replace calls that read this capability with accesses to ath9k_hw's
regulatory data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.
The old ANI implementation is left intact.
Details of the new ANI implemention:
* ANI adjustment logic is now table driven so that each ANI level
setting is parameterized. This makes adjustments much more
deterministic than the old procedure based logic and allows
adjustments to be made incrementally to several parameters per
level.
* ANI register settings are now relative to INI values; so ANI
param zero level == INI value. Appropriate floor and ceiling
values are obeyed when adjustments are combined with INI values.
* ANI processing is done once per second rather that every 100ms.
The poll interval is now a set upon hardware initialization and
can be picked up by the core driver.
* OFDM error and CCK error processing are made in a round robin
fashion rather than allowing all OFDM adjustments to be made
before CCK adjustments.
* ANI adjusts MRC CCK off in the presence of high CCK errors
* When adjusting spur immunity (SI) and OFDM weak signal detection,
ANI now sets register values for the extension channel too
* When adjusting FIR step (ST), ANI now sets register for FIR step
low too
* FIR step adjustments now allow for an extra level of immunity for
extremely noisy environments
* The old Noise immunity setting (NI), which changes coarse low, size
desired, etc have been removed. Changing these settings could affect
up RIFS RX as well.
* CCK weak signal adjustment is no longer used
* ANI no longer enables phy error interrupts; in all cases phy hw
counting registers are used instead
* The phy error count (overflow) interrupts are also no longer used
for ANI adjustments. All ANI adjustments are made via the polling
routine and no adjustments are possible in the ISR context anymore
* A history settings buffer is now correctly used for each channel;
channel settings are initialized with the defaults but later
changes are restored when returning back to that channel
* When scanning, ANI is disabled settings are returned to (INI) defaults.
* OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
low/high water marks, providing increased stability/hysteresis when
changing levels.
* Similarly CCK phy error thresholds are now 300 & 600 (errors/second)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because there is a limited number of tx buffers available, once the
queue has been filled to a certain point, ath9k needs to stop accepting
new frames from mac80211. In order to prevent a full WMM queue from
stopping another queue with fewer frames, this patch limits the number
of queued frames to a quarter of the total available tx buffers, minus
some reserved frames to be used for other purposes (e.g. beacons).
Because tx buffers are reserved for frames when they're staged in
software queues as well, the actual queue depth cannot be used for
this, so this patch stores a reference to the tx queue in the ath_buf
struct and keeps track of the total number of pending frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx should not be disabed/disabled when hw supports auto sleeping.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables the baseband watchdog events for the AR9003
family on ath9k. Upon an a baseband watchdog interrupt we reset
the hardware, this should address corner case conditions where
normal operation can stall. Enable ATH_DBG_RESET to be able
to review details of the bb watchdog interrupt once it happens.
If you're curious how often this happens just grep the debugfs
interrupt file.
Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.
The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.
It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.
I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.
Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.
Signed-off-by: Daniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ah variable in the functions that didn't have it and used sc->imask.
Replace sc->sc_ah with ah in those functions.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts ath9k to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If split tkip key is used, ath_delete_key should delete
rx key and rx mic key. This patch fixes the leak of hw
keycache in the case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM timer interrupt is enabled even before the ACK of nullqos
is received which is unnecessary.
Also clean up the CONF_PS part of config callback properly for
better readability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Numeric channel is hard to get, so it won't be printed. Replace Mhz
with MHz on the affected lines and add commas as needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IDLE PS (Full Sleep) doesn't work when ifconfig up
is done during Idle unassociated state.
Fix this by restoring FULL SLEEP in ps_restore if CONF_IDLE
is set.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cleaning up beacon buffers and slots, ath9k currently checks if
sc->ah->opmode is set to a beacon related mode before cleaning up
buffers.
An unfortunate ordering of interface up/down commands can lead to
sc->ah->opmode being set to monitor mode, while there are AP interfaces
present on the same wiphy.
Always cleaning up beacon buffers if present fixes this issue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users wishing to tweak tx power want it to happen immediately,
try to respect that. This was tested by Lorenzo by measuring the
received signal strength from an AP with ath9k and the patch.
Changing the tx power on the AP produced these results:
1) iwconfig wlan0 txpower 20 ---> Rx power -37dbm
2) iwconfig wlan0 txpower 15 ---> Rx power -41dbm
3) iwconfig wlan0 txpower 10 ---> Rx power -45dbm
4) iwconfig wlan0 txpower 5 ---> Rx power -51dbm
5) iwconfig wlan0 txpower 0 ---> Rx power -37dbm
The result with 0 is an anomoly and would need to be
addressed through a separate patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously ath9k left the initialization of slot timing and ACK/CTS
timeout to the mode specific initvals. This does not handle short vs
long slot in 2.4 GHz and uses a rather strange value for the 2.4 GHz
ACK timeout (64 usec).
This patch uses the proper ath9k_hw functions for setting slot time and
timeouts and also implements the switch between short and long slot
time in 2.4 GHz
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 passes appropriate flags indicating whether
monitor mode is being used. Use this to set the HW opmode.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX queues have to be stopped during an
internal reset. Not handling this would result
in packet loss - fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sc_flags has slowly become a kitchen sink over time.
Move powersave related flags to a separate variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move initialization/de-initialization related
code to this file.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all LED/RFKILL/BTCOEX related code
to gpio.c
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The newer single chip hardware family of chipsets have not been
experiencing issues with power saving set by default with recent
fixes merged (even into stable). The remaining issues are only
reported with AR5416 and since enabling PS by default can increase
power savings considerably best to take advantage of that feature
as this has been tested properly.
For more details on this issue see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=14267
We leave AR5416 with PS disabled by default, that seems to require
some more work.
Cc: stable@kernel.org
Cc: Peter Stuge <peter@stuge.se>
Cc: Justin P. Mattock <justinmattock@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMDPDU actions poke hardware for TX operation, as such
we want to turn hardware on for these actions. AMDPU RX operations
do not require hardware on as nothing is done in hardware for
those actions. Without this we cannot guarantee hardware has
been programmed correctly for each AMPDU TX action.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove a IBSS/AP/Mesh interface we stop DMA
but to do this we should ensure hardware is on. Awaken
the device prior to these calls. This should ensure
DMA is stopped upon suspend and plain device removal.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure the device is awake prior to trying to tell hardware
to stop it. Impact of not doing this is we can likely leave
the device in an undefined state likely causing issues with
suspend and resume. This patch ensures harware is where it
should be prior to suspend.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable the TX hang monitoring routine when doing a scan.
Monitoring for a hung situation is not really necessary during
a scan run.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cancel/restart the ANI timer directly.
With this patch, the ANI lock can be removed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIB counters are disabled when doing a chip reset.
Since ANI depends on the MIB registers for its operation, relying
on the contents of said registers during HW reset results in sub-optimal
performance.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the 2GHz band is enabled unconditionally, even if the device
does not support it.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the beacon queue parameters with best effort queue parameters for
IBSS mode. This reduces the number of beacons generated by ath9k and
ensures a fair beacon distribution when there are multiple IBSS stations.
Also CWmin is quadrupled to achieve the expected percentage of
distribution.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Software padding is done on the TX path and software unpadding is done on the
RX path. This patch corrects the position where the padding occurs. A specific
function computes the pad position and this function is used in the TX and RX
path. This patch has been tested by generating every possible 802.11 frames
with every possible frame_control field and a varying length. This patch is
useful for analyzing non standard 802.11 frames going over the air
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 was telling us to go into Powersave we listened
and immediately turned RX off. This meant hardware would not
see the ACKs from the AP we're associated with and hardware
we'd end up retransmiting the null data frame in a loop
helplessly.
Fix this by keeping track of the transmitted nullfunc frames
and only when we are sure the AP has sent back an ACK do we
go ahead and shut RX off.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Vivek Natarajan <Vivek.Natarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes ath9k to pass proper MCS indexes and flags
between the RC and the rest of the driver code.
sc->cur_rate_table remains, as it's used by the RC code internally,
but the rest of the driver code no longer uses it, so a potential
new RC for ath9k would not have to update it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
