As explained in the comment introduced above the fix, the Arasan
controller driver starts an operation when the prog register is being
written with a "type" specific to the action to perform.
The prog type used until now to perform a CHANGE READ COLUMN with an SDR
interface was the PAGE READ type (CMD + ADDR + CMD +
DATA). Unfortunately, for an unknown reason (let's call this a silicon
bug) any CHANGE READ COLUMN performed this way in NV-DDR mode will fail:
the data ready flag will never be triggered, nor will be the transfer
complete flag. Forcefully, this leads to a timeout situation which is
not easy to handle.
Fortunately, it was spotted that sending the same commands through a
different prog register "type", CHANGE READ COLUMN ENHANCED, would work
all the time (even though this particular command is not supported by
the core and is only available in a limited set of devices - we only
care about the controller configuration and not the actual command which
is sent to the device). So let's use this type instead when a CHANGE
READ COLUMN is requested.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-22-miquel.raynal@bootlin.com
Now that the necessary peaces to support the NV-DDR interface type have
been contributed, let's add the relevant logic to make use of it. In
particular, the core does not choose the best SDR timings anymore but
calls a more generic helper instead.
This helper checks if NV-DDR is supported by trying to find the best
NV-DDR supported mode through a logic very close to what is being done
for SDR timings. If no NV-DDR mode in common between the NAND controller
and the NAND chip is found, the core will fallback to SDR.
Side note: theoretically, the data clock speed in NV-DDR mode 0 is
slower than in SDR mode 5. In the situation where we would get a working
NV-DDR mode 0, we could also try if SDR mode 5 is supported and
eventually fallback to it in order to get the fastest possible
throughput. However, in the field, it looks like most of the devices
supporting NV-DDR avoid implementing the fastest SDR modes (like 4 and 5
EDO modes, which are a bit more complicated to handle than the other SDR
modes). So, we will stick to the simplest logic: try NV-DDR otherwise
fallback to SDR. If someone else experiences strong differences because
of that we may still implement the logic defined above.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-19-miquel.raynal@bootlin.com
Until now the parameter of the ADDR_TIMING_MODE feature was just the
ONFI timing mode (from 0 to 5) because we were only supporting the SDR
data interface. In the same byte, bits 4 and 5 indicate which data
interface is being configured so use them to set the right mode and also
read them back to ensure the right timing has been setup on the chip's
side.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-17-miquel.raynal@bootlin.com
Introduce a similar helper to onfi_find_closest_sdr_mode(), but for
NV-DDR timings. It just takes a timing structure as parameter and
returns the closest mode by comparing all minimum timings. This is
useful for rigid controllers on which tuning the timings is not
possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-16-miquel.raynal@bootlin.com
As explained in chapter "NV-DDR / NV-DDR2 / NV-DDR3 and Repeat Bytes" of
the ONFI specification, with some commands (mainly the commands which do
not transfer actual data) the data bytes are repeated twice and it is
the responsibility of the receiver to discard them properly. The
concerned commands are: SET_FEATURES, READ_ID, GET_FEATURES,
READ_STATUS, READ_STATUS_ENHANCED, ODT_CONFIGURE. Hence, in the NAND
core we are only impacted by the implementation of READ_ID, GET_FEATURES
and READ_STATUS.
The logic is the same for all:
2/ Check if it is relevant to read all data bytes twice.
1/ Allocate a buffer with twice the requested size (may be done
statically).
2/ Update the instruction structure to read these extra bytes in the
allocated buffer.
3/ Copy the even bytes into the original buffer. The performance hit is
negligible on such small data transfers anyway and we don't really
care about performances at this stage anyway.
4/ Free the allocated buffer, if any.
Note: nand_data_read_op() is also impacted because it is theoretically
possible to run the command/address cycles first, and, as another
operation, do the data transfers. In this case we can easily identify
the impacted commands because the force_8bit flag will be set (due to
the same reason: their data does not go through the same pipeline).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-15-miquel.raynal@bootlin.com
Most timings related to the bus timings are different between SDR and
NV-DDR. However, we identified 9 individual timings which are more
related to the NAND chip internals. These are common between the two
interface types. Fortunately, only these common timings are being shared
through the NAND core and its ->exec_op() interface, which allows the
writing of a simple macro checking the interface type and depending on
it, returning either the relevant SDR timing or the NV-DDR timing. This
is the purpose of the NAND_COMMON_TIMING_PS() macro.
As all this is evaluated at build time, one will immediately be notified
in case a non common timing is being accessed through this macro.
Two handy macros are also inserted at the same time, which use
PSEC_TO_NSEC or PSEC_TO_MSEC so that it is very easy to return timings
in milli-, nano- or pico-seconds, as usually requested by the internal
API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-14-miquel.raynal@bootlin.com
Legacy code should not benefit from newer features, especially in
helpers that have been deprecated for a very long time. People who want
NV-DDR support must migrate their driver to the ->exec_op() API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-13-miquel.raynal@bootlin.com
Same logic as for the SDR path, let's create a
onfi_fill_nvddr_interface_config() helper to fill an interface
configuration structure with NV-DDR timings, given a specific ONFI mode.
There is one additional thing to do compared to SDR mode: tCAD timing
can be fast or slow and this depends on an ONFI parameter page bit. By
default the slow value is declared in the timings structure definition,
but this helper can shrink it down if necessary.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-12-miquel.raynal@bootlin.com
This helper actually fills the interface configuration with SDR data.
As part of the work to bring NV-DDR support, let's rename this helper
onfi_fill_sdr_interface_config() and add a generic indirection to it.
There are no functional changes here, but this will simplify a next
change which adds onfi_fill_nvddr_interface_config() support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-11-miquel.raynal@bootlin.com
When parsing the ONFI parameter page, save the available NV-DDR timing
modes in the core's dynamic ONFI structure. Once available to the rest
of the core out of the ONFI driver, these values will then be used to
derive the best timing mode.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-10-miquel.raynal@bootlin.com
In particular, first ONFI specifications referred to SDR modes as
asynchronous modes, which is not the term we usually have in mind. The
spec has then been updated, so do the same here in the NAND subsystem to
avoid any possible confusion.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-7-miquel.raynal@bootlin.com
In the unlikely event that both blocks 10 and 11 are marked as bad (on a
32 bit machine), then the process of marking block 10 as bad stomps on
cached entry for block 11. There are (of course) other examples.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
[<miquel.raynal@bootlin.com>: Fixed the title]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/774a92693f311e7de01e5935e720a179fb1b2468.1616635406.git.ytc-mb-yfuruyama7@kioxia.com
Commit 82bfd11f1b ("mtd: rawnand: qcom: Add support for Qcom SMEM
parser") made qcomsmem the only parser for qcom_nandc partitions. This
might be problematic for systems with both SPI and NAND MTD devices.
When booting from SPI flash the partition table should not apply to the
NAND flash.
Prepend cmdlinepart and ofpart parsers to allow override of the
partition parser.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/cf470f05af514acd5bd94548804ffa96b966a0a8.1619029869.git.baruch@tkos.co.il
Smatch complains that the error code is not set on this error path:
drivers/mtd/nand/raw/nand_base.c:842 nand_setup_interface()
warn: missing error code 'ret'
But actually returning success is intentional because the NAND chip will
still work in mode 0. This patch adds a "ret = 0;" assignment to make
the intent more clear and to silence the static checker warning. It
doesn't affect the compiled code because GCC optimises the assignment
away.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YH6Ugwz3gcga+q8X@mwanda
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210408111514.1011020-2-yukuai3@huawei.com
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210407100526.3278741-1-liwei391@huawei.com
JFFS2:
- Use splice_write()
- Fix for a slab-out-of-bounds bug
UBI:
- Fix for clang related warnings
- Code cleanup
UBIFS:
- Fix for inode rebirth at replay
- Set s_uuid
- Use zstd for default filesystem
-----BEGIN PGP SIGNATURE-----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=IwH7
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Use splice_write()
- Fix for a slab-out-of-bounds bug
UBI:
- Fix for clang related warnings
- Code cleanup
UBIFS:
- Fix for inode rebirth at replay
- Set s_uuid
- Use zstd for default filesystem"
* tag 'for-linus-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: Remove unnecessary struct declaration
jffs2: Hook up splice_write callback
jffs2: avoid Wempty-body warnings
jffs2: Fix kasan slab-out-of-bounds problem
ubi: Fix fall-through warnings for Clang
ubifs: Report max LEB count at mount time
ubifs: Set s_uuid in super block to support ima/evm uuid options
ubifs: Default to zstd compression
ubifs: Only check replay with inode type to judge if inode linked
-----BEGIN PGP SIGNATURE-----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=ovSn
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Stop synchronizing kernel log buffer readers by logbuf_lock. As a
result, the access to the buffer is fully lockless now.
Note that printk() itself still uses locks because it tries to flush
the messages to the console immediately. Also the per-CPU temporary
buffers are still there because they prevent infinite recursion and
serialize backtraces from NMI. All this is going to change in the
future.
- kmsg_dump API rework and cleanup as a side effect of the logbuf_lock
removal.
- Make bstr_printf() aware that %pf and %pF formats could deference the
given pointer.
- Show also page flags by %pGp format.
- Clarify the documentation for plain pointer printing.
- Do not show no_hash_pointers warning multiple times.
- Update Senozhatsky email address.
- Some clean up.
* tag 'printk-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (24 commits)
lib/vsprintf.c: remove leftover 'f' and 'F' cases from bstr_printf()
printk: clarify the documentation for plain pointer printing
kernel/printk.c: Fixed mundane typos
printk: rename vprintk_func to vprintk
vsprintf: dump full information of page flags in pGp
mm, slub: don't combine pr_err with INFO
mm, slub: use pGp to print page flags
MAINTAINERS: update Senozhatsky email address
lib/vsprintf: do not show no_hash_pointers message multiple times
printk: console: remove unnecessary safe buffer usage
printk: kmsg_dump: remove _nolock() variants
printk: remove logbuf_lock
printk: introduce a kmsg_dump iterator
printk: kmsg_dumper: remove @active field
printk: add syslog_lock
printk: use atomic64_t for devkmsg_user.seq
printk: use seqcount_latch for clear_seq
printk: introduce CONSOLE_LOG_MAX
printk: consolidate kmsg_dump_get_buffer/syslog_print_all code
printk: refactor kmsg_dump_get_buffer()
...
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
* Constify buf in mtd_write_user_prot_reg()
* Constify name param in mtd_bdi_init
* Fix fall-through warnings for Clang
* Get rid of Big MTD Lock ouf of mtdchar
* Drop mtd_mutex usage from mtdchar_open()
* Don't lock when recursively deleting partitions
* Use module_mtd_blktrans() to register driver when relevant
* Parse MTD as NVMEM cells
* New OTP (one-time-programmable) erase ioctl
* Require write permissions for locking and badblock ioctls
* physmap:
- Fix error return code of physmap_flash_remove()
- physmap-bt1-rom: Fix unintentional stack access
* ofpart parser:
- Support Linksys Northstar partitions
- Make symbol 'bcm4908_partitions_quirks' static
- Limit parsing of deprecated DT syntax
- Support BCM4908 fixed partitions
* Qcom parser:
- Incompatible with spi-nor 4k sectors
- Fix error condition
- Extend Qcom SMEM parser to SPI flash
CFI:
* Disable broken buffered writes for CFI chips within ID 0x2201
* Address a Coverity report for unused value
SPI NOR core:
* Add OTP support
* Fix module unload while an op in progress
* Add various cleanup patches
* Add Michael and Pratyush as designated reviewers in MAINTAINERS
SPI NOR controller drivers:
* intel-spi:
- Move platform data header to x86 subfolder
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND (APPLIED THEN REVERTED)
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmCBq3UACgkQJWrqGEe9
VoS9Xwf+I9W5WZS+WLYdlJ9RvuPDYVyZolZdsxIOOaOGuMAYSLJI/GjWJyHAFdwJ
qIPvr6qFnmKfUUaFZkln5Qk4QSfx+/t7+yj57e3lM9bSBEfTNToMI4AU8X6UAxa5
NHnsU8O8sohnk2UrP1qRtk3IezJ0FdzHbQAc82GQ1QY+IE0NwHg0ETjgESR5iEfq
PSnXb5Dgd637ENUlLsauSLbqFcD8sULvA3fJngxkQbBXDfv3KNZQhNsqw/l7NMY5
rROk8/jv7kgnYs8ObdkWO9SZ9QIiFSLk3vgbrTTNl8ozYpIMVbsrLmsnh7G34RNO
oWmbyOQdMDugaPYLJ9aTQmyI1qbKsA==
=zJPs
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core:
- Handle possible -EPROBE_DEFER from parse_mtd_partitions()
- Constify buf in mtd_write_user_prot_reg()
- Constify name param in mtd_bdi_init
- Fix fall-through warnings for Clang
- Get rid of Big MTD Lock ouf of mtdchar
- Drop mtd_mutex usage from mtdchar_open()
- Don't lock when recursively deleting partitions
- Use module_mtd_blktrans() to register driver when relevant
- Parse MTD as NVMEM cells
- New OTP (one-time-programmable) erase ioctl
- Require write permissions for locking and badblock ioctls
- physmap:
- Fix error return code of physmap_flash_remove()
- physmap-bt1-rom: Fix unintentional stack access
- ofpart parser:
- Support Linksys Northstar partitions
- Make symbol 'bcm4908_partitions_quirks' static
- Limit parsing of deprecated DT syntax
- Support BCM4908 fixed partitions
- Qcom parser:
- Incompatible with spi-nor 4k sectors
- Fix error condition
- Extend Qcom SMEM parser to SPI flash
CFI:
- Disable broken buffered writes for CFI chips within ID 0x2201
- Address a Coverity report for unused value
SPI NOR core:
- Add OTP support
- Fix module unload while an op in progress
- Add various cleanup patches
- Add Michael and Pratyush as designated reviewers in MAINTAINERS
SPI NOR controller drivers:
- intel-spi:
- Move platform data header to x86 subfolder
NAND core:
- Fix error handling in nand_prog_page_op() (x2)
- Add a helper to retrieve the number of ECC bytes per step
- Add a helper to retrieve the number of ECC steps
- Let ECC engines advertize the exact number of steps
- ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
- ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
- Add support for secure regions in NAND memory
- Try not to use the ECC private structures
- Remove duplicate include in rawnand.h
- BBT:
- Skip bad blocks when searching for the BBT in NAND (APPLIED THEN REVERTED)
Raw NAND controller drivers:
- Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
- GPMI:
- Fix a double free in gpmi_nand_init
- Rockchip:
- Use flexible-array member instead of zero-length array
- Atmel:
- Update ecc_stats.corrected counter
- MXC:
- Remove unneeded of_match_ptr()
- R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
- Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
- FSMC:
- Fix error code in fsmc_nand_probe()
- OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
- Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
- gigadevice: Support GD5F1GQ5UExxG"
* tag 'mtd/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (89 commits)
Revert "mtd: rawnand: bbt: Skip bad blocks when searching for the BBT in NAND"
mtd: core: Constify buf in mtd_write_user_prot_reg()
Revert "mtd: spi-nor: macronix: Add support for mx25l51245g"
mtd: spi-nor: core: Fix an issue of releasing resources during read/write
mtd: cfi_cmdset_0002: remove redundant assignment to variable timeo
mtd: cfi_cmdset_0002: Disable buffered writes for AMD chip 0x2201
mtd: rawnand: qcom: Use dma_mapping_error() for error check
mtd: rawnand: gpmi: Fix a double free in gpmi_nand_init
mtd: rawnand: qcom: Add missing nand_cleanup() in error path
mtd: rawnand: Add support for secure regions in NAND memory
dt-bindings: mtd: Add a property to declare secure regions in NAND chips
dt-bindings: mtd: Convert Qcom NANDc binding to YAML
mtd: spi-nor: winbond: add OTP support to w25q32fw/jw
mtd: spi-nor: implement OTP support for Winbond and similar flashes
mtd: spi-nor: add OTP support
mtd: spi-nor: swp: Improve code around spi_nor_check_lock_status_sr()
mtd: spi-nor: Move Software Write Protection logic out of the core
mtd: rawnand: bbt: Skip bad blocks when searching for the BBT in NAND
include: linux: mtd: Remove duplicate include of nand.h
mtd: parsers: ofpart: support Linksys Northstar partitions
...
This reverts commit bd9c9fe2ad.
Since commit bd9c9fe2ad ("mtd: rawnand: bbt: Skip bad blocks when
searching for the BBT in NAND") the bad block table cannot be found
on a imx27-phytec-phycard-s-rdk board:
Bad block table not found for chip 0
Bad block table not found for chip 0
Revert it for now, until a better solution can be found.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210419140350.809853-1-festevam@gmail.com
The write buffer comes from user and should be const.
Constify write buffer in mtd core and across all _write_user_prot_reg()
users. cfi_cmdset_{0001, 0002} and onenand_base will pay the cost of an
explicit cast to discard the const qualifier since the beginning, since
they are using an otp_op_t function prototype that is used for both reads
and writes. mtd_dataflash and SPI NOR will benefit of the const buffer
because they are using different paths for writes and reads.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060931.7119-1-tudor.ambarus@microchip.com
struct ubi_wl_entry is defined at 178th line.
The declaration here is unnecessary. Remove it.
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmB1XbkACgkQJWrqGEe9
VoSWEAf6Al9DFds3w32oS8OB19pMb66jWLPvt//gIwV4tzSIsauQLqo4uBqDUPSt
EdUyehN6W792qsekmOReRc4ZcS2HpNPT5PRwYtsxPMkVmEL56tqs5ObNPGNOwvoH
9vyvsx7EhSu10a9JHjgJeNMVOBDMA8quXqHw0Y3cL2UBpuCYMm37ANF8okdvOmmr
Ykg1nCbfZL/dxFCGZ15ZuYuGQXea8PUryyxXUsWLDvsHg4KuhQKKtkarXmzz6XiD
tAyShtSrJFo/T0FniWc8jFbaq8WkU7XBg5f5qTTt5uT4JoXWGmjbIbXG0My91RKY
RO0b6z/odPOW1UHarlK8HrKW22YF9A==
=+fKJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
MTD core:
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
- Add OTP support
- Fix module unload while an op in progress
- Add various cleanup patches
SPI NOR controller drivers changes:
- intel-spi: Move platform data header to x86 subfolder
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmByqyYACgkQS1VPR6WN
FOkkYwgAvjQoUPZ/ZzwKbAuEseVB4DWj0goyTNNjksw5oIDmxcfDDd4gFTyRvLmb
eyYMGCqnBSq9asbmzWu6H5IYWllsWgRvHuRlfKlJPj6Iqc+kAv8zaezQcY5t9lYy
EopogLmc3RJdHdV3FbiRYqebATCCfwkQzDJdp7QU3EdKzQp+6AmJdClssKsxkXsm
mUHmrhRF7K4jloaKfsbDwvM7DHPyhJEP/AyuDRactZzoQLhrTB/5rJ3nwpQ3k0x6
EZ53Qx08Qk9lhzR7trYOaltoTtOVc9wiIz+QGuLXfleBEfi7hRBvscx2FZKL4GwI
O2Fsg4of06KKTJ3LiOuiHykXFZ+GUA==
=/6EZ
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- Add OTP support
- Fix module unload while an op in progress
- Add various cleanup patches
SPI NOR controller drivers changes:
- intel-spi: Move platform data header to x86 subfolder
Just a couple of fixes for v5.13-rc1
* Disable broken buffered writes for CFI chips within ID 0x2201
* Address a Coverity report for unused value
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAmB10GgQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW40OcCADGpa4hnu3vWIkgwHGOFhW6YtsDTZ5A8LSw
T0eSdEets7No8p1E0HjOb623qcqm7WMfgYBkRFHLqbcl/BYZ4IUQscBh+5iP28Lf
i+AJdnxdryYZLNIiympwhSbvg9zRkGY6Abi2OVdPeEBNlb89Fo4fst5dnsc4CK8T
evQlA7P5ZeQk4DSHPGN6BfvZrej7nVczdmB1srpt9pxKWdwWGmEQoj+d1zOcYe0j
ziTcSBNbkGqLZ0agtCZiE2tzFOLGcsnMc2fXk7DYdu3CL5EBu5gP+QTdk+Iftdsb
G6VvOYaLF3AsqkacbSjxdwsoyUNVSIsqO4BM0YCxS0EsphDU4qkX
=LX/U
-----END PGP SIGNATURE-----
Merge tag 'cfi/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
CFI changes
Just a couple of fixes for v5.13-rc1
* Disable broken buffered writes for CFI chips within ID 0x2201
* Address a Coverity report for unused value
This reverts commit 04b8edad26.
mx25l51245g and mx66l51235l have the same flash ID. The flash
detection returns the first entry in the flash_info array that
matches the flash ID that was read, thus for the 0xc2201a ID,
mx25l51245g was always hit, introducing a regression for
mx66l51235l.
If one wants to differentiate the flash names, a better fix would be
to differentiate between the two at run-time, depending on SFDP,
and choose the correct name from a list of flash names, depending on
the SFDP differentiator.
Fixes: 04b8edad26 ("mtd: spi-nor: macronix: Add support for mx25l51245g")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210402082031.19055-2-tudor.ambarus@microchip.com
If rmmod the driver during read or write, the driver will release the
resources which are used during read or write, so it is possible to
refer to NULL pointer.
Use the testcase "mtd_debug read /dev/mtd0 0xc00000 0x400000 dest_file &
sleep 0.5;rmmod spi_hisi_sfc_v3xx.ko", the issue can be reproduced in
hisi_sfc_v3xx driver.
To avoid the issue, fill the interface _get_device and _put_device of
mtd_info to grab the reference to the spi controller driver module, so
the request of rmmod the driver is rejected before read/write is finished.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1617262486-4223-1-git-send-email-yangyicong@hisilicon.com
The variable timeo is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210325174514.486272-1-colin.king@canonical.com
Addresses-Coverity: ("Unused value")
Buffer writes do not work with AMD chip 0x2201. The chip in question
is a AMD/Spansion/Cypress Semiconductor S29GL256N and datasheet [1]
talks about writing buffers being possible. While waiting for a neater
solution resort to writing word-sized chunks only.
Without the patch kernel logs will be flooded with entries like below:
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device...
done.
jffs2_build_filesystem(): erasing all blocks after the end marker...
MTD do_write_buffer_wait(): software timeout, address:0x01ec000a.
jffs2: Write clean marker to block at 0x01920000 failed: -5
MTD do_write_buffer_wait(): software timeout, address:0x01e2000a.
jffs2: Write clean marker to block at 0x01880000 failed: -5
MTD do_write_buffer_wait(): software timeout, address:0x01e0000a.
jffs2: Write clean marker to block at 0x01860000 failed: -5
MTD do_write_buffer_wait(): software timeout, address:0x01dc000a.
jffs2: Write clean marker to block at 0x01820000 failed: -5
MTD do_write_buffer_wait(): software timeout, address:0x01da000a.
jffs2: Write clean marker to block at 0x01800000 failed: -5
...
Tested on a Buffalo wzr-hp-g300nh running kernel 5.10.16.
[1] https://www.cypress.com/file/219941/download
or https://datasheetspdf.com/pdf-file/565708/SPANSION/S29GL256N/1
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210309174859.362060-1-sandberg@mailfence.com
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
Fixes: 4d02423e9a ("mtd: nand: gpmi: Fix gpmi_nand_init() error path")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060905.5251-1-lyl2019@mail.ustc.edu.cn
On a typical end product, a vendor may choose to secure some regions in
the NAND memory which are supposed to stay intact between FW upgrades.
The access to those regions will be blocked by a secure element like
Trustzone. So the normal world software like Linux kernel should not
touch these regions (including reading).
The regions are declared using a NAND chip DT property,
"secure-regions". So let's make use of this property in the raw NAND
core and skip access to the secure regions present in a system.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-4-manivannan.sadhasivam@linaro.org
With all the helper functions in place, add OTP support for the Winbond
W25Q32JW and W25Q32FW.
Both were tested on a LS1028A SoC with a NXP FSPI controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-4-michael@walle.cc
Use the new OTP ops to implement OTP access on Winbond flashes. Most
Winbond flashes provides up to four different OTP regions ("Security
Registers").
Winbond devices use a special opcode to read and write to the OTP
regions, just like the RDSFDP opcode. In fact, it seems that the
(undocumented) first OTP area of the newer flashes is the actual SFDP
table.
On a side note, Winbond devices also allow erasing the OTP regions as
long as the area isn't locked down.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-3-michael@walle.cc
SPI flashes sometimes have a special OTP area, which can (and is) used to
store immutable properties like board serial number or vendor assigned
network hardware addresses.
The MTD subsystem already supports accessing such areas and some (non
SPI NOR) flashes already implement support for it. It differentiates
between user and factory areas. User areas can be written by the user and
factory ones are pre-programmed and locked down by the vendor, usually
containing an "electrical serial number". This patch will only add support
for the user areas.
Lay the foundation and implement the MTD callbacks for the SPI NOR and add
necessary parameters to the flash_info structure. If a flash supports OTP
it can be added by the convenience macro OTP_INFO(). Sometimes there are
individual regions, which might have individual offsets. Therefore, it is
possible to specify the starting address of the first regions as well as
the distance between two regions (e.g. Winbond devices uses this method).
Additionally, the regions might be locked down. Once locked, no further
write access is possible.
For SPI NOR flashes the OTP area is accessed like the normal memory, e.g.
by offset addressing; except that you either have to use special read/write
commands (Winbond) or you have to enter (and exit) a specific OTP mode
(Macronix, Micron).
Thus we introduce four operations to which the MTD callbacks will be
mapped: .read(), .write(), .lock() and .is_locked(). The read and the write
ops will be given an address offset to operate on while the locking ops use
regions because locking always affects a whole region. It is up to the
flash driver to implement these ops.
Signed-off-by: Michael Walle <michael@walle.cc>
[ta: use div64_u64(), IS_ALIGNED, params->otp.org. unsigned int region,
drop comment, add rlen local variable in spi_nor_mtd_otp_lock()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-2-michael@walle.cc
It makes the core file a bit smaller and provides better separation
between the Software Write Protection features and the core logic.
All the next generic software write protection features (e.g. Individual
Block Protection) will reside in swp.c.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210322075131.45093-2-tudor.ambarus@microchip.com
The blocks containing the bad block table can become bad as well. So
make sure to skip any blocks that are marked bad when searching for the
bad block table.
Otherwise in very rare cases where two BBT blocks wear out it might
happen that an obsolete BBT is used instead of a newer available
version.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210325102337.481172-1-s.riedmueller@phytec.de
This allows extending ofpart parser with support for Linksys Northstar
devices. That support uses recently added quirks mechanism.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210312134919.7767-2-zajec5@gmail.com
Partitions that contains the nvmem-cells compatible will register
their direct subonodes as nvmem cells and the node will be treated as a
nvmem provider.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210312062830.20548-1-ansuelsmth@gmail.com
This may sound like a contradiction but some SPI-NOR flashes really
support erasing their OTP region until it is finally locked. Having the
possibility to erase an OTP region might come in handy during
development.
The ioctl argument follows the OTPLOCK style.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210303201819.2752-1-michael@walle.cc
