The "virtio_mmio.device=" command line argument allows a user to specify
the size, address, and IRQ of a virtio device. Previously the only
requirement for the IRQ was that it be an unsigned integer.
Zero is an unsigned integer but an invalid IRQ number, and after
a85a6c86c2 ("driver core: platform: Clarify that IRQ 0 is invalid"),
attempts to use IRQ 0 cause warnings.
If the user specifies IRQ 0, return failure instead of registering a device
with IRQ 0.
Fixes: a85a6c86c2 ("driver core: platform: Clarify that IRQ 0 is invalid")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
The device may be torn down, but the domain should still be valid. Lets
use that as the tlb flush ops cookie.
Fixes a problem reported in [1]
[1] https://lkml.org/lkml/2020/7/20/104
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 09b5dfff9a ("iommu/qcom: Use accessor functions for iommu private data")
Link: https://lore.kernel.org/r/20200720155217.274994-1-robdclark@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In pfkey_dump() dplen and splen can both be specified to access the
xfrm_address_t structure out of bounds in__xfrm_state_filter_match()
when it calls addr_match() with the indexes. Return EINVAL if either
are out of range.
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-team@android.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
My colleague Codrin Ciubotariu, now, maintains this driver internally.
Then I handover the mainline maintenance to him.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There are few issues on Zynq SOC observed in the stress tests causing
timeout errors. Even though all the data is received, timeout error
is thrown. This is due to an IP bug in which the COMP bit in ISR is
not set at end of transfer and completion interrupt is not generated.
This bug is seen on Zynq platforms when the following condition occurs:
Master read & HOLD bit set & Transfer size register reaches '0'.
One workaround is to clear the HOLD bit before the transfer size
register reaches '0'. The current implementation checks for this at
the start of the loop and also only for less than FIFO DEPTH case
(ignoring the equal to case).
So clear the HOLD bit when the data yet to receive is less than or
equal to the FIFO DEPTH. This avoids the IP bug condition.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit d358def706.
There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As expected, this requires the same quirk as the SSL2+ in order for the
clock to sync. This was suggested by, and tested on an SSL2, by Dmitry.
Suggested-by: Dmitry <dpavlushko@gmail.com>
Signed-off-by: Laurence Tratt <laurie@tratt.net>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200621075005.52mjjfc6dtdjnr3h@overdrive.tratt.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is apparently one site that violates the rule that only current
and ttwu() will modify task->state, namely ptrace_{,un}freeze_traced()
will change task->state for a remote task.
Oleg explains:
"TASK_TRACED/TASK_STOPPED was always protected by siglock. In
particular, ttwu(__TASK_TRACED) must be always called with siglock
held. That is why ptrace_freeze_traced() assumes it can safely do
s/TASK_TRACED/__TASK_TRACED/ under spin_lock(siglock)."
This breaks the ordering scheme introduced by commit:
dbfb089d36 ("sched: Fix loadavg accounting race")
Specifically, the reload not matching no longer implies we don't have
to block.
Simply things by noting that what we need is a LOAD->STORE ordering
and this can be provided by a control dependency.
So replace:
prev_state = prev->state;
raw_spin_lock(&rq->lock);
smp_mb__after_spinlock(); /* SMP-MB */
if (... && prev_state && prev_state == prev->state)
deactivate_task();
with:
prev_state = prev->state;
if (... && prev_state) /* CTRL-DEP */
deactivate_task();
Since that already implies the 'prev->state' load must be complete
before allowing the 'prev->on_rq = 0' store to become visible.
Fixes: dbfb089d36 ("sched: Fix loadavg accounting race")
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Christian Brauner <christian.brauner@ubuntu.com>
On x86-32 the idt_table with 256 entries needs only 2048 bytes. It is
page-aligned, but the end of the .bss..page_aligned section is not
guaranteed to be page-aligned.
As a result, objects from other .bss sections may end up on the same 4k
page as the idt_table, and will accidentially get mapped read-only during
boot, causing unexpected page-faults when the kernel writes to them.
This could be worked around by making the objects in the page aligned
sections page sized, but that's wrong.
Explicit sections which store only page aligned objects have an implicit
guarantee that the object is alone in the page in which it is placed. That
works for all objects except the last one. That's inconsistent.
Enforcing page sized objects for these sections would wreckage memory
sanitizers, because the object becomes artificially larger than it should
be and out of bound access becomes legit.
Align the end of the .bss..page_aligned and .data..page_aligned section on
page-size so all objects places in these sections are guaranteed to have
their own page.
[ tglx: Amended changelog ]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200721093448.10417-1-joro@8bytes.org
Currently drive supports taprio offload which is a tc feature offloaded
to cpsw hardware. So driver has to set the hw feature flag, NETIF_F_HW_TC
in the net device to be compliant. This patch adds the flag.
Fixes: 8127224c27 ("ethernet: ti: am65-cpsw-qos: add TAPRIO offload support")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When regmap_update_bits failed in ave_init(), calls of the functions
reset_control_assert() and clk_disable_unprepare() were missed.
Add goto out_reset_assert to do this.
Fixes: 57878f2f46 ("net: ethernet: ave: add support for phy-mode setting of system controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is not working because of problems of its receiving code.
This patch fixes it to make it work.
When the driver receives an LAPB frame, it should first pass the frame
to the LAPB module to process. After processing, the LAPB module passes
the data (the packet) back to the driver, the driver should then add a
one-byte pseudo header and pass the data to upper layers.
The changes to the "x25_asy_bump" function and the
"x25_asy_data_indication" function are to correctly implement this
procedure.
Also, the "x25_asy_unesc" function ignores any frame that is shorter
than 3 bytes. However the shortest frames are 2-byte long. So we need
to change it to allow 2-byte frames to pass.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Reviewed-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sync_thread_backup only checks sk_receive_queue is empty or not,
there is a situation which cannot sync the connection entries when
sk_receive_queue is empty and sk_rmem_alloc is larger than sk_rcvbuf,
the sync packets are dropped in __udp_enqueue_schedule_skb, this is
because the packets in reader_queue is not read, so the rmem is
not reclaimed.
Here I add the check of whether the reader_queue of the udp sock is
empty or not to solve this problem.
Fixes: 2276f58ac5 ("udp: use a separate rx queue for packet reception")
Reported-by: zhouxudong <zhouxudong8@huawei.com>
Signed-off-by: guodeqing <geffrey.guo@huawei.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
According to 'man 8 ip-netns', if `ip netns identify` returns an empty string,
there's no net namespace associated with current PID: fix the net ns entrance
logic.
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Lobakin says:
====================
qed: suppress irrelevant error messages on HW init
This raises the verbosity level of several error/warning messages on
driver/module initialization, most of which are false-positives, and
the one actively spamming the log for no reason.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It was found that qed_pglueb_rbc_attn_handler() can produce a lot of
false-positive error detections on driver load/reload (especially after
crashes/recoveries) and spam the kernel log:
[ 4.958275] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d00ff0
[ 2079.146764] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[ 2116.374631] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[ 2135.250564] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[...]
Reduce the logging level of two false-positive prone error messages from
notice to verbose on initialization (only) to not mix it with real error
attentions while debugging.
Fixes: 666db4862f ("qed: Revise load sequence to avoid PCI errors")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the verbosity of the "don't support RoCE & iWARP simultaneously"
warning to debug level to stop flooding on driver/hardware initialization:
[ 4.783230] qede 01:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth0]
[ 4.810020] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 4.861186] qede 01:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth1]
[ 4.893311] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.181713] qede a1:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth2]
[ 5.224740] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.276449] qede a1:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth3]
[ 5.318671] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.369548] qede a1:00.02: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth4]
[ 5.411645] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
Fixes: e0a8f9de16 ("qed: Add iWARP enablement support")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the nsim_create(), rtnl_lock() is called before nsim_bpf_init().
If nsim_bpf_init() is failed, rtnl_unlock() should be called,
but it isn't called.
So, unbalanced locking would occur.
Fixes: e05b2d141f ("netdevsim: move netdev creation/destruction to dev probe")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing "ip link set dev ... up" for a ksz9477 backed link,
ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove
1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is
called. Doing so reverts any previous change to advertised link modes
e.g. using a udevd .link file.
phy_remove_link_mode is not meant to be used while opening a link and
should be called during phy probe when the link is not yet available to
userspace.
Therefore move the phy_remove_link_mode calls into
ksz9477_switch_register. It indirectly calls dsa_register_switch, which
creates the relevant struct phy_devices and we update the link modes
right after that. At that time dev->features is already initialized by
ksz9477_switch_detect.
Remove phy_setup from ksz_dev_ops as no users remain.
Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/
Fixes: 42fc6a4c61 ("net: dsa: microchip: prepare PHY for proper advertisement")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: fixes for -net
There are some bugfixes for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, PF queries the MAC link status per second by calling
function hclge_get_mac_link_status(). It return the error code
when failed to send cmdq command to firmware. It's incorrect,
because this return value is used as the MAC link status, which
0 means link down, and none-zero means link up. So fixes it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The content of the TX desc is automatically cleared by the HW
when the HW has sent out the packet to the wire. When desc filling
fails in hns3_nic_net_xmit(), it will call hns3_clear_desc() to do
the error handling, which miss zeroing of the TX desc and the
checking if a unmapping is needed.
So add the zeroing and checking in hns3_clear_desc() to avoid the
above problem. Also add DESC_TYPE_UNKNOWN to indicate the info in
desc_cb is not valid, because hns3_nic_reclaim_desc() may treat
the desc_cb->type of zero as packet and add to the sent pkt
statistics accordingly.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With GRO and fraglist support, the SKB can be aggregated to
a total size of 65535, and when that SKB is forwarded through
a bridge, the size of the SKB may be pushed to exceed the size
of 65535 when br_dev_queue_push_xmit() is called.
The max send size of BD supported by the HW is 65535, when a SKB
with a headlen of over 65535 is sent to the driver, the driver
needs to use multi BD to send the linear data, and the send size
of the last BD is calculated incorrectly by the driver who is
using '&' operation, which causes a TX error.
Use '%' operation to fix this problem.
Fixes: 3fe13ed95d ("net: hns3: avoid mult + div op in critical data path")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a big TX buffer is sent using multi BD, the driver maps the
whole TX buffer, and unmaps it using info in desc_cb corresponding
to each BD, but only the info in the desc_cb of first BD is correct,
other info in desc_cb is wrong, which causes TX unmapping problem
when SMMU is on.
Only set the mapping and freeing info in the desc_cb of first BD to
fix this problem, because the TX buffer only need to be unmapped and
freed once.
Fixes: 1e8a7977d09f("net: hns3: add handling for big TX fragment")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huzhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't use IS_UDPLITE to replace udp_sk->pcflag when UDPLITE_RECV_CC is
checked.
Fixes: b2bf1e2659 ("[UDP]: Clean up for IS_UDPLITE macro")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I cat 'tx_timeout' by sysfs, it displays as follows. It's better to
add a newline for easy reading.
root@syzkaller:~# cat /sys/devices/virtual/net/lo/queues/tx-0/tx_timeout
0root@syzkaller:~#
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the report of [1], this driver is possible to cause
the following error in ravb_tx_timeout_work().
ravb e6800000.ethernet ethernet: failed to switch device to config mode
This error means that the hardware could not change the state
from "Operation" to "Configuration" while some tx and/or rx queue
are operating. After that, ravb_config() in ravb_dmac_init() will fail,
and then any descriptors will be not allocaled anymore so that NULL
pointer dereference happens after that on ravb_start_xmit().
To fix the issue, the ravb_tx_timeout_work() should check
the return values of ravb_stop_dma() and ravb_dmac_init().
If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX
and just exits. If ravb_dmac_init() fails, just exits.
[1]
https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima says:
====================
udp: Fix reuseport selection with connected sockets.
This patch set addresses two issues which happen when both connected and
unconnected sockets are in the same UDP reuseport group.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, SO_REUSEPORT does not work well if connected sockets are in a
UDP reuseport group.
Then reuseport_has_conns() returns true and the result of
reuseport_select_sock() is discarded. Also, unconnected sockets have the
same score, hence only does the first unconnected socket in udp_hslot
always receive all packets sent to unconnected sockets.
So, the result of reuseport_select_sock() should be used for load
balancing.
The noteworthy point is that the unconnected sockets placed after
connected sockets in sock_reuseport.socks will receive more packets than
others because of the algorithm in reuseport_select_sock().
index | connected | reciprocal_scale | result
---------------------------------------------
0 | no | 20% | 40%
1 | no | 20% | 20%
2 | yes | 20% | 0%
3 | no | 20% | 40%
4 | yes | 20% | 0%
If most of the sockets are connected, this can be a problem, but it still
works better than now.
Fixes: acdcecc612 ("udp: correct reuseport selection with connected sockets")
CC: Willem de Bruijn <willemb@google.com>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an unconnected socket in a UDP reuseport group connect()s, has_conns is
set to 1. Then, when a packet is received, udp[46]_lib_lookup2() scans all
sockets in udp_hslot looking for the connected socket with the highest
score.
However, when the number of sockets bound to the port exceeds max_socks,
reuseport_grow() resets has_conns to 0. It can cause udp[46]_lib_lookup2()
to return without scanning all sockets, resulting in that packets sent to
connected sockets may be distributed to unconnected sockets.
Therefore, reuseport_grow() should copy has_conns.
Fixes: acdcecc612 ("udp: correct reuseport selection with connected sockets")
CC: Willem de Bruijn <willemb@google.com>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to cause a btrfs mount to fail by racing it with a slow
umount. The crux of the sequence is generic_shutdown_super not yet
calling sop->put_super before btrfs_mount_root calls btrfs_open_devices.
If that occurs, btrfs_open_devices will decide the opened counter is
non-zero, increment it, and skip resetting fs_devices->total_rw_bytes to
0. From here, mount will call sget which will result in grab_super
trying to take the super block umount semaphore. That semaphore will be
held by the slow umount, so mount will block. Before up-ing the
semaphore, umount will delete the super block, resulting in mount's sget
reliably allocating a new one, which causes the mount path to dutifully
fill it out, and increment total_rw_bytes a second time, which causes
the mount to fail, as we see double the expected bytes.
Here is the sequence laid out in greater detail:
CPU0 CPU1
down_write sb->s_umount
btrfs_kill_super
kill_anon_super(sb)
generic_shutdown_super(sb);
shrink_dcache_for_umount(sb);
sync_filesystem(sb);
evict_inodes(sb); // SLOW
btrfs_mount_root
btrfs_scan_one_device
fs_devices = device->fs_devices
fs_info->fs_devices = fs_devices
// fs_devices-opened makes this a no-op
btrfs_open_devices(fs_devices, mode, fs_type)
s = sget(fs_type, test, set, flags, fs_info);
find sb in s_instances
grab_super(sb);
down_write(&s->s_umount); // blocks
sop->put_super(sb)
// sb->fs_devices->opened == 2; no-op
spin_lock(&sb_lock);
hlist_del_init(&sb->s_instances);
spin_unlock(&sb_lock);
up_write(&sb->s_umount);
return 0;
retry lookup
don't find sb in s_instances (deleted by CPU0)
s = alloc_super
return s;
btrfs_fill_super(s, fs_devices, data)
open_ctree // fs_devices total_rw_bytes improperly set!
btrfs_read_chunk_tree
read_one_dev // increment total_rw_bytes again!!
super_total_bytes < fs_devices->total_rw_bytes // ERROR!!!
To fix this, we clear total_rw_bytes from within btrfs_read_chunk_tree
before the calls to read_one_dev, while holding the sb umount semaphore
and the uuid mutex.
To reproduce, it is sufficient to dirty a decent number of inodes, then
quickly umount and mount.
for i in $(seq 0 500)
do
dd if=/dev/zero of="/mnt/foo/$i" bs=1M count=1
done
umount /mnt/foo&
mount /mnt/foo
does the trick for me.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Boris Burkov <boris@bur.io>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When locking pages for delalloc, we check if it's dirty and mapping still
matches. If it does not match, we need to return -EAGAIN and release all
pages. Only the current page was put though, iterate over all the
remaining pages too.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Robbie Ko <robbieko@synology.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
When running tests like generic/013 on test device with btrfs quota
enabled, it can normally lead to data leak, detected at unmount time:
BTRFS warning (device dm-3): qgroup 0/5 has unreleased space, type 0 rsv 4096
------------[ cut here ]------------
WARNING: CPU: 11 PID: 16386 at fs/btrfs/disk-io.c:4142 close_ctree+0x1dc/0x323 [btrfs]
RIP: 0010:close_ctree+0x1dc/0x323 [btrfs]
Call Trace:
btrfs_put_super+0x15/0x17 [btrfs]
generic_shutdown_super+0x72/0x110
kill_anon_super+0x18/0x30
btrfs_kill_super+0x17/0x30 [btrfs]
deactivate_locked_super+0x3b/0xa0
deactivate_super+0x40/0x50
cleanup_mnt+0x135/0x190
__cleanup_mnt+0x12/0x20
task_work_run+0x64/0xb0
__prepare_exit_to_usermode+0x1bc/0x1c0
__syscall_return_slowpath+0x47/0x230
do_syscall_64+0x64/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace caf08beafeca2392 ]---
BTRFS error (device dm-3): qgroup reserved space leaked
[CAUSE]
In the offending case, the offending operations are:
2/6: writev f2X[269 1 0 0 0 0] [1006997,67,288] 0
2/7: truncate f2X[269 1 0 0 48 1026293] 18388 0
The following sequence of events could happen after the writev():
CPU1 (writeback) | CPU2 (truncate)
-----------------------------------------------------------------
btrfs_writepages() |
|- extent_write_cache_pages() |
|- Got page for 1003520 |
| 1003520 is Dirty, no writeback |
| So (!clear_page_dirty_for_io()) |
| gets called for it |
|- Now page 1003520 is Clean. |
| | btrfs_setattr()
| | |- btrfs_setsize()
| | |- truncate_setsize()
| | New i_size is 18388
|- __extent_writepage() |
| |- page_offset() > i_size |
|- btrfs_invalidatepage() |
|- Page is clean, so no qgroup |
callback executed
This means, the qgroup reserved data space is not properly released in
btrfs_invalidatepage() as the page is Clean.
[FIX]
Instead of checking the dirty bit of a page, call
btrfs_qgroup_free_data() unconditionally in btrfs_invalidatepage().
As qgroup rsv are completely bound to the QGROUP_RESERVED bit of
io_tree, not bound to page status, thus we won't cause double freeing
anyway.
Fixes: 0b34c261e2 ("btrfs: qgroup: Prevent qgroup->reserved from going subzero")
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
NULL dereference occurs when string that is not ended with space or
newline is written to some dpm sysfs interface (for example pp_dpm_sclk).
This happens because strsep replaces the tmp with NULL if the delimiter
is not present in string, which is then dereferenced by tmp[0].
Reproduction example:
sudo sh -c 'echo -n 1 > /sys/class/drm/card0/device/pp_dpm_sclk'
Signed-off-by: Paweł Gronowski <me@woland.xyz>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Avoid kernel crash when vddci_control is SMU7_VOLTAGE_CONTROL_NONE and
vddci_voltage_table is empty. It has been tested on Intel Hades Canyon
(i7-8809G).
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=208489
Fixes: ac7822b002 ("drm/amd/powerplay: add smumgr support for VEGAM (v2)")
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Qiu Wenbo <qiuwenbo@phytium.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Commit 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064e ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com
Fixes: 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250 port")
Reported-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: stable <stable@vger.kernel.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct tty_port is part of the uart state and will never be NULL in
the receive helpers. Drop the bogus NULL checks and rename the
pointer-variables "port" to differentiate them from struct tty_struct
pointers (which can be NULL).
Fixes: 962963e4ee ("serial: tegra: Switch to using struct tty_port")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200710135947.2737-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 33ae787b74 ("serial: tegra: add support to ignore read") added
support for dropping input in case CREAD isn't set, but for PIO the
ignore_status_mask wasn't checked until after the character had been
put in the receive buffer.
Note that the NULL tty-port test is bogus and will be removed by a
follow-on patch.
Fixes: 33ae787b74 ("serial: tegra: add support to ignore read")
Cc: stable <stable@vger.kernel.org> # 5.4
Cc: Shardar Shariff Md <smohammed@nvidia.com>
Cc: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200710135947.2737-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prefetch work in mlx5_ib_prefetch_mr_work can be queued and able to run
concurrently with destruction of the implicit MR. The num_deferred_work
was intended to serialize this, but there is a race:
CPU0 CPU1
mlx5_ib_free_implicit_mr()
xa_erase(odp_mkeys)
synchronize_srcu()
__xa_erase(implicit_children)
mlx5_ib_prefetch_mr_work()
pagefault_mr()
pagefault_implicit_mr()
implicit_get_child_mr()
xa_cmpxchg()
atomic_dec_and_test(num_deferred_mr)
wait_event(imr->q_deferred_work)
ib_umem_odp_release(odp_imr)
kfree(odp_imr)
At this point in mlx5_ib_free_implicit_mr() the implicit_children list is
supposed to be empty forever so that destroy_unused_implicit_child_mr()
and related are not and will not be running.
Since it is not empty the destroy_unused_implicit_child_mr() flow ends up
touching deallocated memory as mlx5_ib_free_implicit_mr() already tore down the
imr parent.
The solution is to flush out the prefetch wq by driving num_deferred_work
to zero after creation of new prefetch work is blocked.
Fixes: 5256edcb98 ("RDMA/mlx5: Rework implicit ODP destroy")
Link: https://lore.kernel.org/r/20200719065435.130722-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The problems started with the revert (18cc7ac8a2). The
cdns_uart_console.index is statically assigned -1. When the port is
registered, Linux assigns consecutive numbers to it. It turned out that
when using ttyPS1 as console, the index is not updated as we are reusing
the same cdns_uart_console instance for multiple ports. When registering
ttyPS0, it gets updated from -1 to 0, but when registering ttyPS1, it
already is 0 and not updated.
That led to 2ae11c46d5. It assigns the index prior to registering
the uart_driver once. Unfortunately, that ended up breaking the
situation where the probe order does not match the id order. When using
the same device tree for both uboot and linux, it is important that the
serial0 alias points to the console. So some boards reverse those
aliases. This was reported by Jan Kiszka. The proposed fix was reverting
the index assignment and going back to the previous iteration.
However such a reversed assignement (serial0 -> uart1, serial1 -> uart0)
was already partially broken by the revert (18cc7ac8a2). While the
ttyPS device works, the kmsg connection is already broken and kernel
messages go missing. Reverting the id assignment does not fix this.
>From the xilinx_uartps driver pov (after reverting the refactoring
commits), there can be only one console. This manifests in static
variables console_pprt and cdns_uart_console. These variables are not
properly linked and can go out of sync. The cdns_uart_console.index is
important for uart_add_one_port. We call that function for each port -
one of which hopefully is the console. If it isn't, the CON_ENABLED flag
is not set and console_port is cleared. The next cdns_uart_probe call
then tries to register the next port using that same cdns_uart_console.
It is important that console_port and cdns_uart_console (and its index
in particular) stay in sync. The index assignment implemented by
Shubhrajyoti Datta is correct in principle. It just may have to happen a
second time if the first cdns_uart_probe call didn't encounter the
console device. And we shouldn't change the index once the console uart
is registered.
Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Link: https://lore.kernel.org/linux-serial/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com/
Fixes: 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console and driver structures"")
Fixes: 2ae11c46d5 ("tty: xilinx_uartps: Fix missing id assignment to the console")
Fixes: 76ed2e1057 ("Revert "tty: xilinx_uartps: Fix missing id assignment to the console"")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200713073227.GA3805@laureti-dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting general protection fault in do_con_write() [1] caused
by vc->vc_screenbuf == ZERO_SIZE_PTR caused by vc->vc_screenbuf_size == 0
caused by vc->vc_cols == vc->vc_rows == vc->vc_size_row == 0 caused by
fb_set_var() from ioctl(FBIOPUT_VSCREENINFO) on /dev/fb0 , for
gotoxy(vc, 0, 0) from reset_terminal() from vc_init() from vc_allocate()
from con_install() from tty_init_dev() from tty_open() on such console
causes vc->vc_pos == 0x10000000e due to
((unsigned long) ZERO_SIZE_PTR) + -1U * 0 + (-1U << 1).
I don't think that a console with 0 column or 0 row makes sense. And it
seems that vc_do_resize() does not intend to allow resizing a console to
0 column or 0 row due to
new_cols = (cols ? cols : vc->vc_cols);
new_rows = (lines ? lines : vc->vc_rows);
exception.
Theoretically, cols and rows can be any range as long as
0 < cols * rows * 2 <= KMALLOC_MAX_SIZE is satisfied (e.g.
cols == 1048576 && rows == 2 is possible) because of
vc->vc_size_row = vc->vc_cols << 1;
vc->vc_screenbuf_size = vc->vc_rows * vc->vc_size_row;
in visual_init() and kzalloc(vc->vc_screenbuf_size) in vc_allocate().
Since we can detect cols == 0 or rows == 0 via screenbuf_size = 0 in
visual_init(), we can reject kzalloc(0). Then, vc_allocate() will return
an error, and con_write() will not be called on a console with 0 column
or 0 row.
We need to make sure that integer overflow in visual_init() won't happen.
Since vc_do_resize() restricts cols <= 32767 and rows <= 32767, applying
1 <= cols <= 32767 and 1 <= rows <= 32767 restrictions to vc_allocate()
will be practically fine.
This patch does not touch con_init(), for returning -EINVAL there
does not help when we are not returning -ENOMEM.
[1] https://syzkaller.appspot.com/bug?extid=017265e8553724e514e8
Reported-and-tested-by: syzbot <syzbot+017265e8553724e514e8@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200712111013.11881-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit
84e6ffb2c4 ("arm: add support for folded p4d page tables")
updated create_mapping_late() to take folded P4Ds into account when
creating mappings, but inverted the p4d_alloc() failure test, resulting
in no mapping to be created at all.
When the EFI rtc driver subsequently tries to invoke the EFI GetTime()
service, the memory regions covering the EFI data structures are missing
from the page tables, resulting in a crash like
Unable to handle kernel paging request at virtual address 5ae0cf28
pgd = (ptrval)
[5ae0cf28] *pgd=80000040205003, *pmd=00000000
Internal error: Oops: 207 [#1] SMP THUMB2
Modules linked in:
CPU: 0 PID: 7 Comm: kworker/u32:0 Not tainted 5.7.0+ #92
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
Workqueue: efi_rts_wq efi_call_rts
PC is at efi_call_rts+0x94/0x294
LR is at efi_call_rts+0x83/0x294
pc : [<c0b4f098>] lr : [<c0b4f087>] psr: 30000033
sp : e6219ef0 ip : 00000000 fp : ffffe000
r10: 00000000 r9 : 00000000 r8 : 30000013
r7 : e6201dd0 r6 : e6201ddc r5 : 00000000 r4 : c181f264
r3 : 5ae0cf10 r2 : 00000001 r1 : e6201dd0 r0 : e6201ddc
Flags: nzCV IRQs on FIQs on Mode SVC_32 ISA Thumb Segment none
Control: 70c5383d Table: 661cc840 DAC: 00000001
Process kworker/u32:0 (pid: 7, stack limit = 0x(ptrval))
...
[<c0b4f098>] (efi_call_rts) from [<c0448219>] (process_one_work+0x16d/0x3d8)
[<c0448219>] (process_one_work) from [<c0448581>] (worker_thread+0xfd/0x408)
[<c0448581>] (worker_thread) from [<c044ca7b>] (kthread+0x103/0x104)
...
Fixes: 84e6ffb2c4 ("arm: add support for folded p4d page tables")
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
__vdso_*() should be removed and fallback used if CNTCVT is not
available by cntvct_functional(). __vdso_clock_gettime64 when added
previous commit is using the incorrect CNTCVT value in that state.
__vdso_clock_gettime64 is also added to remove it's symbol.
Cc: stable@vger.kernel.org
Fixes: 74d06efb9c ("ARM: 8932/1: Add clock_gettime64 entry point")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Robin Murphy <robin.mruphy@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Unprivileged memory accesses generated by the so-called "translated"
instructions (e.g. LDRT) in kernel mode can cause user watchpoints to fire
unexpectedly. In such cases, the hw_breakpoint logic will invoke the user
overflow handler which will typically raise a SIGTRAP back to the current
task. This is futile when returning back to the kernel because (a) the
signal won't have been delivered and (b) userspace can't handle the thing
anyway.
Avoid invoking the user overflow handler for watchpoints triggered by
kernel uaccess routines, and instead single-step over the faulting
instruction as we would if no overflow handler had been installed.
Cc: <stable@vger.kernel.org>
Fixes: f81ef4a920 ("ARM: 6356/1: hw-breakpoint: add ARM backend for the hw-breakpoint framework")
Reported-by: Luis Machado <luis.machado@linaro.org>
Tested-by: Luis Machado <luis.machado@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8W9DAACgkQqDIjiipP
6E9HUwf+Of/ePXWAO59IGMsiRdh+yYawc7blshVxtuw9vgfFfXSUXWyoAO8WH6zS
VOzmlDoze+jdG4VKAr0elFOkXAHjdgfwsVoLAU1aJz1r/rcpt3j8oc8JPKTxck7I
Yq5L9+I/36sULZt7Pa8VaendoswbrKDbHtQFqQaT+h2LtCdK2kEeRp44Xr3fqIPc
fuHAzetjWJ20Iy7YRkI3jzL9DAcoXZWdctSoC8FYEWtP7RaGVZVnxBPyaoiGFVJc
WnZApwxW6Ju03Uav6ypy7fP5A3utFi119pRuyadQYCJT1n9NlzZMmCA+fCCx09+Y
fvuXIayg6bj7++YD1zLPPFn4rgTY/g==
=vRtM
-----END PGP SIGNATURE-----
Merge tag 'timers-v5.8-rc7' of https://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull a timer chip fix from Daniel Lezcano:
- Fix kernel panic at suspend / resume time on TI am3/am4 (Tony Lindgren)
