_alloc_map_and_rqs+0x44/0x120
blk_mq_alloc_set_map_and_rqs+0x63/0x150
blk_mq_alloc_tag_set+0x11b/0x230
scsi_add_host_with_dma.cold+0x3f/0x245
qla2x00_probe_one+0xd5a/0x1b80 [qla2xxx]
Call Trace with slub_debug and debug kernel:
kasan_report_invalid_free+0x50/0x80
__kasan_slab_free+0x137/0x150
slab_free_freelist_hook+0xc6/0x190
kfree+0xe8/0x2e0
qla2x00_free_device+0x3bb/0x5d0 [qla2xxx]
qla2x00_remove_one+0x668/0xcf0 [qla2xxx]
Link: https://lore.kernel.org/r/20220310092604.22950-6-njavali@marvell.com
Fixes: 62e9dd1777 ("scsi: qla2xxx: Change in PUREX to handle FPIN ELS requests")
Cc: stable@vger.kernel.org
Reported-by: Marco Patalano <mpatalan@redhat.com>
Tested-by: Marco Patalano <mpatalan@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At NVMe ELS request time, request structure is DMA mapped and never
unmapped. Fix this by calling the unmap on ELS completion.
Link: https://lore.kernel.org/r/20220310092604.22950-5-njavali@marvell.com
Fixes: e84067d743 ("scsi: qla2xxx: Add FC-NVMe F/W initialization and transport registration")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver registration of localport can race when it happens at the remote
port discovery time. Fix this by calling the registration under a mutex.
Link: https://lore.kernel.org/r/20220310092604.22950-4-njavali@marvell.com
Fixes: e84067d743 ("scsi: qla2xxx: Add FC-NVMe F/W initialization and transport registration")
Cc: stable@vger.kernel.org
Reported-by: Marco Patalano <mpatalan@redhat.com>
Tested-by: Marco Patalano <mpatalan@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
User experienced some of the LUN failed to get rediscovered after long
cable pull test. The issue is triggered by a race condition between driver
setting session online state vs starting the LUN scan process at the same
time. Current code set the online state after notifying the session is
available. In this case, trigger to start the LUN scan process happened
before driver could set the session in online state. LUN scan ends up with
failure due to the session online check was failing.
Set the online state before reporting of the availability of the session.
Link: https://lore.kernel.org/r/20220310092604.22950-3-njavali@marvell.com
Fixes: aecf043443 ("scsi: qla2xxx: Fix Remote port registration")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
User experienced no task management error while target device is responding
with error. The RSP_CODE field in the status IOCB is in little endian.
Driver assumes it's big endian and it picked up erroneous data.
Convert the data back to big endian as is on the wire.
Link: https://lore.kernel.org/r/20220310092604.22950-2-njavali@marvell.com
Fixes: faef62d134 ("[SCSI] qla2xxx: Fix Task Management command asynchronous handling")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1b8d0300a3 ("scsi: libiscsi: Fix UAF in
iscsi_conn_get_param()/iscsi_conn_teardown()") fixed an UAF in
iscsi_conn_get_param() and introduced 2 tmp_xxx varibles.
We can gracefully fix this UAF with the help of device_del(). Calling
iscsi_remove_conn() at the beginning of iscsi_conn_teardown would make
userspace unable to see iscsi_cls_conn. This way we we can free memory
safely.
Remove iscsi_destroy_conn() since it is no longer used.
Link: https://lore.kernel.org/r/20220310015759.3296841-4-haowenchao@huawei.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Wenchao Hao <haowenchao@huawei.com>
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
iscsi_create_conn() exposed iscsi_cls_conn to sysfs prior to initialization
of iscsi_conn's dd_data. When userspace tried to access an attribute such
as the connect address, a NULL pointer dereference was observed.
Do not add iscsi_cls_conn to sysfs until it has been initialized. Remove
iscsi_create_conn() since it is no longer used.
Link: https://lore.kernel.org/r/20220310015759.3296841-3-haowenchao@huawei.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Wenchao Hao <haowenchao@huawei.com>
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- iscsi_alloc_conn(): Allocate and initialize iscsi_cls_conn
- iscsi_add_conn(): Expose iscsi_cls_conn to userspace via sysfs
- iscsi_remove_conn(): Remove iscsi_cls_conn from sysfs
Link: https://lore.kernel.org/r/20220310015759.3296841-2-haowenchao@huawei.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Wenchao Hao <haowenchao@huawei.com>
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The smatch tool reported the following warning:
drivers/scsi/scsi_error.c:1988 scsi_decide_disposition() warn: ignoring
unreachable code.
Remove the "default:return FAILED;" instead of "return FAILED;" reported by
smatch, because compilers can provide more useful diagnostics about
switch/case statements that do not have a default statement, especially if
the "switch" applies to a value with enumeration type.
Link: https://lore.kernel.org/r/20220301080448.112813-1-yang.lee@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Eliminate the following smatch warning:
drivers/scsi/megaraid/megaraid_sas_fusion.c:5104 megasas_reset_fusion()
warn: inconsistent indenting
Link: https://lore.kernel.org/r/20220225011605.130927-1-yang.lee@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the common libsas internal abort functionality.
In addition, this driver has special handling for internal abort timeouts -
specifically whether to reset the controller in that instance, so extend
the API for that.
Timeout is now increased to 20 * Hz from 6 * Hz.
We also retry for failure now, but this should not make a difference.
Link: https://lore.kernel.org/r/1647001432-239276-5-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New special handling is added for SAS_PROTOCOL_INTERNAL_ABORT proto so that
we may use the common queue command API.
Link: https://lore.kernel.org/r/1647001432-239276-4-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for a "device" variant of internal abort, which will abort all
pending I/Os for a specific device.
Link: https://lore.kernel.org/r/1647001432-239276-3-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The internal abort feature is common to hisi_sas and pm8001 HBAs, and the
driver support is similar also, so add a common handler.
Two modes of operation will be supported:
- single: Abort a single tagged command
- device: Abort all commands associated with a specific domain device
A new protocol is added, SAS_PROTOCOL_INTERNAL_ABORT, so the common queue
command API may be re-used.
Only add "single" support as a first step.
Link: https://lore.kernel.org/r/1647001432-239276-2-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The soft_wwpn/soft_wwn functionality, which allows the driver to modify
service parameters in an attempt to override the adapter-assigned WWN, was
originally attempted to be removed roughly 6 yrs ago as new fabric features
were being introduced that clashed with the implementation. In the end,
the feature was left in with the user being responsible if things went
south.
We've reached a point where soft_wwn is no longer functional and is failing
in almost all production use cases. Use of Fabric features such as Fabric
Assigned WWPN and Automatic DPORT is now prevalent and the features require
coordination between the adapter and driver that can't be solved by the
simplistic update of the service parameters. As it is no longer functional,
the feature is to be removed.
There are still ways to override the adapter-assigned WWN but they require
the admin to invoke bios/efi level menus.
Link: https://lore.kernel.org/r/20220310154845.11125-1-jsmart2021@gmail.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When ufs initializes without scmd->device->sector_size set, scsi_get_lba()
will get a wrong shift number and trigger an ubsan error. The shift
exponent 4294967286 is too large for the 64-bit type 'sector_t' (aka
'unsigned long long').
Call scsi_get_lba() only when opcode is READ_10/WRITE_10/UNMAP.
Link: https://lore.kernel.org/r/20220307111752.10465-1-peter.wang@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver must perform its 4GB boundary check using the pool's DMA address
instead of using the virtual address.
Link: https://lore.kernel.org/r/20220303140230.13098-1-sreekanth.reddy@broadcom.com
Fixes: d6adc251dd ("scsi: mpt3sas: Force PCIe scatterlist allocations to be within same 4 GB region")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When scsi_dma_map() fails by returning a sges_left value less than zero,
the amount of logging produced can be extremely high. In a recent end-user
environment, 1200 messages per second were being sent to the log buffer.
This eventually overwhelmed the system and it stalled.
These error messages are not needed. Remove them.
Link: https://lore.kernel.org/r/20220303140203.12642-1-sreekanth.reddy@broadcom.com
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fc_exch_release(ep) will decrease the ep's reference count. When the
reference count reaches zero, it is freed. But ep is still used in the
following code, which will lead to a use after free.
Return after the fc_exch_release() call to avoid use after free.
Link: https://lore.kernel.org/r/20220303015115.459778-1-niejianglei2021@163.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The use of the 'locked' boolean variable to control locking and unlocking
of the qc_lock spinlock of struct sdebug_queue confuses sparse, leading to
a warning about an unexpected unlock. Simplify the qc_lock lock/unlock
handling code of this function to avoid this warning by removing the
'locked' boolean variable. This change also fixes unlocked access to the
in_use_bm bitmap with the find_first_bit() function.
Link: https://lore.kernel.org/r/20220301113009.595857-3-damien.lemoal@opensource.wdc.com
Fixes: b05d4e481e ("scsi: scsi_debug: Refine sdebug_blk_mq_poll()")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return statement inside the sdeb_read_lock(), sdeb_read_unlock(),
sdeb_write_lock() and sdeb_write_unlock() confuse sparse, leading to many
warnings about unexpected unlocks in the resp_xxx() functions.
Modify the lock/unlock functions using the __acquire() and __release()
inline annotations for the sdebug_no_rwlock == true case to avoid these
warnings.
Link: https://lore.kernel.org/r/20220301113009.595857-2-damien.lemoal@opensource.wdc.com
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simplify the refcounting and remove the need to clear disk->private_data
by implementing the ->free_disk method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Implement the ->free_disk method to to put struct scsi_disk when the last
gendisk reference count goes away. This removes the need to clear
->private_data and thus freeze the queue on unbind.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Call free_opal_dev from scsi_disk_release as the opal_dev field is accessed
from the ioctl handler, which isn't synchronized vs sd_release and thus
can be accessed during or after sd_release was called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
sd_zbc_release_disk accesses disk->device, so ensure that actually still has
a valid reference.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
dev is very hard to grep for. Give the field a more descriptive name and
documents its purpose.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Requiring every ULP to have the scsi_drive as first member of the
private data is rather fragile and not necessary anyway. Just use
the driver hanging off the SCSI device instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_try_end_foreign_access() and check the
success of that operation instead.
This is CVE-2022-23038 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
---
V2:
- use gnttab_try_end_foreign_access()
Kernel messages produced during runtime PM can cause a never-ending cycle
because user space utilities (e.g. journald or rsyslog) write the messages
back to storage, causing runtime resume, more messages, and so on.
Messages that tell of things that are expected to happen, are arguably
unnecessary, so suppress them.
UFS driver messages are changes to from dev_err() to dev_dbg() which means
they will not display unless activated by dynamic debug of building with
-DDEBUG.
sdev->silence_suspend is set to skip messages from sd_suspend_common()
"Synchronizing SCSI cache", "Stopping disk" and scsi_report_sense()
"Power-on or device reset occurred" message (Note, that message appears
when the LUN is accessed after runtime PM, not during runtime PM)
Example messages from Ubuntu 21.10:
$ dmesg | tail
[ 1620.380071] ufshcd 0000:00:12.5: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0
[ 1620.408825] ufshcd 0000:00:12.5: ufshcd_print_pwr_info:[RX, TX]: gear=[4, 4], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
[ 1620.409020] ufshcd 0000:00:12.5: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0
[ 1620.409524] sd 0:0:0:0: Power-on or device reset occurred
[ 1622.938794] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 1622.939184] ufs_device_wlun 0:0:0:49488: Power-on or device reset occurred
[ 1625.183175] ufshcd 0000:00:12.5: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0
[ 1625.208041] ufshcd 0000:00:12.5: ufshcd_print_pwr_info:[RX, TX]: gear=[4, 4], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
[ 1625.208311] ufshcd 0000:00:12.5: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0
[ 1625.209035] sd 0:0:0:0: Power-on or device reset occurred
Note for stable: depends on patch "scsi: core: sd: Add silence_suspend flag
to suppress some PM messages".
Link: https://lore.kernel.org/r/20220228113652.970857-3-adrian.hunter@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel messages produced during runtime PM can cause a never-ending cycle
because user space utilities (e.g. journald or rsyslog) write the messages
back to storage, causing runtime resume, more messages, and so on.
Messages that tell of things that are expected to happen are arguably
unnecessary, so add a flag to suppress them. This flag is used by the UFS
driver.
Link: https://lore.kernel.org/r/20220228113652.970857-2-adrian.hunter@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We only need the rport structure for lpfc_chk_tgt_mapped().
Link: https://lore.kernel.org/r/20220301143718.40913-6-hare@suse.de
Cc: James Smart <james.smart@broadcom.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of passing in a scsi_cmnd we should be using the rport; we already
have the target and LUN ID as parameters, so there's no need to pass the
scsi_cmnd too.
Link: https://lore.kernel.org/r/20220301143718.40913-5-hare@suse.de
Cc: James Smart <james.smart@broadcom.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use fc_block_rport() instead of fc_block_scsi_eh() as the SCSI command will
be removed as argument for SCSI EH functions.
Link: https://lore.kernel.org/r/20220301143718.40913-4-hare@suse.de
Cc: James Smart <james.smart@broadcom.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The default SCSI EH action for a non-existing EH callback is to return
FAILED, so having a callback just returning FAILED is pointless.
Link: https://lore.kernel.org/r/20220301143718.40913-3-hare@suse.de
Cc: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_bus_reset_handler() is really just a loop calling
lpfc_target_reset_handler() over all targets, which is what the error
handler will be doing anyway.
Link: https://lore.kernel.org/r/20220301143718.40913-2-hare@suse.de
Cc: James Smart <james.smart@broadcom.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During the process of driver probing, the probe function should return < 0
for failure, otherwise the kernel will treat value >= 0 as success.
Set 'err' to the error value returned by dma_set_mask() in case of failure.
Link: https://lore.kernel.org/r/1646060055-11361-1-git-send-email-zheyuma97@gmail.com
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the workqueue code was created it didn't allow variable args so we
have been using a temp buffer. Drop that.
Link: https://lore.kernel.org/r/20220226230435.38733-7-michael.christie@oracle.com
Reviewed-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the session workqueue for recovery and unbinding. If there are delays
during device blocking/cleanup then it will no longer affect other
sessions.
Link: https://lore.kernel.org/r/20220226230435.38733-6-michael.christie@oracle.com
Reviewed-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We currently allocate a workqueue per host and only use it for removing the
target. For the session per host case we could be using this workqueue to
be able to do recoveries (block, unblock, timeout handling) in parallel. To
also allow offload drivers to do their session recoveries in parallel, this
drops the per host workqueue and replaces it with a per session one.
Link: https://lore.kernel.org/r/20220226230435.38733-5-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla4xxx does not use iscsi_scan_finished() anymore so remove it.
Link: https://lore.kernel.org/r/20220226230435.38733-4-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the iSCSI class was added upstream, blocking a queue was fast because
it just set some flag bits and didn't handle I/O that was in the process of
being sent to the driver. That's no longer the case so blocking a queue is
expensive and we can end up with a backlog of blocks by the time we have
relogged in and are trying to start the queues.
For the session unblock case, this has try to cancel the block and recovery
work in case they are still queued so we can avoid unneeded queue
manipulations. For removal, we also now try to cancel all the recovery
related works since a couple lines down we will set the session and device
state so running those functions are not necessary.
Link: https://lore.kernel.org/r/20220226230435.38733-3-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the user sets the iscsi_eh_timer_workq/iscsi_eh workqueue's max_active
to greater than 1, the recovery_work could be running when
__iscsi_unblock_session() runs. The cancel_delayed_work() will then not
wait for the running work and we can race where we end up with the wrong
session state and scsi_device state set.
This replaces the cancel_delayed_work() with the sync version.
Link: https://lore.kernel.org/r/20220226230435.38733-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the original FPIN commit, stats were incremented by the event_count.
Event_count is the minimum # of events that must occur before an FPIN is
sent. Thus, its not the actual number of events, and could be significantly
off (too low) as it doesn't reflect anything not reported. Rather than
attempt to count events, have the statistic count how many FPINS cross the
threshold and were reported.
Link: https://lore.kernel.org/r/20220301175536.60250-1-jsmart2021@gmail.com
Fixes: 3dcfe0de5a ("scsi: fc: Parse FPIN packets and update statistics")
Cc: <stable@vger.kernel.org> # v5.11+
Cc: Shyam Sundar <ssundar@marvell.com>
Cc: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sparse throws a warning about context imbalance ("different lock contexts
for basic block") in sas_form_port() as it gets confused with the fact that
a port is locked within one of the two search loops and unlocked afterward
outside of the search loops once the phy is added to the port. Since this
code is not easy to follow, improve it by factoring out the code adding the
phy to the port once the port is locked into the helper function
sas_form_port_add_phy(). This helper can then be called directly within the
port search loops, avoiding confusion and clearing the sparse warning.
Link: https://lore.kernel.org/r/20220228094857.557329-1-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This header is empty now except for an include of <linux/blk-mq.h>, so
remove it.
Link: https://lore.kernel.org/r/20220224175552.988286-9-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Let submitters initialize the scmd->allowed field directly instead of
indirecting through struct scsi_request and remove the now superfluous
structure.
Link: https://lore.kernel.org/r/20220224175552.988286-8-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prepare for removing the scsi_request structure by moving the result field
to struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220224175552.988286-7-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prepare for removing the scsi_request structure by moving the resid_len
field to struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220224175552.988286-6-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just use the sense_buffer field in struct scsi_cmnd for the sense data and
move the sense_len field over to struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220224175552.988286-5-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that each scsi_request is backed by a scsi_cmnd, there is no need to
indirect the CDB storage. Change all submitters of SCSI passthrough
requests to store the CDB information directly in the scsi_cmnd, and while
doing so allocate the full 32 bytes that cover all Linux supported SCSI
hosts instead of requiring dynamic allocation for > 16 byte CDBs. On
64-bit systems this does not change the size of the scsi_cmnd at all, while
on 32-bit systems it slightly increases it for now, but that increase will
be made up by the removal of the remaining scsi_request fields.
Link: https://lore.kernel.org/r/20220224175552.988286-4-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace the big fat memset that requires saving and restoring various
fields with just initializing those fields that need initialization.
All the clearing to 0 is moved to scsi_prepare_cmd() as scsi_ioctl_reset()
alreadly uses kzalloc() to allocate a pre-zeroed command.
This is still conservative and can probably be optimized further.
Link: https://lore.kernel.org/r/20220224175552.988286-3-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Function queue_work() returns a bool, so use a bool to hold this value for
the return code from callers, which should make the code a tiny bit more
clear.
Also take this opportunity to condense the code of the those callers, such
as sas_queue_work(), as suggested by Damien.
Link: https://lore.kernel.org/r/1645786656-221630-3-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nobody checks the return codes, so make them return void. Indeed, if the
LLDD cannot send an event, nothing much can be done in the LLDD about it.
Also remove prototype for sas_notify_phy_event() in sas_internal.h, which
should not be there.
Link: https://lore.kernel.org/r/1645786656-221630-2-git-send-email-john.garry@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case of SSP underflow allow the response frame IU to be examined for
setting the response stat value rather than always setting
SAS_DATA_UNDERRUN.
This will mean that we call sas_ssp_task_response() in those scenarios and
may send sense data to upper layer.
Such a condition would be for bad blocks were we just reporting an
underflow error to upper layer, but now the sense data will tell
immediately that the media is faulty.
Link: https://lore.kernel.org/r/1645703489-87194-7-git-send-email-john.garry@huawei.com
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a file operation for "cnt" file under bist directory, so users can only
read "cnt" or clear "cnt" to zero, but cannot randomly modify.
Link: https://lore.kernel.org/r/1645703489-87194-6-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the driver probe fails to request the channel IRQ or fatal IRQ, the
driver will free the IRQ vectors before freeing the IRQs in free_irq(),
and this will cause a kernel BUG like this:
------------[ cut here ]------------
kernel BUG at drivers/pci/msi.c:369!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Call trace:
free_msi_irqs+0x118/0x13c
pci_disable_msi+0xfc/0x120
pci_free_irq_vectors+0x24/0x3c
hisi_sas_v3_probe+0x360/0x9d0 [hisi_sas_v3_hw]
local_pci_probe+0x44/0xb0
work_for_cpu_fn+0x20/0x34
process_one_work+0x1d0/0x340
worker_thread+0x2e0/0x460
kthread+0x180/0x190
ret_from_fork+0x10/0x20
---[ end trace b88990335b610c11 ]---
So we use devm_add_action() to control the order in which we free the
vectors.
Link: https://lore.kernel.org/r/1645703489-87194-4-git-send-email-john.garry@huawei.com
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The time of phyup not only depends on the controller but also the type of
disk connected. As an example, from experience, for some SATA disks the
amount of time from reset/power-on to receive the D2H FIS for phyup can
take upto and more than 10s sometimes. According to the specification of
some SATA disks such as ST14000NM0018, the max time from power-on to ready
is 30s.
Based on this the current timeout of phyup at 2s which is not enough. So
set the value as HISI_SAS_WAIT_PHYUP_TIMEOUT (30s) in
hisi_sas_control_phy().
For v3 hw there is a pre-existing workaround for a HW bug, being that we
issue a link reset when the OOB occurs but the phyup does not. The current
phyup timeout is HISI_SAS_WAIT_PHYUP_TIMEOUT. So if this does occur from
when issuing a phy enable or similar via hisi_sas_control_phy(), the
subsequent HW workaround linkreset processing calls hisi_sas_control_phy(),
but this will pend the original phy reset timing out, so it is safe.
Link: https://lore.kernel.org/r/1645703489-87194-3-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the permission of parameter prot_mask is 0x0, which means that
the member does not appear in sysfs. Change it as other module parameters
to 0444 for world-readable.
[mkp: s/v3/v2/]
Link: https://lore.kernel.org/r/1645703489-87194-2-git-send-email-john.garry@huawei.com
Fixes: d6a9000b81 ("scsi: hisi_sas: Add support for DIF feature for v2 hw")
Reported-by: Yihang Li <liyihang6@hisilicon.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
__setup() handlers should return 1 if the command line option is handled
and 0 if not (or maybe never return 0; doing so just pollutes init's
environment with strings that are not init arguments/parameters).
Return 1 from aha152x_setup() to indicate that the boot option has been
handled.
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Link: https://lore.kernel.org/r/20220223000623.5920-1-rdunlap@infradead.org
Cc: "Juergen E. Fischer" <fischer@norbit.de>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware expects host driver to clear scratchpad rsvd 0 register after
non-fatal error is found.
This is done when firmware raises fatal error interrupt and indicates
non-fatal error. At this point firmware updates scratchpad rsvd 0 register
with non-fatal error value. Here host has to clear the register after
reading it during non-fatal errors.
Rename:
- MSGU_HOST_SCRATCH_PAD_6 to MSGU_SCRATCH_PAD_RSVD_0
- MSGU_HOST_SCRATCH_PAD_7 to MSGU_SCRATCH_PAD_RSVD_1
Link: https://lore.kernel.org/r/20220222092618.108198-1-Ajish.Koshy@microchip.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This driver doesn't use SCp.ptr to save a SCSI command data pointer which
means "scsi pointer" is a complete misnomer here. Only a few members of
struct scsi_pointer are used and the rest waste memory. Avoid the "struct
foo { struct bar; };" silliness.
Link: https://lore.kernel.org/r/3529a59873a7de8455a27af2528341afe5069adc.1645484982.git.fthain@linux-m68k.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This driver doesn't use SCp.ptr to save a SCSI command data pointer which
means "scsi pointer" is a complete misnomer here. Only a few members of
struct scsi_pointer are used and the rest waste memory. Avoid the "struct
foo { struct bar; };" silliness.
Link: https://lore.kernel.org/r/fbf930e64af5b15ca028dfe25b00fe933951f19b.1645484982.git.fthain@linux-m68k.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are no remaining callers of set_fs(), so CONFIG_SET_FS
can be removed globally, along with the thread_info field and
any references to it.
This turns access_ok() into a cheaper check against TASK_SIZE_MAX.
As CONFIG_SET_FS is now gone, drop all remaining references to
set_fs()/get_fs(), mm_segment_t, user_addr_max() and uaccess_kernel().
Acked-by: Sam Ravnborg <sam@ravnborg.org> # for sparc32 changes
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Tested-by: Sergey Matyukevich <sergey.matyukevich@synopsys.com> # for arc changes
Acked-by: Stafford Horne <shorne@gmail.com> # [openrisc, asm-generic]
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Make the driver messages more readable by adding a space after the message
prefix ":" and removing the extra space between function name and line
number.
Link: https://lore.kernel.org/r/20220220031810.738362-32-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Both pm8001_send_abort_all() and pm80xx_send_abort_all() are called only
for a non null device with the NCQ_READ_LOG_FLAG set, so remove the device
check on entry of these functions. Furthermore, setting the
NCQ_ABORT_ALL_FLAG device id flag and clearing the NCQ_READ_LOG_FLAG is
always done before calling these functions. Move these operations inside
the functions.
Link: https://lore.kernel.org/r/20220220031810.738362-31-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The task argument of the pm8001_ccb_task_free() function can be inferred
from the ccb argument ccb_task field. So there is no need to have this
argument. Likewise, the ccb_index argument is always equal to the ccb tag
field and is not needed either. Remove both arguments and update all call
sites. The pm8001_ccb_task_free_done() helper is also modified to match
this change.
Link: https://lore.kernel.org/r/20220220031810.738362-30-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The main part of the pm8001_task_exec() function uses a do {} while(0) loop
that is useless and only makes the code harder to read. Remove this
loop. The unnecessary local variable t is also removed.
Additionally, avoid repeatedly declaring "struct task_status_struct *ts" to
handle error cases by declaring this variable for the entire function
scope. This allows simplifying the error cases, and together with the
addition of blank lines make the code more readable.
Finally, handling of the running_req counter is fixed to avoid decrementing
it without a corresponding incrementation in the case of an invalid task
protocol.
Link: https://lore.kernel.org/r/20220220031810.738362-29-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no need to pass a pointer to a struct inbound_queue_table to
pm8001_mpi_build_cmd(). Passing the start index in the inbound queue table
of the adapter is enough. This change allows avoiding the declaration of a
struct inbound_queue_table pointer (circularQ variables) in many functions,
simplifying the code.
While at it, blank lines are added i(e.g. after local variable
declarations) to make the code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-28-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce the pm8001_ccb_alloc() and pm8001_ccb_free() helpers to replace
the typical code patterns:
res = pm8001_tag_alloc(pm8001_ha, &ccb_tag);
if (res)
...
ccb = &pm8001_ha->ccb_info[ccb_tag];
ccb->device = pm8001_ha_dev;
ccb->ccb_tag = ccb_tag;
ccb->task = task;
ccb->n_elem = 0;
and
ccb->task = NULL;
ccb->ccb_tag = PM8001_INVALID_TAG;
pm8001_tag_free(pm8001_ha, tag);
With the simpler function calls:
ccb = pm8001_ccb_alloc(pm8001_ha, pm8001_ha_dev, task);
if (!ccb)
...
and
pm8001_ccb_free(pm8001_ha, ccb);
The pm8001_ccb_alloc() helper ensures that all fields of the ccb info
structure for the newly allocated tag are all initialized, except the
buf_prd field. The pm8001_ccb_free() helper clears the initialized fields
and the ccb tag to ensure that iteration over the adapter ccb_info array
detects ccbs that are in use.
All call site of the pm8001_tag_alloc() function that use a ccb info
associated with an allocated tag are converted to use the new helpers.
Link: https://lore.kernel.org/r/20220220031810.738362-27-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To detect if a command is NCQ, there is no need to test all possible NCQ
command codes. Instead, use ata_is_ncq() to test the command protocol.
Link: https://lore.kernel.org/r/20220220031810.738362-26-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace the goto statement in the for loop with "break" and remove the
ex_err label. Also fix long lines, identation and blank lines to make the
code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-25-damien.lemoal@opensource.wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To detect if a command is NCQ, there is no need to test all possible NCQ
command codes. Instead, use ata_is_ncq() to test the command protocol.
Link: https://lore.kernel.org/r/20220220031810.738362-24-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm8001_chip_fw_flash_update_build(), if
pm8001_chip_fw_flash_update_build() fails, the struct fw_control_ex
allocated must be freed.
Link: https://lore.kernel.org/r/20220220031810.738362-23-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm8001_chip_set_dev_state_req(), pm8001_chip_fw_flash_update_req(),
pm80xx_chip_phy_ctl_req() and pm8001_chip_reg_dev_req() add missing calls
to pm8001_tag_free() to free the allocated tag when pm8001_mpi_build_cmd()
fails.
Similarly, in pm8001_exec_internal_task_abort(), if the chip ->task_abort
method fails, the tag allocated for the abort request task must be
freed. Add the missing call to pm8001_tag_free().
Link: https://lore.kernel.org/r/20220220031810.738362-22-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm8001_send_abort_all(), make sure to free the allocated sas task
if pm8001_tag_alloc() or pm8001_mpi_build_cmd() fail.
Link: https://lore.kernel.org/r/20220220031810.738362-21-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function pm8001_tag_alloc() determines free tags using the function
find_first_zero_bit() which can return 0 when the first bit of the bitmap
being inspected is 0. As such, tag 0 is a valid tag value that should not
be dismissed as invalid. Fix the functions pm8001_work_fn(),
mpi_sata_completion(), pm8001_mpi_task_abort_resp() and
pm8001_open_reject_retry() to not dismiss 0 tags as invalid.
The value 0xffffffff is used for invalid tags for unused ccb information
structures. Add the macro definition PM8001_INVALID_TAG to define this
value.
Link: https://lore.kernel.org/r/20220220031810.738362-20-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The call to pm8001_ccb_task_free() at the end of
pm8001_mpi_task_abort_resp() already frees the ccb tag. So when the device
NCQ_ABORT_ALL_FLAG is set, the tag should not be freed again. Also change
the hardcoded 0xBFFFFFFF value to ~NCQ_ABORT_ALL_FLAG as it ought to be.
Link: https://lore.kernel.org/r/20220220031810.738362-19-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In mpi_set_phy_profile_req() and in pm8001_set_phy_profile_single(), if
pm8001_tag_alloc() fails to allocate a new tag, a warning message is issued
but the uninitialized tag variable is still used to build a command. Avoid
this by returning early in case of tag allocation failure.
Also make sure to always return the error code returned by
pm8001_tag_alloc() when this function fails instead of an arbitrary value.
Link: https://lore.kernel.org/r/20220220031810.738362-18-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCQ NON DATA is an NCQ command with the DMA_NONE DMA direction and so a
register-device-to-host-FIS response is expected for it.
However, for an IO_SUCCESS case, mpi_sata_completion() expects a
set-device-bits-FIS for any ata task with an use_ncq field true, which
includes NCQ NON DATA commands.
Fix this to correctly treat NCQ NON DATA commands as non-data by also
testing for the DMA_NONE DMA direction.
Link: https://lore.kernel.org/r/20220220031810.738362-16-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the pm8001_chip_sata_req() and pm80xx_chip_sata_req() functions, all
tasks with a DMA direction of DMA_NONE (no data transfer) are initialized
using the ATAP value 0x04. However, NCQ NON DATA commands, while being
DMA_NONE commands are NCQ commands and need to be initialized using the
value 0x07 for ATAP, similarly to other NCQ commands.
Make sure that NCQ NON DATA command tasks are initialized similarly to
other NCQ commands by also testing the task "use_ncq" field in addition to
the DMA direction. While at it, reorganize the code into a chain of if -
else if - else to avoid useless affectations and debug messages.
Link: https://lore.kernel.org/r/20220220031810.738362-15-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm8001_pci_resume(), the use of the u32 type for the local variable
device_state causes a sparse warning:
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype] device_state
got restricted pci_power_t [usertype] current_state
Since this variable is used only once in the function, remove it and use
pdev->current_state directly. While at it, also add a blank line after the
last local variable declaration.
Link: https://lore.kernel.org/r/20220220031810.738362-14-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In mpi_set_phy_profile_req() and pm8001_set_phy_profile_single(), use
cpu_to_le32() to initialize the ppc_phyid field of struct
set_phy_profile_req. Furthermore, fix the definition of the reserved field
of this structure to be an array of __le32, to match the use of
cpu_to_le32() when assigning values. These changes remove several sparse
type warnings.
Link: https://lore.kernel.org/r/20220220031810.738362-13-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that the __le32 fields of struct sata_cmd are manipulated after
applying the correct endian conversion. That is, use cpu_to_le32() for
assigning values and le32_to_cpu() for consulting a field value. In
particular, make sure that the calculations for the 4G boundary check are
done using CPU endianness and *not* little endian values. With these fixes,
many sparse warnings are removed.
While at it, fix some code identation and add blank lines after variable
declarations and in some other places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-12-damien.lemoal@opensource.wdc.com
Fixes: 0ecdf00ba6 ("[SCSI] pm80xx: 4G boundary fix.")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that the __le32 fields of struct ssp_ini_io_start_req are
manipulated after applying the correct endian conversion. That is, use
cpu_to_le32() for assigning values and le32_to_cpu() for consulting a field
value. In particular, make sure that the calculations for the 4G boundary
check are done using CPU endianness and *not* little endian values. With
these fixes, many sparse warnings are removed.
While at it, add blank lines after variable declarations and in some other
places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-11-damien.lemoal@opensource.wdc.com
Fixes: 0ecdf00ba6 ("[SCSI] pm80xx: 4G boundary fix.")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All fields of the kek_mgmt_req structure have the type __le32. So make sure
to use cpu_to_le32() to initialize them. This suppresses the sparse
warning:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [assigned] [usertype] new_curidx_ksop
got int
Link: https://lore.kernel.org/r/20220220031810.738362-10-damien.lemoal@opensource.wdc.com
Fixes: f5860992db ("[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All fields of the SASProtocolTimerConfig structure have the __le32 type.
As such, use cpu_to_le32() to initialize them. This change suppresses many
sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [usertype] pageCode
got int
Note that the check to limit the value of the STP_IDLE_TMO field is removed
as this field is initialized using the fixed (and small) value defined by
the STP_IDLE_TIME macro.
The pm8001_dbg() calls printing the values of the SASProtocolTimerConfig
structure fileds are changed to use le32_to_cpu() to present the values in
human readable form.
Link: https://lore.kernel.org/r/20220220031810.738362-9-damien.lemoal@opensource.wdc.com
Fixes: a6cb3d012b ("[SCSI] pm80xx: thermal, sas controller config and error handling update")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fields of the set_ctrl_cfg_req structure have the __le32 type, so use
cpu_to_le32() to assign them. This removes the sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32
got unsigned int
Link: https://lore.kernel.org/r/20220220031810.738362-8-damien.lemoal@opensource.wdc.com
Fixes: 842784e0d1 ("pm80xx: Update For Thermal Page Code")
Fixes: f5860992db ("[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files")
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ds_ads_m field of struct ssp_ini_tm_start_req has the type __le32.
Assigning a value to it should thus use cpu_to_le32(). This fixes the
sparse warning:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [assigned] [usertype] ds_ads_m
got int
Link: https://lore.kernel.org/r/20220220031810.738362-7-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The declaration of the local variable destination1 in pm80xx_pci_mem_copy()
as a pointer to a u32 results in the sparse warning:
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype]
got restricted __le32 [usertype]
Furthermore, the destination" argument of pm80xx_pci_mem_copy() is wrongly
declared with the const attribute.
Fix both problems by changing the type of the "destination" argument to
"__le32 *" and use this argument directly inside the pm80xx_pci_mem_copy()
function, thus removing the need for the destination1 local variable.
Link: https://lore.kernel.org/r/20220220031810.738362-6-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the sata_cmd struct is zeroed out before its fields are initialized,
there is no need for using "|=" to initialize the ncqtag_atap_dir_m
field. Using a standard assignment removes the sparse warning:
warning: invalid assignment: |=
Also, since the ncqtag_atap_dir_m field has type __le32, use cpu_to_le32()
to generate the assigned value.
Link: https://lore.kernel.org/r/20220220031810.738362-5-damien.lemoal@opensource.wdc.com
Fixes: c6b9ef5779 ("[SCSI] pm80xx: NCQ error handling changes")
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the type of partitionSizeTmp from u32 to __be32 to suppress the
sparse warning:
warning: cast to restricted __be32
Link: https://lore.kernel.org/r/20220220031810.738362-4-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid the sparse warning "warning: cast removes address space '__iomem' of
expression" by declaring the qp pointer as "u32 __iomem *". Accordingly,
change the accesses to the qp array to use readl().
Link: https://lore.kernel.org/r/20220220031810.738362-3-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To detect for the DMA_NONE (no data transfer) DMA direction,
sas_ata_qc_issue() tests if the command protocol is ATA_PROT_NODATA. This
test does not include the ATA_CMD_NCQ_NON_DATA command as this command
protocol is defined as ATA_PROT_NCQ_NODATA (equal to ATA_PROT_FLAG_NCQ) and
not as ATA_PROT_NODATA.
To include both NCQ and non-NCQ commands when testing for the DMA_NONE DMA
direction, use "!ata_is_data()".
Link: https://lore.kernel.org/r/20220220031810.738362-2-damien.lemoal@opensource.wdc.com
Fixes: 176ddd8917 ("scsi: libsas: Reset num_scatter if libata marks qc as NODATA")
Cc: stable@vger.kernel.org
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
Eliminate the follow coccicheck warnings:
./drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:1661:3-10: line 1661 is
redundant because platform_get_irq() already prints an error
./drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:1642:4-11: line 1642 is
redundant because platform_get_irq() already prints an error
./drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:1679:3-10: line 1679 is
redundant because platform_get_irq() already prints an error
Link: https://lore.kernel.org/r/20220215020524.44268-1-yang.lee@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are no more end-users of REQ_OP_WRITE_SAME left, so we can start
deleting it.
Link: https://lore.kernel.org/r/20220209082828.2629273-5-hch@lst.de
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The write_same and write_zeroes limits for SCSI are effectively the same,
so the current code works just fine. But we plan to remove
REQ_OP_WRITE_SAME support, so switch to querying the write zeroes limit for
a zeroing WRITE SAME operation.
Link: https://lore.kernel.org/r/20220209082828.2629273-2-hch@lst.de
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warning by not allocating driver's event handling worker
queue with WQ_MEM_RECLAIM flag enabled:
workqueue: WQ_MEM_RECLAIM
mpi3mr_fwevt_worker [mpi3mr] is flushing !WQ_MEM_RECLAIM events
Link: https://lore.kernel.org/r/20220218180515.27455-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make q_dev_state a little more readable and maintainable by using named
initializers.
Also convert QLA8XXX_DEV_* macros into an enum and remove
qla83xx_dev_state_to_string(), which is a duplicate of qdev_state().
Link: https://lore.kernel.org/r/AS8PR10MB495298515A7553C8D6D6E74D9D349@AS8PR10MB4952.EURPRD10.PROD.OUTLOOK.COM
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Gleb Chesnokov <Chesnokov.G@raidix.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make port_state_str and port_dstate_str a little more readable and
maintainable by using named initializers.
Also convert FCS_* macros into an enum.
Link: https://lore.kernel.org/r/AS8PR10MB495215841EB25C16DBC0CB409D349@AS8PR10MB4952.EURPRD10.PROD.OUTLOOK.COM
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Gleb Chesnokov <Chesnokov.G@raidix.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit edc0596cc0 ("scsi: ufs: core: Stop clearing UNIT ATTENTIONS")
removed all callers of wlun_dev_to_hba(). Hence also remove the macro
itself.
Link: https://lore.kernel.org/r/1891546521.01644927481711.JavaMail.epsvc@epcpadp4
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-49-bvanassche@acm.org
Cc: Helge Deller <deller@gmx.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-48-bvanassche@acm.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the DMA handle into the per-command private data instead of using the
SCSI pointer from struct scsi_cmnd. This patch prepares for removal of the
SCSI pointer from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-47-bvanassche@acm.org
Cc: Ondrej Zary <linux@zary.sk>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-45-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-44-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of using the SCp.ptr field to track whether or not a command is
in flight, use the sp->type field to track this information. sp->type
must be set for proper operation of the qla2xxx driver. See e.g. the
switch (sp->type) statement in qla2x00_ct_entry().
This patch prepares for removal of the SCSI pointer from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-43-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-42-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-41-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd.
This patch prepares for removal of the SCSI pointer from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-40-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
in struct scsi_cmnd.
This patch prepares for removal of the SCSI pointer from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-39-bvanassche@acm.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the SCSI status field to private data. Stop setting the .ptr,
.this_residual, .buffer and .buffer_residual SCSI pointer members
since no code in this driver reads these members.
This patch prepares for removal of the SCSI pointer from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-38-bvanassche@acm.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Masanori Goto <gotom@debian.or.jp>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-37-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following compiler warning:
drivers/scsi/mvsas/mv_init.c: In function ‘mvs_pci_init’:
drivers/scsi/mvsas/mv_init.c:497:30: warning: variable ‘mpi’ set but not used [-Wunused-but-set-variable]
497 | struct mvs_prv_info *mpi;
| ^~~
Link: https://lore.kernel.org/r/20220218195117.25689-36-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-35-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-34-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-33-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-32-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following compiler warning:
drivers/scsi/mac53c94.c: In function 'mac53c94_init':
drivers/scsi/mac53c94.c:128:13: warning: variable 'x' set but not used [-Wunused-but-set-variable]
128 | int x;
Link: https://lore.kernel.org/r/20220218195117.25689-31-bvanassche@acm.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. Remove the CMD_SCSI_STATUS() assignment because the
assigned value is not used.
This patch prepares for removal of the SCSI pointer from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-30-bvanassche@acm.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. Remove the CMD_SCSI_STATUS() assignment because the
assigned value is not used.
This patch prepares for removal of the SCSI pointer from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-29-bvanassche@acm.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the fc_fcp_pkt pointer, the residual length and the SCSI status into
the new data structure libfc_cmd_priv. This patch prepares for removal of
the SCSI pointer from struct scsi_cmnd.
The user of the libfc data path functions have been identified as follows:
$ git grep -lw fc_queuecommand | grep -v scsi/libfc/
drivers/scsi/fcoe/fcoe.c
Link: https://lore.kernel.org/r/20220218195117.25689-28-bvanassche@acm.org
Cc: Saurav Kashyap <skashyap@marvell.com>
Cc: Javed Hasan <jhasan@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-27-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of storing the iSCSI task pointer and the session age in the SCSI
pointer, use command-private variables. This patch prepares for removal of
the SCSI pointer from struct scsi_cmnd.
The list of iSCSI drivers has been obtained as follows:
$ git grep -lw iscsi_host_alloc
drivers/infiniband/ulp/iser/iscsi_iser.c
drivers/scsi/be2iscsi/be_main.c
drivers/scsi/bnx2i/bnx2i_iscsi.c
drivers/scsi/cxgbi/libcxgbi.c
drivers/scsi/iscsi_tcp.c
drivers/scsi/libiscsi.c
drivers/scsi/qedi/qedi_main.c
drivers/scsi/qla4xxx/ql4_os.c
include/scsi/libiscsi.h
Note: it is not clear to me how the qla4xxx driver can work without this
patch since it uses the scsi_cmnd::SCp.ptr member for two different
purposes:
- The qla4xxx driver uses this member to store a struct srb pointer.
- libiscsi uses this member to store a struct iscsi_task pointer.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Manish Rangankar <mrangankar@marvell.com>
Cc: Karen Xie <kxie@chelsio.com>
Cc: Ketan Mukadam <ketan.mukadam@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
iscsi
Link: https://lore.kernel.org/r/20220218195117.25689-26-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer.
This patch prepares for removal of the SCSI pointer from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-25-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Rename hpt_scsi_pointer into hpt_cmd_priv because that data structure is
not related to struct scsi_pointer.
Link: https://lore.kernel.org/r/20220218195117.25689-24-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-23-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Report both the command flags and command state instead of only the
command state.
Link: https://lore.kernel.org/r/20220218195117.25689-22-bvanassche@acm.org
Fixes: 4d7007b49d ("[SCSI] fnic: Fnic Trace Utility")
Cc: Hiral Patel <hiralpat@cisco.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-21-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-20-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the code that sets SCSI pointer members since there is no code in
this driver that reads these members.
Link: https://lore.kernel.org/r/20220218195117.25689-19-bvanassche@acm.org
Cc: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-18-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-17-bvanassche@acm.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-16-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following W=1 warning:
drivers/scsi/aha1542.c:209:12: warning: variable ‘inquiry_result’ set but not used [-Wunused-but-set-variable]
209 | u8 inquiry_result[4];
Link: https://lore.kernel.org/r/20220218195117.25689-15-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-14-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-13-bvanassche@acm.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
None of the 53c700 drivers uses the SCSI pointer. Hence remove the code
from 53c700.c that clears two SCSI pointer fields. The 53c700 drivers are:
$ git grep -l 'include.*53c700'
drivers/scsi/53c700.c
drivers/scsi/a4000t.c
drivers/scsi/bvme6000_scsi.c
drivers/scsi/lasi700.c
drivers/scsi/mvme16x_scsi.c
drivers/scsi/sim710.c
drivers/scsi/sni_53c710.c
drivers/scsi/zorro7xx.c
Link: https://lore.kernel.org/r/20220218195117.25689-12-bvanassche@acm.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set .cmd_size in the SCSI host template instead of using the SCSI pointer
from struct scsi_cmnd. This patch prepares for removal of the SCSI pointer
from struct scsi_cmnd. The ARM SCSI drivers have been identified as follows:
$ git grep -l '#include.*arm_scsi.h'
drivers/scsi/arm/acornscsi.c
drivers/scsi/arm/cumana_2.c
drivers/scsi/arm/eesox.c
drivers/scsi/arm/fas216.c
drivers/scsi/arm/powertec.c
Link: https://lore.kernel.org/r/20220218195117.25689-11-bvanassche@acm.org
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The new name makes the purpose of this header file more clear and also
makes it easier to find this header file with grep.
Link: https://lore.kernel.org/r/20220218195117.25689-10-bvanassche@acm.org
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is necessary for the eventual removal of SCp from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-9-bvanassche@acm.org
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Ondrej Zary <linux@zary.sk>
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This makes it easier to find users of the NCR5380_cmd data structure with
'grep'.
Link: https://lore.kernel.org/r/20220218195117.25689-8-bvanassche@acm.org
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following two header files have the same file name: include/scsi/scsi.h
and drivers/scsi/scsi.h. This is confusing. Remove the latter since the
following note was added in drivers/scsi/scsi.h in 2004:
"NOTE: this file only contains compatibility glue for old drivers. All
these wrappers will be removed sooner or later. For new code please use
the interfaces declared in the headers in include/scsi/"
Link: https://lore.kernel.org/r/20220218195117.25689-7-bvanassche@acm.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch prepares for removal of the drivers/scsi/scsi.h header file. That
header file defines the 'TRUE' and 'FALSE' constants.
Link: https://lore.kernel.org/r/20220218195117.25689-6-bvanassche@acm.org
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
nsp_reselected() and nsphw_init() always return TRUE. Change the return type
of these functions into 'void'.
Link: https://lore.kernel.org/r/20220218195117.25689-5-bvanassche@acm.org
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch prepares for removal of the drivers/scsi/scsi.h header file.
That header file defines the 'TRUE' and 'FALSE' constants.
Link: https://lore.kernel.org/r/20220218195117.25689-4-bvanassche@acm.org
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ips_release() has one caller and that caller ignores the value returned by
ips_release(). Hence change the return type of that function into 'void'.
Link: https://lore.kernel.org/r/20220218195117.25689-3-bvanassche@acm.org
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whether or not CONFIG_BUG is enabled, BUG() never returns. Hence, code past
a BUG() statement is unreachable. Remove one such unreachable statement.
Link: https://lore.kernel.org/r/20220218195117.25689-2-bvanassche@acm.org
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a function to execute an ATA command using the TMF code, and use in the
hisi_sas driver. That driver needs to be able to issue the command on a
specific phy, so add an interface for that.
With that, hisi_sas_exec_internal_tmf_task() may be deleted.
Link: https://lore.kernel.org/r/1645534259-27068-19-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a generic implementation of abort task TMF handler, and use in LLDDs.
With that, some LLDDs custom TMF functions can now be deleted.
Link: https://lore.kernel.org/r/1645112566-115804-18-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a generic implementation of query task TMF handler, and use in LLDDs.
Link: https://lore.kernel.org/r/1645112566-115804-17-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a generic implementation of LU reset TMF handler, and use in LLDDs.
Link: https://lore.kernel.org/r/1645112566-115804-16-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a generic implementation of clear task set TMF handler, and use in
LLDDs.
Link: https://lore.kernel.org/r/1645112566-115804-15-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a generic implementation of abort task set TMF handler, and use in
LLDDs.
Link: https://lore.kernel.org/r/1645112566-115804-14-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hisi_sas and pm8001 TMF handlers have some special processing for when
the TMF is aborted, so add a callback and fill it in for those drivers.
Link: https://lore.kernel.org/r/1645112566-115804-13-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pm8001 TMF handler has some special processing when the TMF completes,
so add a callback and fill it in for the pm8001 driver.
Link: https://lore.kernel.org/r/1645112566-115804-12-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a function to issue an SSP TMF.
Add a temp prototype to keep make W=1 happy.
Link: https://lore.kernel.org/r/1645112566-115804-11-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drivers using libsas have to issue their own TMFs, and the code to do this
is duplicated between drivers.
Add a common function to handle TMFs. This will be also used for sending
ATA commands, but use name "tmf" as the purpose is similar between SCSI and
ATA in the usage.
The force_phy_id argument will be used for a hisi_sas HW bug workaround.
We check the sas task status stat field against TMF codes, as according to
the SAS v1.1 spec 9.2.2.5.3, if response_data is in datapres, then the
response code should be a TMF code - see table 128.
Link: https://lore.kernel.org/r/1645112566-115804-10-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a pointer to a sas_tmf_task to the sas_task struct, as this will be
used when the common LLDD TMF code is factored out.
Also set it for the LLDDs to store per-sas_task TMF info.
Link: https://lore.kernel.org/r/1645112566-115804-9-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some of the LLDDs which use libsas have their own definition of a struct
to hold TMF info, so add a common struct for libsas.
Also add an interim force phy id field for hisi_sas driver, which will be
removed once the STP "TMF" code is factored out.
Even though some LLDDs (pm8001) use a u32 for the tag, u16 will be adequate,
as that named driver only uses tags in range [0, 1024).
Link: https://lore.kernel.org/r/1645112566-115804-8-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the SMP task handlers to the core host code as they will be re-used
for executing internal abort and TMF tasks.
Link: https://lore.kernel.org/r/1645112566-115804-7-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no user, so delete it.
Link: https://lore.kernel.org/r/1645112566-115804-6-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
