Always jump to the place where the kernel is linked to. This helps where
the bootloaders/proms ignores the start address inside the ELF header.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As IP22 is now using do_IRQ for timer interrupt, don't mess with
interrupt handler any longer
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some processors offer the option of using the interrupt on which
normally the count / compare interrupt would be signaled as a normal
interupt pin. Previously this required some ugly hackery for each
system which is much easier done by a quick and simple probe.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Userland, including the C library and the dynamic linker, is keen to use
the SYNC instruction, even for "generic" MIPS I binaries these days.
Which makes it less than useful on MIPS I processors.
This change adds the emulation, but as our do_ri() infrastructure was not
really prepared to take yet another instruction, I have rewritten it and
its callees slightly as follows.
Now there is only a single place a possible signal is thrown from. The
place is at the end of do_ri(). The instruction word is fetched in
do_ri() and passed down to handlers. The handlers are called in sequence
and return a result that lets the caller decide upon further processing.
If the result is positive, then the handler has picked the instruction,
but a signal should be thrown and the result is the signal number. If the
result is zero, then the handler has successfully simulated the
instruction. If the result is negative, then the handler did not handle
the instruction; to make it more obvious the calls do not follow the usual
0/-Exxx result convention they now return -1 instead of -EFAULT.
The calculation of the return EPC is now at the beginning. The reason is
it is easier to handle it there as emulation callees may modify a register
and an instruction may be located in delay slot of a branch whose result
depends on the register. It has to be undone if a signal is to be raised,
but it is not a problem as this is the slow-path case, and both actions
are done in single places now rather than the former being scattered
through emulation handlers.
The part of do_cpu() being covered follows the changes to do_ri().
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
Remove the old-fashioned lk201 driver under drivers/tc/ that used to be
used by the old dz.c and zs.c drivers, which is now orphan code referred to
from nowhere and does not build anymore. A modern replacement is available
as drivers/input/keyboard/lkkbd.c.
There are no plans to do anything about this piece of code and it does not
fit anywhere anymore, so it is not just a matter of maintenance or the lack
of. There are still some bits that might be added to the new lkkbd.c
driver based on the old code, and the embedded hardware documentation which
is otherwise quite hard to get hold of might be useful to keep too. Both
of these can be done separately though. RIP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_cache_(wback|inv|wback_inv) were the earliest attempt on a generalized
cache managment API for I/O purposes. Originally it was basically the raw
MIPS low level cache API exported to the entire world. The API has
suffered from a lack of documentation, was not very widely used unlike it's
more modern brothers and can easily be replaced by dma_cache_sync. So
remove it rsp. turn the surviving bits back into an arch private API, as
discussed on linux-arch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All asm/ipc.h files do only #include <asm-generic/ipc.h>.
This patch therefore removes all include/asm-*/ipc.h files and moves the
contents of include/asm-generic/ipc.h to include/linux/ipc.h.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some time /proc/sys/kernel/core_pattern has been able to set its output
destination as a pipe, allowing a user space helper to receive and
intellegently process a core. This infrastructure however has some
shortcommings which can be enhanced. Specifically:
1) The coredump code in the kernel should ignore RLIMIT_CORE limitation
when core_pattern is a pipe, since file system resources are not being
consumed in this case, unless the user application wishes to save the core,
at which point the app is restricted by usual file system limits and
restrictions.
2) The core_pattern code should be able to parse and pass options to the
user space helper as an argv array. The real core limit of the uid of the
crashing proces should also be passable to the user space helper (since it
is overridden to zero when called).
3) Some miscellaneous bugs need to be cleaned up (specifically the
recognition of a recursive core dump, should the user mode helper itself
crash. Also, the core dump code in the kernel should not wait for the user
mode helper to exit, since the same context is responsible for writing to
the pipe, and a read of the pipe by the user mode helper will result in a
deadlock.
This patch:
Remove the check of RLIMIT_CORE if core_pattern is a pipe. In the event that
core_pattern is a pipe, the entire core will be fed to the user mode helper.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Cc: <martin.pitt@ubuntu.com>
Cc: <wwoods@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch single-linked binfmt formats list to usual list_head's. This leads
to one-liners in register_binfmt() and unregister_binfmt(). The downside
is one pointer more in struct linux_binfmt. This is not a problem, since
the set of registered binfmts on typical box is very small -- (ELF +
something distro enabled for you).
Test-booted, played with executable .txt files, modprobe/rmmod binfmt_misc.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Increase cp0 compare clockevent min_delta_ns from 0x30 to 0x300.
[MIPS] Cache: Provide more information on cache policy on bootup.
[MIPS] Fix aliasing bug in copy_user_highpage, take 2.
[MIPS] VPE loader: convert from struct class_ device to struct device
[MIPS] MIPSsim: Fix booting from NFS root
[MIPS] Alchemy: Get rid of au1xxx_irq_map_t.
[MIPS] Alchemy: Get rid of au_ffz().
[MIPS] Alchemy: Get rid of au_ffs().
[MIPS] Alchemy: cleanup interrupt code.
[MIPS] Lasat: Fix build by conversion to irq_cpu.c.
[MIPS] Lasat: Add #ifndef ... #endif include warpper to lasatint.h.
[MIPS] IP22: Enable -Werror.
[MIPS] IP22: Fix warning.
[MIPS] IP22: Complain if requesting the front panel irq failed.
[MIPS] vmlinux.lds.S: Handle KPROBES_TEXT.
[MIPS] vmlinux.lds.S: Fix handling of .notes in final link.
[MIPS] vmlinux.lds.S: Remove duplicate comment.
[MIPS] MSP71XX: Add workarounds file.
[MIPS] IP32: Fix build by conversion to irq_cpu.c.
Extremly low values are of dubious usefulness anyway but in this case
they actually were killing Qemu which simply wasn't able to complete
mips_next_event() within 0x30 100MHz cycles even on fast hosts.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This should help making bug reports for the gadzillion of cores with all
their configuration and synthesis options more useful.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Turns out b868868ae0 wasn't quite right.
When called for a page that isn't marked dirty it would artificially
create an alias instead of doing the obvious thing and access the page
via KSEG0.
The same issue also exists in copy_to_user_page and copy_from_user_page
which was causing the machine to die under rare circumstances for example
when running ps if the BUG_ON() assertion added by the earlier fix was
getting triggered.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPSsim probably doesn't have any sort of environment, but writing
a zero in it kills even the compiled in command line. This prevents
booting via NFS root.
Signed-Off-By: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip22/ip22-berr.o
arch/mips/sgi-ip22/ip22-berr.c: In function 'ip22_be_interrupt':
arch/mips/sgi-ip22/ip22-berr.c💯 warning: passing argument 2 of 'die_if_kernel' discards qualifiers from pointer target type
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes the warning:
CC arch/mips/sgi-ip22/ip22-reset.o
arch/mips/sgi-ip22/ip22-reset.c: In function 'reboot_setup':
arch/mips/sgi-ip22/ip22-reset.c:239: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rtc-ds1742 platform driver name doesn't match its module name,
which might prevents it from properly hotplugging. There is only two
in-tree user of its driver, which are fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory
condition.
Killing just one of the process threads can leave the application in a bad
state, whereas killing the entire process group would allow for the
application to restart, or be otherwise handled, and makes it very obvious
that something has gone wrong.
This change allows the entire process group to be taken down, rather
than just the one thread.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Identical handlers of PTRACE_DETACH go into ptrace_request().
Not touching compat code.
Not touching archs that don't call ptrace_request.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The variable AFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of AFLAGS with KBUILD_AFLAGS all over
the tree.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k, s390
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Update AU1000 get_ethernet_addr().
Three functions were brought together in one.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The variable CFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of CFLAGS with KBUILD_CFLAGS all over the
tree and enabling one to use:
make CFLAGS=...
to specify additional gcc commandline options.
One usecase is when trying to find gcc bugs but other
use cases has been requested too.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k
Test was simple to do a defconfig build, apply the patch and check
that nothing got rebuild.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
[SKY2]: status polling loop (post merge)
[NET]: Fix NAPI completion handling in some drivers.
[TCP]: Limit processing lost_retrans loop to work-to-do cases
[TCP]: Fix lost_retrans loop vs fastpath problems
[TCP]: No need to re-count fackets_out/sacked_out at RTO
[TCP]: Extract tcp_match_queue_to_sack from sacktag code
[TCP]: Kill almost unused variable pcount from sacktag
[TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
[TCP]: Add bytes_acked (ABC) clearing to FRTO too
[IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
[NETFILTER]: x_tables: add missing ip6t_modulename aliases
[NETFILTER]: nf_conntrack_tcp: fix connection reopening
[QETH]: fix qeth_main.c
[NETLINK]: fib_frontend build fixes
[IPv6]: Export userland ND options through netlink (RDNSS support)
[9P]: build fix with !CONFIG_SYSCTL
[NET]: Fix dev_put() and dev_hold() comments
[NET]: make netlink user -> kernel interface synchronious
[NET]: unify netlink kernel socket recognition
[NET]: cleanup 3rd argument in netlink_sendskb
...
Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.
(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Loading ELF binaries based on the section table is totally wrong. This
still leaves the other fat bug of referencing symbols in an executable
unfixed, so people better don't run strip on their binaries ...
As added bonus the new loader is also 23 lines shorter.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So far /proc/cpuinfo has been the only user but human readable processor
name are more useful than that for proc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dump the generated code for clear/copy page calls like it is done for TLB
fault handlers. Useful for debugging.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's only used in arch/mips/cobalt/reset.c.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They're only used in arch/mips/cobalt/console.c.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These PCI definitions are only used in arch/mips/pci/fixup-cobalt.c.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add Cobalt Qube series front LED support to platform register.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On MP configurations it's highly dubious what this code will actually
affect since blasting away cachelines may or may not do the right
thing wrt. cache coherency.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-msym32 and previously the strategy to tell the compiler to generate
64-bit code but the assembler to put it into 32-bit ELF was initially
a hack to get around the lack of proper 64-bit binutils support and
later turned into a neat optimization with significant code size
savings. But it's really just an optimization so there is nothing
wrong with just dropping the option (and whatever else goes along with
it, I forgot all the nasty details) on the floor if due to a vintage
compiler it can't be suported.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel currently only supports broadcasting of the timer interrupt
from a single timer, not multicasting into two multicast groups of
processors. So the implemented mechanism for SMTC works by broadcasting
the cp0 compare interrupt on VPE 0 and ignoring it on any additional VPEs.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This replaces the MIPS-specific to_tm function with the generic
rtc_time_to_tm function. The big difference between the two functions is
that rtc_time_to_tm uses epoch 70 while to_tm uses 1970, so the result of
rtc_time_to_tm needs to be fixed up.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hard to follow who is pointing what to where and why so it's simply getting
in the way of the time code renovation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This has not been any serious user of this ill conceived thing since the
original invention in like '95.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add LED support to the WGT634U machine. It uses the new gpio-led
driver and a platform driver for the pin definitions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add GPIO support to the BCM47XX platform. It will be used by a GPIO
LED driver.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add CFE support to the BCM47XX code. That includes querying CFE environment
variables as well as using CFE to print messages before the serial port is
initialized (early printk).
Signed-off-by: Aurelien Jarno <aurel32@farad.aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the platform independent part of the CFE code to arch/mips/fw/cfe from
arch/mips/sibyte/cfe.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It may not be perfect yet but the SB1 code is badly borken and has
horrible performance issues.
Downside: This seriously breaks support for pass 1 parts of the BCM1250
where indexed cacheops don't work quite reliable but I seem to be the
last one on the planet with a pass 1 part anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Match the R4000 semantics for the initial state of interrupt/kernel
status register flags for the R3000 in kernel_thread().
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This style will be consitent with all other arch's - soon.
In addition:
- Moved a few labels inside brackets for the sections they specify
to prevent that linker alignmnet made them point before the section start
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Move i8259 function declarations to include/asm-mips/i8259.h
o Make i8259.c functions static where possible.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Note that the BCM4710 does not support the wait instruction, this
is not a mistake in the code.
It originally comes from the OpenWrt patches.
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Florian Schirmer <jolt@tuxbox.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch renames it for 3 reasons:
- "CONFIG" pattern is used by Kconfig. Now this macro is
no more defined by Kconfig but by Kbuild itself make this
clear by translating "CONFIG" into "KBUILD".
- "ELF32" word is improper because it is irrelevant to ELF
format and it makes confusion with CONFIG_BOOT_ELF32. So
translate it with SYM32.
- Add "64BIT" part to make clear that this macro implies a
64 bits kernel.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We do not rely on user anymore to setup this config correctly.
Instead we make our choice depending on the load address.
If we want to force Kbuild to use ELF64 format whatever
the load address we can still do:
$ make BUILD_ELF32=no
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes '-mno-explicit-relocs' usage when
CONFIG_BUILD_ELF64 is set since this option was only required
with the old hack to truncate addresses at the assembly level
where "-mabi=64 -Wa,-mabi=32" was used.
This should yield a small code size improvement for inline
assembly, where the R constraint is used.
The idea is coming from Maciej <macro@linux-mips.org>.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rename NET_SB1250_MAC to SB1250_MAC to follow the convention.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PCI controller IO base was not set in the au1000 pci code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes a wrong ifdef in the board setup code, leading to the GPIO
pin not being pulled high, and thus the USB switch not being powered at all.
This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which
started in 2005 (before 2.6.12-rc2), then probably because things were
working anyway for most people got forgotten.
[Ralf: Paolo's original patch didn't fix the module case, Florian's patch
only fixed MTX1 etc. so this is a combined patch plus some cleanups.]
Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixe MACE PCI addressing by adding the bus number parameter.
Remove check of the used slot since every slot should be valid.
Converted mkaddr from #define to inline function.
Signed-off-by: Giuseppe Sacco <eppesuig@debian.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Restore a load from KSEG1 done as a workaround for an R4600 v2
erratum, dropped with 211be16de99a7424e66c0b6c0d00e2c970508ac2.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Store any note sections after the exception tables like the other
architectures do. This is required for .note.gnu.build-id emitted from
binutils 2.18 onwards if nothing else.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS was mistakenly forgetting to use the fallocate compat wrapper, which
I noticed while cleaning up all the duplicate fallocate wrappers.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a workaround to address warnings generated on the "n" constraint by
GCC 3.3 and below.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the definition of the ioasic_ssr_lock spinlock to include a proper
initialisation.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Another issue with 20Kc's WAIT, waiting for more details. With the
2.6.23 release immindent simply disable the use of WAIT instead of a
more fancy workaround.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fairly cosmetic as it would only affect VSMP / SMTC kernels that don't
use vectored interrupts.
Found by Beth.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It refer to CPU_PROFILING.
arch/mips/kernel/time.c: In function 'local_timer_interrupt':
arch/mips/kernel/time.c:142: error: implicit declaration of function 'profile_tick'
arch/mips/kernel/time.c:142: error: 'CPU_PROFILING' undeclared (first use in this function)
arch/mips/kernel/time.c:142: error: (Each undeclared identifier is reported only once
arch/mips/kernel/time.c:142: error: for each function it appears in.)
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/kernel/rtlx.o
cc1: warnings being treated as errors
arch/mips/kernel/rtlx.c:59: warning: 'irq' defined but not used
arch/mips/kernel/rtlx.c:60: warning: 'irq_num' defined but not used
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/kernel/rtlx.o
arch/mips/kernel/rtlx.c: In function 'rtlx_init':
arch/mips/kernel/rtlx.c:114: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Copy_user_highpage was written assuming it was only being called for
breaking COW pages in which case the source page isn't cached as in
marked cachable under it kernel virtual address. If it is called anyway
the aliasing avoidance strategy implemented by kmap_coherent will fail.
Avoid the use of kmap_coherent for pages marked dirty and to avoid
another instance of this sort of bug, place a BUG_ON in kmap_coherent.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix wrong argument order; this is just a minimal fix for the half baked
redadb/writeb() conversion.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Wrong check for the second hpc on fullhouse machines, caused DBEs on
SGI Indys
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sibyte/bcm1480/irq.o
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_mask_irq':
arch/mips/sibyte/bcm1480/irq.c:112: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:114: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_unmask_irq':
arch/mips/sibyte/bcm1480/irq.c:130: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:132: warning: cast to pointer from integer of different size
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct the name of the spi_txx9 driver (and their in-tree user)
instead of MODULE_ALIAS workaround. This would be preferable in the
long term.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
shutdown_bridge_irq disconnects the irq so we need to connect the irq or
requesting the same irq a send time will fail. This used to make
things like ifconfig eth0 down; ifconfig eth0 up fail on IP27.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Certain 32-bit kernel configurations seem to be able to cause references,
this was observed with gcc 4.1.2.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d several callers of
pcibios_resource_to_bus are no longer marked __devinit resulting in a
pile of modpost warnings if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x15dde8): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_map_rom' and 'pci_map_rom_copy')
WARNING: vmlinux.o(.text+0x15e140): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_update_resource' and 'pci_claim_resource')
WARNING: vmlinux.o(.text+0x15f0cc): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f0f0): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f114): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f138): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f438): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
WARNING: vmlinux.o(.text+0x15f4f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
Removing __devinit from pcibios_resource_to_bus make the same necessary
for pcibios_fixup_device_resources as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d pcibios_fixup_bus's caller
pci_scan_child_bus is no longer marked __devinit resulting in this modpost
warning if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x158b9c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The appended patch adds code to update siginfo_t's si_code field. It
fixes e.g. a floating point overflow regression in the SBCL testsuite.
Signed-off-By: Thiemo Seufer <ths@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Also removes the while(1); loop by propagating the ATTRIB_NORET of die()
to nmi_exception_handler.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rtc-rs5c348 SPI driver name doesn't match its module name, which
prevents it from properly hotplugging. There is only one in-tree user
of its driver, which is fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/basler/excite/excite_prom.o
arch/mips/basler/excite/excite_prom.c:136:3: #error 64 bit support not implemented
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS doesn't do CPU hotplugging yet but since many of the functions don't
even have an __init let's fix this right.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leaving these sections is useful to some tools that look at the image, and
none of them are loaded into memory. The .mdebug.abi64 section, in
particular, lets GDB recognize vmlinux.32 as an N64 program instead of
guessing that it is O32.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add generic irq_chip for TX39/TX49 SoCs. This can be replace
jmr3927_irq_irc, tx4927_irq_pic_type and tx4938_irq_pic_type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is needed since the Sibyte serial driver was exchanged.
Issue report by Imre Kaloz <kaloz@openwrt.org>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
