Commit ac75a04104 ("HID: i2c-hid: fix size check and type usage") started
writing messages when the ret_size is <= 2 from i2c_master_recv. However, my
device i2c-DLL07D1 returns 2 for a short period of time (~0.5s) after I stop
moving the pointing stick or touchpad. It varies, but you get ~50 messages
each time which spams the log hard.
[ 95.925055] i2c_hid i2c-DLL07D1:01: i2c_hid_get_input: incomplete report (83/2)
This has also been observed with a i2c-ALP0017.
[ 1781.266353] i2c_hid i2c-ALP0017:00: i2c_hid_get_input: incomplete report (30/2)
Only print the message when ret_size is totally invalid and less than 2 to cut
down on the log spam.
Fixes: ac75a04104 ("HID: i2c-hid: fix size check and type usage")
Reported-by: John Smith <john-s-84@gmx.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Recent kernels support asynchronous probing; most hyperv drivers
can be probed async easily so set the required flag for this.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The touch sensors on the 2nd-gen Intuos tablets don't use a 4096x4096
sensor like other similar tablets (3rd-gen Bamboo, Intuos5, etc.).
The incorrect maximum XY values don't normally affect userspace since
touch input from these devices is typically relative rather than
absolute. It does, however, cause problems when absolute distances
need to be measured, e.g. for gesture recognition. Since the resolution
of the touch sensor on these devices is 10 units / mm (versus 100 for
the pen sensor), the proper maximum values can be calculated by simply
dividing by 10.
Fixes: b5fd2a3e92 ("Input: wacom - add support for three new Intuos devices")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We want to keep device-specific quirks as contained as possible so that the
the code remains maintainable. Our 'wacom_setup_device_quirks' function is
the usual place for this, but some quirks need to be applied to the HID
descriptor as it is parsed. This commit introduces a new function which is
called for each usage so that any HID-specific quirks can be applied. The
function now houses quirks that were being done in 'wacom_feature_mapping'
and 'wacom_usage_mapping'.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Detecting the number of supported touches for a particular device used
to be tricky, both because early forms of the driver didn't have a very
good HID parser and because early hardware didn't always advertise the
actual number. At the time, we added a block of code which would ensure
that touch_max would always be equal to at least 1 on any touch device,
and relied on setting touch_max to e.g. 2 only for the multitouch-capable
exceptions.
The common case has since flipped, and the driver and descriptors can
reliably detect the number of touches supported by modern sensors.
Because of this, it makes sense to remove the fixup code and instead
place static declarations of "touch_max = 1" for these old devices. It
isn't entirely clear if all 2-finger devices actually report a maximum
number of touches so we leave these declarations still in place.
For the eagle-eyed, the "> BAMBOO_PT" condition was originally equivalent
to ">= TABLETPC", which is what the intent was. This commit doesn't have
to consider the types introduced in the interim since they shouldn't be
affected, hence why only the tablet PC definitions have been modified.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If our length is greater than the size of the buffer, we
overflow the buffer
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Rosenberg <drosen@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Detected on the Dell XPS 9365.
The laptop has 2 devices that benefit from the hid-generic auto-unbinding.
When those 2 devices are presented to the userspace, udev loads both wacom and
hid-multitouch. When this happens, the code in __hid_bus_reprobe_drivers() is
called concurrently and the second device gets reprobed twice.
An other bug in the power_supply subsystem prevent to remove the wacom driver
if it just finished its initialization, which basically kills the wacom node.
[jkosina@suse.cz: reformat changelog a bit]
Fixes c17a7476e4 ("HID: core: rewrite the hid-generic automatic unbind")
Cc: stable@vger.kernel.org # v4.17
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds the drums and guitar extensions for Wiimote devices.
Devices are reported as "Nintendo Wii Remote Guitar/Drums". If I ever
get my hands on "RockBand" guitars, I will try to report them via the
same interface so user-space does not have to bother which device it
deals with.
This is a rebase of the original commits 8e22ecb603 and 73f8645db1.
They were reverted several years ago, since they were dependent on the
ABS_* rework of the input core. Sadly, this never worked out so these
commits were never pushed into a release. This rebase now uses the
ABS_HAT* event codes to report all pressure information.
Signed-off-by: Nicolas.Adenis-Lamarre <nicolas.adenis.lamarre@gmail.com>
(Original commits by Nicolas, adapted to v4.18 by David)
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB completion callback does not disable interrupts while acquiring
the ->lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The redragon asura keyboard registers two input devices. The initial commit
85455dd906 ("HID: redragon: Fix modifier keys for Redragon Asura Keyboard")
considered this an error and prevented one of the devices from registering.
However, once this is done the num lock and caps lock leds no longer toggle on
and off, although the key functionality is not affected.
This commit removes the code that prevents the input device
registration and restores the num lock and caps lock LEDs.
Fixes: 85455dd906 ("HID: redragon: Fix modifier keys for Redragon Asura Keyboard")
Signed-off-by: Robert Munteanu <rombert@apache.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When sysfs_create_group fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling sysfs_create_group.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some wacom w9013 devices have a vddl supply for "low valtage"
requirements. Add support in this driver to turn on this low voltage
supply. We can also drop a handful of error messages because the
regulator core is already printing an error when bulk regulators fail to
enable or disable.
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dmitry Torokhov <dtor@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use devm here to save some lines and prepare for bulk regulator usage in
this driver. Otherwise, when we devm bulk get regulators we'll free the
containing i2c_hid structure and try to put regulator pointers from
freed memory.
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dmitry Torokhov <dtor@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- Wacom 2nd-gen Intuos Pro large Y axis handling fix from Jason Gerecke
- fix for hibernation in Intel ISH driver, from Even Xu
- crash fix for hid-steam driver, from Rodrigo Rivas Costa
- new device ID addition to google-hammer driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: Correct logical maximum Y for 2nd-gen Intuos Pro large
HID: intel_ish-hid: ipc: register more pm callbacks to support hibernation
HID: steam: use hid_device.driver_data instead of hid_set_drvdata()
HID: google: Add support for whiskers
The HID descriptor for the 2nd-gen Intuos Pro large (PTH-860) contains
a typo which defines an incorrect logical maximum Y value. This causes
a small portion of the bottom of the tablet to become unusable (both
because the area is below the "bottom" of the tablet and because
'wacom_wac_event' ignores out-of-range values). It also results in a
skewed aspect ratio.
To fix this, we add a quirk to 'wacom_usage_mapping' which overwrites
the data with the correct value.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current ISH driver only registers suspend/resume PM callbacks which don't
support hibernation (suspend to disk). Basically after hiberation, the ISH
can't resume properly and user may not see sensor events (for example: screen
rotation may not work).
User will not see a crash or panic or anything except the following message
in log:
hid-sensor-hub 001F:8086:22D8.0001: timeout waiting for response from ISHTP device
So this patch adds support for S4/hiberbation to ISH by using the
SIMPLE_DEV_PM_OPS() MACRO instead of struct dev_pm_ops directly. The suspend
and resume functions will now be used for both suspend to RAM and hibernation.
If power management is disabled, SIMPLE_DEV_PM_OPS will do nothing, the suspend
and resume related functions won't be used, so mark them as __maybe_unused to
clarify that this is the intended behavior, and remove #ifdefs for power
management.
Cc: stable@vger.kernel.org
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When creating the low-level hidraw device, the reference to steam_device
was stored using hid_set_drvdata(). But this value is not guaranteed to
be kept when set before calling probe. If this pointer is reset, it
crashes when opening the emulated hidraw device.
It looks like hid_set_drvdata() is for users "avobe" this hid_device,
while hid_device.driver_data it for users "below" this one.
In this case, we are creating a virtual hidraw device, so we must use
hid_device.driver_data.
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Tested-by: Mariusz Ceier <mceier+kernel@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The script:
./scripts/documentation-file-ref-check --fix
Gives multiple hints for broken references on some files.
Manually use the one that applies for some files.
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Another device in the hammer class, with USB id 0x5030.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- improvement of duplicate usage handling in hid-input from Benjamin Tissoires
- Win 8.1 precisioun touchpad spec implementation from Benjamin Tissoires
When we receive a RMI4 report, we should not unconditionally send an
input_sync event. Instead, we should let the rmi4 transport layer do it
for us.
This fixes a situation where we might receive X in a report and the rest
in a subsequent one. And this messes up user space.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=100436
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Oscar Morante <spacepluk@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to [1] and also seemingly agreed by [2], the Scan Time usage
(0x0D 0x56) is a report level usage, not a contact level usage.
However, the hid-multitouch driver currently includes HID_DG_SCANTIME
when calculating `td->last_slot_field', which may lead to
mt_complete_slot() being prematurely called in certain cases (e.g. when
each touch input report includes more than one contact and the Scan Time
usage appears before any contact logical collection).
This patch fixes the issue by skipping mt_store_field() on
HID_DG_SCANTIME, similar to how HID_DG_CONTACTCOUNT and
HID_DG_CONTACTMAX are handled.
[1] https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/windows-precision-touchpad-required-hid-top-level-collections#windows-precision-touchpad-input-reports
[2] https://patchwork.kernel.org/patch/1742181/
Fixes: 29cc309d8b ("HID: hid-multitouch: forward MSC_TIMESTAMP")
Signed-off-by: Ben Chan <benchan@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Delcom offers different types of products sharing the same USB VID/PID
as the Visual Signal Indicator. Other products need to be handled by
HID Generic what's not possible currently because USB VID/PID are
listed in hid_have_special_driver[].
After e04a0442d3 ("HID: core: remove the absolute need of
hid_have_special_driver[]") we can now remove the Delcom entry.
If a Visual Signal Indicator device is plugged-in, HID core
will start a reprobe if hid-led driver is available.
If another device with same USB VID/PID is plugged-in, then hid-led
can be blacklisted and HID Generic handles the device.
Thanks to Delcom for providing test devices.
Reported-by: Douglas Lovett <dlovett@delcomproducts.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Using the power supply APIs requires selecting the appropriate
Kconfig symbol, otherwise we get this build failure:
drivers/hid/hid-steam.o: In function `steam_unregister':
hid-steam.c:(.text+0x1cc): undefined reference to `power_supply_unregister'
drivers/hid/hid-steam.o: In function `steam_battery_get_property':
hid-steam.c:(.text+0x2d2): undefined reference to `power_supply_get_drvdata'
drivers/hid/hid-steam.o: In function `steam_raw_event':
hid-steam.c:(.text+0xcba): undefined reference to `power_supply_changed'
drivers/hid/hid-steam.o: In function `steam_register':
hid-steam.c:(.text+0x13e3): undefined reference to `power_supply_register'
hid-steam.c:(.text+0x13fe): undefined reference to `power_supply_powers'
Fixes: f827197907 ("HID: steam: add battery device.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since commit 85ae911331 ("HID: i2c-hid: remove custom locking from
i2c_hid_open/close") there are no more users of i2c_hid_open_mut.
Remove the unused mutex.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 1st-generation Intuos tablets (CTL-X80) include an "in range" flag
like some professional tablets. To ensure the pen remains usable at as
large as distance as possible (and to preemptively disable touch when
it is nearby) we need to ensure that we handle these "in range" events.
Handling of tool type identification has been moved to occur only when
the pen is fully in prox rather than any time the "stylus_in_proximity"
flag changes (which is controlled by the further-out "in range" flag).
Link: https://sourceforge.net/p/linuxwacom/bugs/358/
Link: https://github.com/linuxwacom/xf86-input-wacom/issues/14
Link: https://github.com/linuxwacom/xf86-input-wacom/issues/17
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix comment typo for hid_hw_open().
[jkosina@suse.cz: write at least some changelog]
Signed-off-by: Hisao Tanabe <xtanabe@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a mapping for Push-To-Talk joystick trigger button.
Tested on ChromeBox/ChromeBook with various Plantronics devices.
Signed-off-by: Terry Junge <terry.junge@plantronics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some exit paths from mt_need_to_apply_feature() returned int instead
of bool; fix that up.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On many Chromebooks touch devices are multi-sourced; the components are
electrically compatible and one can be freely swapped for another without
changing the OS image or firmware.
To avoid bunch of scary messages when device is not actually present in the
system let's try testing basic communication with it and if there is no
response terminate probe early with -ENXIO.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
->product, ->version and ->type fields in the client struct were left out
unitialized from the hid device fields; fix that.
Reported-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are two ways to connect the Steam Controller: directly to the USB
or with the USB wireless adapter. Both methods are similar, but the
wireless adapter can connect up to 4 devices at the same time.
The wired device will appear as 3 interfaces: a virtual mouse, a virtual
keyboard and a custom HID device.
The wireless device will appear as 5 interfaces: a virtual keyboard and
4 custom HID devices, that will remain silent until a device is actually
connected.
The custom HID device has a report descriptor with all vendor specific
usages, so the hid-generic is not very useful. In a PC/SteamBox Valve
Steam Client provices a software translation by using hidraw and a
creates a uinput virtual gamepad and XTest keyboard/mouse.
This driver intercepts the hidraw usage, so it can get out of the way
when the Steam Client is in use.
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 0457:10fb touchscreen found on the Toshiba Click Mini L9W-B needs
to have a report-decriptors command send to it on resume in order for
the touchscreen to start generating events again on resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Never directly free @dev after calling device_register(), even
if it returned an error. Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If only the first 't4_read_write_register()' call fails, the error code
will be overwritten and lost.
Directly report the error instead.
While at it, log some errors if 't4_read_write_register()' fails, as done
in the rest of the driver.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
if 'read_flag' is false, there is no need to allocate and free memory.
We can simply avoid the memory allocation and pass NULL to kfree.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If the data received is not what is expected, we should return an error.
Otherwise, we return 0 or a positive value which will be interpreted as
success, but '*read_val' has not been updated.
Fixes: 73196ebe13 ("HID: alps: add support for Alps T4 Touchpad device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Win8 spec also declare other features we want to support:
latency and surface and button switches.
Though it doesn't seem we need to activate those by default, we have been
proved in the past that manufacturers rely on the Windows driver behavior
so we better mimic it to prevent further issues.
The current way of setting the features is cumbersome. It avoids iterating
over the list of features, but the way we store/retrieve the data just
doesn't scale with more than two values.
So iterate over the features when we decide to switch on the device and
make it simpler to extend.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We now have HID_QUIRK_INPUT_PER_APPLICATION that splits the devices
into several devices. This helps us as we can now rely on hid-input
to set the names for us.
Also, this helps removing some magical numbers '0' when calling
.input_configured().
The only thing to take care of is that the field .report in struct
hid_input is now null. We need to iterate over the full list of
reports attached to a hid_input.
This is required for some Advanced Silicon touchscreen to correctly apply
the HID_QUIRK_INPUT_PER_APPLICATION as they have 2 reports associated
with the hidinput node. One contains the Input data, the other one
contains the Output data.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Given that we create one input node per application, we should name
the input node accordingly to not lose userspace.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is not a good idea to try to fit all types of applications in the
same input report. There are a lot of devices that are needing
the quirk HID_MULTI_INPUT but this quirk doesn't match the actual HID
description as it is based on the report ID.
Given that most devices with MULTI_INPUT I can think of split nicely
the devices inputs into application, it is a good thing to split the
devices by default based on this assumption.
Also make hid-multitouch following this rule, to not have to deal
with too many input created.
While we are at it, fix some checkpatch complaints about converting
'unsigned' to 'unsigned int'.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We were only storing the report in case of QUIRK_MULTI_INPUT.
It is interesting for the upcoming HID_QUIRK_INPUT_PER_APP to also
store the full list of reports that are attached to it.
We need the full list because a device (Advanced Silicon has some)
might want to use a different report ID for the Input reports and
the Output reports. Storing the full list allows the drivers to
have all the data.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_ishtp_get_report() may be called by multiple callers at the same
time, causing trouble with the static local buffer used.
Also there is no reason to use a non stack buffer, the buffer is tiny
and ishtp_cl_send() copies its contents so the lifetime is not an
issue either.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With the headersize check outside of the loop, the second time through
the loop the: "payload_len = recv_msg->hdr.size;" statement may deref
recv_msg while it is pointing outside of our input buffer.
Move the headersize check to inside the loop to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The IBM/Lenovo Scrollpoint mice feature a trackpoint-like stick instead of a
scrolling wheel capable of 2-D (vertical+horizontal) scrolling. hid-generic
does only expose 1-D (vertical) scrolling functionality for these mice. This
patch adds support for horizontal scrolling for the IBM/Lenovo Scrollpoint mice
to hid-lenovo.
[jkosina@suse.cz: remove change versioning from git changelog]
Signed-off-by: Peter Ganzhorn <peter.ganzhorn@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter De Wachter <pdewacht@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
i2c_hid_command() returns non-zero in error cases (the actual
errno). Error handling in for I2C_HID_QUIRK_RESEND_REPORT_DESCR
case in i2c_hid_resume() had the check inverted; fix that.
Fixes: 3e83eda467 ("HID: i2c-hid: Fix resume issue on Raydium touchscreen device")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is something that bothered us from a long time. When hid-input
doesn't know how to map a usage, it uses *_MISC. But there is something
else which increments the usage if the evdev code is already used.
This leads to few issues:
- some devices may have their ABS_X mapped to ABS_Y if they export a bad
set of usages (see the DragonRise joysticks IIRC -> fixed in a specific
HID driver)
- *_MISC + N might (will) conflict with other defined axes (my Logitech
H800 exports some multitouch axes because of that)
- this prevents to freely add some new evdev usages, because "hey, my
headset will now report ABS_COFFEE, and it's not coffee capable".
So let's try to kill this nonsense, and hope we won't break too many
devices.
I my headset case, the ABS_MISC axes are created because of some
proprietary usages, so we might not break that many devices.
For backward compatibility, a quirk HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE
is created and can be applied to any device that needs this behavior.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds a new driver for the Redragon Asura keyboard. The Asura
keyboard contains an error in the HID descriptor which causes all
modifier keys to be mapped to left shift. Additionally, we suppress
the creation of a second, not working, keyboard device.
Signed-off-by: Robert Munteanu <rombert@apache.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The CHPN0001 ACPI device has a _CID of PNP0C50 and even has the _DSM to
get the HID descriptor address, but it is not a HID device at all.
It uses its own protocol which is handled by the (still being upstreamed)
chipone_icn8505 driver. I guess the _CID and the _DSM are the result of
a copy and paste job when the vendor was building the ACPI tables.
Before this patch the i2c_hid_driver's probe function will fail with a
"hid_descr_cmd failed" error.
This commit makes the i2c_hid_driver's probe function instead silently
ignored devices with an ACPI id of CHPN0001.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Log an error in all error paths of i2c_hid_acpi_pdata() instead of having
the caller log a generic error.
This is a preparation patch for allowing i2c_hid_acpi_pdata() to fail
silently under certain conditions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When Rayd touchscreen resumed from S3, it issues too many errors like:
i2c_hid i2c-RAYD0001:00: i2c_hid_get_input: incomplete report (58/5442)
And all the report data are corrupted, touchscreen is unresponsive.
Fix this by re-sending report description command after resume.
Add device ID as a quirk.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The code path for recent Bluetooth devices omits an exit report which
resets all the values of the device.
Fixes: 4922cd26f0 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Doing `ioctl(HIDIOCGFEATURE)` in a tight loop on a hidraw device
and then disconnecting the device, or unloading the driver, can
cause a NULL pointer dereference.
When a hidraw device is destroyed it sets 0 to `dev->exist`.
Most functions check 'dev->exist' before doing its work, but
`hidraw_get_report()` was missing that check.
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit 581c448476 ("HID: input: map digitizer battery usage")
assumed that devices having input (qas opposed to feature) report for
battery strength would report the data on their own, without the need to
be polled by the kernel; unfortunately it is not so. Many wireless mice
do not send unsolicited reports with battery strength data and have to
be polled explicitly. As a complication, stylus devices on digitizers
are not normally connected to the base and thus can not be polled - the
base can only determine battery strength in the stylus when it is in
proximity.
To solve this issue, we add a special flag that tells the kernel
to avoid polling the device (and expect unsolicited reports) and set it
when report field with physical usage of digitizer stylus (HID_DG_STYLUS).
Unless this flag is set, and we have not seen the unsolicited reports,
the kernel will attempt to poll the device when userspace attempts to
read "capacity" and "state" attributes of power_supply object
corresponding to the devices battery.
Fixes: 581c448476 ("HID: input: map digitizer battery usage")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=198095
Cc: stable@vger.kernel.org
Reported-and-tested-by: Martin van Es <martin@mrvanes.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- 3rd generation Wacom Intuos BT device support from Aaron Armstrong
Skomra
- support for NSG-MR5U and NSG-MR7U devices from Todd Kelner
- multitouch Razer Blade Stealth support from Benjamin Tissoires
- Elantech touchpad support from Alexandrov Stansilav
- a few other scattered-around fixes and cleanups to drivers and
generic code
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (31 commits)
HID: google: Enable PM Full On mode when adjusting backlight
HID: google: add google hammer HID driver
HID: core: reset the quirks before calling probe again
HID: multitouch: do not set HID_QUIRK_NO_INIT_REPORTS
HID: core: remove the need for HID_QUIRK_NO_EMPTY_INPUT
HID: use BIT() macro for quirks too
HID: use BIT macro instead of plain integers for flags
HID: multitouch: remove dead zones of Razer Blade Stealth
HID: multitouch: export a quirk for the button handling of touchpads
HID: usbhid: extend the polling interval configuration to keyboards
HID: ntrig: document sysfs interface
HID: wacom: wacom_wac_collection() is local to wacom_wac.c
HID: wacom: generic: add the "Report Valid" usage
HID: wacom: generic: Support multiple tools per report
HID: wacom: Add support for 3rd generation Intuos BT
HID: core: rewrite the hid-generic automatic unbind
HID: sony: Add touchpad support for NSG-MR5U and NSG-MR7U remotes
HID: hid-multitouch: Use true and false for boolean values
HID: hid-ntrig: use true and false for boolean values
HID: logitech-hidpp: document sysfs interface
...
hammer LED backlight brightness is not getting set when USB
device is in suspend state.
This patch fixes the issue by requesting USB HID device to be
in FULLON mode, so that sending hardware output report and
hardware raw request won't fail to set brightness, and set
device back to NORMAL mode once this call returns.
Signed-off-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Google hammer HID driver. This driver allow us to control hammer
keyboard backlight and support future features.
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Given that now the quirk handling is done in hid-quirk.c, we can actually
reset the quirks before calling .probe(), so that the drivers do not need
to keep track of initial quirks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is set by default now, so there is no point setting it in the driver
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no real point of registering an empty input node.
This should be default, but given some drivers need the blank input
node to set it up during input_configured, we need to postpone
the check for hidinput_has_been_populated().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Razer Blade Stealth detects palms too aggressively and this creates
a dead zone around the touchpad. Users like being able to use their
entire touchpad, so we should probably not filter out the "palm" events
from the device and report them as regular touches, leaving the palm
detection up to the upper stack
Link: https://bugs.freedesktop.org/show_bug.cgi?id=105409
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of using the class name, we better have a specific quirk for it
so other classes can make use of it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For mouse and joystick devices user can change the polling interval
via usbhid.mousepoll and usbhid.jspoll.
Implement the same thing for keyboards, so user can
reduce(or increase) input latency this way.
This has been tested with a Cooler Master Devastator with
kbpoll=32, resulting in delay between events of 32 ms(values were taken
from evtest).
Signed-off-by: Filip Alac <filipalac@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Bluetooth reports contain multiple pen frames per report.
Each frame contains a flag indicating if the frame is valid.
Future Wacom devices with this type of report may contain HID
descriptors, add support for this usage to the generic codepath
of the Wacom driver.
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Wacom devices contain contain Pen and Pad usages in
the same report. Future devices of this type may utilize
HID Descriptors.
The generic code path of the Wacom driver previously
assumed pen, touch, and pad reports were delivered in
separate reports. This patch adds support for processing
each collection of a report separately, in order to support
reports with multiple tools.
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We actually can have the unbind/rebind logic in hid-core.c, leaving
only the match function in hid-generic.
This makes hid-generic simpler and the whole logic simpler too.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sony's NSG-MR5U and NSG-MR7U remote controls have a full keyboard and a
touchpad. The keyboard is already supported by the existing Linux
kernel and drivers but the touchpad is not recognized. This patch adds
the coded needed to bring full functionality to the touchpad.
Note that these remotes use the vendor code for SMK even though they are
Sony branded.
Known limitations
- The built-in accelerometers are not supported by these changes
- When the Drag (Fn) key is used as a mouse button, the button is
automatically released when the key begins repeating. There are two
workarounds for this 1) Use the button behind the touchpad instead of
the Drag (Fn) key or 2) Disable the key repeat functionality or
increase the key repeat delay.
Signed-off-by: Todd Kelner <tsopdump@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch enables the 6th button on the ELECOM EX-G M-XT4DRBK
trackball mouse.
This is a left handed EX-G variant which only comes in a wireless (D)
model. It has a total of 6 buttons but one of these is not available
because of how the HID descriptor is configured.
Signed-off-by: Tomasz Kramkowski <tk@the-tk.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch changes all references to ELECOM trackballs using their
series name to refer to them by their model name.
ELECOM provides multiple series of mice such as EX-G, HUGE, and DEFT.
Although it has not caused conflicts in the driver, there can be more
than one iteration of mice in each series. For example, there are 7
variants of EX-G trackballs but only three (M-XT3URBK, M-XT3DRBK, and
M-XT4DRBK) need a driver to work correctly.
There are also 4 DEFT series trackballs but two of them have the same
VID:PID as the other two. I picked the earlier model for the naming of
the PID macros.
Signed-off-by: Tomasz Kramkowski <tk@the-tk.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
K70 Vengeance sends garbage keypresses when changing backlight brightness.
This hooks to the existing corsair driver, which filters out those
invalid keypresses on similar devices in the input mapping code.
V2: Fix spelling.
Signed-off-by: Aaron Bottegal <aaronbottegal@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
gcc-8 reports
drivers/hid/uhid.c: In function 'uhid_dev_create2':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' output may
be truncated copying 127 bytes from a string of length 127
[-Wstringop-truncation]
The compiler require that the input param 'len' of strncpy() should be
greater than the length of the src string, so that '\0' is copied as
well. We can just use strlcpy() to avoid this warning.
Signed-off-by: Xiongfeng Wang <xiongfeng.wang@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't populate the const read-only array 'buf' on the stack but instead
make it static. Makes the object code smaller by 26 bytes:
Before:
text data bss dec hex filename
14378 2384 64 16826 41ba linux/drivers/hid/hid-asus.o
After:
text data bss dec hex filename
14296 2440 64 16800 41a0 linux/drivers/hid/hid-asus.o
(gcc version 7.2.0 x86_64)
[jkosina@suse.cz: change commit message slightly]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Follow the change of return type u32 of hid_report_len,
fix all the types of variables those get the return value of
hid_report_len to u32, and all other code already uses u32.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When size is negative, calling memset will make segment fault.
Declare the size as type u32 to keep memset safe.
size in struct hid_report is unsigned, fix return type of
hid_report_len to u32.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When convert char array with signed int, if the inbuf[x] is negative then
upper bits will be set to 1. Fix this by using u8 instead of char.
ret_size has to be at least 3, hid_input_report use it after minus 2 bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse sold by Corsair as the GLAIVE RGB gaming mouse has the same
problem with its HID reports as the Scimitar PRO RGB, so reuse the
same fix for the GLAIVE RGB.
Signed-off-by: Guus Sliepen <guus@sliepen.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is driver for usb touchpad found on HP Pavilion x2 10-p0xx laptop. On this
device keyboard and touchpad connected as a single usb device with two
interfaces: keyboard, which exposes ordinary keys and second interface is
touchpad which also contains FlightMode button and audio mute led (which
physically placed on keyboard for some reason).
Initially, this touchpad works in mouse emulation mode, this driver will switch
it to touchpad mode, which can track 5 fingers and can report coordinates for
two of them.
Signed-off-by: Alexandrov Stansilav <neko@nya.ai>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of doing additional checks and functional calls,
just get ACPI companion device directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for new CASSY devices to the ldusb driver. The
PIDs are also added to the ignore list in hid-quirks.
Signed-off-by: Karsten Koop <kkoop@ld-didactic.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull HID updates from Jiri Kosina:
- remove hid_have_special_driver[] entry hard requirement for any newly
supported VID/PID by a specific non-core hid driver, and general
related cleanup of HID matching core, from Benjamin Tissoires
- support for new Wacom devices and a few small fixups for already
supported ones in Wacom driver, from Aaron Armstrong Skomra and Jason
Gerecke
- sysfs interface fix for roccat driver from Dan Carpenter
- support for new Asus HW (T100TAF, T100HA, T200TA) from Hans de Goede
- improved support for Jabra devices, from Niels Skou Olsen
- other assorted small fixes and new device IDs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
HID: quirks: Fix keyboard + touchpad on Toshiba Click Mini not working
HID: roccat: prevent an out of bounds read in kovaplus_profile_activated()
HID: asus: Fix special function keys on T200TA
HID: asus: Add touchpad max x/y and resolution info for the T200TA
HID: wacom: Add support for One by Wacom (CTL-472 / CTL-672)
HID: wacom: Fix reporting of touch toggle (WACOM_HID_WD_MUTE_DEVICE) events
HID: intel-ish-hid: Enable Cannon Lake and Coffee Lake laptop/desktop
HID: elecom: rewrite report fixup for EX-G and future mice
HID: sony: Report DS4 version info through sysfs
HID: sony: Print reversed MAC address via %pMR
HID: wacom: EKR: ensure devres groups at higher indexes are released
HID: rmi: Support the Fujitsu R726 Pad dock using hid-rmi
HID: add quirk for another PIXART OEM mouse used by HP
HID: quirks: make array hid_quirks static
HID: hid-multitouch: support fine-grain orientation reporting
HID: asus: Add product-id for the T100TAF and T100HA keyboard docks
HID: elo: clear BTN_LEFT mapping
HID: multitouch: Combine all left-button events in a frame
HID: multitouch: Only look at non touch fields in first packet of a frame
HID: multitouch: Properly deal with Win8 PTP reports with 0 touches
...
Pull Wacom device driver updates. These don't have to go on top of the
hid_have_special_driver[] revamp, as the whole group is assumed to
have a special driver based on VID.
This series from Benjamin Tissoires finally removes one of the big PITAs
in the hid-core, which is the absolute need of having added all the new
device IDs into the horrid hid_have_special_driver[]
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
The Toshiba Click Mini uses an i2c attached keyboard/touchpad combo
(single i2c_hid device for both) which has a vid:pid of 04F3:0401,
which is also used by a bunch of Elan touchpads which are handled by the
drivers/input/mouse/elan_i2c driver, but that driver deals with pure
touchpads and does not work for a combo device such as the one on the
Toshiba Click Mini.
The combo on the Mini has an ACPI id of ELAN0800, which is not claimed
by the elan_i2c driver, so check for that and if it is found do not ignore
the device. This fixes the keyboard/touchpad combo on the Mini not working
(although with the touchpad in mouse emulation mode).
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We get the "new_profile_index" value from the mouse device when we're
handling raw events. Smatch taints it as untrusted data and complains
that we need a bounds check. This seems like a reasonable warning
otherwise there is a small read beyond the end of the array.
Fixes: 0e70f97f25 ("HID: roccat: Add support for Kova[+] mouse")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just like on the T100TA the T200TA HID descriptors for the 0xff32
Asus vendor usage page need a small fixup. But on the T200TA the HID
descriptors are larger because they have descrriptors for one more
(unused) HID report appended.
Extend the T100TA descriptor fixup to also check for the T200TA's
descriptors size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Asus T200TA uses the same USB device-id for its keyboard dock as the
T100TA, but the touchpad has a different size and corresponding different
max x/y values.
Add a separate asus_touchpad_info struct for the T200TA and select this
based on the DMI product-name (as we are already doing for the T100HA),
so that we report the correct info to userspace.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for the second-generation "One by Wacom" tablets. These
devices are similar to the last generation, but a slightly different size
and reporting a higher number of pressure levels.
Signed-off-by: Mx Jing <jingmingxuan@outlook.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Touch toggle softkeys send a '1' while pressed and a '0' while released,
requring the kernel to keep track of wether touch should be enabled or
disabled. The code does not handle the state transitions properly,
however. If the key is pressed repeatedly, the following four states
of states are cycled through (assuming touch starts out enabled):
Press: shared->is_touch_on => 0, SW_MUTE_DEVICE => 1
Release: shared->is_touch_on => 0, SW_MUTE_DEVICE => 1
Press: shared->is_touch_on => 1, SW_MUTE_DEVICE => 0
Release: shared->is_touch_on => 1, SW_MUTE_DEVICE => 1
The hardware always properly enables/disables touch when the key is
pressed but applications that listen for SW_MUTE_DEVICE events to provide
feedback about the state will only ever show touch as being enabled while
the key is held, and only every-other time. This sequence occurs because
the fallthrough WACOM_HID_WD_TOUCHONOFF case is always handled, and it
uses the value of the *local* is_touch_on variable as the value to
report to userspace. The local value is equal to the shared value when
the button is pressed, but equal to zero when the button is released.
Reporting the shared value to userspace fixes this problem, but the
fallthrough case needs to update the shared value in an incompatible
way (which is why the local variable was introduced in the first place).
To work around this, we just handle both cases in a single block of code
and update the shared variable as appropriate.
Fixes: d793ff8187 ("HID: wacom: generic: support touch on/off softkey")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Aaron Skomra <aaron.skomra@wacom.com>
Tested-by: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added PCI ID for Cannon Lake and Coffee Lake laptop/desktop skews.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch rewrites the mouse report fixup used for the DEFT and HUGE
elecom trackballs in order to make it generic enough to fix other
elecom mice with similar issues. This patch also uses this new report
fixup function to fix the Elecom EX-G trackball which has 6 physical
buttons and a similar issue to the other two mice.
Elecom's track record has so far shown that they like to re-use the
same report descriptor for multiple different mice regardless of the
number of buttons the mouse has. This means that the missing buttons
on multiple mice can be fixed in one function without introducing
phantom buttons which would in turn cause the number of mouse buttons
to be misreported to userspace.
This patch drops the very verbose report descriptor "diff" comment for
a more abridged yet hopefully just as informative generic version.
Signed-off-by: Tomasz Kramkowski <tk@the-tk.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Report DS4 firmware and hardware version through sysfs for both
USB and Bluetooth. This information is important for userspace
in particular for device specific quirks (e.g. in Bluetooth stacks).
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reversed MAC addresses can be printed directly using %pMR specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Roderick Colenbrander <roderick.colenbranderer@sony.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Background: ExpressKey Remotes communicate their events via usb dongle.
Each dongle can hold up to 5 pairings at one time and one EKR (identified
by its serial number) can unfortunately be paired with its dongle
more than once. The pairing takes place in a round-robin fashion.
Input devices are only created once per EKR, when a new serial number
is seen in the list of pairings. However, if a device is created for
a "higher" paring index and subsequently a second pairing occurs at a
lower pairing index, unpairing the remote with that serial number from
any pairing index will currently cause a driver crash. This occurs
infrequently, as two remotes are necessary to trigger this bug and most
users have only one remote.
As an illustration, to trigger the bug you need to have two remotes,
and pair them in this order:
1. slot 0 -> remote 1 (input device created for remote 1)
2. slot 1 -> remote 1 (duplicate pairing - no device created)
3. slot 2 -> remote 1 (duplicate pairing - no device created)
4. slot 3 -> remote 1 (duplicate pairing - no device created)
5. slot 4 -> remote 2 (input device created for remote 2)
6. slot 0 -> remote 2 (1 destroyed and recreated at slot 1)
7. slot 1 -> remote 2 (1 destroyed and recreated at slot 2)
8. slot 2 -> remote 2 (1 destroyed and recreated at slot 3)
9. slot 3 -> remote 2 (1 destroyed and not recreated)
10. slot 4 -> remote 2 (2 was already in this slot so no changes)
11. slot 0 -> remote 1 (The current code sees remote 2 was paired over in
one of the dongle slots it occupied and attempts
to remove all information about remote 2 [1]. It
calls wacom_remote_destroy_one for remote 2, but
the destroy function assumes the lowest index is
where the remote's input device was created. The
code "cleans up" the other remote 2 pairings
including the one which the input device was based
on, assuming they were were just duplicate
pairings. However, the cleanup doesn't call the
devres release function for the input device that
was created in slot 4).
This issue is fixed by this commit.
[1] Remote 2 should subsequently be re-created on the next packet from the
EKR at the lowest numbered slot that it occupies (here slot 1).
Fixes: f9036bd436 ("HID: wacom: EKR: use devres groups to manage resources")
Cc: stable <stable@vger.kernel.org> #4.9
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Fujitsu R726 Pad has an optional USB keyboard dock which contains
a Synaptics touchpad. The dock identifies itself as a
Primax Rezel Tablet Keyboard.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- two cosmetic fixes from Daniel Axtens and Hans de Goede
- fix for I2C command mismatch fix for cp2112 driver from Eudean Sun
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: lower log level for unknown main item tags to warnings
HID: holtekff: move MODULE_* parameters out of #ifdef block
HID: cp2112: Fix I2C_BLOCK_DATA transactions
This mouse keep disconnecting in runleve 3 like below, add it needs the
quirk to mute the anoying messages.
[ 111.230555] usb 2-2: USB disconnect, device number 6
[ 112.718156] usb 2-2: new low-speed USB device number 7 using xhci_hcd
[ 112.941594] usb 2-2: New USB device found, idVendor=03f0, idProduct=094a
[ 112.984866] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 113.027731] usb 2-2: Product: HP USB Optical Mouse
[ 113.069977] usb 2-2: Manufacturer: PixArt
[ 113.113500] input: PixArt HP USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.0/0003:03F0:094A.0002/input/input14
[ 113.156787] hid-generic 0003:03F0:094A.0002: input: USB HID v1.11 Mouse [PixArt HP USB Optical Mouse] on usb-0000:00:14.0-2/input0
[ 173.262642] usb 2-2: USB disconnect, device number 7
[ 174.750244] usb 2-2: new low-speed USB device number 8 using xhci_hcd
[ 174.935740] usb 2-2: New USB device found, idVendor=03f0, idProduct=094a
[ 174.990435] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 175.014984] usb 2-2: Product: HP USB Optical Mouse
[ 175.037886] usb 2-2: Manufacturer: PixArt
[ 175.061794] input: PixArt HP USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.0/0003:03F0:094A.0003/input/input15
[ 175.084946] hid-generic 0003:03F0:094A.0003: input: USB HID v1.11 Mouse [PixArt HP USB Optical Mouse] on usb-0000:00:14.0-2/input0
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Given all the effort distros have done with splash-screens to give
users a nice clean boot experience, we really want dmesg --level=err
to not print anything unless there is a real problem with either the
hardware or the kernel. Buggy HID descriptors unfortunately happen
all too often, so lower the log level to warning keep the console
clear of error messages such as:
[ 441.079664] apple 0005:05AC:0239.0003: unknown main item tag 0x0
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Array hid_quirks is local to the source and does not need to be in
global scope, so make it static.
Cleans up sparse warning:
drivers/hid/hid-quirks.c:29:28: warning: symbol 'hid_quirks' was not
declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The current hid-multitouch driver only allow the report of two
orientations, vertical and horizontal. We use the Azimuth orientation
usage 0x3F under the Digitizer usage page to report orientation if the
device supports it.
Changelog:
v1 -> v2:
- Fix commit message.
- Remove resolution reporting for ABS_MT_ORIENTATION.
v2 -> v3:
- Fix commit message.
v3 -> v4:
- Fix ABS_MT_ORIENTATION ABS param range.
- Don't set ABS_MT_ORIENTATION in ABS_DG_HEIGHT when it is already
set by ABS_DG_AZIMUTH.
v4 -> v5:
- Improve multi-touch-protocol.rst documentation.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The T100TAF and T100HA keyboard docks have the same special keys and
custom protocol multitouch touchpad as the T100TA, but use a different
product id.
The T100TAF and T100HA both use the same product id, but the T100HA's
touchpad has a different coordinate range.
This commits adds supports for the new USB id and uses a dmi-check to
determine if we're dealing with the T100TAF or T100HA.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=197849
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If you compile with:
CONFIG_HID_HOLTEK=m
CONFIG_HOLTEK_FF is not set
You get the following warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/hid/hid-holtekff.o
see include/linux/module.h for more information
Fix this by moving the module info out of the #ifdef CONFIG_HOLTEK_FF
block and into the un-guarded part of the file.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Anssi Hannula <anssi.hannula@iki.fi>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ELO devices have one Button usage in GenDesk field, which makes hid-input map
it to BTN_LEFT; that confuses userspace, which then considers the device to be
a mouse/touchpad instead of touchscreen.
Fix that by unmapping BTN_LEFT and keeping only BTN_TOUCH in place.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to the Win8 Precision Touchpad spec, inside the HID_UP_BUTTON
usage-page usage 1 is for a clickpad getting clicked, 2 for an external
left button and 3 for an external right button. Since Linux uses
BTN_LEFT for a clickpad being clicked we end up mapping both usage 1
and 2 to BTN_LEFT and if a single report contains both then we ended
up always reporting the value of both in a single SYN, e.g. :
BTN_LEFT 1, BTN_LEFT 0, SYN. This happens for example with Hantick
HTT5288 i2c mt touchpads.
This commit fixes this by not immediately reporting left button when we
parse the report, but instead storing or-ing together the values and
reporting the result from mt_sync_frame() when we've a complete frame.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices in "single finger hybrid mode" will send one report per finger,
on some devices only the first report of such a multi-packet frame will
contain a value for BTN_LEFT, in subsequent reports (if multiple fingers
are down) the value is always 0, causing hid-mt to report BTN_LEFT going
1 - 0 - 1 - 0 when pressing a clickpad and putting down a second finger.
This happens for example on USB 0603:0002 mt touchpads.
This commit fixes this by only reporting non touch fields for the first
packet of a (possibly) multi-packet frame.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Windows Precision Touchpad spec "Figure 4 Button Only Down and Up"
and "Table 9 Report Sequence for Button Only Down and Up" indicate
that the first packet of a (possibly hybrid mode multi-packet) frame
may contain a contact-count of 0 if only a button is pressed and no
fingers are detected.
This means that a value of 0 for contact-count is a valid value and
should be used as expected contact count when it is the first packet
(num_received == 0), as extra check to make sure that this is the first
packet of a buttons only frame, we also check that the timestamp is
different.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix alphabetic sorting of mt_devices hid_device_id table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The existing driver erroneously treats I2C_BLOCK_DATA and BLOCK_DATA
commands the same.
For I2C_BLOCK_DATA reads, the length of the read is provided in
data->block[0], but the length itself should not be sent to the slave. In
contrast, for BLOCK_DATA reads no length is specified since the length
will be the first byte returned from the slave. When copying data back
to the data buffer, for an I2C_BLOCK_DATA read we have to take care not to
overwrite data->block[0] to avoid overwriting the length. A BLOCK_DATA
read doesn't have this concern since the first byte returned by the device
is the length and belongs in data->block[0].
For I2C_BLOCK_DATA writes, the length is also provided in data->block[0],
but the length itself is not sent to the slave (in contrast to BLOCK_DATA
writes where the length prefixes the data sent to the slave).
This was tested on physical hardware using i2cdump with the i and s flags
to test the behavior of I2C_BLOCK_DATA reads and BLOCK_DATA reads,
respectively. Writes were not tested but the I2C_BLOCK_DATA write change
is pretty simple to verify by inspection.
Signed-off-by: Eudean Sun <eudean@arista.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The property "post-power-on-delay-ms" allows a platform to specify
the delay needed after power-on, but only via device trees currently.
Use device_property_* instead of of_* reads to allow ACPI systems to
also provide the same information. This is useful for Wacom hardware
on ACPI systems.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Userspace expects to receive tool type and serial number information
for the active pen in the very first kernel report, if such data is
supported by the hardware. While this expectation is not an issue for
EMR devices, AES sensors will often send several packets worth of in-
range data before relaying type/serial data to the kernel. Sending this
data "late" can result in proximity-tracking issues by xf86-input-wacom,
or an inability to distinguish different pens by input-wacom.
Options for dealing with this situation include ignoring reports from
the tablet until we get the necessary data, or using the information
from the last-seen pen instead of the (eventual) real data. Neither
option is particularly attractive: the former results in truncated
strokes and the latter causes issues with switching between pens.
This commit instead opts to queue up events with missing information
until we receive a report which contains it. At that point, we can
update the driver's state variables (id[0] and serial[0]) and replay
the queued events.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current AES sensors relay tool type and serial number information with
a different set of usages than those prescribed by the modern (i.e.
MobileStudio Pro and newer) EMR tablet standard. To ensure the driver
properly understands these usages, we modify them to be compatible.
The identifying information is split across three consecutive fields:
a 16-bit WACOM_HID_WT_SERIALNUMBER (which is more accurately described
as WACOM_HID_WD_TOOLTYPE), a 32-bit HID_DG_TOOLSERIALNUMBER, and an
8-bit 0xFF000000 (which should be WACOM_HID_WD_SERIALHI). While we're
at it, we also define proper min/max values since may may be undefined
on some devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a hid-jabra driver to the list of special drivers in hid-core. The
driver prevents vendor defined HID usages (FF00-FFFF) in Jabra devices
from being mapped to input events, that become unintended mouse events
in the X11 server.
Signed-off-by: Niels Skou Olsen <nolsen@jabra.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Two Jabra speakerphone devices were added to the ignore list in 2013,
because the device HID interfaces didn't work well with kernel usbhid
driver, and could cause volume key event storm.
See the original commit:
Commit 31b9779cb2 ("HID: ignore Jabra speakerphones HID interface")
Modify hid_lookup_quirk() to consider the firmware version of these two
devices, so that only versions older than a known good version are
ignored.
Signed-off-by: Niels Skou Olsen <nolsen@jabra.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Most HID devices behave properly when they are used with hid-generic.
Since kernel v4.12, we do not poll for input reports at plug in, so
hid-generic should behave properly with all HID devices.
There has been a long standing list of HID devices that have a special
driver. It used to be just a few, but with time, this list went too big,
and we can not ask users to know which HID special driver will pick up
their device.
We can teach hid-generic to be nice with others. If a device is not
explicitly marked with HID_QUIRK_HAVE_SPECIAL_DRIVER, we can allow
hid-generic to pick up the device as long as no other loaded HID driver
will match the device.
When the special driver appears, hid-generic can step back and let
the special driver handling the device. In case this special driver
is removed, this good old pal of hid-generic will rebind to the device.
This basically makes the list hid_have_special_driver[] useless. It
still allows to not see a hid-generic driver bound and removed during
boot, so we can keep it around.
This will also help other people to have a special HID driver without
the need of recompiling hid-core.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Better having all the devices quirks in one place.
Note that this change introduces an initial lookup for the device in
hid_gets_squirk(), which should not theoretically be required, but which
actually allows to not have to reparse the list of ignored devices
if we call hid_lookup_quirks twice.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is better to centralize the information of special devices in one
single file. Instead of manually parsing the list of devices that
have a special driver or those that need to be ignored, introduce
HID_QUIRK_HAVE_SPECIAL_DRIVER and set the correct quirks while fetching
those quirks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
usbhid has a list of dynamic quirks in addition to a list of static quirks.
There is not much USB specific in that, so move this part of the module
in core so we can have one central place for quirks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
Pull HID updates from Jiri Kosina:
- high resolution mode for Dell canvas support, from Benjamin Tissoires
- pen handling fixes for the Wacom driver, from Jason Gerecke
- i2c-hid: Apollo-Lake based laptops improvements, from Hans de Goede
- Input/Core: eraser tool support, from Ping Cheng
- new ALPS touchpad (T4, found currently on HP EliteBook 1000, Zbook
Stduio and HP Elite book x360) supportm from Masaki Ota
- other smaller assorted fixes
* 'for-linus' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (33 commits)
HID: cp2112: fix broken gpio_direction_input callback
HID: cp2112: fix interface specification URL
HID: Wacom: switch Dell canvas into highres mode
HID: wacom: generic: Send BTN_STYLUS3 when both barrel switches are set
HID: sony: Fix SHANWAN pad rumbling on USB
HID: i2c-hid: Add no-irq-after-reset quirk for 0911:5288 device
HID: add backlight level quirk for Asus ROG laptops
HID: cp2112: add HIDRAW dependency
HID: Add ID 044f:b605 ThrustMaster, Inc. force feedback Racing Wheel
HID: hid-logitech: remove redundant assignment to pointer value
HID: wacom: generic: Recognize WACOM_HID_WD_PEN as a type of pen collection
HID: rmi: Check that a device is a RMI device before calling RMI functions
HID: add multi-input quirk for GamepadBlock
HID: alps: add new U1 device ID
HID: alps: add support for Alps T4 Touchpad device
HID: alps: remove variables local to u1_init() from the device struct
HID: alps: properly handle max_fingers and minimum on X and Y axis
HID: alps: Separate U1 device code
HID: alps: delete unnecessary struct u1_dev devInfo
HID: usbhid: Convert timers to use timer_setup()
...
- High resolution mode for DEll canvas support, from Benjamin Tissoires
- A lot of improvements to pen handling in the Wacom driver, from Jason Gerecke
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- cp2112: GPIO error handling and Kconfig fixes from Sébastien Szymanski
- i2c-hid: fixup / quirk for Apollo-Lake based laptops, from Hans de Goede
- Input/Core: add eraser tool support, from Ping Cheng
- small assorted code fixes
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When everything goes smoothly, ret is set to 0 which makes the function
to return EIO error.
Fixes: 8e9faa1546 ("HID: cp2112: fix gpio-callback error handling")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Dell Canvas exports 2 collections for the Pen part. The only
difference between the 2 is that the default one has half the resolution
of the second one.
The Windows driver switches the tablet into the second mode, so we should
behave the same.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Wacom Pro Pen 3D includes a third barrel switch which is intended to
be particularly useful in applications where one frequency uses pan, zoom,
and rotate to navigate around a scene or model. The pen is compatible with
the MobileStudio Pro, 2nd-gen Intuos Pro, and Cintiq Pro. When the third
button is pressed, these devices set both the HID_DG_BARRELSWITCH and
HID_DG_BARRELSWITCH2 usages since their HID descriptors do not include a
usage specific to the button.
Rather than send both BTN_STYLUS and BTN_STYLUS2 when the third button is
pressed, userspace (libinput) has requested that we detect this condition
and report a newly-defined BTN_STYLUS3 event instead. We could define a
quirk specific to devices compatible with the Pro Pen 3D, but the liklihood
of seeing both barrel switch bits set with other pens/devices is low enough
to not worry about (pens mechanically prevent accidental activation of
multiple switches).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The SHANWAN PS3 clone joypad will start its rumble motors as soon as
it is plugged in via USB. As the additional USB interrupt does nothing on
the original PS3 Sixaxis joypads, and makes a number of other
clone joypads actually start sending data, disable that call for
the SHANWAN so the rumble motors aren't started on plug.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Several cheap Apollo Lake based laptops / 2-in-1s use an i2c-hid mt
touchpad which is advertised by the DSDT with an ACPI HID of "SYNA3602",
this touchpad can be found on e.g. the Cube Thinker and the EZBook 3 Pro.
On my "T-bao Tbook air" the i2c-hid driver fails to bind to this touchpad:
"i2c_hid i2c-SYNA3602:00: failed to reset device.".
After some debuging this it seems that this touchpad simply never sends
an interrupt after a reset as expected by the i2c hid driver. This commit
adds a quirk for this device, making i2c_hid_command sleep 100ms after
a reset instead of waiting for an irq, fixing i2c-hid failing to bind to
this touchpad.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On laptops such as Asus GL553VD, setting keyboard backlight levels
does not work. This change enables F3/F4 keys to set backlight levels
(from 0 to 3, total 4 levels) on such laptops.
It is intended only to the following device: 0x0b05 1854:
P: Vendor=0b05 ProdID=1854 Rev=03.02
S: Manufacturer=ITE Tech. Inc.
S: Product=ITE Device(8910)
[jkosina@suse.cz: massage changelog a little bit]
Signed-off-by: Mustafa C Kuscu <mustafakuscu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Otherwise, with HIDRAW=n, the probe function crashes because of null
dereference of hdev->hidraw.
Cc: stable@vger.kernel.org
Fixes: 42cb6b35b9 ("HID: cp2112: use proper hidraw name with minor number")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add ID 044f:b605 ThrustMaster, Inc. force feedback Racing Wheel
Signed-off-by: Viktor Chapliev <viktor-tch@yandex.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
The pointer value is being assigned a value and this is never read, and later
on it is being assigned a new value. This the first assignment is redundant
and can be removed and hence also the variables report and report_list. Cleans
up the clang warning: Value stored to 'value' during its initialization is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The WACOM_PEN_FIELD macro is used to determine if a given HID field should be
associated with pen input. This field includes several known collection types
that Wacom pen data is contained in, but the WACOM_HID_WD_PEN application
collection type is notably missing. This can result in fields within this
kind of collection being completely ignored by the `wacom_usage_mapping`
function, preventing the later '*_event' functions from being notified about
changes to their value.
Fixes: c9c095874a ("HID: wacom: generic: Support and use 'Custom HID' mode and usages")
Fixes: ac2423c975 ("HID: wacom: generic: add vendor defined touch")
Cc: stable@vger.kernel.org
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid-rmi driver may handle non rmi devices on composite USB devices.
Callbacks need to make sure that the current device is a RMI device before
calling RMI specific functions. Most callbacks already have this check, but
this patch adds checks to the remaining callbacks.
Reported-by: Hendrik Langer <hendrik.langer@gmx.de>
Tested-by: Hendrik Langer <hendrik.langer@gmx.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The GamepadBlock game controller adapter needs HID_QUIRK_MULTI_INPUT
to split it up into two input devices. Without this quirk the
adapter is falsely recognized as only one device and mixes up the
inputs of the two connected controllers.
Signed-off-by: Florian Mueller <contact@petrockblock.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add new U1 device Product ID This device is used on HP Elite book x360 series.
[jkosina@suse.cz: update changelog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- Define T4 device specification value for support T4 device.
- Creeate "t4_contact_data" and "t4_input_report" structure for decoding and
storing T4-specific data
- Create "t4_calc_check_sum()" function for calculating checksum value to send
to the device. T4 needs to send this value when reading or writing device
address value.
- Create "t4_read_write_register()" function for reading and writing device
address value.
- Create "t4_raw_event()" function for decodin XYZ, palm and button data.
- Replace "MAX_TOUCHES" fixed variable to "max_fingers" variable.
- Add T4 devuce product ID. (0x120C)
T4 device is used on HP EliteBook 1000 series and Zbook Stduio
[jkosina@suse.cz: rewrite changelog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move dev_ctrl, dev_type, sen_line_num_x, sen_line_num_y, pitch_x, pitch_y,
resolution, btn_info from u1_dev structure to "u1_init()", because these
variables are only used in there.
[jkosina@suse.cz: rewrite changelog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Create x_min, y_min and max_fingers variables for set correct XY minimum value
and the number of max finger on each devices.
[jkosina@suse.cz: update shortlog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Create 'static int u1_init()' and factor out U1 device initialization code from
main initialization and introduce per-device 'has_sp' flag.
[jkosina@suse.cz: rewrite changelog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fix for potential out-of-bounds memory access (found by fuzzing,
likely requires specially crafted device to trigger) by Jaejoong Kim
- two new device IDs for elecom driver from Alex Manoussakis
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-elecom: extend to fix descriptor for HUGE trackball
HID: usbhid: fix out-of-bounds bug
Trivial fix to spelling mistake in hid_info message and add line break
to split an overly long line to clean up a checkpatch warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In addition to DEFT, Elecom introduced a larger trackball called HUGE, in
both wired (M-HT1URBK) and wireless (M-HT1DRBK) versions. It has the same
buttons and behavior as the DEFT. This patch adds the two relevant USB IDs
to enable operation of the three Fn buttons on the top of the device.
Cc: Diego Elio Petteno <flameeyes@flameeyes.eu>
Signed-off-by: Alex Manoussakis <amanou@gnu.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid descriptor identifies the length and type of subordinate
descriptors for a device. If the received hid descriptor is smaller than
the size of the struct hid_descriptor, it is possible to cause
out-of-bounds.
In addition, if bNumDescriptors of the hid descriptor have an incorrect
value, this can also cause out-of-bounds while approaching hdesc->desc[n].
So check the size of hid descriptor and bNumDescriptors.
BUG: KASAN: slab-out-of-bounds in usbhid_parse+0x9b1/0xa20
Read of size 1 at addr ffff88006c5f8edf by task kworker/1:2/1261
CPU: 1 PID: 1261 Comm: kworker/1:2 Not tainted
4.14.0-rc1-42251-gebb2c2437d80 #169
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
print_address_description+0x78/0x280 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351
kasan_report+0x22f/0x340 mm/kasan/report.c:409
__asan_report_load1_noabort+0x19/0x20 mm/kasan/report.c:427
usbhid_parse+0x9b1/0xa20 drivers/hid/usbhid/hid-core.c:1004
hid_add_device+0x16b/0xb30 drivers/hid/hid-core.c:2944
usbhid_probe+0xc28/0x1100 drivers/hid/usbhid/hid-core.c:1369
usb_probe_interface+0x35d/0x8e0 drivers/usb/core/driver.c:361
really_probe drivers/base/dd.c:413
driver_probe_device+0x610/0xa00 drivers/base/dd.c:557
__device_attach_driver+0x230/0x290 drivers/base/dd.c:653
bus_for_each_drv+0x161/0x210 drivers/base/bus.c:463
__device_attach+0x26e/0x3d0 drivers/base/dd.c:710
device_initial_probe+0x1f/0x30 drivers/base/dd.c:757
bus_probe_device+0x1eb/0x290 drivers/base/bus.c:523
device_add+0xd0b/0x1660 drivers/base/core.c:1835
usb_set_configuration+0x104e/0x1870 drivers/usb/core/message.c:1932
generic_probe+0x73/0xe0 drivers/usb/core/generic.c:174
usb_probe_device+0xaf/0xe0 drivers/usb/core/driver.c:266
really_probe drivers/base/dd.c:413
driver_probe_device+0x610/0xa00 drivers/base/dd.c:557
__device_attach_driver+0x230/0x290 drivers/base/dd.c:653
bus_for_each_drv+0x161/0x210 drivers/base/bus.c:463
__device_attach+0x26e/0x3d0 drivers/base/dd.c:710
device_initial_probe+0x1f/0x30 drivers/base/dd.c:757
bus_probe_device+0x1eb/0x290 drivers/base/bus.c:523
device_add+0xd0b/0x1660 drivers/base/core.c:1835
usb_new_device+0x7b8/0x1020 drivers/usb/core/hub.c:2457
hub_port_connect drivers/usb/core/hub.c:4903
hub_port_connect_change drivers/usb/core/hub.c:5009
port_event drivers/usb/core/hub.c:5115
hub_event+0x194d/0x3740 drivers/usb/core/hub.c:5195
process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119
worker_thread+0x221/0x1850 kernel/workqueue.c:2253
kthread+0x3a1/0x470 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431
Cc: stable@vger.kernel.org
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
(introduced by 686fef928b ("timer: Prepare to change timer callback
argument type")) to pass the timer pointer explicitly. Adds pointer back to
hid_device for multitouch.
[jkosina@suse.cz: extend changelog a little bit as asked for by Benjamin]
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3e70969e44.
This commit causes a few problems for userspace. The most noteworthy are
problems related to the distinguishing of different pens and pointer jumps
when entering proximity. Userspace is written with the expectation that a
pen will provide its tool ID and serial number (if available) in the very
first in-prox report. By sending BTN_TOOL_PEN when the tablet starts
communicating rather than waiting until a tool ID/serial number is
available, userspace ends up treating all pens as being the same and
lacking a serial number. Similarly, userspace assumes that the first
report will contain X/Y data, but by marking the pen as being in-prox
without an X/Y coordinate, userspace ends up warping the pen to the last-
known X/Y location. As of commit 5b40104edf ("HID: wacom: generic: Reset
events back to zero when pen leaves") this means warping to (0,0).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID subsystem fixes from Jiri Kosina:
- buffer management size fix for i2c-hid driver, from Adrian Salido
- tool ID regression fixes for Wacom driver from Jason Gerecke
- a few small assorted fixes and a few device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: multitouch: Support ALPS PTP stick with pid 0x120A"
HID: hidraw: fix power sequence when closing device
HID: wacom: Always increment hdev refcount within wacom_get_hdev_data
HID: wacom: generic: Clear ABS_MISC when tool leaves proximity
HID: wacom: generic: Send MSC_SERIAL and ABS_MISC when leaving prox
HID: i2c-hid: allocate hid buffers for real worst case
HID: rmi: Make sure the HID device is opened on resume
HID: multitouch: Support ALPS PTP stick with pid 0x120A
HID: multitouch: support buttons and trackpoint on Lenovo X1 Tab Gen2
HID: wacom: Correct coordinate system of touchring and pen twist
HID: wacom: Properly report negative values from Intuos Pro 2 Bluetooth
HID: multitouch: Fix system-control buttons not working
HID: add multi-input quirk for IDC6680 touchscreen
HID: wacom: leds: Don't try to control the EKR's read-only LEDs
HID: wacom: bits shifted too much for 9th and 10th buttons
pr_err() messages should terminated with a new-line to avoid
other messages being concatenated onto the end.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some tablets report eraser usage to indicate the eraser tool tip
is touching the surface. But, hidinput_configure_usage didn't
support the usage, which led it falls into default as ABS_MISC.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Computes and forwards the device timestamp according to the specification.
Many devices use a 16-bit timestamp field, with a resolution of 100us,
therefore rolling around very frequently (every 6.5 seconds). To make sure
there is no ambiguity, the timestamp reported to the input stack reset to
0 whenever the time between 2 received events is greater than
MAX_TIMESTAMP_INTERVAL (1 second).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add descriptive info to prompt string so that someone can know what
a Retrode is. Drop an unneeded blank line.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit fcaa4a07d2.
As noted by Masaki [1], 0x120A + trackpoint will not be used in mass
production machines, so remove the ID accordingly.
[1] http://www.spinics.net/lists/linux-input/msg53222.html
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We should not try to bring HID device out of full power state before
calling hid_hw_close(), so that transport driver operates on powered up
device (making this inverse of the opening sequence).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wacom_get_hdev_data function is used to find and return a reference to
the "other half" of a Wacom device (i.e., the touch device associated with
a pen, or vice-versa). To ensure these references are properly accounted
for, the function is supposed to automatically increment the refcount before
returning. This was not done, however, for devices which have pen & touch
on different interfaces of the same USB device. This can lead to a WARNING
("refcount_t: underflow; use-after-free") when removing the module or device
as we call kref_put() more times than kref_get(). Triggering an "actual" use-
after-free would be difficult since both devices will disappear nearly-
simultaneously. To silence this warning and prevent the potential error, we
need to increment the refcount for all cases within wacom_get_hdev_data.
Fixes: 41372d5d40 ("HID: wacom: Augment 'oVid' and 'oPid' with heuristics for HID_GENERIC")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for Fn keys on Asus ROG G752 laptop.
The report descriptor is broken so I fixed it.
Tested on an Asus G752VT.
Resent fix white space fixes
Signed-off-by: Maxime Bellengé <maxime.bellenge@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As a pen leaves, we need to be sure to reset all events back to zero
so that userspace is able to get the complete pen state when it enters
proximity again.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a pen is first able to to be sensed by the tablet, we would like
to inform userspace that a tool is nearby so that it can attempt to
perform palm rejection. Unfortunately, we don't know any information
about the tool that is nearby, so the best we can do is send a prox
event for a generic BTN_TOOL_PEN. If the pen later comes closer and
enters proximity, we can determine the actual tool type and send
BTN_TOOL_PEN out of prox if necessary.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The legacy Intuos codepath and tablet behavior (e.g. the 1st-gen Intuos
Pro, Cintiq 27, etc.) would result in a BTN_TOOL_* event not being cleared
to zero until the tool had completely left the sensing range of the
tablet. Before the final "out of prox" packet would be sent, zero or
more "in range" packets could be sent to indicate that a pen was still
detectable but not within a useful distance. These "in range" packets
were used by the driver to keep touch input disabled at greater pen
distances. In addition to keeping the `stylus_in_proximity` flag set,
the driver would leave the current BTN_TOOL_* marked as being in
proximity as well.
The new HID codepath also sets `stylus_in_proximity` based on the "sense"
flag, but does not leave the current BTN_TOOL_* marked as being in prox.
This information is potentially useful to for a future userspace-based
palm rejection, so this patch modifies the driver to continue sending it.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The terminology used to describe the various degrees of pen proximity
within the wacom_wac_pen_report function does not match that used elsewhere
in the generic codepath. Specifically, the names of the variables "prox"
and "range" were inspired by the non-generic codepaths. To make the generic
codepath internally consistent, replace these terms with "range" and "sense"
respectively.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The tool ID information sent in ABS_MISC is expected to be reset to 0
when a tool leaves proximity. Not doing this can cause problems if a
tool is removed and then re-introduced. Kernel event filtering will
prevent the (identical) ABS_MISC event from being sent when the tool
re-enters proxmity. This can cause userspace to not properly set the
tool ID.
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable # v4.10 <stable@vger.kernel.org>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The latest generation of pro devices (MobileStudio Pro, 2nd-gen Intuos
Pro, Cintiq Pro) send a serial number of '0' whenever the pen is too far
away for reliable communication. Userspace defines that a serial number
of '0' is invalid, so we need to be careful not to actually forward
this value. Additionally, since EMR ISDv4 devices do not support serial
numbers or tool IDs, we'd like to not send these events if they aren't
necessary.
The existing code achieves these goals by adding a check for a non-zero
serial number within the wacom_wac_pen_report function. The MSC_SERIAL
and ABS_MISC events are only sent if the serial number is non-zero. This
code fails, however when the pen for a pro device leaves proximity. When
the pen leaves prox and the tablet sends a serial of 0, wacom_wac_pen_event
dutifully clears the serial number. When wacom_wac_pen_report is called,
it does not send either the MSC_SERIAL of the exiting tool nor an ABS_MISC
event.
This patch prevents the wacom_wac_pen_event function from clearing an
already-set serial number. This ensures that we have the serial number
handy when exiting proximity, but requires us to manually clear it
afterwards to ensure the driver does not send stale data (e.g. when
switching between AES pens that report a serial nubmer of 0 for the
first few fully in-proximity packets).
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable # v4.10 <stable@vger.kernel.org>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The buffer allocation is not currently accounting for an extra byte for
the report id. This can cause an out of bounds access in function
i2c_hid_set_or_send_report() with reportID > 15.
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Salido <salidoa@google.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
So it looks like that suspend/resume has actually always been broken on
hid-rmi. The fact it worked was a rather silly coincidence that was
relying on the HID device to already be opened upon resume. This means
that so long as anything was reading the /dev/input/eventX node for for
an RMI device, it would suspend and resume correctly. As well, if
nothing happened to be keeping the HID device away it would shut off,
then the RMI driver would get confused on resume when it stopped
responding and explode.
So, call hid_hw_open() in rmi_post_resume() so we make sure that the
device is alive before we try talking to it.
This fixes RMI device suspend/resume over HID.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196851
[jkosina@suse.cz: removed useless hunk that was zero-initializing 'ret']
Signed-off-by: Lyude <lyude@redhat.com>
Cc: Andrew Duggan <aduggan@synaptics.com>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
-----BEGIN PGP SIGNATURE-----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=fNM2
-----END PGP SIGNATURE-----
Merge tag 'media/v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Brazil's Independence Day pull request :-)
This is one of the biggest media pull requests, with 625 patches
affecting almost all parts of media (RC, DVB, V4L2, CEC, docs).
This contains:
- A lot of new drivers:
* DVB frontends: mxl5xx, stv0910, stv6111;
* camera flash: as3645a led driver;
* HDMI receiver: adv748X;
* camera sensor: Omnivision 6650 5M driver (ov6650);
* HDMI CEC: ao-cec meson driver;
* V4L2: Qualcom camss driver;
* Remote controller: gpio-ir-tx, pwm-ir-tx and zx-irdec drivers.
- The DDbridge DVB driver got a massive update, with makes it in sync
with modern hardware from that vendor;
- There's an important milestone on this series: the DVB
documentation was written in 2003, but only started to be updated
in 2007. It also used to contain several gaps from the time it was
kept out of tree, mentioning error codes and device nodes that
never existed upstream. On this series, it received a massive
update: all non-deprecated digital TV APIs are now in sync with the
current implementation;
- Some DVB APIs that aren't used by any upstream driver got removed;
- Other parts of the media documentation algo got updated, fixing
some bugs on its PDF output and making it compatible with Sphinx
version 1.6.
As the number of hacks required to build PDF output reduced, I hope
we'll have less troubles as newer versions of our documentation
toolchain are released (famous last words);
- As usual, lots of driver cleanups and improvements"
* tag 'media/v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (624 commits)
media: leds: as3645a: add V4L2_FLASH_LED_CLASS dependency
media: get rid of removed DMX_GET_CAPS and DMX_SET_SOURCE leftovers
media: Revert "[media] v4l: async: make v4l2 coexist with devicetree nodes in a dt overlay"
media: staging: atomisp: sh_css_calloc shall return a pointer to the allocated space
media: Revert "[media] lirc_dev: remove superfluous get/put_device() calls"
media: add qcom_camss.rst to v4l-drivers rst file
media: dvb headers: make checkpatch happier
media: dvb uapi: move frontend legacy API to another part of the book
media: pixfmt-srggb12p.rst: better format the table for PDF output
media: docs-rst: media: Don't use \small for V4L2_PIX_FMT_SRGGB10 documentation
media: index.rst: don't write "Contents:" on PDF output
media: pixfmt*.rst: replace a two dots by a comma
media: vidioc-g-fmt.rst: adjust table format
media: vivid.rst: add a blank line to correct ReST format
media: v4l2 uapi book: get rid of driver programming's chapter
media: format.rst: use the right markup for important notes
media: docs-rst: cardlists: change their format to flat-tables
media: em28xx-cardlist.rst: update to reflect last changes
media: v4l2-event.rst: adjust table to fit on PDF output
media: docs: don't show ToC for each part on PDF output
...
This patch adds ALPS PTP sticks with pid/device id 0x120A to the list of
devices supported by hid-multitouch.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On the 2nd generation Lenovo Tablet only clickpad is working; the
trackpoint and three mouse buttons do not work.
hid_multitouch must export all inputs in order to get trackpoint and
buttons to function.
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The MobileStudio Pro, Cintiq Pro, and 2nd-gen Intuos Pro devices use a
different coordinate system for their touchring and pen twist than prior
devices. Prior devices had zero aligned to the tablet's left and would
increase clockwise. Userspace expects data from the kernel to be in this
old coordinate space, so adjustments are necessary.
While the coordinate system for pen twist is formally defined by the HID
standard, no such definition existed for the touchring at the time these
tablets were introduced. Future tablets are expected to report touchring
data using the same "zero-up clockwise-increasing" coordinate system
defined for twist.
Fixes: 50066a042d ("HID: wacom: generic: Add support for height, tilt, and twist usages")
Fixes: 4922cd26f0 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring")
Cc: stable@vger.kernel.org # 4.10, 4.11
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wacom driver's IRQ handler for Bluetooth reports from the 2nd-gen
Intuos Pro does not correctly process negative numbers. Values for
tilt and rotation (which can go negative) are instead interpreted as
unsigned and so jump to very large values when the data should be
negative. This commit properly casts the data to ensure we report
negative numbers when necessary.
Fixes: 4922cd2 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: stable@vger.kernel.org # v4.11
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't populate array cbuf on the stack, instead make it static.
Makes the object code smaller by over 110 bytes:
Before:
text data bss dec hex filename
15096 3504 128 18728 4928 drivers/hid/hid-lg.o
After:
text data bss dec hex filename
14884 3600 128 18612 48b4 drivers/hid/hid-lg.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make this const as it is only passed as an argument to the function
device_create_file and device_remove_file and the corresponding arguments are
of type const. Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some laptops have system-control buttons (e.g. KEY_SLEEP) on the same
interface as a hid-multitouch touch-pad.
This commit fixes these buttons not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Ideacom 6680 touchscreen is found in the Dell Latitude 2100. It
has two USB descriptors, the first of which has two input reports. The
HID_QUIRK_MULTI_INPUT quirk is needed to keep the correct maximum
value for ABS_X/ABS_Y (8191 instead of 65535).
Signed-off-by: Nicholas Bishop <nbishop@neverware.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit a50aac7193 introduces 'led.groups' and adds EKR support
for these groups. However, unlike the other devices with LEDs,
the EKR's LEDs are read-only and we shouldn't attempt to control
them in wacom_led_control().
See bug: https://sourceforge.net/p/linuxwacom/bugs/342/
Fixes: a50aac7193 ("HID: wacom: leds: dynamically allocate LED groups")
Cc: stable <stable@vger.kernel.org> # 4.9
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cintiq 12 has 10 expresskey buttons. The bit shift for the last
two buttons were off by 5.
Fixes: c7f0522 ("HID: wacom: Slim down wacom_intuos_pad processing")
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Matthieu Robin <matthieu@macolu.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- support for media keys on Asus T304UA from João Paulo Rechi Vita
- support for Microsoft Win8 Wireless Radio Controls extensions
from João Paulo Rechi Vita
Conflicts:
drivers/hid/hid-ids.h
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- Arnd pointed out that driver_lock semaphore is superfluous, as
driver core already provides all the necessary concurency protection.
Removal patch from Binoy Jayan
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This snd_rawmidi_ops structure is only passed as the third
argument of snd_rawmidi_set_ops. This argument is const, so the
snd_rawmidi_ops structure can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The power_supply subsystem tends to emit uevent every time
power_supply_changed() is called, so we should call this API only when battery
strength reported by the device is actually different from the previous
readings, otherwise we'll drown the system in uevents.
Fixes: 581c448476 ("HID: input: map digitizer battery usage")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the reference HID sensor hub firmware all Named array enums were
0-based. There is no description of the default base of enums in HID
sensor hub specification as logical minimum should have set this base
value.
Every sensor hub implemented enum as 1-based, without explicitly setting
logical minimum to 1, because of the implementation by one of the major
OS vendor. In Linux we used logical minimum to decide the enum base.
Some sensor hub FWs already changed logical minimum from 0 to 1. We hoped
that every other vendor will follow. But that didn't happen and we had to
fix the report header for every sensor hub to change logical minimum to 1
by using .report_fixup() callback. So for every new sensor hub we had to
modify source code by adding this quirk based on the vendor and device id.
This is becoming a maintenance burden.
This patch hardcodes the logical minimum of power and report state
attributes to 1. In this way we can remove the existing quirks and also
we don't have to add more quirks.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The WACOM_HID_WD_TOUCHRINGSTATUS usage is a single bit which tells us
whether the touchring is currently in use or not. Because we need to
reset the axis value to 0 when the finger is removed, we call
'wacom_map_usage' to ensure that the required type/code values are
associated with the usage. The 'wacom_map_usage' also sets up the axis
range and resolution, however, which is not desired in this particular
case.
Although xf86-input-wacom doesn't do really do anything with the ring's
range or resolution, the libinput driver (for Wayland environments)
uses these values to provide proper angle indications to userspace.
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring")
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Put the touchpad in native (absolute coordinate mode) and export it to
userspace as a touchpad rather then as a mouse.
Note this requires HID_QUIRK_MULTI_INPUT as the T100CHI keyboard dock
has all functionality on a single HID interface and userspace expects
touchpads to be on a separate input_dev. Without MULTI_INPUT userspace
will ignore the keyboard part of the keyboard/touchpad combo.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
0xff310076 application has been defined by 957b8dffa4 ("HID: multitouch:
Support Asus T304UA media keys") as a vendor-specific application with
symbolic constant HID_VD_ASUS_CUSTOM_MEDIA_KEYS, so let's make use of
it.
Fixes: 957b8dffa4 ("HID: multitouch: Support Asus T304UA media keys")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Asus T304UA convertible sports a magnetic detachable keyboard with
touchpad, which is connected over USB. Most of the keyboard hotkeys are
exposed through the same USB interface as the touchpad, defined in the
report descriptor as follows:
0x06, 0x31, 0xFF, // Usage Page (Vendor Defined 0xFF31)
0x09, 0x76, // Usage (0x76)
0xA1, 0x01, // Collection (Application)
0x05, 0xFF, // Usage Page (Reserved 0xFF)
0x85, 0x5A, // Report ID (90)
0x19, 0x00, // Usage Minimum (0x00)
0x2A, 0xFF, 0x00, // Usage Maximum (0xFF)
0x15, 0x00, // Logical Minimum (0)
0x26, 0xFF, 0x00, // Logical Maximum (255)
0x75, 0x08, // Report Size (8)
0x95, 0x0F, // Report Count (15)
0xB1, 0x02, // Feature (Data,Var,Abs,No Wrap,Linear,Preferred State,No Null Position,Non-volatile)
0x05, 0xFF, // Usage Page (Reserved 0xFF)
0x85, 0x5A, // Report ID (90)
0x19, 0x00, // Usage Minimum (0x00)
0x2A, 0xFF, 0x00, // Usage Maximum (0xFF)
0x15, 0x00, // Logical Minimum (0)
0x26, 0xFF, 0x00, // Logical Maximum (255)
0x75, 0x08, // Report Size (8)
0x95, 0x02, // Report Count (2)
0x81, 0x02, // Input (Data,Var,Abs,No Wrap,Linear,Preferred State,No Null Position)
0xC0, // End Collection
This UsagePage is declared as a variable, but we need to treat it as an
array to be able to map each Usage we care about to its corresponding
input key.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some keyboard + touchpad devices have the Microsoft Win8 Wireless Radio
Controls extensions Usage Page define in the touchpad report descriptor,
so we need to support them in this driver.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Manufacturers do not always populate serial number in their devices, so
let's fall back to device ID when forming the battery device name. As a
result, batteries in devices without serial number will be named like
this:
hid-0018:2D1F:510E.0001-battery
(as opposed to hid--battery for the first one, and failing to create
batteries for the subsequent ones).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We already mapped battery strength reports from the generic device
control page, but we did not update capacity from input reports, nor we
mapped the battery strength report from the digitizer page, so let's
implement this now.
Batteries driven by the input reports will now start in "unknown" state,
and will get updated once we receive first report containing battery
strength from the device.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The semaphore 'driver_lock' is used as a simple mutex, and also unnecessary as
suggested by Arnd. Hence removing it, as the concurrency between the probe and
remove is already handled in the driver core.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver has gained a compile-time dependency that we should
express in Kconfig to avoid this link error:
drivers/hid/wacom_sys.o: In function `wacom_parse_and_register':
wacom_sys.c:(.text+0x2eec): undefined reference to `usb_hid_driver'
Fixes: 09dc28acae ("HID: wacom: Improve generic name generation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without a quirk or the X Window System, this device disconnects every
60 seconds. This patch also renames the define associated with the
Logitech 0xc007 product ID, which appeared to have a conflicting typo.
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Kyle Roarty <kroarty@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'wacom_update_name' function is responsible for producing names for
the input device nodes based on the hardware device name. Commit f2209d4
added the ability to strip off prefixes like "Wacom Co.,Ltd." where the
prefix was immediately (and redundantly) followed by "Wacom". The
2nd-generation Intuos Pro 2 has such a prefix, but with a small error
(the period and comma are swapped) that prevents the existing code from
matching it. We're loath to extend the number of cases out endlessly and
so instead try to be smarter about name generation.
We observe that the cause of the redundant prefixes is HID combining the
manufacturer and product strings of USB devices together. By using the
original product name (with "Wacom" prefixed, if it does not already
exist in the string) we can bypass the gyrations to find and remove
redundant prefixes. Other devices either don't have a manufacturer string
that needs to be removed (Bluetooth, uhid) or should have their name
generated from scratch (I2C).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Although HID itself is transport-agnostic, occasionally a driver may
want to interact with the low-level transport that a device is connected
through. To do this, we need to know what kind of bus is in use. The
first guess may be to look at the 'bus' field of the 'struct hid_device',
but this field may be emulated in some cases (e.g. uhid).
More ideally, we can check which ll_driver a device is using. This
function introduces a 'hid_is_using_ll_driver' function and makes the
'struct hid_ll_driver' of the four most common transports accessible
through hid.h.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The iHome keypad also requires the same tweak we are doing for other
Ortek devices.
Reported-by: Mairin Duffy <duffy@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Even though the IO for devices with "always poll" quirk is already running,
we still need to set HID_OPENED bit in usbhid->iofl so the interrupt
handler does not ignore the data coming from the device.
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Olof Johansson <olof@lixom.net>
Fixes: e399396a6b ("HID: usbhid: remove custom locking from usbhid_open...")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Asus Transformer T100CHI comes with a Bluetooth keyboard dock which
uses the same 0xff31 Asus vendor HUT page as other Asus keyboards.
This commit adds its device-id to hid-asus and fixes an issue in the
descriptor of the 0xff31 Usage, which together fixes the special keys
on this keyboard not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The touchpad code is only used with the T100TA touchpad which
measures 75.5 x 41.5 mm, add corresponding resolution info.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When adding the initial support I only looked at the maximum coordinates
but the Y axis is inverted, so I should have checked the minimum
coodinates which never reach 0 due to max_y being wrong, fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of having hardcoded (#define-d) values use a struct describing
the various touchpad parameters. This is a preparation patch for
improving the T100TA touchpad support as well as for adding T100CHI
touchpad support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the Asus T100 touchpad in multi-touch mode (rather
then mouse emulation mode). It turns out that the Asus T100 touchpad
is identical to the already supported i2c-hid Asus touchpads, so
adding support for it was easy.
The only significant difference is that the reported x-coordinates
range on the T100 touchpad is somewhat lower then the range on the
already supported touchpads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Check return value from call to devm_kmemdup() in order to prevent a NULL
pointer dereference.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Variable mode in method wacom_show_remote_mode() is defined as u8, thus
statement (mode >= 0) is always true and should be removed, simplifying
the logic.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that input core insists on having dev->absinfo when device claims to
generate EV_ABS in its dev->evbit, we should not be blindly setting that
bit.
The code in question might have been needed before input_set_abs_params()
started setting EV_ABS in device's evbit, but not anymore, and is now
breaking devices such as SMART SPNL-6075 Touchscreen.
Fixes: 6ecfe51b40 ("Input: refuse to register absolute devices ...")
Reported-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- open/close tracking improvements from Dmitry Torokhov
- battery support improvements in Wacom driver from Jason Gerecke
- Win8 support fixes from Benjamin Tissories and Hans de Geode
- misc fixes to Intel-ISH driver from Arnd Bergmann
- support for quite a few new devices and small assorted fixes here and
there
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (35 commits)
HID: intel-ish-hid: Enable Gemini Lake ish driver
HID: intel-ish-hid: Enable Cannon Lake ish driver
HID: wacom: fix mistake in printk
HID: multitouch: optimize the sticky fingers timer
HID: multitouch: fix rare Win 8 cases when the touch up event gets missing
HID: multitouch: use BIT macro
HID: Add driver for Retrode2 joypad adapter
HID: multitouch: Add support for Google Rose Touchpad
HID: multitouch: Support PTP Stick and Touchpad device
HID: core: don't use negative operands when shift
HID: apple: Use country code to detect ISO keyboards
HID: remove no longer used hid->open field
greybus: hid: remove custom locking from gb_hid_open/close
HID: usbhid: remove custom locking from usbhid_open/close
HID: i2c-hid: remove custom locking from i2c_hid_open/close
HID: serialize hid_hw_open and hid_hw_close
HID: usbhid: do not rely on hid->open when deciding to do IO
HID: hiddev: use hid_hw_power instead of usbhid_get/put_power
HID: hiddev: use hid_hw_open/close instead of usbhid_open/close
HID: asus: Add support for Zen AiO MD-5110 keyboard
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
- introduce the new uuid_t/guid_t types that are going to replace
the somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS
and libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)
-----BEGIN PGP SIGNATURE-----
iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAllZfmILHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYMvyg/9EvWHOOsSdeDykCK3KdH2uIqnxwpl+m7ljccaGJIc
MmaH0KnsP9p/Cuw5hESh2tYlmCYN7pmYziNXpf/LRS65/HpEYbs4oMqo8UQsN0UM
2IXHfXY0HnCoG5OixH8RNbFTkxuGphsTY8meaiDr6aAmqChDQI2yGgQLo3WM2/Qe
R9N1KoBWH/bqY6dHv+urlFwtsREm2fBH+8ovVma3TO73uZCzJGLJBWy3anmZN+08
uYfdbLSyRN0T8rqemVdzsZ2SrpHYkIsYGUZV43F581vp8e/3OKMoMxpWRRd9fEsa
MXmoaHcLJoBsyVSFR9lcx3axKrhAgBPZljASbbA0h49JneWXrzghnKBQZG2SnEdA
ktHQ2sE4Yb5TZSvvWEKMQa3kXhEfIbTwgvbHpcDr5BUZX8WvEw2Zq8e7+Mi4+KJw
QkvFC1S96tRYO2bxdJX638uSesGUhSidb+hJ/edaOCB/GK+sLhUdDTJgwDpUGmyA
xVXTF51ramRS2vhlbzN79x9g33igIoNnG4/PV0FPvpCTSqxkHmPc5mK6Vals1lqt
cW6XfUjSQECq5nmTBtYDTbA/T+8HhBgSQnrrvmferjJzZUFGr/7MXl+Evz2x4CjX
OBQoAMu241w6Vp3zoXqxzv+muZ/NLar52M/zbi9TUjE0GvvRNkHvgCC4NmpIlWYJ
Sxg=
=J/4P
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid
Pull uuid subsystem from Christoph Hellwig:
"This is the new uuid subsystem, in which Amir, Andy and I have started
consolidating our uuid/guid helpers and improving the types used for
them. Note that various other subsystems have pulled in this tree, so
I'd like it to go in early.
UUID/GUID summary:
- introduce the new uuid_t/guid_t types that are going to replace the
somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS and
libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)"
* tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid: (34 commits)
ACPI: hns_dsaf_acpi_dsm_guid can be static
mmc: sdhci-pci: make guid intel_dsm_guid static
uuid: Take const on input of uuid_is_null() and guid_is_null()
thermal: int340x_thermal: fix compile after the UUID API switch
thermal: int340x_thermal: Switch to use new generic UUID API
acpi: always include uuid.h
ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
ACPI / extlog: Switch to use new generic UUID API
ACPI / bus: Switch to use new generic UUID API
ACPI / APEI: Switch to use new generic UUID API
acpi, nfit: Switch to use new generic UUID API
MAINTAINERS: add uuid entry
tmpfs: generate random sb->s_uuid
scsi_debug: switch to uuid_t
nvme: switch to uuid_t
sysctl: switch to use uuid_t
partitions/ldm: switch to use uuid_t
overlayfs: use uuid_t instead of uuid_be
fs: switch ->s_uuid to uuid_t
ima/policy: switch to use uuid_t
...
Added PCI ID for Gemini Lake ISH.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added PCI ID for Cannon Lake ISH.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
trivial fix to spelling mistake in hid_warn warning message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of unconditionally expiring the timer and calling a long
mt_release_contacts(), we can check if some slots are used when the
timer expires.
We can also remove the timer if we happen to receive all the releases.
The logic behind the MT_IO_FLAGS_PENDING_SLOTS could be implemented by
counting how many slots are active, but using bits feels slightly more
efficient.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of blindly trusting the hardware to send us release, we should
consider some events can get lost and release them when we judge time has
come.
The Windows 8 spec allows to be confident in the fact that the device
will continuously report events when a finger touches the surface.
This has been tested on the HID recording database I have, and all of
those devices behave properly.
Also, Arek tested it on his Lenovo Yoga 910, which exports such bug in
some situations, when the movements are rather slow.
We use an atomic bit here to guard against concurrent accesses to the mt
slots because both mt_process_mt_event() and mt_expired_timeout() are
called in interrupt context.
Signed-off-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(1 << X) is wrong. We should use BIT(X)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver does 2 things:
- Apply the MULTI_INPUT quirk to create separate joypad device nodes
for each one of the 4 connectors.
- Rename the input devices so that their names are different, and allow
users to recognise which device corresponds to which physical port,
including the SNES (Mario Paint) Mouse.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Google Rose Touchpad USB PID and required quirks.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Support PTP Stick and Touchpad device. This Touchpad is Precision Touchpad
(PTP), and Stick Pointer data is the same as Mouse; Stick Pointer works as
Mouse.
[jkosina@suse.cz: changelog deuglification]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Setting these bits causes libinput to fail to initialize the device;
setting BTN_TOUCH and BTN_TOOL_FINGER causes it to treat the mouse as a
touchpad, and it then refuses to continue when it discovers ABS_X is not
set.
This breaks all known Wayland compositors, as well as Xorg when the
libinput driver is being used.
This reverts commit f4b65b9563.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Che-Liang Chiou <clchiou@chromium.org>
Cc: Thierry Escande <thierry.escande@collabora.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are many situations where generic HID driver provides some basic level
of support for certain device, but later this support (usually by implementing
vendor-specific extensions of HID protocol) is extended and the support moved
over to a separate (usually per-vendor) specific driver.
This might bring a rather unpleasant suprise for users, as all of a sudden
there is a new config option they have to enable in order to get any support
for their device whatsoever, although previous kernel versions provided basic
support through the generic driver. Which is rightfully seen as a regression.
Fix this by including the entry for a particular device in
hid_have_special_driver[] iff the specific config option has been specified,
and let generic driver handle the device otherwise.
Also make the behavior of hid_scan_report() (where the same decision is being
taken on a per-report level) consistent.
While at it, reshuffle the hid_have_special_driver[] a bit to restore the
alphabetical ordering (first order by config option, and within those
sections order by VID).
This is considered a short-term solution, before generic way of giving
precedence to special drivers and falling back to generic driver is
figured out.
While at it, fixup a missing entry for GFRM driver; thanks to Hans de Geode for
spotting this (and for discovering a few issues in the conversion).
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The recent C standard in 6.5.7 paragraph 4 defines that operands for
bitwise shift operators should be non-negative, otherwise it's an
undefined behaviour.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the quest to get rid of DRIVER_ATTR(), this patch converts the
hid-core code to use DRIVER_ATTR_RO() and also moves to use drv_groups
as creating individual sysfs files is not good (it races with userspace
notifications.)
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <linux-input@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_attrs field has long been "depreciated" and is finally being
removed, so move the driver to use the "correct" dev_groups field
instead for struct bus_type.
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Wei Yongjun <weiyj.lk@gmail.com>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: <linux-input@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least on newer laptops, Apple uses the same USB ID for both ISO and
ANSI keyboards. However, they have been good about filling in the
bCountryCode field in the HID descriptor on all of their keyboards. A
value of 13 indicates an ISO layout and other values indicate various
country-specific ANSI layouts.
With this patch, users of Apple US keyboards will no longer have to run
`echo 0 > /sys/module/hid_apple/parameters/iso_layout` to get a working
tilde key.
Please test this patch and send feedback if you have a Macbook or an
Apple keyboard.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that HID core enforces serialization of transport driver open/close
calls we can remove custom locking from usbhid driver.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that HID core enforces serialization of transport driver open/close
calls we can remove custom locking from i2c-hid driver.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID transport drivers either re-implement exactly the same logic
(usbhid, i2c-hid) or forget to implement it (usbhid) which causes issues
when the same device is accessed via multiple interfaces (for example input
device through evdev and also hidraw). Let's muve the locking logic into
HID core to make sure the serialized behavior is always enforced.
Also let's uninline and move hid_hw_start() and hid_hw_stop() into hid-core
as hid_hw_start() is somewhat large and do not believe we get any benefit
from these two being inline.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of checking hid->open (that we plan on having HID core manage) in
hid_start_in(), let's allocate a couple of new flags: HID_IN_POLLING and
HID_OPENED, and use them to decide whether we should be submitting URBs or
not.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of calling into usbhid code directly, let's use the standard
accessors for the transport HID drivers, and stop clobbering their error
codes with -EIO.
This also allows us to remove usbhid_get/put_power(), leaving only
usbhid_power().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of calling into usbhid code directly, let's use the standard
accessors for the transport HID drivers, and stop clobbering their errors
with -EIO.
This also allows us make usbhid_open and close static.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for media keys on the MD-5110 wireless keyboard that comes
with the Asus V221ID and ZN241IC All In One computers.
The keys to support here are WLAN, BRIGHTNESSDOWN and BRIGHTNESSUP.
The USB Vendor ID suggests that it is a TURBOX device, but
the physical branding only mentions ASUS MD-5110.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Benjamin Tissoires <benajmin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Asus AIO keyboard AK1D was added to hid-chicony based on its
USB vendor ID, however images available online suggest that this keyboard
is physically branded as ASUS with no mention of Chicony.
A recent commit also added support for another Asus AIO keyboard into
hid-chicony, this one with USB vendor ID Jess, and a pending review
comment asked me to move it into hid-asus because it is also only
physically branded as ASUS.
I updated the USB ID defines to match the branding and product name,
including noting that the recently added keyboard is labelled as
ASUS MD-5112.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Benjamin Tissoires <benajmin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This mouse is also known under other IDs. It needs the quirk
ALWAYS_POLL or will disconnect in runlevel 1 or 3.
Signed-off-by: Sebastian Parschauer <sparschauer@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- corner-case oops fixes for Asus and Wacom drivers from Carlo Caione
and Jason Gerecke
- power management fix (reported on SIS0817 touchscreen) for i2c-hid
devices from Hans de Goede
- device-id-specific fixes and quirks from Hans de Goede, Diego Elio
Pettenò and Che-Liang Chiou
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: asus: Stop underlying hardware on remove
HID: i2c: Call acpi_device_fix_up_power for ACPI-enumerated devices
HID: asus: Add support for T100 keyboard
HID: elecom: extend to fix the descriptor for DEFT trackballs
HID: magicmouse: Set multi-touch keybits for Magic Mouse
HID: wacom: Have wacom_tpc_irq guard against possible NULL dereference
We are missing a call to hid_hw_stop() on the remove hook.
Among other things this is causing an Oops when (re-)starting GNOME /
upowerd / ... after the module has been already rmmod-ed.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To increase build coverage, drivers should generally be allowed to
build on other architectures even if they are only used on one
of them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When building for 32-bit architectures, we get a harmless warning:
intel-ish-hid/ishtp-hid-client.c: In function 'process_recv':
intel-ish-hid/ishtp-hid-client.c:139:7: error: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'unsigned int' [-Werror=format=]
This changes the format string to print size_t variables using %zu
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The internal accounting uses 'timespec' based time stamps, which is
slightly inefficient and also problematic once we get to the time_t
overflow in 2038.
When communicating to the firmware, we even get an open-coded 64-bit
division that prevents the code from being build-tested on 32-bit
architectures and is inefficient due to the double conversion from
64-bit nanoseconds to seconds+nanoseconds and then microseconds.
This changes the code to use ktime_t instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I was trying to understand this code while working on a warning
fix and the locking made no sense: spin_lock_irqsave() is pointless
when run inside of an interrupt handler or nested inside of another
spin_lock_irq() or spin_lock_irqsave().
Here it turned out that the comment above the function is wrong,
as both recv_ishtp_cl_msg_dma() and recv_ishtp_cl_msg() can in fact
be called from a work queue rather than an ISR, so we do have to
use the irqsave() version once.
This fixes the comments accordingly, removes the misleading 'dev_flags'
variable and modifies the inner spinlock to not use 'irqsave'.
No functional change is intended, this is just for readability and
it slightly simplifies the object code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
gcc points out an uninialized pointer dereference that could happen
if we ever get to recv_ishtp_cl_msg_dma() or recv_ishtp_cl_msg()
with an empty &dev->read_list:
drivers/hid/intel-ish-hid/ishtp/client.c: In function 'recv_ishtp_cl_msg_dma':
drivers/hid/intel-ish-hid/ishtp/client.c:1049:3: error: 'cl' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The warning only appeared in very few randconfig builds, as the
spinlocks tend to prevent gcc from tracing the variables. I only
saw it in configurations that had neither SMP nor LOCKDEP enabled.
As we can see, we only enter the case if 'complete_rb' is non-NULL,
and then 'cl' is known to point to complete_rb->cl. Adding another
initialization to the same pointer is harmless here and makes it
clear to the compiler that the behavior is well-defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For ACPI devices which do not have a _PSC method, the ACPI subsys cannot
query their initial state at boot, so these devices are assumed to have
been put in D0 by the BIOS, but for touchscreens that is not always true.
This commit adds a call to acpi_device_fix_up_power to explicitly put
devices without a _PSC method into D0 state (for devices with a _PSC
method it is a nop). Note we only need to do this on probe, after a
resume the ACPI subsys knows the device is in D3 and will properly
put it in D0.
This fixes the SIS0817 i2c-hid touchscreen on a Peaq C1010 2-in-1
device failing to probe with a "hid_descr_cmd failed" error.
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use a better URL for the HUTRR40 Radio HID Usages documentation and use the
HID_GD_WIRELESS_RADIO_CTLS define rather then hardcoding a check for
0x0001000c.
Fixes: 61df56bef9 ("HID: Add mapping for Microsoft Win8 Wireless Radio Controls extensions")
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The keyboard dock used with the Asus Transformer T100 series, uses
the same vendor-defined 0xff31 usage-page as some other Asus
keyboards. But with a small twist, it has a small descriptor bug which
needs to be fixed up for things to work.
This commit adds the USB-ID for this keyboard to the hid-asus driver
and makes asus_report_fixup fix the descriptor issue, fixing
various special function keys on this keyboard not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ELECOM DEFT trackballs report only five buttons, when the device
actually has 8. Change the descriptor so that the HID driver can see all of
them.
For completeness and future reference, I included a side-by-side diff of
the part of the descriptor that is being edited.
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Yuxuan Shui <yshuiv7@gmail.com>
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ITE8595 keyboard uses the HID_GD_RFKILL_BTN usage code
from the Wireless Radio Controls Application Collection Microsoft
has defined for Windows 8 and later.
However it has a quirk, when the rfkill hotkey is pressed it does
generate a report for the collection, but the reported value is
always 0. Luckily it is the only button in this collection / report,
and it sends a report on release only, so receiving a report means the
button was pressed.
This commit adds a hid-ite driver which watches for the Wireless Radio
Controls Application Collection report and then reports a KEY_RFKILL event,
ignoring the value, making the rfkill on this keyboard work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft has defined some extra HUT codes for the Generic Desktop Page
for Wireless Radio controls, see:
https://docs.microsoft.com/en-us/windows-hardware/drivers/hid/airplane-mode-radio-managementhttps://web.archive.org/web/20170509144631/https://docs.microsoft.com/en-us/windows-hardware/drivers/hid/airplane-mode-radio-management
I've 3 2-in-1 keyboard docks: Dell Venue Pro 11 keyboard dock,
HP pavilion x2 keyboard dock and a PEAQ C1010 keyboard dock which have
a wireless radio toggle hotkey, which uses the 0x000100c6 HUT code
defined in these extensions.
This commit adds a mapping for this key, this makes the rfkill toggle
hotkey work on the Dell Venue Pro 11 and HP Pavilion X2 keyboards,
the PEAQ C1010 keyboard does generate events for the 0x000100c6 HUT
code when pressed, but the reported value is always 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Generic battery handling code is spread between the pen and pad codepaths
since battery usages may appear in reports for either. This makes it
difficult to concisely see the logic involved. Since battery data is
not treated like other data (i.e., we report it through the power_supply
subsystem rather than through the input subsystem), it makes reasonable
sense to split the functionality out into its own functions.
This commit has the generic battery handling duplicate the same pattern
that is used by the pen, pad, and touch interfaces. A "mapping" function
is provided to set up the battery, an "event" function is provided to
update the battery data, and a "report" function is provided to notify
the power_supply subsystem after all the data has been read. We look at
the usage itself rather than its collection to determine if one of the
battery functions should handle it. Additionally, we unconditionally
call the "report" function since there is no particularly good way to
know if a report contained a battery usage; 'wacom_notify_battery()'
will filter out any duplicate updates, however.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
At the moment, our driver relies on 'wacom_battery_get_property()' to
determine the most likely battery state (e.g charging, discharging, or
full) based on the information available. It is not always possible
for the function to properly determine this, however. For instance,
whenever an AES pen leaves proximity the battery state becomes
indeterminite. This commit adds the ability to provide it with explict
state information if desired. Whenever explicit state is not required
(the majority of circumstances), WACOM_POWER_SUPPLY_STATUS_AUTO can
be used in its place.
Three uses of explicit battery status are added: two wireless disconnect
paths and the AES case mentioned above.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When support for the HID_DG_BATTERYSTRENGTH usage was added for AES devices,
it appears that the value was read, but never actually forwarded to the
power_supply subystem for userspace's benefit. Let's correct that.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
AES sensors use the value 0 to indicate "not available" rather than
"completely dead". Such values are often sent for dozens of reports
while the pen is being brought into proximity and can cause userspace
to get the wrong impression about the actual battery state.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The power_supply subsystem expects us to provide it with capacity values
measured in percent. In particular, AES devices (HID_DG_BATTERYSTRENGTH)
use the range 0-255, which needs to be rescaled. The MobileStudio Pro
(WACOM_HID_WD_BATTERY_LEVEL) uses the range 0-100, but there's no guarantee
that future devices will share the same range.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver emits multi-touch events for Magic Trackpad as well as Magic
Mouse, but it does not set keybits that are related to multi-touch event
for Magic Mouse; so set these keybits.
The keybits that are not set cause trouble because user programs often
probe these keybits for self-configuration and thus they cannot operate
properly if the keybits are not set.
One of such troubles is that libevdev will not be able to emit correct
touch count, causing gestures library failed to do fling stop.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The following Smatch complaint was generated in response to commit
2a6cdbd ("HID: wacom: Introduce new 'touch_input' device"):
drivers/hid/wacom_wac.c:1586 wacom_tpc_irq()
error: we previously assumed 'wacom->touch_input' could be null (see line 1577)
The 'touch_input' and 'pen_input' variables point to the 'struct input_dev'
used for relaying touch and pen events to userspace, respectively. If a
device does not have a touch interface or pen interface, the associated
input variable is NULL. The 'wacom_tpc_irq()' function is responsible for
forwarding input reports to a more-specific IRQ handler function. An
unknown report could theoretically be mistaken as e.g. a touch report
on a device which does not have a touch interface. This can be prevented
by only calling the pen/touch functions are called when the pen/touch
pointers are valid.
Fixes: 2a6cdbd ("HID: wacom: Introduce new 'touch_input' device")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Like other switches, the Aten CS-1758 KVM switch needs a quirk to avoid
spewing errors:
[12599018.071059] usb 5-2: input irq status -75 received
[12599018.079053] usb 5-2: input irq status -75 received
Signed-off-by: Vasilis Liaskovitis <vliaskovitis@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It apears that devices designed around Wacom's G11 chipset (e.g. Lenovo
ThinkPad Yoga 260, Lenovo ThinkPad X1 Yoga, Dell XPS 12 9250, Dell Venue
8 Pro 5855, etc.) suffer from a common issue in their HID descriptors.
The logical maximum is not updated for the "Contact Identifier" usage,
leaving it as just "1" despite these devices being capable of tracking
far more touches.
Commit 60a2218698 began ignoring usages with out-of-range values,
causing problems for devices based on this chipset. Touches after
the first will have an out-of-range Contact Identifier, and ignoring
that usage will cause the kernel to incorrectly slot each finger's
events (along with all the knock-on userspace effects that entails).
This commit checks for these buggy descriptors and updates the maximum
where required. Prior chipsets have used "255" as the maximum (and the
G11, at least, doesn't seem to actually use IDs outside the range of
1..CONTACTMAX) so continue using this value.
Cc: stable@vger.kernel.org
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Because HID_DG_TOOLSERIALNUMBER doesn't first cast the value recieved from HID
to an unsigned type, sign-extension rules can cause the value of
wacom_wac->serial[0] to inadvertently wind up with all 32 of its highest bits
set if the highest bit of "value" was set.
This can cause problems for Tablet PC devices which use AES sensors and the
xf86-input-wacom userspace driver. It is not uncommon for AES sensors to send a
serial number of '0' while the pen is entering or leaving proximity. The
xf86-input-wacom driver ignores events with a serial number of '0' since it
cannot match them up to an in-use tool. To ensure the xf86-input-wacom driver
does not ignore the final out-of-proximity event, the kernel does not send
MSC_SERIAL events when the value of wacom_wac->serial[0] is '0'. If the highest
bit of HID_DG_TOOLSERIALNUMBER is set by an in-prox pen which later leaves
proximity and sends a '0' for HID_DG_TOOLSERIALNUMBER, then only the lowest 32
bits of wacom_wac->serial[0] are actually cleared, causing the kernel to send
an MSC_SERIAL event. Since the 'input_event' function takes an 'int' as
argument, only those lowest (now-cleared) 32 bits of wacom_wac->serial[0] are
sent to userspace, causing xf86-input-wacom to ignore the event. If the event
was the final out-of-prox event, then xf86-input-wacom may remain in a state
where it believes the pen is in proximity and refuses to allow other devices
under its control (e.g. the touchscreen) to move the cursor.
It should be noted that EMR devices and devices which use both the
HID_DG_TOOLSERIALNUMBER and WACOM_HID_WD_SERIALHI usages (in that order) would
be immune to this issue. It appears only AES devices are affected.
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The latest USB keyboards shipped on several ASUS laptop models
(including ROG laptop models such as GL702VMK) have the keyboards
backlight controlled by the keyboard firmware.
The firmware implements at least 3 different commands:
- Init command (to use when the system starts)
- Configuration command (to get keyboard status/information)
- Backlight level control (to change the level of the keyboard light)
With this patch we create the usual 'asus::kbd_backlight' led class
entry to control the keyboard backlight.
[jkosina@suse.cz: remove pointless cancel_work_sync() call while
handling an error in asus_kbd_register_leds(), as spotted by
Benjamin]
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These two functions awkwardly break up the otherwise-contiguous chunk of
related Intuos IRQ functions with a 500 line tangent about the operation
of the EKR. Their presence makes it difficult to read/navigate through the
the Intuos code. Since there is no dependency between these functions, it
is possible to simply move them down somewhat. This commit moves them
to be after the final Intuos IRQ function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commits d793ff8 and 4082da8 introduced two pad usages which do not
actually send pad input events. To make sure we do not post empty
pad packets, pad_input_event_flag is introduced. Turn on the flag
for real pad input events so we can synchronize them properly.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device has a different vendor id but responds to initialization.
Signed-off-by: Xiaolei Yu <dreifachstein@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
err is being checked for failure each time it is being updated
so this err check is totally redundant and can be removed
Detected with CoverityScan, CID#1420665 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make sure we sure register any sensor when sony_input_configured failes.
Somehow this line got lost during resolving of merge conflicts in the
motion sensor patch series and a redudant remove was added as well later
on.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By default when using bluetooth the DS4 reports data at about 1kHz,
which is quite fast especially on weak devices. We now make the
device use the USB poll interval, which is a fixed 4ms. In addition
we make the value adjustable through sysfs.
The error handling in sony_input_configured is a little tricky. It
is not easy to add other goto's as not all codepaths have logic
for adding this attribute. Luckily we are setting the value for the
attribute to a default value, so we can use that to detect if we need
to remove the file.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only set bit flags for the portions of the DS4 output report
for which we have data.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These colors are more the default colors normally used on the DS4.
The previous ones were faint and not so noticeable.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The navigation controller is a DS3 (sixaxis) with fewer physical
axes and buttons. It utilizes the same HID report as the DS3 and
thus reports axes/buttons which aren't physically present.
Currently many non-existing buttons and axes are reported, which
we are now removing.
For the axes/buttons which do exist, we make the axis/button mapping
similar to the DS3.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DS3 MAC address is reported as a unique identified when
using Bluetooth. For USB there is no unique identifier reported
yet, so use the MAC address.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This way, upower can add a simple udev rule to decide whether or not
it should use the internal unifying support or just the generic kernel
one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Solar Keyboard uses a different feature to report the battery level.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CAPACITY LEVEL allows to forward rough information on the battery mileage.
HID++ 2.0 devices will either report percentage or levels, so better
forwarding this information to the user space.
The M325 supports only 2 levels: 'Full' and 'Critical'. With mileage,
it will report either 90% or 5%, which might confuse users. With this
change the battery will either report "Full" or "Critical".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The power_supply term for the percentage is capacity. Capacity level
can be given when non accurate mileage is provided by the device, so
better stick to the terms used in power_supply.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When ONLINE isn't set, upower should ignore the battery capacity,
so there is no need to overload it with some random values.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a device reconnects, there is a high chance its power supply has
been changed (for a battery replacement for instance). Just forward
the battery state here.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Or the device just answers a valid feature '0'.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The creation of the power_supply should not be in a HID++ 2.0 specific
function.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Better forwarding the device name, manufacturer and serial to upower.
Note that serial is still empty, it will be filled in a later patch
in this series.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery events are reported through HID++, so we need to be sure
the report ID is the HID++ one.
Without this, we might receive keyboard events that looks just like
battery events with wrong data and which will confuse user space.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like all users don't care about a disconnect.
Simplify the various variant_connect() and put the connect state check
at the beginning.
For delayed input devices, make sure we go through all other connect
values (protocol, battery) before bailing out.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidpp->name can't be null.
Only HID++ 2.0 and above device supports the query.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unifying devices are different from others because they can probed
while not connected. So we need to talk to the receiver to get some
extra information like the device name and the serial.
Instead of having conditionals while attempting to read the device name
from HID++ 2.0, have a special init path for them.
Store the retrieved serial in hdev->uniq.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Do not pollute the quirks bits field which is public API
with elements that are queried from the device.
Move the 2 battery capabilities into the new field.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unless they are connected through unifying, they don't support it,
so remove one error in the logs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without a scope defined, UPower assumes that the battery provides
power to the computer it's connected to, like a laptop battery or a UPS.
Tested-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Register 0xB5 should be handled specially no matter what function is
used. This allows to retrieve the serial and the Quad ID from
hid-logitech-hidpp directly.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 3b164a00a9 ("HID: wacom: Cleanup unsupported device_type
for BAMBOO_PT") cleaned up Bamboo devices which our driver falsely
claimed had touch. Bamboo One Medium also does not have touch.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit a544c619a5 ("HID: wacom: do not attempt to switch mode
while in probe") introduces delayed work for querying (setting the
mode) on all tablets. Bamboo Touch (056a:00d0) has a ghost
interface which claims to be a pen device. Though this device can
be removed, we have to set the mode on the ghost pen interface
before we remove it. After the aforementioned delay was introduced
the device was being removed before the mode setting could be
executed.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A previous commit (below) adds a check for already probed interfaces to
Wacom's matching heuristic. Unfortunately this causes the Bamboo Pen
(CTL-460) to match itself to its 'ghost' touch interface. After
subsequent changes to the driver this match to the ghost causes the
kernel to crash. This patch avoids calling wacom_add_shared_data()
for the BAMBOO_PEN's ghost touch interface.
Fixes: 41372d5d40 ("HID: wacom: Augment 'oVid' and 'oPid' with heuristics for HID_GENERIC")
Cc: stable <stable@vger.kernel.org> # 4.9
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The input mapping code incorrectly maps the Airplane Mode button to
KEY_WLAN, which stands for WiFi toggle, but doesn't affect Bluetooth
(and other active radios) which is expected behavior for Airplane
Mode.
The fix replaces KEY_WLAN with the more appropriate KEY_RFKILL.
The declared usage code 0x88 corresponds to Airplane Mode button on
all keyboards handled by hid-asus (I2C netbook keyboards and USB
RoG series keyboards), so the fix doesn't introduce any
inconsistencies across different models.
Signed-off-by: Matjaz Hegedic <matjaz.hegedic@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Keyboards handled by hid-asus declare special key functions
using a vendor-specific page, however, alongside legitimate
key functions, dummy usages with seemingly arbitrary values
are also declared and can lead to keyboards being detected
as pointer devices by some software (such as X.org).
In addition, for the I2C keyboard volume controls are
separately declared in a Consumer Usage page, with the same
dummy usage problem.
The fix in 1989dada7c ("HID: input: ignore System Control
application usages if not System Controls") does not mitigate
the problem described above, therefore dummy usages need to
be ignored in the driver itself.
This fix properly ignores dummy usages and introduces a quirk
for custom handling of the Consumer Usages on the I2C keyboard.
Signed-off-by: Matjaz Hegedic <matjaz.hegedic@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Before commits a1cbda7a65a7a ("HID: asus: drop dependency
on I2C_HID") and 64a403c6555fd ("HID: asus: support Republic
Of Gamers special keys") hid-asus only pertained to a single
I2C keyboard model found in ASUS X205TA, F205TA, & X200HA. The
aforementioned commits expanded this support to other ASUS
laptop keyboard models.
In order to clarify that existing keyboard and touchpad quirks
only apply to the I2C devices, and not ASUS keyboards in
general, I2C HID IDs and their corresponding quirk sets have
been renamed. In addition, the latter commit introduced
special key handling, which also applies to the I2C keyboard,
not just Republic of Gamers series. Therefore, the
rog_map_key_clear() macro is renamed to asus_map_key_clear()
for the sake of generality.
Signed-off-by: Matjaz Hegedic <matjaz.hegedic@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the special keys found on the internal keyboard of the
Asus Republic of Gamers (ROG) laptop models GL553VD, GL553VE, GL753VD
and GL753VE.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is nothing transport-specific in this driver, and we will now be
adding support for some Asus USB devices too.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
They are part of HUTRR34 for multi-touch digitizers:
0x0E Device configuration CA 16.7
0x23 Device settings CL 16.7
Signed-off-by: Xiaolei Yu <dreifachstein@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a new clone of the XIN MO arcade controller which has same issue with
out of range like the original. This fix will solve the issue where 2
directions on the joystick are not recognized by the new THT 2P arcade
controller with device ID 0x75e1. In details the new device ID is added the
hid-id list and the hid-xinmo source code.
Signed-off-by: Peter Stein <peter@stuntstein.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- regression fixes for Wacom devices, from Aaron Armstrong Skomra and
Ping Cheng
- memory leak in hid-sony driver from Roderick Colenbrander
- new device IDs support from Oscar Campos and Daniel Drake
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: generic: Wacom mouse is only provided for opaque tablets
HID: corsair: Add driver Scimitar Pro RGB gaming mouse 1b1c:1b3e support to hid-corsair
HID: corsair: support for K65-K70 Rapidfire and Scimitar Pro RGB
HID: wacom: don't manually release resources for the EKR
HID: wacom: Correct Intuos Pro 2 resolution
HID: sony: Fix input device leak when connecting a DS4 twice using USB/BT
HID: chicony: Add support for another ASUS Zen AiO keyboard
GPIOLIB_IRQCHIP is not visible to user, so we can't depend on it.
Depend on GPIOLIB but select GPIOLIB_IRQCHIP.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need to store the minor number each drivers. In case of hidraw, the
minor number is stored stores in struct hidraw. But hiddev's minor is
located in struct hid_device.
The hid-core driver announces a kernel message which driver is loaded when
HID device connected, but hiddev's minor number is always zero. To proper
display hiddev's minor number, we need to store the minor number asked from
usb core and do some refactoring work (move from hiddev.c to hiddev.h) to
access hiddev in hid-core.
[jkosina@suse.cz: rebase on top of newer codebase]
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The cp2112 driver is working on hidraw not hiddev. So we need to use proper
hidraw name with hidraw's minor number.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Game controllers can be connected twice through USB and BT. Only
one connection is allowed. Currently we perform a check for duplicate
controllers halfway through device initialization. To prevent
'transient' devices, we should do this check as early as we can.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds a separate evdev node for the DS3 its motion
sensors. We only expose the accelerometers as the gyroscope
is extremely difficult to manage and behavior varies a lot
between hardware revisions.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds printing when we failed to activate DS3 / Nagivation
controllers and checks the return value for these failures earlier
in sony_input_configured. This paves the way for other configuration
logic for these devices, which we don't want to call if for example
the activation failed.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The axis and button mapping for the DS3 is strange. This is mostly
due to the device reporting many axes as for every digital button
it also has an analog button. Due to amount of analog values it
is even leaking well into the MT axes range.
We felt it is best to remove the many analog buttons and just report
digital and comply to the Linux gamepad spec. The analog buttons are
rarely used on the official platform, let alone on Linux.
This patch does remove motion sensor support (added back in another
patch).
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently the DS4 touchpad device is neither classified as a direct
input device nor as a pointer device. It makes most sense to mark
it as a pointer device.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DualShock 4 dongle isn't connected to a real DualShock 4 at
time of driver loading. When a DualShock 4 is plugged in, we
need to obtain calibration data (the dongle would have zeros).
This patch adds calibration logic, which we schedule on a hotplug
from sony_raw_event. In addition this patch adds dongle state
handling.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver currently uses sony_schedule_work to submit output
reports for the different devices for LEDs or rumble.
This patch adds a new parameter to sony_schedule_work to allow
scheduling for other types of work. The next patch in this series
will utilize this functionality. Considering the driver structure
and all error handling it felt best to reuse sony_schedule_work
and sony_cancel_work. The idea was inspired by the wacom driver
which does something similar.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds a new quirk, which allows us to differentiate
between the DualShock 4 USB and the dongle. So far they have
been treated the same, but handling of calibration data differs
as the dongle behaves like Bluetooth, for other requests it
behaves like USB.
In addition this patches changes usb/dongle/bt handling in
sony_raw_event, which makes the code cleaner to read. In addition
another patch in this series will add more dongle logic, so this
change paves the road for that.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DS4 in BT mode sends initial input reports through report 1, which
is described in the HID report descriptors. When activated after sending
a certain feature report, the device uses report 17.
Currently the hid-sony driver fixes up the BT HID report descriptors,
so the HID layer can manage input reports for report 17.
We think it is best to eliminate this fixup and do the handling ourselves,
which is what this patch does. The main motivation is that there are
various users of DS4 through hidraw, including various cross-platform
applications/games, which have their own HID parsing across Linux/Win/OSX.
Due to the fixup the descriptors differ, which is causing pain for many
developers including major game publishers (who reached out privately).
Without the fixup, the Windows titles also have a fighting chance for
working on Wine, which provides HID support now. Overall it felt
best because of these reasons to remove the fixup.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DS4 motion sensors require calibration for accurate operation.
This patch adds calibration for both the accelerometer and the
gyroscope. Calibration requires reading device specific scaling
factors and offsets. For precision reasons we store these values
as a numerator and denominator and apply the values when processing
the data.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DS4 motion sensors are currently mapped by the hid-core driver
to non-existing axes in between ABS_MISC and ABS_MT_SLOT, because
the device already exhausted ABS_X-ABS_RZ. For a part the mapping
by hid-core is accomplished by a fixup in hid-sony as the motion
axes actually use vendor specific usage pages.
This patch makes the DS4 use a separate input device for the motion
sensors and reports acceleration data through ABS_X-ABS_Z and
gyroscope data through ABS_RX-ABS_RZ. In addition it extends the
event spec to allow gyroscope data through ABS_RX-ABS_RZ when
INPUT_PROP_ACCELEROMETER is set. This change was suggested by
Peter Hutterer during a discussion on linux-input.
[jkosina@suse.cz: rebase onto slightly newer codebase]
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Accutouch 2216 is reporting BTN_LEFT/BTN_MOUSE rather than BTM_TOUCH
in it's capabilities, which is what user space expects a touchscreen
device to report. This is causing udev to consider the device to be a
"VMware's USB mouse" rather than as a touchscreen, which results in a
mouse cursor being displayed in Weston.
This patch adds a special driver for the device to correct the
capabilities reported.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It looks like a bunch of devices do not like to be polled
for their reports at init time. When you look into the details,
it seems that for those that are requiring the quirk
HID_QUIRK_NO_INIT_REPORTS, the driver fails to retrieve part
of the features/inputs while others (more generic) work.
IMO, it should be acceptable to remove the need for the quirk
in the general case. On the small amount of cases where
we actually need to read the current values, the driver
in charge (hid-mt or wacom) already retrieves the features
manually.
There are 2 cases where we might need to retrieve the reports at
init:
1. hiddev devices with specific use-space tool
2. a device that would require the driver to fetch a specific
feature/input at plug
For case 2, I have seen this a few time on hid-multitouch. It
is solved in hid-multitouch directly by fetching the feature.
I hope it won't be too common and this can be solved on a per-case
basis (crossing fingers).
For case 1, we moved the implementation of HID_QUIRK_NO_INIT_REPORTS
in hiddev. When somebody starts calling ioctls that needs an initial
update, the hiddev device will fetch the initial state of the reports
to mimic the current behavior. This adds a small amount of time during
the first HIDIOCGUSAGE(S), but it should be acceptable in
most cases. To keep the currently known broken devices, we have to
keep around HID_QUIRK_NO_INIT_REPORTS, but the scope will only be
for hiddev.
Note that I don't think hidraw would be affected and I checked that
the FF drivers that need to interact with the report fields are all
using output reports, which are not initialized by
usbhid_init_reports().
NO_INIT_INPUT_REPORTS is then replaced by HID_QUIRK_NO_INIT_REPORTS:
there is no point keeping it for just one device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes an issue in drivers/hid/hid-input.c where values
outside of the logical range are not clamped when "null state" bit of
the input control is not set.
This was discussed on the lists [1] and this change stems from the fact
due to the ambiguity of the HID specification it might be appropriate to
follow Microsoft's own interpretation of the specification. As noted in
Microsoft's documentation [2] in the section titled "Required HID usages
for digitizers" it is noted that values reported outside the logical
range "will be considered as invalid data and the value will be changed
to the nearest boundary value (logical min/max)."
This patch fixes an issue where the (1292:4745) Innomedia INNEX
GENESIS/ATARI reports out of range values for its X and Y axis of the
DPad which, due to the null state bit being unset, are forwarded to
userspace as is. Now these values will get clamped to the logical range
before being forwarded to userspace. This device was also used to test
this patch.
This patch expands on commit 3f3752705d ("HID: reject input outside
logical range only if null state is set").
[1]: http://lkml.kernel.org/r/20170307131036.GA853@gaia.local
[2]: https://msdn.microsoft.com/en-us/library/windows/hardware/dn672278(v=vs.85).asp
Signed-off-by: Tomasz Kramkowski <tk@the-tk.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit f85c9dc ("Support tool ID and additional tool types") introduced mouse
and lens cursor tools to generic codepath, which covers both display (direct)
and opaque tablets (indirect devices). However, mouse and lens cursor tools are
only provided for opaque tablets. This patch ignores mouse and lens cursor tools
if the device is a display tablet.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse sold by Corsair as Scimitar PRO RGB defines two consecutive
Logical Minimum items in its Application (Consumer.0001) report making
it non parseable. This patch fixes the report descriptor overriding
byte 77 in rdesc from 0x16 (Logical Minimum with 16 bits value) to 0x26
(Logical Maximum with 16 bits value).
Signed-off-by: Oscar Campos <oscar.campos@member.fsf.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 5b779fc introduces the manual release of resources in wacom_remove() as
an addition to the driver's use of devm. The EKR resources can only be
released through wacom_remote_destroy_one() so we skip the manual release for
it.
Fixes: 5b779fc ("HID: wacom: release the resources before leaving despite devm")
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The features struct for the second gen Intuos Pro uses the wrong constant for
the resolution. This fix is for commit 4922cd2.
Fixes: 4922cd2 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Quoting from Jonathan Clarke in previous thread(2017/01/24):
"This division by 2 was added along with the touch width/height fields 6 years
ago so that those fields 'match the visual scale of the touch' for a specific
device (3M PCT)" "The scaling is also discarding information about touch size
(1 bit for each of width/height) which is useful for any application that wants
to know about it."
Jonathan mentioned just what I thought in a new project recently. It dosen't
make sense to discard 1 bit width/height in general case according to the spec
in multi-touch-protocol.txt so I would like to make a slight change here.
A quirk MT_QUIRK_TOUCH_SIZE_SCALING was added to service devices like 3M PCT
with a special visual scale and the division by 2 only take effect with devices
like that.
[jkosina@suse.cz: reformat changelog]
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a user connects a DS4 twice using USB and BT, we reject the
second device connection after the setup work. We then perform
a cleanup, but during cleanup we are not removing the touchpad
device. This leads to leakage of an input device, which we would
never remove. It can likely result into a kernel oops as well
when the touchpad evdev node is accessed and the underlaying HID
device has been removed from the system.
[jkosina@suse.cz: added stable annotation]
Fixes: ac797b95f5 ("HID: sony: Make the DS4 touchpad a separate device")
Cc: stable@vger.kernel.org
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for media keys on the keyboard that comes with the
Asus V221ID and ZN241IC All In One computers.
The keys to support here are WLAN, BRIGHTNESSDOWN and BRIGHTNESSUP.
This device is not visibly branded as Chicony, and the USB Vendor ID
suggests that it is a JESS device. However this seems like the right place
to put it: the usage codes are identical to the currently supported
devices, and this driver already supports the ASUS AIO keyboard AK1D.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use a more common logging style and remove the unnecessary
OOM messages as there is default dump_stack when OOM.
Miscellanea:
o Hoist an assignment in an if
o Realign arguments
o Realign a deeply indented if descendent above a printk
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For mouse devices we can currently change the polling interval
via usbhid.mousepoll. Implement the same thing for joysticks, so
users can reduce input latency this way.
This has been tested with a Logitech RumblePad 2 with jspoll=2,
resulting in a polling rate of 500Hz (verified with evhz).
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to error handling in this function, it is likely that some
resources should be freed before returning.
Replace 'return ret', with 'goto err'.
While at it, remove some spaces at the beginning of the lines to be more
consistent.
Fixes: ead0687fe3 ("HID: i2c-hid: support regulator power on/off")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Cintiq Pro has a softkey to turn touch on/off. Since it is
a softkey, hardware/firmware still reports touch events no matter
what state the softkey is. We need to ignore touch events when
the key is in off mode.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Cintiq Pro added a touch key to switch the tablet between
display and opaque mode. This patch informs the change by removing
the old devices and creating new ones with proper properties.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch add support to the 3 touch keys on Wacom Cintiq Pro. These touch
keys are in the middle of the other two keys on the top edge of the tablet.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The (1292:4745) Innomedia INNEX GENESIS/ATARI adapter needs
HID_QUIRK_MULTI_INPUT to split the device up into two controllers
instead of inputs from both being merged into one.
Signed-off-by: Tomasz Kramkowski <tk@the-tk.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes an issue in drivers/hid/hid-input.c where USB HID
control null state flag is not checked upon rejecting inputs outside
logical minimum-maximum range. The check should be made according to USB
HID specification 1.11, section 6.2.2.5, p.31. The fix will resolve
issues with some game controllers, such as:
https://bugzilla.kernel.org/show_bug.cgi?id=68621
[tk@the-tk.com: shortened and fixed spelling in commit message]
Signed-off-by: Valtteri Heikkilä <rnd@nic.fi>
Signed-off-by: Tomasz Kramkowski <tk@the-tk.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On some boards, we need to enable a regulator before using the HID, and
it's also nice to save power in suspend by disabling it. Support an
optional "vdd-supply" and a companion initialization delay.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: linux-input@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The LED subsystem provides the LED_CORE_SUSPENDRESUME flag to handle
automatically turning off and restoring the state of device LEDs during
suspend/resume. Use this flag instead of saving and restoring the state
locally.
Signed-off-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
