max_req_size is calculated by 'max_blk_size * max_blk_count' in the TMIO
core. So, specifying U32_MAX as max_blk_count will overflow this
calculation. It will cause no harm in practice because the immense high
number will overflow into another immense high number. However, it is
not good coding practice, so calculate max_blk_count so that
max_req_size will fit into unsigned int on ARM32/64.
Thanks to the Renesas BSP team for the bug report!
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will need it later for other calculations.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mostly year updates, but one addition as well.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the i.MX23/28 reference manuals both mmc interfaces support
the MMC_ERASE command. So enable this capability in the driver to allow
erase/discard/trim requests.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case spi_sync_locked fails, the fix reports the error and
returns the error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some controllers, in Present State Register, Data Line
Active bit is not reliable for commands (such as CMD6, CMD7,
CMD12, CMD28, CMD29, or CMD38) with busy signal. DLA affects
Command with Data Inhibit bit. Therefore, software driver
may not know the busy status in DLA/CDIHB.
Futunately MMC core driver has already polled card status
with CMD13 after sending any command with busy signal. So
we can just ignore CDIHB never released issue for such
controllers. This patch is to add a quirk to handle this.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Invalid Transfer Complete (IRQSTAT[TC]) bit could be set during
multi-write operation even when the BLK_CNT in BLKATTR register
has not reached zero. Therefore, Transfer Complete might be
reported twice due to this erratum since a valid Transfer Complete
occurs when BLK_CNT reaches zero. This erratum is to fix this issue
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the event of that any data error (like, IRQSTAT[DCE]) occurs
during an eSDHC data transaction where DMA is used for data
transfer to/from the system memory, setting the SYSCTL[RSTD]
register may cause a system hang. If software sets the register
SYSCTL[RSTD] to 1 for error recovery while DMA transferring is
not complete, eSDHC may hang the system bus. This happens because
the software register SYSCTL[RSTD] resets the DMA engine without
waiting for the completion of pending system transactions. This
erratum is to fix this issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not
reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock),
and 0xC(2^25 SD clock). The data timeout counter can count from
2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout
counter counts for only 2^13 SD clocks.
A-008358: The data timeout counter value loaded into the timeout
counter is less than expected and can result into early timeout
error in case of eSDHC data transactions. The table below shows
the expected vs actual timeout period for different values of
SYSCTL[DTOCV]:
these two erratum has the same quirk to control it, and set
SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Software writing to the Transfer Type configuration register
(system clock domain) can cause a setup/hold violation in the
CRC flops (card clock domain), which can cause write accesses
to be sent with corrupt CRC values. This issue occurs only for
write preceded by read. this erratum is to fix this issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to add erratum A011334 support in lx2160 2.0 SoC
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As mmci_variant_init() is a local function to mmci.c, let's convert it into
static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It's good practice to share functions via header files, rather than from
the c-files. Therefore, let's move sdmmc_variant_init() to mmci.h.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It seems a bit silly to have a header file to share only the
qcom_variant_init() function. So, let's just drop it and move the
declaration of the function into the common mmci.h instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Having mmci_dmae_start() to invoke the shared function, dml_start_xfer(),
explicitly for the qcom variant isn't very nice. Let's clean up this code
by moving the qcom specific parts into the qcom ->dma_start() callback and
then drop dml_start_xfer() altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
There's no point clearing the variant flag in case the qcom variant fails
to setup DMA. This is because if mmci_dma_setup() fails, then the use_dma
flag remains set to false, which leads to mmci using PIO mode and not DMA.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Some of the DMA functions are shared via mmci.h, however they are not
implemented unless CONFIG_DMA_ENGINE is set. Therefore, add that constraint
to the header file as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
commit 5b0d62108b ("mmc: sdhci-omap: Add platform specific reset
callback") skips data resets during tuning operation. Because of this,
a data error or data finish interrupt might still arrive after a command
error has been handled and the mrq ended. This ends up with a "mmc0: Got
data interrupt 0x00000002 even though no data operation was in progress"
error message.
Fix this by adding a platform specific callback for sdhci_irq. Mark the
mrq as a failure but wait for a data interrupt instead of calling
finish_mrq().
Fixes: 5b0d62108b ("mmc: sdhci-omap: Add platform specific reset
callback")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The alcor driver is setting up data transfer and submitting the associated
MMC command at the same time. While this works most of the time, it
occasionally causes problems upon write.
In the working case, after setting up the data transfer and submitting
the MMC command, an interrupt comes in a moment later with CMD_END and
WRITE_BUF_RDY bits set. The data transfer then happens without problem.
However, on occasion, the interrupt that arrives at that point only
has WRITE_BUF_RDY set. The hardware notifies that it's ready to write
data, but the associated MMC command is still running. Regardless, the
driver was proceeding to write data immediately, and that would then cause
another interrupt indicating data CRC error, and the write would fail.
Additionally, the transfer setup function alcor_trigger_data_transfer()
was being called 3 times for each write operation, which was confusing
and may be contributing to this issue.
Solve this by tweaking the driver behaviour to follow the sequence observed
in the original ampe_stor vendor driver:
1. When starting request handling, write 0 to DATA_XFER_CTRL
2. Submit the command
3. Wait for CMD_END interrupt and then trigger data transfer
4. For the PIO case, trigger the next step of the data transfer only
upon the following DATA_END interrupt, which occurs after the block has
been written.
I confirmed that the read path still works (DMA & PIO) and also now
presents more consistency with the operations performed by ampe_stor.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Fixes: c5413ad815 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R-Car Gen2 has two different SDHI incarnations in the same chip. The
older one does not support the recently introduced 32 bit register
access to the block count register. Make sure we use this feature only
after the first known version.
Thanks to the Renesas Testing team for this bug report!
Fixes: 5603731a15 ("mmc: tmio: fix access width of Block Count Register")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Phong Hoang <phong.hoang.wz@renesas.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting max_blk_count to 1 here was causing the mmc block layer
to always use the MMC_READ_SINGLE_BLOCK command here, which the
driver does not DMA-accelerate.
Drop the max_blk_ settings here. The mmc host defaults suffice,
along with the max_segs and max_seg_size settings, which I have
now documented in more detail.
Now each MMC command reads 4 512-byte blocks, using DMA instead of
PIO. On my SD card, this increases read performance (measured with dd)
from 167kb/sec to 4.6mb/sec.
Link: http://lkml.kernel.org/r/CAD8Lp47L5T3jnAjBiPs1cQ+yFA3L6LJtgFvMETnBrY63-Zdi2g@mail.gmail.com
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Fixes: c5413ad815 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 6d5cd068ee ("mmc: sdhci: use WP GPIO in
sdhci_check_ro()") and commit 39ee32ce48 ("mmc: sdhci-omap: drop
->get_ro() implementation"), sdhci-omap relied on SDHCI_PRESENT_STATE
to check if the card is read-only, if wp-gpios is not populated
in device tree. However SDHCI_PRESENT_STATE in sdhci-omap does not have
correct read-only state.
sdhci-omap can be used by platforms with both micro SD slot and standard
SD slot with physical write protect pin (using GPIO). Set caps2 to
MMC_CAP2_NO_WRITE_PROTECT based on if wp-gpios property is populated or
not.
This fix is required since existing device-tree node doesn't have
"disable-wp" property and to preserve old-dt compatibility.
Fixes: 6d5cd068ee ("mmc: sdhci: use WP GPIO in sdhci_check_ro()")
Fixes: 39ee32ce48 ("mmc: sdhci-omap: drop ->get_ro() implementation")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Building with clang finds a mistaken __init tag:
WARNING: vmlinux.o(.text+0x5e4250): Section mismatch in reference from the function davinci_mmcsd_probe() to the function .init.text:init_mmcsd_host()
The function davinci_mmcsd_probe() references
the function __init init_mmcsd_host().
This is often because davinci_mmcsd_probe lacks a __init
annotation or the annotation of init_mmcsd_host is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clang points out several instances of mismatched types in this drivers,
all coming from a single declaration:
drivers/mmc/host/pxamci.c:193:15: error: implicit conversion from enumeration type 'enum dma_transfer_direction' to
different enumeration type 'enum dma_data_direction' [-Werror,-Wenum-conversion]
direction = DMA_DEV_TO_MEM;
~ ^~~~~~~~~~~~~~
drivers/mmc/host/pxamci.c:212:62: error: implicit conversion from enumeration type 'enum dma_data_direction' to
different enumeration type 'enum dma_transfer_direction' [-Werror,-Wenum-conversion]
tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction,
The behavior is correct, so this must be a simply typo from
dma_data_direction and dma_transfer_direction being similarly named
types with a similar purpose.
Fixes: 6464b71409 ("mmc: pxamci: switch over to dmaengine use")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=VBaU
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
The original purpose of the code I fix is to replace max_discard with
max_trim if max_trim is less than max_discard. When max_discard is 0
we should replace max_discard with max_trim as well, because
max_discard equals 0 happens only when the max_do_calc_max_discard
process is overflowed, so if mmc_can_trim(card) is true, max_discard
should be replaced by an available max_trim.
However, in the original code, there are two lines of code interfere
the right process.
1) if (max_discard && mmc_can_trim(card))
when max_discard is 0, it skips the process checking if max_discard
needs to be replaced with max_trim.
2) if (max_trim < max_discard)
the condition is false when max_discard is 0. it also skips the process
that replaces max_discard with max_trim, in fact, we should replace the
0-valued max_discard with max_trim.
Signed-off-by: Jiong Wu <Lohengrin1024@gmail.com>
Fixes: b305882fbc (mmc: core: optimize mmc_calc_max_discard)
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the card was removed in suspended state and a new one was inserted,
print a debug log when the check detects that it's not the old card.
Signed-off-by: hongjiefang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD spec v5.1 adds discard support. The flows and commands are similar to
mmc, so just set the discard arg in CMD38.
A host which supports DISCARD shall check if the DISCARD_SUPPORT (b313)
is set in the SD_STATUS register. If the card does not support discard,
the host shall not issue DISCARD command, but ERASE command instead.
Post the DISCARD operation, the card may de-allocate the discarded
blocks partially or completely. So the host mustn't make any assumptions
concerning the content of the discarded region. This is unlike ERASE
command, in which the region is guaranteed to contain either '0's or
'1's, depends on the content of DATA_STAT_AFTER_ERASE (b55) in the scr
register.
One more important difference compared to ERASE is the busy timeout
which we will address on the next patch.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the response type of CMD6 is R1B, when the first CMD6 gets response
CRC error, do retry may get timeout error due to card may still in
busy state, which cause this retry make no sense.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Logical block size is the lowest possible block size that the storage
device can address. Max segment size is often related with controller's
DMA capability. And it is reasonable to align max segment size with
logical block size.
SDHCI sets un-aligned max segment size, and causes ADMA error, so
fix it by aligning max segment size with logical block size.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: linux-block@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Free up the allocated memory in the case of error return
The value of mmc_host->cqe_enabled stays 'false'. Thus, cqhci_disable
(mmc_cqe_ops->cqe_disable) won't be called to free the memory. Also,
cqhci_disable() seems to be designed to disable and free all resources, not
suitable to handle this corner case.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is not enough space being allocated when DCMD is disabled.
CQE_DCMD is not necessary to be enabled when CQE is enabled.
(Software could halt CQE to send command)
In the case that CQE_DCMD is not enabled, it still needs to allocate
space for data transfer. For instance:
CQE_DCMD is enabled: 31 slots space (one slot used by DCMD)
CQE_DCMD is disabled: 32 slots space
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD).
In such case mmc_should_fail_request is directly dereferencing
mrq->cmd while cmd is NULL.
Fix this by checking for mrq->cmd pointer.
Fixes: 72a5af554d ("mmc: core: Add support for handling CQE requests")
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In R-Car Gen2 or later, the maximum number of transfer blocks are
changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register
should use iowrite32().
If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this
value will not be cleared. So, SD/MMC card initialization fails.
So, check for the bigger register and use apropriate write. Also, mark
the register as extended on Gen2.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: use max_blk_count in if(), add Gen2, update commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@kernel.org
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[Ulf: Fixed build error]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the DMAC interrupts enabled while the Linux driver didn't use those.
The SDHI driver's interrupt handler somehow assumes that, even if an
SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think
that if none of the enabled interrupts happened and got handled, we
should return IRQ_NONE -- that way the kernel IRQ code recoginizes
a spurious interrupt and masks it off pretty quickly...
Fixes: 7729c7a232 ("mmc: tmio: Provide separate interrupt handlers")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only user of mmc_align_data_size() is sdio_align_size(), which is
called from SDIO func drivers to let them distinguish, how to optimally
allocate data buffers.
Let's move mmc_align_data_size() close to the SDIO code as to make it
static, rename it to _sdio_align_size() and simplify its definition, all
with the purpose of clarifying that this is SDIO specific.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
When using the mmc_spi driver with a card-detect pin, I noticed that the
card was not detected immediately after probe, but only after it was
unplugged and plugged back in (and the CD IRQ fired).
The call tree looks something like this:
mmc_spi_probe
mmc_add_host
mmc_start_host
_mmc_detect_change
mmc_schedule_delayed_work(&host->detect, 0)
mmc_rescan
host->bus_ops->detect(host)
mmc_detect
_mmc_detect_card_removed
host->ops->get_cd(host)
mmc_gpio_get_cd -> -ENOSYS (ctx->cd_gpio not set)
mmc_gpiod_request_cd
ctx->cd_gpio = desc
To fix this issue, call mmc_detect_change after the card-detect GPIO/IRQ
is registered.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC OF parsing functions, which parses various host DT properties, should
stay close to each other. Therefore, let's move mmc_of_parse_voltage()
close to mmc_of_parse() into host.c.
Additionally, there is no reason to build the code only when CONFIG_OF is
set, as there should be stub functions for the OF helpers that is being
used, so let's drop this condition as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only left user of mmc_regulator_get_ocrmask() is the mmc core itself.
Therefore, let's drop the export and turn it into static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc regulator helper functions, are placed in the extensive core.c
file. In a step towards trying to create a better structure of files,
avoiding too many lines of code per file, let's move these helpers to a new
file, regulator.c.
Moreover, this within this context it makes sense to also drop the export
of mmc_vddrange_to_ocrmask(), but instead let's make it internal to the mmc
core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's drop the open-coding of the parsing of the "voltage-ranges" DT
property and convert to use the common mmc_of_parse_voltage() API instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All callers of mmc_wait_for_app_cmd() set the retries in-parameter to
MMC_CMD_RETRIES. This is silly, so let's just drop the in-parameter
altogether, as to simplify the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_wait_for_app_cmd() is an internal function for sd_ops.c, thus let's
drop the unnecessary export and turn it into static function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SCC is used for SDR104/HS200/HS400. We need to change SCC_DT2FF
according to the mode. If it is inappropriate, CRC error tends to occur.
This adds variable "tap_hs400" for HS400 mode and configures SCC_DT2FF
as needed.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebased to upstream and updated commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current approach with sending a CMD12 (STOP_TRANSMISSION) to complete a
data transfer request, either because of using the open-ended transmission
type or because of receiving an error during a pre-defined data transfer,
isn't sufficient for the STM32 sdmmc variant. More precisely, this variant
needs to clear the DPSM ("Data Path State Machine") by sending a CMD12, for
all failing ADTC commands.
Support this, by adding a struct mmc_command inside the struct mmci_host
and initialize it to a CMD12 during ->probe(). Let's also add checks for
the new conditions, to enable mmci_data_irq() and mmci_cmd_irq() to
postpone the calls to mmci_request_end(), but instead send the CMD12.
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
according to what the compiler looks for, where we are expecting to fall
through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI core is know properly checking for the state of a WP GPIO,
so there is no longer any need for the sdhci-tegra code to implement
->get_ro() using mmc_gpio_get_ro().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI core is now properly checking for the state of a WP GPIO,
so there is no longer any need for the sdhci-omap code to implement
->get_ro() using mmc_gpio_get_ro().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even though SDHCI controllers may have a dedicated WP pin that can be
queried using the SDHCI_PRESENT_STATE register, some platforms may
chose to use a separate regular GPIO to route the WP signal. Such a
GPIO is typically represented using the wp-gpios property in the
Device Tree.
Unfortunately, the current sdhci_check_ro() function does not make use
of such GPIO when available: it either uses a host controller specific
->get_ro() operation, or uses the SDHCI_PRESENT_STATE. Several host
controller specific ->get_ro() functions are implemented just to check
a WP GPIO state.
Instead of pushing this to more controller-specific implementations,
let's handle this in the core SDHCI code, just like it is already done
for the CD GPIO in sdhci_get_cd().
The below patch simply changes sdhci_check_ro() to use the value of
the WP GPIO if available.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The WMT SDMMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> so drop this surplus include.
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Sunxi MMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: cenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI PXAv2 driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> so drop this surplus include.
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI BCM Kona driver uses slot GPIO helpers and does not
make any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MXS-MMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MXCMMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Jun Qian <hangdianqj@163.com>
Cc: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is an if block that is not indented, fix this. Also add a
break statement on the default case to clean up a cppcheck warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD specs version 4.x and 5.x have a dedicated slices in the SCR register.
Higher versions will rely on a combination of the existing fields.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In MMC, the discard arg is a read-only ext_csd parameter - set it once
on card init. To be consistent, do that for SD as well even though its
discard arg is always 0x0.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The argument "override_active_level" made it possible to
enforce a specific polarity on the write-protect
GPIO line. All callers in the kernel pass "false" to this
call after I have converted all drivers to use GPIO machine
descriptors, so remove the argument and clean out this.
This kind of polarity inversion should be handled by the
GPIO descriptor inside the GPIO library if needed.
This rids us of one instance of the kludgy calls into
the gpiod_get_raw_value() API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver(). Drop the duplicate assignment.
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The BCM2835 MMC host driver uses a pointer to get from the private
bcm2835_host structure to the generic mmc_host structure. However the
latter is always immediately preceding the former in memory, so compute
its address with a subtraction (which is cheaper than a dereference) and
drop the superfluous pointer.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Alexander Graf <agraf@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
bcm2835_add_host() invokes IS_ERR_OR_NULL() on a DMA channel pointer,
however dma_request_slave_channel() (which was used to populate the
pointer) never returns an error pointer. So a NULL pointer check is
sufficient.
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When running OMAP1 kernel on QEMU, MMC access is annoyingly noisy:
MMC: CTO of 0xff and 0xfe cannot be used!
MMC: CTO of 0xff and 0xfe cannot be used!
MMC: CTO of 0xff and 0xfe cannot be used!
[ad inf.]
Emulator warnings appear to be valid. The TI document SPRU680 [1]
("OMAP5910 Dual-Core Processor MultiMedia Card/Secure Data Memory Card
(MMC/SD) Reference Guide") page 36 states that the maximum timeout is 253
cycles and "0xff and 0xfe cannot be used".
Fix by using 0xfd as the maximum timeout.
Tested using QEMU 2.5 (Siemens SX1 machine, OMAP310), and also checked on
real hardware using Palm TE (OMAP310), Nokia 770 (OMAP1710) and Nokia N810
(OMAP2420) that MMC works as before.
[1] http://www.ti.com/lit/ug/spru680/spru680.pdf
Fixes: 730c9b7e66 ("[MMC] Add OMAP MMC host driver")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Below are the supported DMA types in Host Control1 Register
with Version 4 enable
b'00 - SDMA
b'01 - Not Used
b'10 - ADMA2
b'11 - ADMA2 or ADMA3
ADMA3 uses Command Descriptor to issue an SD command.
A multi-block data transfer is performed by using a pair of CMD
descriptor and ADMA2 descriptor.
ADMA3 performs multiple of multi-block data transfer by using
Integrated Descriptor which is more suitable for Command Queuing
to fetch both Command and Transfer descriptors.
Host Capabilities register indicates the supports of ADMA3 DMA.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds support for 8-bit buswidth.
Relevant SDCR value modified.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This fixes card initialization failure in high speed mode.
If U-Boot uses SDR or HS200/400 mode before starting Linux and Linux
DT does not enable SDR/HS200/HS400 mode, card initialization fails in
high speed mode.
It is necessary to initialize SCC registers during card initialization
phase. HW reset function is registered only for a port with either of
SDR/HS200/HS400 properties in device tree. If SDR/HS200/HS400 properties
are not present in device tree, SCC registers will not be reset. In SoC
that support SCC registers, HW reset function should be registered
regardless of the configuration of device tree.
Reproduction procedure:
- Use U-Boot that support MMC HS200/400 mode.
- Delete HS200/HS400 properties in device tree.
(Delete mmc-hs200-1_8v and mmc-hs400-1_8v)
- MMC port works high speed mode and all commands fail.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drop the custom code to get the 'cd' and 'wp' GPIOs. The driver now
calls mmc_of_parse() which will init these from devicetree or
device properties.
Also drop the custom code to get the 'power' GPIO. The MMC core
provides us with the means to power the MMC card through an external
regulator.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
O2 SD host controller only need set the quirk2 flag
SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD when
work on force 1.8v emmc mode but not normal mode
Signed-off-by: Ernest Zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mmc/host/jz4740_mmc.c:745:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mmc/host/jz4740_mmc.c:779:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of error, the function devm_kzalloc() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: fadac7488064 ("mmc: sdhci-esdhc-imx: add CMDQ support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a plan to build the kernel with -Wimplicit-fallthrough and
this place in the code produced a warning (W=1).
In this particular case rewrote the comment to start with the string "fall
through", so as to match the regular expression expected by GCC. Truncate
the comment slightly to fit the max line length of 80 characters.
This commit remove the following warning:
drivers/mmc/core/host.c:196:14: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Program initial drive code offsets which will be used by auto
calibration process.
Program fixed drive strengths for SDMMC pads in pad control
register when auto cal timeouts.
Fixed settings are based on Pre-SI analysis of the pad design.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, USDHC do not generate transfer complete interrupt
when send a non-data-command with R1b response. But if want
to support DCMD in CMDQ, need to change this, the DCMD IC
logic require the USDHC to enable this function, otherwise
DCMD will never get a CC(command complete) interrupt.
This patch set ESDHC_VEND_SPEC2_EN_BUSY_IRQ and add DCMD support.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add CMDQ support for imx8qm/imx8qxp.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Rebased on top of latest changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change to use sdhci_set_timeout() to set the maximum timeout, so that
the host can use it's own set_timeout() callback to set the maximum
timeout if the host has.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an new esdhc_soc_data for i.MX8QXP, and add HS400_ES mode
support.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Rebased on top of latest changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some eMMC, after switch to HS400ES mode, it need to config the strobe
dll target dealy even if the clock is 50MHZ or 25MHz, otherwise will meet
CMD index/crc error when send CMD13 to check the switch status.
[ 2.473915] IRQ status 0x000a8001
[ 2.473934] mmc2: mmc_select_hs400es failed, error -84
[ 2.473938] mmc2: error -84 whilst initialising MMC card
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When removing the driver make sure to undo the PM autosuspend configured
when probing the host.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In sdio_bus_remove the variable is unneeded,remove it now.
Signed-off-by: wangbo <wang.bo116@zte.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1. O2 Host Controller PLL lock status is not in compliance with
CLOCK_CONTROL register bit 1
2. O2 Host Controller card detect function only work when PLL is
enabled and locked
Signed-off-by: Ernest Zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to handle mmc_of_parse() errors during probe otherwise the
MMC driver could start without proper initialization (e.g. power sequence).
Fixes: 476bf3d62d ("mmc: sdhci-brcmstb: Add driver for Broadcom BRCMSTB SoCs")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When host set the host->tuning_delay, even the last tuning
command need a delay, otherwise the first command after the
tuning will meet issue.
Take i.MX7D as an example, there will be the following log:
mmc2: switch to high-speed from hs200 failed, err:-110
mmc2: error -110 whilst initialising MMC card
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's observed that i.MX uSDHC needed delay between tuning
cycles for HS200 successful tuning. This patch is to set 1ms
delay for that.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
i.MX6ULL has errata ERR010450, point out that due to SOC I/O
timing limitation, for eMMC HS200 and SD/SDIO 3.0 SDR104, the
clock rate can't exceed 150MHz. And for eMMC DDR52 and SD/SDIO
DDR50 mode, the clock rate can't exceed 45MHz.
This patch add this limit for imx6ull.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed comments and whitespace]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now tuning reset will be done when the timing is MMC_TIMING_LEGACY/
MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS. But for timing MMC_TIMING_MMC_HS,
we can not do tuning reset, otherwise HS400 timing is not right.
Here is the process of init HS400, first finish tuning in HS200 mode,
then switch to HS mode and 8 bit DDR mode, finally switch to HS400
mode. If we do tuning reset in HS mode, this will cause HS400 mode
lost the tuning setting, which will cause CRC error.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v4.12+
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: d9370424c9 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DDR50 tuning is optinally defined in sd 3.0 spec. And i.MX
uSDHC internally already uses a fixed optimized timing for
DDR50, normally does not require tuning for DDR50 mode.
This patch specify a new execute_tuning function for i.MX
uSDHC, do not impact i.MX eSDHC.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit ESDHC_STD_TUNING_EN may be configed by bootloader code if it
choose to use standard tuning method. So on linux side, if choose to
use manual tuning method, need to clear the bit ESDHC_STD_TUNING_EN,
remove the impact of bootloader code.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variant specific driver data doesn't change at run-time, so mark it as
const to reflect that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes the following sparse warning:
drivers/mmc/host/sdhci_am654.c:161:18: warning:
symbol 'sdhci_am654_ops' was not declared. Should it be static?
Fixes: aff88ff23512 ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFRBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxgqNUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGwsoH+OVXu0NQofwTvVru
8lgF3BSDG2mhf7mxbBBlBizGVy9jnjRNGCFMC+Jq8IwiFLwprja/G27kaDTkpuF1
PHC3yfjKvjTeUP5aNdHlmxv6j1sSJfZl0y46DQal4UeTG/Giq8TFTi+Tbz7Wb/WV
yCx4Lr8okAwTuNhnL8ojUCVIpd3c8QsyR9v6nEQ14Mj+MvEbokyTkMJV0bzOrM38
JOB+/X1XY4JPZ6o3MoXrBca3bxbAJzMneq+9CWw1U5eiIG3msg4a+Ua3++RQMDNr
8BP0yCZ6wo32S8uu0PI6HrZaBnLYi5g9Wh7Q7yc0mn1Uh1zWFykA6TtqK90agJeR
A6Ktjw==
=scY4
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rc6' into for-5.1/block
Pull in 5.0-rc6 to avoid a dumb merge conflict with fs/iomap.c.
This is needed since io_uring is now based on the block branch,
to avoid a conflict between the multi-page bvecs and the bits
of io_uring that touch the core block parts.
* tag 'v5.0-rc6': (525 commits)
Linux 5.0-rc6
x86/mm: Make set_pmd_at() paravirt aware
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
MAINTAINERS: unify reference to xen-devel list
x86/mm/cpa: Fix set_mce_nospec()
futex: Handle early deadlock return correctly
futex: Fix barrier comment
net: dsa: b53: Fix for failure when irq is not defined in dt
blktrace: Show requests without sector
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
signal: Better detection of synchronous signals
...
QUEUE_FLAG_NO_SG_MERGE has been killed, so kill BLK_MQ_F_SG_MERGE too.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit bb36489032 ("mmc: meson-gx: Free irq in release() callback")
changed the _probe code to use request_threaded_irq() instead of
devm_request_threaded_irq().
Unfortunately this removes a fallback for the interrupt name:
devm_request_threaded_irq() uses the device name as fallback if the
given IRQ name is NULL. request_threaded_irq() has no such fallback,
thus /proc/interrupts shows "(null)" instead.
Explicitly pass the dev_name() so we get the IRQ name shown in
/proc/interrupts again.
While here, also fix the indentation of the request_threaded_irq()
parameter list.
Fixes: bb36489032 ("mmc: meson-gx: Free irq in release() callback")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The kblockd workqueue is created with the WQ_MEM_RECLAIM flag set.
This generates a rescuer thread for that queue that will trigger when
the CPU is under heavy load and collect the uncompleted work.
In the case of mmc, this creates the possibility of a deadlock when
there are multiple partitions on the device as other blk-mq work is
also run on the same queue. For example:
- worker 0 claims the mmc host to work on partition 1
- worker 1 attempts to claim the host for partition 2 but has to wait
for worker 0 to finish
- worker 0 schedules complete_work to release the host
- rescuer thread is triggered after time-out and collects the dangling
work
- rescuer thread attempts to complete the work in order starting with
claim host
- the task to release host is now blocked by a task to claim it and
will never be called
The above results in multiple hung tasks that lead to failures to
mount partitions.
Handling complete_work on a separate workqueue avoids this by keeping
the work completion tasks separate from the other blk-mq work. This
allows the host to be released without getting blocked by other tasks
attempting to claim the host.
Signed-off-by: Zachary Hays <zhays@lexmark.com>
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC device tree bindings include properties used to signal various
signalling speed modes. Until now the sunxi driver was accepting them
without any further filtering, while the sunxi device trees were not
actually using them.
Since some of the H5 boards can not run at higher speed modes stably,
we are resorting to declaring the higher speed modes per-board.
Regardless, having boards declare modes and blindly following them,
even without proper support in the driver, is generally a bad thing.
Filter out all unsupported modes from the capabilities mask after
the device tree properties have been parsed.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some H5 boards seem to not have proper trace lengths for eMMC to be able
to use the default setting for the delay chains under HS-DDR mode. These
include the Bananapi M2+ H5 and NanoPi NEO Core2. However the Libre
Computer ALL-H3-CC-H5 works just fine.
For the H5 (at least for now), default to not enabling HS-DDR modes in
the driver, and expect the device tree to signal HS-DDR capability on
boards that work.
Reported-by: Chris Blake <chrisrblake93@gmail.com>
Fixes: 07bafc1e35 ("mmc: sunxi: Use new timing mode for A64 eMMC controller")
Cc: <stable@vger.kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
to set cmd internal delay, need set PAD_TUNE register but not PAD_CMD_TUNE
register.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Fixes: 1ede5cb88a ("mmc: mediatek: Use data tune for CMD line tune")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path. The channel may
therefore be leaked, in particular if devm_clk_get() causes probe
deferral. Fix it.
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.12+
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SPDX license identifier and the boiler plate text are
contradicting. Only the SPDX license identifier is needed. The
other one is removed.
Fixes: 86958dcc5a ("mmc: dw_mmc-bluefield: Add driver extension")
Cc: stable@vger.kernel.org
Reviewed-by: David Woods <dwoods@mellanox.com>
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Get rid of some WARN_ON() from the ACPI code
- Staticize a symbol
- Fix MMC polarity detection
-----BEGIN PGP SIGNATURE-----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=kS/C
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"The patch hitting the MMC/SD subsystem is fixing up my own mess when
moving semantics from MMC/SD over to gpiolib. Ulf is on vacation but I
managed to reach him on chat and obtain his ACK.
The other two are early-rc fixes that are not super serious but pretty
annoying so I'd like to get rid of them.
Summary:
- Get rid of some WARN_ON() from the ACPI code
- Staticize a symbol
- Fix MMC polarity detection"
* tag 'gpio-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
mmc: core: don't override the CD GPIO level when "cd-inverted" is set
gpio: pca953x: Make symbol 'pca953x_i2c_regmap' static
gpiolib-acpi: Remove unnecessary WARN_ON from acpi_gpiochip_free_interrupts
We need to handle mmc_of_parse() errors during probe.
This finally fixes the wifi regression on Raspberry Pi 3 series.
In error case the wifi chip was permanently in reset because of
the power sequence depending on the deferred probe of the GPIO expander.
Fixes: b580c52d58 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because the irq was requested through device managed resources API
(devm_request_threaded_irq()) it was freed after meson_mmc_remove()
completion, thus after mmc_free_host() has reclaimed meson_host memory.
As this irq is IRQF_SHARED, while using CONFIG_DEBUG_SHIRQ, its handler
get called by free_irq(). So meson_mmc_irq() was called after the
meson_host memory reclamation and was using invalid memory.
We ended up with the following scenario:
device_release_driver()
meson_mmc_remove()
mmc_free_host() /* Freeing host memory */
...
devres_release_all()
devm_irq_release()
__free_irq()
meson_mmc_irq() /* Uses freed memory */
To avoid this, the irq is released in meson_mmc_remove() and in
mseon_mmc_probe() error path before mmc_free_host() gets called.
Reported-by: Elie Roudninski <xademax@gmail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 961de0a856 ("mmc: sdhci-omap: Workaround errata regarding
SDR104/HS200 tuning failures (i929)") added a select on TI_SOC_THERMAL
for the driver to get temperature for tuning.
However, this causes the following warning on keystone_defconfig because
keystone does not support TI_SOC_THERMAL:
"WARNING: unmet direct dependencies detected for TI_SOC_THERMAL"
Fix this by changing the select to imply.
Fixes: 961de0a856 ("mmc: sdhci-omap: Workaround errata regarding
SDR104/HS200 tuning failures (i929)")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Borislav Petkov <bp@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After 'commit 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without
CONFIG_PCI set")' dependencies on CONFIG_PCI that previously were
satisfied implicitly through dependencies on CONFIG_ACPI have to be
specified directly. This driver relies on IOSF_MBI and IOSF_MBI depends
on PCI. For this reason, add a direct dependency to CONFIG_PCI here.
Fixes: 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device
tree") gpiolib-of parses the "cd-gpios" property and flips the polarity
if "cd-inverted" is also set. This results in the "cd-inverted" property
being evaluated twice, which effectively makes it a no-op:
- first in drivers/gpio/gpiolib-of.c (of_xlate_and_get_gpiod_flags) when
setting up the CD GPIO
- then again in drivers/mmc/core/slot-gpio.c (mmc_gpio_get_cd) when
reading the CD GPIO value at runtime
On boards which are using device-tree with the "cd-inverted" property
being set any inserted card are not detected anymore. This is due to the
MMC core treating the CD GPIO with the wrong polarity.
Disable "override_cd_active_level" for the card detection GPIO which is
parsed using mmc_of_parse. This fixes SD card detection on the boards
which are currently using the "cd-inverted" device-tree property (tested
on Meson8b Odroid-C1 and Meson8b EC-100).
This does not remove the CD GPIO inversion logic from the MMC core
because there's at least one driver (sdhci-pci-core for Intel BayTrail
based boards) which still passes "override_cd_active_level = true" to
mmc_gpiod_request_cd(). Due to lack of hardware for testing this is left
untouched.
In the future the GPIO inversion logic for both, card and read-only
detection can be removed once no driver is using it anymore.
Fixes: 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Loys Ollivier <loys.ollivier@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver
-----BEGIN PGP SIGNATURE-----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=mB5P
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"This time, this pull request contains changes crossing subsystems and
archs/platforms, which is mainly because of a bigger modernization of
moving from legacy GPIO to GPIO descriptors for MMC (by Linus
Walleij).
Additionally, once again, I am funneling changes to
drivers/misc/cardreader/* and drivers/memstick/* through my MMC tree,
mostly due to that we lack a maintainer for these.
Summary:
MMC core:
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver"
* tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (99 commits)
mmc: mediatek: Add MMC_CAP_SDIO_IRQ support
mmc: renesas_sdhi_internal_dmac: Whitelist r8a774c0
dt-bindings: mmc: renesas_sdhi: Add r8a774c0 support
mmc: core: Cleanup BKOPS support
mmc: core: Drop redundant check in mmc_send_hpi_cmd()
mmc: sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures (i929)
dt-bindings: sdhci-omap: Add note for cpu_thermal
mmc: sdhci-acpi: Disable LED control for Intel BYT-based controllers
mmc: sdhci-pci: Disable LED control for Intel BYT-based controllers
mmc: sdhci: Add quirk to disable LED control
mmc: mmci: add variant property to set command stop bit
misc: alcor_pci: fix spelling mistake "invailid" -> "invalid"
mmc: meson-gx: add signal resampling
mmc: meson-gx: align default phase on soc vendor tree
mmc: meson-gx: remove useless lock
mmc: meson-gx: make sure the descriptor is stopped on errors
mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver
dt-bindings: mmc: sdhci-of-arasan: Add deprecated message for AM65
dt-bindings: mmc: sdhci-am654: Document bindings for the host controllers on TI's AM654 SOCs
mmc: sdhci-msm: avoid unused function warning
...
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
We need r8a774c0 to be whitelisted for SDHI to work on the RZ/G2E,
but we don't care about the revision of the SoC, so just whitelist
the generic part number.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's been ~6 years ago since we introduced the BKOPS support for eMMC
cards. The current code is a bit messy and primarily that's because it
prepares to support running BKOPS in an asynchronous mode. However, that
mode has never been fully implemented/enabled. Instead BKOPS is always
executed in synchronously, when the card has reported an urgent BKOPS
level.
For these reasons, let's make the code more readable by dropping the unused
parts. Let's also rename mmc_start_bkops() to mmc_run_bkops(), as to make
it more descriptive.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no point checking if HPI is supported in mmc_send_hpi_cmd() as
mmc_interrupt_hpi(), which is the only caller, already checks if HPI has
been enabled. Therefore, let's drop the check and the corresponding error
path.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMCs from Micron have been reported to need ~800 ms timeout, while
enabling the CACHE ctrl after running sudden power failure tests. The
needed timeout is greater than what the card specifies as its generic CMD6
timeout, through the EXT_CSD register, hence the problem.
Normally we would introduce a card quirk to extend the timeout for these
specific Micron cards. However, due to the rather complicated debug process
needed to find out the error, let's simply use a minimum timeout of 1600ms,
the double of what has been reported, for all cards when enabling CACHE
ctrl.
Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 5320226a05 ("mmc: core: Disable HPI for certain Hynix eMMC
cards"), then intent was to prevent HPI from being used for some eMMC
cards, which didn't properly support it. However, that went too far, as
even BKOPS and CACHE ctrl became prevented. Let's restore those parts and
allow BKOPS and CACHE ctrl even if HPI isn't supported.
Fixes: 5320226a05 ("mmc: core: Disable HPI for certain Hynix eMMC cards")
Cc: Pratibhasagar V <pratibha@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During a re-initialization of the eMMC card, we may fail to re-enable HPI.
In these cases, that isn't properly reflected in the card->ext_csd.hpi_en
bit, as it keeps being set. This may cause following attempts to use HPI,
even if's not enabled. Let's fix this!
Fixes: eb0d8f135b ("mmc: core: support HPI send command")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While booting with rootfs on MMC, the following warning is encountered
on OMAP4430:
omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536]
This is because the DMA engine has a default maximum segment size of 64K
but HSMMC sets:
mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
mmc->max_seg_size = mmc->max_req_size;
which ends up telling the block layer that we support a maximum segment
size of 65535*512, which exceeds the advertised DMA engine capabilities.
Fix this by clamping the maximum segment size to the lower of the
maximum request size and of the DMA engine device used for either DMA
channel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the SDMMC pads auto calibration values parsed from
devicetree are assigned incorrectly. This patch fixes it.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Fixes: 51b77c8ea7 ("mmc: tegra: Program pad autocal offsets from dt")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
V4_MODE is Bit-15 of SDHCI_HOST_CONTROL2 register.
Need to perform word access to this register.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Fixes: b3f80b434f ("mmc: sdhci: Add sd host v4 mode")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i929 in certain OMAP5/DRA7XX/AM57XX silicon revisions
(SPRZ426D - November 2014 - Revised February 2018 [1]) mentions
unexpected tuning pattern errors. A small failure band may be present
in the tuning range which may be missed by the current algorithm.
Furthermore, the failure bands vary with temperature leading to
different optimum tuning values for different temperatures.
As suggested in the related Application Report (SPRACA9B - October 2017
- Revised July 2018 [2]), tuning should be done in two stages.
In stage 1, assign the optimum ratio in the maximum pass window for the
current temperature. In stage 2, if the chosen value is close to the
small failure band, move away from it in the appropriate direction.
References:
[1] http://www.ti.com/lit/pdf/sprz426
[2] http://www.ti.com/lit/pdf/SPRACA9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel BYT-based controllers do not have a LED signal line. Nevertheless
sdhci_led_control() takes more than twice as long as sdhci_send_command(),
even though it does nothing. Use the new SDHCI_QUIRK_NO_LED quirk to
disable LED control for Intel BYT-based controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel BYT-based controllers do not have a LED signal line. Nevertheless
sdhci_led_control() takes more than twice as long as sdhci_send_command(),
even though it does nothing. Use the new SDHCI_QUIRK_NO_LED quirk to
disable LED control for Intel BYT-based controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host controllers may not have a LED signal line, whereas the register
updates to control the non-existent LED can be relatively time consuming.
Add a quirk to disable LED control.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On cmd12 (STOP_TRANSMISSION), STM32 sdmmc variant needs to set
cmdstop bit in command register. The CPSM ("Command Path State Machine")
treats the command as a Stop Transmission command and signals
abort to the DPSM ("Data Path State Machine").
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With some eMMC devices, there is still issues with the new phase
settings. Enabling signal resampling seems to solve the problem
for these.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Align the default Core and Tx phase with the SoC vendor tree.
Even if the Tx phase is different from what the documentation
recommends, it seems to provide better results.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The spinlock is only used within the irq handler so it does not
seem very useful.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On errors, if we don't stop the descriptor chain, it may continue to
run and raise IRQ after we have called mmc_request_done(). This is bad
because we won't be able to get cmd anymore and properly deal with the
IRQ.
This patch makes sure the descriptor chain is stopped before
calling mmc_request_done()
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The host controllers on TI's AM654 SOCs are not compatible with
the phy and consumer model of the sdhci-of-arasan driver. It turns out
that for optimal operation at higher speeds, a special tuning procedure
needs to be implemented which involves configuration of platform
specific phy registers.
Therefore, branch out to a new sdhci_am654 driver and add the phy
register space with all phy configurations to it. Populate AM654
specific callbacks to sdhci_ops and add SDHCI_QUIRKS wherever
applicable.
Only add support for upto High Speed for SD card and upto DDR52 speed
mode for eMMC. Higher speeds will be added in subsequent patches.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newly added sdhci_msm_restore_sdr_dll_config() function is only called
if CONFIG_PM is enabled:
drivers/mmc/host/sdhci-msm.c:1050:12: error:
'sdhci_msm_restore_sdr_dll_config' defined but not used
[-Werror=unused-function]
Better remove the incorrect #ifdef altogether and just use __maybe_unused,
which is harder to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Always check the wait condition before returning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Always check the wait condition before returning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mmc/host/alcor.c: In function 'alcor_data_set_dma':
drivers/mmc/host/alcor.c:124:12: warning:
variable 'len' set but not used [-Wunused-but-set-variable]
drivers/mmc/host/alcor.c:648:15: warning:
variable 'clock_out' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a spelling mistake in a pr_warn message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The rtsx USB parent device, has logic to detect when a card is inserted
into the card slot. Although, the logic can't detect when a card is
removed. This makes things a bit tricky, which is why the current method is
simply to turn on MMC_CAP_NEEDS_POLL during probe.
Using MMC_CAP_NEEDS_POLL means lots of energy being wasted, as the mmc host
becomes runtime resumed frequently by the mmc core, while it polls for new
cards being inserted.
To address this problem, let's start relying on that the rtsx USB driver
runtime resumes its child device, which is the rtsx_usb_sdmmc device, when
it detects that a new card being inserted.
This means dropping MMC_CAP_NEEDS_POLL from being set during probe. Instead
let's implement a ->runtime_resume() callback to schedule a detect work and
to set MMC_CAP_NEEDS_POLL. In this way, polling is enabled as long as there
is card inserted, thus we can rely on the mmc core to detect also when the
card becomes removed.
Furthermore, to avoid polling forever after a card has been removed, let's
implement a ->runtime_suspend() callback and make it clear
MMC_CAP_NEEDS_POLL.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
The current implementation uses the runtime PM autosuspend feature with a
default timeout set to 50ms. This really doesn't makes sense, as it's a USB
driven host device, which needs it rtsx USB device (parent device) to be
runtime resumed to provide power to the card.
In practise, using the autosuspend or any async runtime PM suspend method,
means unnecessary delaying the host device and thus the parent, to be
runtime suspended when a card is removed/powered off. For this reasons,
let's simply drop the support for runtime PM autosuspend and tell the mmc
core to use synced runtime PM suspend methods, via setting
MMC_CAP_SYNC_RUNTIME_PM during probe.
Moreover, as the mmc core nowadays deploys runtime PM reference counting of
the mmc host device, convert ->set_ios() to use the more lightweight
pm_runtime_get_noresume() and pm_runtime_put_noidle() APIs.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
In case the card has been powered off, it seems silly to continue to allow
the led to be updated. Instead let's forbid that, as it enables us to
prevent runtime resuming the device and thus avoids wasting energy.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
To allow mmc host drivers to inform the mmc core about rather using
pm_runtime_put_sync_suspend() instead of pm_runtime_put_autosuspend(),
let's introduce MMC_CAP_SYNC_RUNTIME_PM.
This is especially useful for those mmc host drivers that don't benefit
from using the runtime PM autosuspend feature. Typically this is those that
relies on parent devices to power the card via runtime PM, like some USB
host drivers for example.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
The Clock Data Recovery (CDR) circuit allows to automatically adjust
the RX sampling-point/phase for high frequency cards (SDR104, HS200...).
CDR is automatically enabled during DLL configuration.
However, according to the APQ8016 reference manual, this function
must be disabled during TX and tuning phase in order to prevent any
interferences during tuning challenges and unexpected phase alteration
during TX transfers.
This patch enables/disables CDR according to the current transfer mode.
This fixes sporadic write transfer issues observed with some SDR104 and
HS200 cards.
Inspired by sdhci-msm downstream patch:
https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/432516/
Reported-by: Leonid Segal <leonid.s@variscite.com>
Reported-by: Manabu Igusa <migusa@arrowjapan.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver provides support for Alcor Micro AU6601 and AU6621
SD/MMC controller.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the mmc max-frequency device property for Intel BYT-based
host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All host drivers are converted to look up GPIO descriptors
from device tree, ACPI or machine descriptor tables, so now
we can delete the legacy GPIO handling using hardcoded GPIO
numbers from the kernel.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After converting the PXA driver to use GPIO descriptors for
card detect and write protect it is relatively simple to
convert it to also use a descriptor for getting the optional
power control GPIO.
The polarity inversion flag can also go away from the platform
data since this is indicated in the GPIO machine descriptor
table.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This deletes the code dealing with handling card detect
and write protect passed in as platform data and makes
the host rely on just GPIO descriptors.
The card read only inversion flag has to be kept around
for now, as the core cannot handle the inversion flags
on the descriptors yet.
Since we can now rely on the descriptors to have the
right polarity, we set the "override_active_level" to
false in mmc_gpiod_request_cd() and mmc_gpiod_request_ro().
Cc: Daniel Mack <daniel@zonque.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This implements the code path for the PXAMCI hostso that
it can retrieve GPIO descriptors rather than use the
global GPIO numberspace for GPIO lines. If the GPIO
descriptor is present, it will take precedence and get
used in place of the platform data GPIO number.
We move the code around a bit so we request the card
detect first and the write protect second.
We keep the code setting the host flag for the write
protect polarity inversion semantics since the slot
GPIO core needs to be refactored to deal with this
before we can get rid of this.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Simplify things by making the S3CMCI driver just use
slot GPIO with descriptors instead of passing around the
global GPIO numbers that we want to get rid of.
Getting the names of the GPIO chips into the machine
descriptor tables was a bit of a challenge but I think
I have them right.
The platform data supports passing in inversion flags, but
no platform is using them, and it is highly unlikely
that we will add more, so drop them. The long term plan
is to let the inversion flags on the GPIO machine
descriptor do the job.
The lines are flagged as GPIO_ACTIVE_[LOW|HIGH] as that is
what they are, and since we can now rely on the descriptors
to have the right polarity, we set the
"override_active_level" to false in mmc_gpiod_request_cd()
and mmc_gpiod_request_ro().
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TMIO MMC driver was passing global GPIO numbers around for
card detect. It turns out only one single board in the kernel
was actually making use of this feature so it is pretty easy
to convert the driver to use only GPIO descriptors.
The lines are flagged as GPIO_ACTIVE_[LOW|HIGH] as that is
what they are, and since we can now rely on the descriptors
to have the right polarity, we set the
"override_active_level" to false in mmc_gpiod_request_cd()
and mmc_gpiod_request_ro().
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch the SPI MMC driver to use GPIO descriptors internally
and just look those up using the standard slot GPIO
functions mmc_gpiod_request_cd() and mmc_gpiod_request_ro().
Make sure to request index 0 and 1 in accordance with the
SPI MMC DT binding, and add the same GPIOs in machine
descriptor tables on all boards that use SPI MMC in
board files.
The lines are flagged as GPIO_ACTIVE_[LOW|HIGH] as that is
what they are, and since we can now rely on the descriptors
to have the right polarity, we set the
"override_active_level" to false in mmc_gpiod_request_cd()
and mmc_gpiod_request_ro().
Cc: Hartley Sweeten <hsweeten@visionengravers.com> # Vision EP9307
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_kasprintf() may return NULL on failure of internal allocation thus
the assignments to init.name are not safe if not checked. On error
meson_mx_mmc_register_clks() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This was a SoC issue on LX2160A Rev1.0.
eSDHC_DLLCFG1[DLL_PD_PULSE_STRETCH_SEL] must be set to 0 to
get 4 delay cells in the pulse width detection logic for eMMC
HS400 mode. Otherwise it would cause unexpected HS400 issue.
This patch is to clear this bit always for affected SoC when
reset for all, since this bit doesn't affect other speed modes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently only LX2160A eSDHC supports eMMC HS400. According to
a large number of tests, eMMC HS400 failed to work at 150MHz,
and for a few boards failed to work at 175MHz. But eMMC HS400
worked fine on 200MHz. We hadn't found the root cause but
setting eSDHC_DLLCFG0[DLL_FREQ_SEL] = 0 using slow delay chain
seemed to resovle this issue. Let's use this as fixup for now.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are timing violations in case of few division ratio options
are selected for card clock frequency. prescaler*divisor options
/3,/5,/6,/7,/9,/10,/11,/13,/14 and /15 are not available in LX2
Rev1.0. prescaler*divisor options /4,/8 and /12 only available in
LX2 Rev1.0. Applicable only for HS400 mode. so by add the erratum
A011334 support to limit the prescaler*divisor in LX2 REV1.0
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1. Perform the Tuning Process at the HS400 target operating frequency.
Latched the clock division value.
2. if read transaction, then set the SDTIMNGCTL[FLW_CTL_BG].
3. Switch to High Speed mode and then set the card clock frequency to
a value not greater than 52Mhz
4. Clear TBCTL[TB_EN],tuning block enable bit.
5. Change to 8 bit DDR Mode
6. Switch the card to HS400 mode.
7. Set TBCTL[TB_EN], tuning block enable bit.
8. Clear SYSCTL[SDCLKEN]
9. Wait for PRSSTAT[SDSTB] to be set
10. Change the clock division to latched value.Set TBCTL[HS 400 mode]
and Set SDCLKCTL[CMD_CLK_CTRL]
11. Set SYSCTL[SDCLKEN]
12. Wait for PRSSTAT[SDSTB] to be set
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
15. Set TBCTL[HS400_WNDW_ADJUST]
16. Again clear SYSCTL[SDCLKEN]
17. Wait for PRSSTAT[SDSTB] to be set
18. Set ESDHCCTL[FAF]
19. Wait for ESDHCCTL[FAF] to be cleared
20. Set SYSCTL[SDCLKEN]
21. Wait for PRSSTAT[SDSTB] to be set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC controllers need specific settings for HS400 mode before the
speed mode can be switched to DDR mode, during the HS400 initialization
sequence. For that reason, let's introduce a new host callback,
->hs400_prepare_ddr() and invoked it just before switching to DDR mode.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_execute_tuning() function has assignment of
private pointers multiple times. Remove the redundant assignment.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TRM (SPRUIC2C - January 2017 - Revised May 2018 [1]) forbids
assertion of data reset while tuning is happening. Implement a
platform specific callback that takes care of this condition.
[1] http://www.ti.com/lit/pdf/spruic2 Section 25.5.1.2.4
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As reported by Aaro, the JZ4740 MMC driver throws a warning when the kernel
is built without preemption (CONFIG_PREEMPT_NONE=y).
[ 16.461094] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 567 host->next_data.cookie 568
[ 16.473120] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 568 host->next_data.cookie 569
[ 16.485144] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 569 host->next_data.cookie 570
[ 16.497170] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 570 host->next_data.cookie 571
The problem seems to be related to how pre_req/post_req is implemented.
Currently, it seems the driver expects jz4740_mmc_prepare_dma_data() to be
called with monotonically increasing host_cookie values, which is wrong.
Moreover, the implementation is overly complicated, keeping track of
unneeded "next cookie" state.
So, instead of attempting to fix the current pre_req/post_req
implementation, this commit refactors the driver, dropping the state,
following other drivers such as dw_mmc and sdhci.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Mathieu Malaterre <malat@debian.org>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refer to "4.15 set block count command" of sd specification:
Host needs to issue CMD12 if any error is detected in
the CMD18 and CMD25 operations.
In sbc case, the data->stop is fill by framework.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some variants (namely Renesas SDHI) have bits in the STATS and IRQ_MASK
registers which are 'always 1' and should be written as such. Introduce
a seperate mask for this and apply it whenever such a register is
written.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Renesas BSP confirms that H3 ES1.x and M3-W ES1.[012] do not
properly support HS400. Add a quirk to indicate this and disable HS400
in the MMC capabilities if the quirk is set.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was though all ES revisions of H3 and M3-W SoCs required the
TMIO_MMC_HAVE_4TAP_HS400 flag. Recent datasheet updates tells us this is
not true, only early ES revisions of the SoC do.
Since quirk matching based on ES revisions is now used to handle the
flag it's possible to align all Gen3 compatibility properties. This will
allow later ES revisions of H3 and M3-W to use the correct 8-tap HS400
mode.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Latest datasheet makes it clear that not all ES revisions of the H3 and
M3-W have the 4-tap HS400 mode quirk, currently the quirk is set
unconditionally for these two SoCs. Prepare to handle the quirk based on
SoC revision instead of compatibility value by using soc_device_match()
and set the TMIO_MMC_HAVE_4TAP_HS400 flag explicitly.
The reason for adding a new quirks struct instead of just a flag is that
looking ahead it seems more quirks needs to be handled in a SoC revision
basis.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initial value of the interrupt mask register may be different from
the H/W manual at the startup of the kernel by setting from the
bootloader. Since the error interrupts may be unmasked, the driver sets
initial value.
The initial value is only known for R-Car Gen2 and Gen3 platforms so
limit the initialization to those platforms.
Based on work from Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD / MMC did not operate properly when suspend transition failed.
Because the SCC was not reset at resume, issue of the command failed.
Call the host specific reset function and reset the hardware in order to
add reset of SCC. This change also fixes tuning on some stubborn cards
on Gen2.
Based on work from Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On runtime power management resume, the host clock needs to be
enabled before calling tmio_mmc_reset. If the mmc device has a power
domain entry, the host clock is enabled via genpd_runtime_resume,
running before tmio_mmc_host_runtime_resume. If the mmc device has no
power domain entry, however, genpd_runtime_resume is not called. This
patch changes tmio_mmc_host_runtime_resume to enable the host clock
before calling tmio_mmc_reset.
Based on work from Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only user was converted to fill a sbc command which is the proper
way to do it because of AutoCMD23 feature of some hosts.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case dmaengine_prep_slave_sg fails we need to call dma_unmap_sg.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are two variables len within bcm2835_prepare_dma. So rename the
result of dma_map_sg to sg_len. While we are at this add a bail out to
simplify the following change.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's better to make sure that the timeout work is really terminated
before calling mmc_request_done.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are two accesses on the data requests which are not protected by
the mutex. So fix this accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to release the slave DMA channel during driver unload.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
Link: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bcm2835 mmc host tends to lock up for unknown reason so reset it on
timeout. The upper mmc block layer tries retransimitting with single
blocks which tends to work out after a long wait.
This is better than giving up and leaving the machine broken for no
obvious reason.
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Simplify things by making the i.MX SDHCI driver just use
slot GPIO with descriptors instead of passing around the global
GPIO numbers that we want to get rid of.
As it turns out, just one single board is using the platform
data to pass in GPIOs numbers for CD and WP, so we augment this
to use a machine descriptor table instead.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The power GPIO line is passed with inversion flags and all from
the platform data. Switch to using an optional GPIO descriptor and
use this to switch the power.
Augment the only boardfile to pass in the proper "power" descriptor
in the GPIO descriptor machine table instead.
As the GPIO handling is now much simpler, we can cut down on some
overhead code.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modifty the JZ4740 driver to retrieve card detect and write
protect GPIO pins from GPIO descriptors instead of hard-coded
global numbers. Augment the only board file using this in the
process and cut down on passed in platform data.
Preserve the code setting the caps2 flags for CD and WP
as active low or high since the slot GPIO code currently
ignores the gpiolib polarity inversion semantice and uses
the raw accessors to read the GPIO lines, but set the right
polarity flags in the descriptor table for jz4740.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The use of string pointers in the MMC slot GPIO context is
pretty dubious, allocating some 2*len extra bytes for each
label of the ro and wp pins.
Tidy this up using kasprintf() with dynamic allocation of
labels for these strings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On few SDHCI-MSM controllers, the host controller's clock tuning
circuit may go out of sync if controller clocks are gated which
eventually will result in data CRC, command CRC/timeout errors.
To overcome this h/w limitation, the DLL needs to be re-initialized
and restored with its old settings once clocks are ungated.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the host controller supports auto-commands then enable the auto-command
error interrupt and handle it. In the case of auto-CMD23, the error is
treated the same as manual CMD23 error. In the case of auto-CMD12,
commands-during-transfer are not permitted, so the error handling is
treated the same as a data error.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_ACMD12_ERR register is used for auto-CMD23 and auto-CMD12
errors, as is the SDHCI_INT_ACMD12ERR interrupt bit. Rename them to
SDHCI_AUTO_CMD_STATUS and SDHCI_INT_AUTO_CMD_ERR respectively.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Existing data command CRC error handling is non-standard and does not work
with some Intel host controllers. Specifically, the assumption that the host
controller will continue operating normally after the error interrupt,
is not valid. Change the driver to handle the error in the same manner
as a data CRC error, taking care to ensure that the data line reset is
done for single or multi-block transfers, and it is done before
unmapping DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Whitelist R8A77990 E3 SoC in the SDHI driver. The SDHI core
present in the SoC is an 8tap variant of the Gen3 SDHI core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The manual does not contain information that a wait is needed in the
tuning process, this might be a leftover from early development.
Removing the wait don't have any effect on operation so delete the wait
to shorten the initialization time.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[Niklas: fixup commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver sets an incorrect clock and depends on the clock driver
knowledge of this incorrect setting to still set a 200Mhz SDn clock.
Instead of spreading the workaround between the two drivers the clock
driver should be made aware of the ES versions where the special clock
handling is needed no need to keep this workaround in the SDHI driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The reason of including <linux/bitops.h> here is just for BIT() and
GENMASK() macros.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function sdhci_allocate_bounce_buffer() always return zero at
present, so there's no need to have a return value, that will also make
error path easier.
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHI/MMC controller in the RZ/A2 is almost the same as R-Car gen3, but
with some minor differences.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On our AT91SAM9260 board we use the same sdio bus for wifi and for the
sd card slot. This caused the atmel-mci to give the following splat on
the serial console:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 538 at drivers/mmc/host/atmel-mci.c:859 atmci_send_command+0x24/0x44
Modules linked in:
CPU: 0 PID: 538 Comm: mmcqd/0 Not tainted 4.14.76 #14
Hardware name: Atmel AT91SAM9
[<c000fccc>] (unwind_backtrace) from [<c000d3dc>] (show_stack+0x10/0x14)
[<c000d3dc>] (show_stack) from [<c0017644>] (__warn+0xd8/0xf4)
[<c0017644>] (__warn) from [<c0017704>] (warn_slowpath_null+0x1c/0x24)
[<c0017704>] (warn_slowpath_null) from [<c033bb9c>] (atmci_send_command+0x24/0x44)
[<c033bb9c>] (atmci_send_command) from [<c033e984>] (atmci_start_request+0x1f4/0x2dc)
[<c033e984>] (atmci_start_request) from [<c033f3b4>] (atmci_request+0xf0/0x164)
[<c033f3b4>] (atmci_request) from [<c0327108>] (mmc_start_request+0x280/0x2d0)
[<c0327108>] (mmc_start_request) from [<c032800c>] (mmc_start_areq+0x230/0x330)
[<c032800c>] (mmc_start_areq) from [<c03366f8>] (mmc_blk_issue_rw_rq+0xc4/0x310)
[<c03366f8>] (mmc_blk_issue_rw_rq) from [<c03372c4>] (mmc_blk_issue_rq+0x118/0x5ac)
[<c03372c4>] (mmc_blk_issue_rq) from [<c033781c>] (mmc_queue_thread+0xc4/0x118)
[<c033781c>] (mmc_queue_thread) from [<c002daf8>] (kthread+0x100/0x118)
[<c002daf8>] (kthread) from [<c000a580>] (ret_from_fork+0x14/0x34)
---[ end trace 594371ddfa284bd6 ]---
This is:
WARN_ON(host->cmd);
This was fixed on our board by letting atmci_request_end determine what
state we are in. Instead of unconditionally setting it to STATE_IDLE on
STATE_END_REQUEST.
Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit removes the unnecessary of-node check since the
dw_mci_bluefield_match[] structure has only one entry.
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We observed some premature timeouts on a virtualization platform, the log
is like this:
case 1:
[159525.255629] mmc1: Internal clock never stabilised.
[159525.255818] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[159525.256049] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001002
...
[159525.257205] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
From the clock control register dump, we are pretty sure the clock was
stablized.
case 2:
[ 914.550127] mmc1: Reset 0x2 never completed.
[ 914.550321] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 914.550608] mmc1: sdhci: Sys addr: 0x00000010 | Version: 0x00001002
After checking the sdhci code, we found the timeout check actually has a
little window that the CPU can be scheduled out and when it comes back,
the original time set or check is not valid.
Fixes: 5a436cc0af ("mmc: sdhci: Optimize delay loops")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 7d33c35815 ("mmc: sdhci-omap: Workaround for Errata i802")
disabled DCRC interrupts during tuning. This write to the interrupt
enable register gets overwritten in sdhci_prepare_data() and the
interrupt is not in fact disabled. Fix this by disabling the interrupt
in the host->ier variable.
Fixes: 7d33c35815 ("mmc: sdhci-omap: Workaround for Errata i802")
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwEZdIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAlQH/19oax2Za3IPqF4X
DM3lal5M6zlUVkoYstqzpbR3MqUwgEnMfvoeMDC6mI9N4/+r2LkV7cRR8HzqQCCS
jDfD69IzRGb52VSeJmbOrkxBWsR1Nn0t4Z3rEeLPxwaOoNpRc8H973MbAQ2FKMpY
S4Y3jIK1dNiRRxdh52NupVkQF+djAUwkBuVk/rrvRJmTDij4la03cuCDAO+Di9lt
GHlVvygKw2SJhDR+z3ArwZNmE0ceCcE6+W7zPHzj2KeWuKrZg22kfUD454f2YEIw
FG0hu9qecgtpYCkLSm2vr4jQzmpsDoyq3ZfwhjGrP4qtvPC3Db3vL3dbQnkzUcJu
JtwhVCE=
=O1q1
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc5' into for-4.21/block
Pull in v4.20-rc5, solving a conflict we'll otherwise get in aio.c and
also getting the merge fix that went into mainline that users are
hitting testing for-4.21/block and/or for-next.
* tag 'v4.20-rc5': (664 commits)
Linux 4.20-rc5
PCI: Fix incorrect value returned from pcie_get_speed_cap()
MAINTAINERS: Update linux-mips mailing list address
ocfs2: fix potential use after free
mm/khugepaged: fix the xas_create_range() error path
mm/khugepaged: collapse_shmem() do not crash on Compound
mm/khugepaged: collapse_shmem() without freezing new_page
mm/khugepaged: minor reorderings in collapse_shmem()
mm/khugepaged: collapse_shmem() remember to clear holes
mm/khugepaged: fix crashes due to misaccounted holes
mm/khugepaged: collapse_shmem() stop if punched or truncated
mm/huge_memory: fix lockdep complaint on 32-bit i_size_read()
mm/huge_memory: splitting set mapping+index before unfreeze
mm/huge_memory: rename freeze_page() to unmap_page()
initramfs: clean old path before creating a hardlink
kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace
psi: make disabling/enabling easier for vendor kernels
proc: fixup map_files test on arm
debugobjects: avoid recursive calls with kmemleak
userfaultfd: shmem: UFFDIO_COPY: set the page dirty if VM_WRITE is not set
...
Since v2.6.22 or so there has been reports [1] about OMAP MMC being
broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage
seems to have been caused by commit 46a6730e3f ("mmc-omap: Fix
omap to use MMC_POWER_ON") that changed clock enabling to be done
on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
the hardware doesn't seem to like it and the MMC just stops responding.
Fix by memorizing the power mode and do the init only when necessary.
Before the patch (on Palm TE):
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmci-omap mmci-omap.0: command timeout (CMD8)
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmcblk0: recovery failed!
print_req_error: I/O error, dev mmcblk0, sector 0
Buffer I/O error on dev mmcblk0, logical block 0, async page read
mmcblk0: unable to read partition table
After the patch:
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmcblk0: p1
The patch is based on a fix and analysis done by Ladislav Michl.
Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
and OMAP2420 (Nokia N810).
[1] https://marc.info/?t=123175197000003&r=1&w=2
Fixes: 46a6730e3f ("mmc-omap: Fix omap to use MMC_POWER_ON")
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Andrzej Zaborowski <balrogg@gmail.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When sending out CMD23 in the blk preparation, the comment there
rightfully says:
* However, it is not sufficient to just send CMD23,
* and avoid the final CMD12, as on an error condition
* CMD12 (stop) needs to be sent anyway. This, coupled
* with Auto-CMD23 enhancements provided by some
* hosts, means that the complexity of dealing
* with this is best left to the host. If CMD23 is
* supported by card and host, we'll fill sbc in and let
* the host deal with handling it correctly.
Let's do this behaviour for RPMB as well, and not send CMD23
independently. Otherwise IP cores (like Renesas SDHI) may timeout
because of automatic CMD23/CMD12 handling.
Reported-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GLK firmware can indicate that the tuning value will be restored after
runtime suspend, but not actually do that. Add a workaround that detects
such cases, and lets the driver do re-tuning instead.
Reported-by: Anisse Astier <anisse@astier.eu>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Problem:
The card detect IRQ does not work with modern BIOS (that want
to use _DSD to provide the card detect GPIO to the driver).
Details:
The mmc core provides the mmc_gpiod_request_cd() API to let host drivers
request the gpio descriptor for the "card detect" pin.
This pin is specified in the ACPI for the SDHC device:
* Either as a resource using _CRS. This is a method used by legacy BIOS.
(The driver needs to tell which resource index).
* Or as a named property ("cd-gpios"/"cd-gpio") in _DSD (which internally
points to an entry in _CRS). This way, the driver can lookup using a
string. This is what modern BIOS prefer to use.
This API finally results in a call to the following code:
struct gpio_desc *acpi_find_gpio(..., const char *con_id,...)
{
...
/* Lookup gpio (using "<con_id>-gpio") in the _DSD */
...
if (!acpi_can_fallback_to_crs(adev, con_id))
return ERR_PTR(-ENOENT);
...
/* Falling back to _CRS is allowed, Lookup gpio in the _CRS */
...
}
Note that this means that if the ACPI has _DSD properties, the kernel
will never use _CRS for the lookup (Because acpi_can_fallback_to_crs()
will always be false for any device hat has _DSD entries).
The SDHCI driver is thus currently broken on a modern BIOS, even if
BIOS provides both _CRS (for index based lookup) and _DSD entries (for
string based lookup). Ironically, none of these will be used for the
lookup currently because:
* Since the con_id is NULL, acpi_find_gpio() does not find a matching
entry in DSDT. (The _DSDT entry has the property name = "cd-gpios")
* Because ACPI contains DSDT entries, thus acpi_can_fallback_to_crs()
returns false (because device properties have been populated from
_DSD), thus the _CRS is never used for the lookup.
Fix:
Try "cd" for lookup in the _DSD before falling back to using NULL so
as to try looking up in the _CRS.
I've tested this patch successfully with both Legacy BIOS (that
provide only _CRS method) as well as modern BIOS (that provide both
_CRS and _DSD). Also the use of "cd" appears to be fairly consistent
across other users of this API (other MMC host controller drivers).
Link: https://lkml.org/lkml/2018/9/25/1113
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: f10e4bf663 ("gpio: acpi: Even more tighten up ACPI GPIO lookups")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace the lock in mmc_blk_data that is only used through a pointer
in struct mmc_queue and to protect fields in that structure with
an actual lock in struct mmc_queue.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
mmc uses the block layer struct request pointer to indirect their own
lock to the mmc_queue structure, given that the original lock isn't
reachable outside of block.c. Add a lock pointer to struct mmc_queue
instead and stop overriding the block layer lock which protects fields
entirely separate from the mmc use.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge three functions initializing the queue into a single one, and drop
an unused argument for it.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull perf updates from Ingo Molnar:
"The main updates in this cycle were:
- Lots of perf tooling changes too voluminous to list (big perf trace
and perf stat improvements, lots of libtraceevent reorganization,
etc.), so I'll list the authors and refer to the changelog for
details:
Benjamin Peterson, Jérémie Galarneau, Kim Phillips, Peter
Zijlstra, Ravi Bangoria, Sangwon Hong, Sean V Kelley, Steven
Rostedt, Thomas Gleixner, Ding Xiang, Eduardo Habkost, Thomas
Richter, Andi Kleen, Sanskriti Sharma, Adrian Hunter, Tzvetomir
Stoyanov, Arnaldo Carvalho de Melo, Jiri Olsa.
... with the bulk of the changes written by Jiri Olsa, Tzvetomir
Stoyanov and Arnaldo Carvalho de Melo.
- Continued intel_rdt work with a focus on playing well with perf
events. This also imported some non-perf RDT work due to
dependencies. (Reinette Chatre)
- Implement counter freezing for Arch Perfmon v4 (Skylake and newer).
This allows to speed up the PMI handler by avoiding unnecessary MSR
writes and make it more accurate. (Andi Kleen)
- kprobes cleanups and simplification (Masami Hiramatsu)
- Intel Goldmont PMU updates (Kan Liang)
- ... plus misc other fixes and updates"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (155 commits)
kprobes/x86: Use preempt_enable() in optimized_callback()
x86/intel_rdt: Prevent pseudo-locking from using stale pointers
kprobes, x86/ptrace.h: Make regs_get_kernel_stack_nth() not fault on bad stack
perf/x86/intel: Export mem events only if there's PEBS support
x86/cpu: Drop pointless static qualifier in punit_dev_state_show()
x86/intel_rdt: Fix initial allocation to consider CDP
x86/intel_rdt: CBM overlap should also check for overlap with CDP peer
x86/intel_rdt: Introduce utility to obtain CDP peer
tools lib traceevent, perf tools: Move struct tep_handler definition in a local header file
tools lib traceevent: Separate out tep_strerror() for strerror_r() issues
perf python: More portable way to make CFLAGS work with clang
perf python: Make clang_has_option() work on Python 3
perf tools: Free temporary 'sys' string in read_event_files()
perf tools: Avoid double free in read_event_file()
perf tools: Free 'printk' string in parse_ftrace_printk()
perf tools: Cleanup trace-event-info 'tdata' leak
perf strbuf: Match va_{add,copy} with va_end
perf test: S390 does not support watchpoints in test 22
perf auxtrace: Include missing asm/bitsperlong.h to get BITS_PER_LONG
tools include: Adopt linux/bits.h
...
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
- Introduce a host helper function to share re-tuning progress
MMC host:
- sdhci: Add support for v4 host mode
- sdhci-of-arasan: Add Support for AM654 MMC and PHY
- sdhci-sprd: Add support for Spreadtrum's host controller
- sdhci-tegra: Add support for HS400 enhanced strobe
- sdhci-tegra: Enable UHS/HS200 modes for Tegra186/210
- sdhci-tegra: Add support for HS400 delay line calibration
- sdhci-tegra: Add support for pad calibration
- sdhci-of-dwcmshc: Address 128MB DMA boundary limitation
- sdhci-of-esdhc: Add support for tuning erratum A008171
- sdhci-iproc: Add ACPI support
- mediatek: Add support for MT8183
- mediatek: Improve the support for tuning
- mediatek: Add bus clock control for MT2712
- jz4740: Add support for the JZ4725B
- mmci: Add support for the stm32 sdmmc variant
- mmci: Add support for an optional reset control
- mmci: Add some new variant specific properties/callbacks
- mmci: Re-structure DMA code to prepare for new variants
- renesas_sdhi: Add support for r8a77470, r8a7744 and r8a774a1
- renesas_sdhi_internal_dmac: Whitelist r8a77970 and r8a774a1
- tmio/uniphier-sd: Add new UniPhier SD/eMMC controller driver
- tmio/renesas_sdhi: Deal properly with SCC detection during re-tune
- tmio/renesas_sdhi: Refactor/consolidate clock management
- omap_hsmmc: Drop cover detection and some unused platform data
- dw_mmc-exynos: Enable tuning for more speed modes
- sunxi: Clarify the new timing mode and enable it for the A64 controller
- various: Convert to slot GPIO descriptors
-----BEGIN PGP SIGNATURE-----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=/4yi
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce a host helper function to share re-tuning progress
MMC host:
- sdhci: Add support for v4 host mode
- sdhci-of-arasan: Add Support for AM654 MMC and PHY
- sdhci-sprd: Add support for Spreadtrum's host controller
- sdhci-tegra: Add support for HS400 enhanced strobe
- sdhci-tegra: Enable UHS/HS200 modes for Tegra186/210
- sdhci-tegra: Add support for HS400 delay line calibration
- sdhci-tegra: Add support for pad calibration
- sdhci-of-dwcmshc: Address 128MB DMA boundary limitation
- sdhci-of-esdhc: Add support for tuning erratum A008171
- sdhci-iproc: Add ACPI support
- mediatek: Add support for MT8183
- mediatek: Improve the support for tuning
- mediatek: Add bus clock control for MT2712
- jz4740: Add support for the JZ4725B
- mmci: Add support for the stm32 sdmmc variant
- mmci: Add support for an optional reset control
- mmci: Add some new variant specific properties/callbacks
- mmci: Re-structure DMA code to prepare for new variants
- renesas_sdhi: Add support for r8a77470, r8a7744 and r8a774a1
- renesas_sdhi_internal_dmac: Whitelist r8a77970 and r8a774a1
- tmio/uniphier-sd: Add new UniPhier SD/eMMC controller driver
- tmio/renesas_sdhi: Deal properly with SCC detection during re-tune
- tmio/renesas_sdhi: Refactor/consolidate clock management
- omap_hsmmc: Drop cover detection and some unused platform data
- dw_mmc-exynos: Enable tuning for more speed modes
- sunxi: Clarify the new timing mode and enable it for the A64 controller
- various: Convert to slot GPIO descriptors"
* tag 'mmc-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (129 commits)
mmc: mediatek: drop too much code of tuning method
mmc: mediatek: add MT8183 MMC driver support
mmc: mediatek: tune CMD/DATA together
mmc: mediatek: fix cannot receive new request when msdc_cmd_is_ready fail
mmc: mediatek: fill the actual clock for mmc debugfs
mmc: dt-bindings: add support for MT8183 SoC
mmc: uniphier-sd: avoid using broken DMA RX channel
mmc: uniphier-sd: fix DMA disabling
mmc: tmio: simplify the DMA mode test
mmc: tmio: remove TMIO_MMC_HAVE_HIGH_REG flag
mmc: tmio: move MFD variant reset to a platform hook
mmc: renesas_sdhi: Add r8a77470 SDHI1 support
dt-bindings: mmc: renesas_sdhi: Add r8a77470 support
mmc: mmci: add stm32 sdmmc variant
dt-bindings: mmci: add stm32 sdmmc variant
mmc: mmci: add stm32 sdmmc registers
mmc: mmci: add clock divider for stm32 sdmmc
mmc: mmci: add optional reset property
dt-bindings: mmci: add optional reset property
mmc: mmci: add variant property to not read datacnt
...
-----BEGIN PGP SIGNATURE-----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=LRTT
-----END PGP SIGNATURE-----
Merge tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"This is the main pull request for block changes for 4.20. This
contains:
- Series enabling runtime PM for blk-mq (Bart).
- Two pull requests from Christoph for NVMe, with items such as;
- Better AEN tracking
- Multipath improvements
- RDMA fixes
- Rework of FC for target removal
- Fixes for issues identified by static checkers
- Fabric cleanups, as prep for TCP transport
- Various cleanups and bug fixes
- Block merging cleanups (Christoph)
- Conversion of drivers to generic DMA mapping API (Christoph)
- Series fixing ref count issues with blkcg (Dennis)
- Series improving BFQ heuristics (Paolo, et al)
- Series improving heuristics for the Kyber IO scheduler (Omar)
- Removal of dangerous bio_rewind_iter() API (Ming)
- Apply single queue IPI redirection logic to blk-mq (Ming)
- Set of fixes and improvements for bcache (Coly et al)
- Series closing a hotplug race with sysfs group attributes (Hannes)
- Set of patches for lightnvm:
- pblk trace support (Hans)
- SPDX license header update (Javier)
- Tons of refactoring patches to cleanly abstract the 1.2 and 2.0
specs behind a common core interface. (Javier, Matias)
- Enable pblk to use a common interface to retrieve chunk metadata
(Matias)
- Bug fixes (Various)
- Set of fixes and updates to the blk IO latency target (Josef)
- blk-mq queue number updates fixes (Jianchao)
- Convert a bunch of drivers from the old legacy IO interface to
blk-mq. This will conclude with the removal of the legacy IO
interface itself in 4.21, with the rest of the drivers (me, Omar)
- Removal of the DAC960 driver. The SCSI tree will introduce two
replacement drivers for this (Hannes)"
* tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block: (204 commits)
block: setup bounce bio_sets properly
blkcg: reassociate bios when make_request() is called recursively
blkcg: fix edge case for blk_get_rl() under memory pressure
nvme-fabrics: move controller options matching to fabrics
nvme-rdma: always have a valid trsvcid
mtip32xx: fully switch to the generic DMA API
rsxx: switch to the generic DMA API
umem: switch to the generic DMA API
sx8: switch to the generic DMA API
sx8: remove dead IF_64BIT_DMA_IS_POSSIBLE code
skd: switch to the generic DMA API
ubd: remove use of blk_rq_map_sg
nvme-pci: remove duplicate check
drivers/block: Remove DAC960 driver
nvme-pci: fix hot removal during error handling
nvmet-fcloop: suppress a compiler warning
nvme-core: make implicit seed truncation explicit
nvmet-fc: fix kernel-doc headers
nvme-fc: rework the request initialization code
nvme-fc: introduce struct nvme_fcp_op_w_sgl
...
Commit b9762bebc6 ("gpiolib: Pass bitmaps, not integer arrays, to
get/set array") changed the way GPIO values are passed to
gpiod_get/set_array_value() and friends. The new code introduced into
mmc_pwrseq_simple_set_gpios_value() incorrectly interpretes the 'value'
argument as a bitmap of GPIO values and assigns it directly to the
'values' bitmap variable passed to gpiod_set_array_value_cansleep()
instead of filling that bitmap with bits equal to the 'value' argument.
As a result, only member 0 of the array is handled correctly.
Moreover, wrong assumption is taken about the 'values' bitmap size not
exceding the number of bits of the 'value' argument type.
Fix it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the tuning code is becoming more and more bloated, let's make the
set cmd/data delay to inline function to avoid too much redundant code.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MT8183 puts the tune register at top layer, so need add new code
to support it.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for MSDC IP which supports both data tune and async fifo, it can
tune cmd/data together. which can save the time and make the tune
result of CMD more stable as data line are 4bit or 8bit.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when msdc_cmd_is_ready return fail, the req_timeout work has not been
inited and cancel_delayed_work() will return false, then, the request
return directly and never call mmc_request_done().
so need call mod_delayed_work() before msdc_cmd_is_ready()
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
as the mmc core layer has the mmc->actual_clock, so fill it
and drop msdc_host->sclk.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->chan_rx is NULL when UNIPHIER_SD_CAP_BROKEN_DMA_RX quirk flag
is set. In this case, it should not set up DMA.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Once DMA is enabled, it is not possible to disable it because
uniphier_sd_dma_endisable() always sets the DMA_ENABLE_DMASDRW bit
regardless of the argument 'enable'. It should disable DMA when
'enable' is false.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->chan_{rx,tx} represents the DMA capability of the platform.
Even if DMA is supported, there are cases where we want to use PIO,
for example, data length is short enough as commit 5f52c35529
("mmc: tmio: use PIO for short transfers") mentioned.
Regarding the hardware control flow, we are interested in whether DMA
is currently enabled or not, instead of whether the platform has the
DMA capability.
Hence, the several conditionals in tmio_mmc_core.c end up with
checking host->chan_{rx,tx} and !host->force_pio. This is not nice.
Let's flip the flag host->force_pio into host->dma_on.
host->dma_on represents whether the DMA is currently enabled or not.
This flag is set false in the beginning of each command, then should
be set true by tmio_mmc_start_dma() when the DMA is turned on.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TMIO_MMC_HAVE_HIGH_REG is confusing due to its counter-intuitive name.
All the TMIO MMC variants (TMIO MMC, Renesas SDHI, UniPhier SD) actually
have high registers. It is just that each of them implements its own
registers there. The original IP from Panasonic only defines registers
0x00-0xff in the bus_shift=1 review. The register area above them is
platform-dependent.
In fact, TMIO_MMC_HAVE_HIGH_REG is set only by tmio-mmc.c and used to
test the accessibility of CTL_SDIO_REGS. Because it is specific to
the TMIO MFD variant, the right thing to do is to move such registers
to tmio_mmc.c and delete the TMIO_MMC_HAVE_HIGH_REG flag.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CTL_RESET_SDIO register is specific to the TMIO MFD (tmio_mmc.c).
Add a new hook host->reset() for performing a platform-specific
reset sequence, and move CTL_RESET_SDIO over there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The RZ/G1C (a.k.a. R8A77470) comes with three SDHI interfaces,
SDHI0 and SDHI2 are compatible with the R-Car Gen2 SDHIs, SDHI1
is compatible with R-Car Gen3 SDHIs and it can be used as
eMMC as well. This patch adds driver compatibility, and makes
sure both drivers get compiled for the R8A77470.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some SD cards over SPI, reading with the multiblock read command the last
sector will leave the card in a bad state.
Remove last sectors from the multiblock reading cmd.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a stm32 sdmmc variant, rev 1.1.
Introduces a new Manufacturer id "0x53, ascii 'S' to define
new stm32 sdmmc family with clean range of amba
revision/configurations bits (corresponding to sdmmc_ver
register with major/minor fields).
Add 2 variants properties:
-dma_lli, to enable link list support.
-stm32_idmabsize_mask, defines the range of SDMMC_IDMABSIZER register
which specify the number bytes per buffer.
DT properties for sdmmc:
-Indicate signal directions (only one property
for d0dir, d123dir, cmd_dir)
-Select command and data phase relation.
-Select "clock in" from an external driver.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STM32 sdmmc variant has a different clock divider.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a optional reset management.
STM32 sdmmc variant needs to reset hardware block
during the power cycle procedure (for re-initialization).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a boolean property to not read datacnt register.
Needed to support the STM32 sdmmc variant. MMCIDATACNT
register should be read only after the data transfer is completed.
When reading after an error event the read data count value may be
different from the real number of data bytes transferred.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a boolean property to allow to write datactrl
before to send command, whatever the command type (read or write).
Needed to support the STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to define specific pio mask for variants.
Needed to support the STM32 sdmmc variant which has some bits
with different meaning (bits: 21,20,13,12,9)
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds datactrl variant property to define
dpsm enable bit. Needed to support the STM32 variant
(STM32 has no dpsm enable bit).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds command variant properties to define
cpsm enable bit and responses.
Needed to support the STM32 variant (shift of cpsm bit,
specific definition of commands response).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All variants don't pretend to have a startbiterr.
-While data error check, if status register return an error
(like MCI_DATACRCFAIL) we must avoid to check MCI_STARTBITERR
(if not desired).
-expand start_err to MCI_IRQENABLE to avoid to set this bit by default.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to define a datactrl block size
by variant, requested by STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds set_clkreg and set_pwrreg callbacks
at mmci_host_ops to allow to call specific variant.
extends visibility of mmci_write_clk/pwrreg functions
to be used into specific file variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds validate_data callback at mmci_host_ops
to check specific constraints of variant.
Move mmci_validate_data function to regroup mmci_host_ops interfaces.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_error callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
