* 'board' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: add minimal support for Nokia RM-696
ARM: OMAP: enable Bluetooth on the PandaBoard
ARM: OMAP: pandora: add support for backlight and poweroff
ARM: OMAP4: board-4430sdp: don't initialize value that is never used
ARM: OMAP3: cm-t3517: add EMAC support
ARM: OMAP: move generic EMAC init to separate file
ARM: OMAP3: RX-51: add explicit mux configuration of tsc2005 control gpios
ARM: OMAP: Add omap_reserve functionality
(includes sync-up to 3.3-rc6)
* 'ams-delta' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ASoC: OMAP: ams-delta: drop .set_bias_level callback
ARM: OMAP1: ams-delta: update the modem to use regulator API
ARM: OMAP1: ams-delta: set up regulator over modem reset GPIO pin
ARM: OMAP1: ams-delta: clean up init data section assignments
ARM: OMAP1: ams-delta: fix incorrect section tags
This functionality has already been implemented in the cx20442 codec
driver (commit f75a8ff67d, "ASoC: cx20442:
add bias control over a platform provided regulator"), no need to keep
it here duplicated.
Once done, remove the no longer used AMS_DELTA_LATCH2_MODEM_NRESET
symbol from the board header file and a call to the regulator_toggle()
helper function from the old API wrapper found in the board file. While
being at it, simplify the way the modem .pm callback handles the
regulator and drop that helper function and its related consumer setup
completely.
Depends on patches 1/3 and 2/3 for clean apply and keep things working.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
input: serio: ams-delta: toggle keyboard power over GPIO
omapfb: lcd_ams_delta: drive control lines over GPIO
MTD: NAND: ams-delta: use GPIO instead of custom I/O
LED: drop leds-ams-delta driver
ARM: OMAP1: ams-delta: supersede custom led device by leds-gpio
ARM: OMAP1: ams-delta: convert latches to basic_mmio_gpio
ARM: OMAP1: ams-delta: register latch dependent devices later
The following commit: 2f31b51659
Author: Tero Kristo <t-kristo@ti.com>
Date: Fri Dec 16 14:37:00 2011 -0700
ARM: OMAP4: PRM: use PRCM interrupt handler
introduced the PRCM interrupt handler and thus the need
for 64 more interrupts. Since SPARSE_IRQ is still not fully
functional on OMAP, the NR_IRQS needs to be updated to avoid
the failure that happen during irq_alloc_descs call inside
the PRCM driver:
[ 0.208221] PRCM: failed to allocate irq descs: -12
Later the mux framework is then unable to request an IRQ from
the PRCM interrupt handler.
[ 1.802795] mux: Failed to setup hwmod io irq -22
Fix that by adding 64 more interrupts for OMAP2PLUS config.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arm_memblock_steal() is not suppose to be used outside ->reserve callback.
OMAP barrier errata code was using it outside reserve callback and hence
it was broken.
Move the allocation as part of ->reserve callback to fix the it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the latest Sourcery G++ Lite 2011.03-41 and latest linaro
tool-chains OMAP2 only build breaks with below error.
arch/arm/mach-omap2/omap-smc.S: Assembler messages:
arch/arm/mach-omap2/omap-smc.S:30: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:53: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:61: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:69: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:77: Error: selected processor does not support ARM mode `smc #0'
make[1]: *** [arch/arm/mach-omap2/omap-smc.o] Error 1
OMAP2 devices doesn't have the security support but the security support
was getting built because of OMAP2PLUS. Don't build security code for
OMAP2 devices.
While at it, fix the secure-common line in the Makefile to use tabs
instead of spaces.
Reported-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Several platforms are now using the memblock_alloc+memblock_free+
memblock_remove trick to obtain memory which won't be mapped in the
kernel's page tables. Most platforms do this (correctly) in the
->reserve callback. However, OMAP has started to call these functions
outside of this callback, and this is extremely unsafe - memory will
not be unmapped, and could well be given out after memblock is no
longer responsible for its management.
So, provide arm_memblock_steal() to perform this function, and ensure
that it panic()s if it is used inappropriately. Convert everyone
over, including OMAP.
As a result, OMAP with OMAP4_ERRATA_I688 enabled will panic on boot
with this change. Mark this option as BROKEN and make it depend on
BROKEN. OMAP needs to be fixed, or 137d105d50 (ARM: OMAP4: Fix
errata i688 with MPU interconnect barriers.) reverted until such
time it can be fixed correctly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: (23 commits)
[CPUFREQ] EXYNOS: Removed useless headers and codes
[CPUFREQ] EXYNOS: Make EXYNOS common cpufreq driver
[CPUFREQ] powernow-k8: Update copyright, maintainer and documentation information
[CPUFREQ] powernow-k8: Fix indexing issue
[CPUFREQ] powernow-k8: Avoid Pstate MSR accesses on systems supporting CPB
[CPUFREQ] update lpj only if frequency has changed
[CPUFREQ] cpufreq:userspace: fix cpu_cur_freq updation
[CPUFREQ] Remove wall variable from cpufreq_gov_dbs_init()
[CPUFREQ] EXYNOS4210: cpufreq code is changed for stable working
[CPUFREQ] EXYNOS4210: Update frequency table for cpu divider
[CPUFREQ] EXYNOS4210: Remove code about bus on cpufreq
[CPUFREQ] s3c64xx: Use pr_fmt() for consistent log messages
cpufreq: OMAP: fixup for omap_device changes, include <linux/module.h>
cpufreq: OMAP: fix freq_table leak
cpufreq: OMAP: put clk if cpu_init failed
cpufreq: OMAP: only supports OPP library
cpufreq: OMAP: dont support !freq_table
cpufreq: OMAP: deny initialization if no mpudev
cpufreq: OMAP: move clk name decision to init
cpufreq: OMAP: notify even with bad boot frequency
...
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=P4kO
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
power management changes for omap and imx
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
ARM: imx6q: build pm code only when CONFIG_PM selected
ARM: mx5: use generic irq chip pm interface for pm functions on
ARM: omap: pass minimal SoC/board data for UART from dt
arm/dts: Add minimal device tree support for omap2420 and omap2430
omap-serial: Add minimal device tree support
omap-serial: Use default clock speed (48Mhz) if not specified
omap-serial: Get rid of all pdev->id usage
ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
ARM: OMAP4: PRM: use PRCM interrupt handler
ARM: OMAP3: pm: use prcm chain handler
ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
ARM: OMAP2+: mux: add support for PAD wakeup interrupts
ARM: OMAP: PRCM: add suspend prepare / finish support
ARM: OMAP: PRCM: add support for chain interrupt handler
ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
...
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lYb/
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Board-level changes
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
Enable 32 bit flash support for iMX21ADS board
ARM: mx31pdk: Add MC13783 RTC support
iomux-mx25: configuration to support CSPI3 on CSI pins
MX1:apf9328: Add i2c support
mioa701: add newly available DoC G3 chip
arm/tegra: remove __initdata annotation from pinmux tables
arm/tegra: Use bus notifiers to trigger pinmux setup
arm/tegra: Refactor board-*-pinmux.c to share code
arm/tegra: Fix mistake in Trimslice's pinmux
arm/tegra: Rework Seaboard-vs-Ventana pinmux table
arm/tegra: Remove useless entries from ventana_pinmux[]
arm/tegra: PCIe: Remove include of mach/pinmux.h
arm/tegra: Harmony PCIe: Don't touch pinmux
arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio
arm/tegra: Split Seaboard GPIO table to allow for Ventana
ARM: imx6q: generate imx6q dtb files
arm/imx6q: Rename Sabreauto to Armadillo2
arm/imx6q-sabrelite: add enet phy ksz9021rn fixup
arm/imx6: add imx6q sabrelite board support
dts/imx: rename uart labels to consistent with hw spec
...
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hp8k
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
SoC-level changes for tegra and omap
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF
arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC
arm/tegra: Delete tegra_init_clock()
arm/tegra: Fix section mismatch errors in tegra30 pinmux
arm/tegra: Fix section mismatch errors in tegra20 pinmux
arm/tegra: refresh defconfig for tegra30
arm/tegra: add support for tegra30 based board cardhu
arm/tegra: implement support for tegra30
arm/tegra: pinmux tables and definitions for tegra30
arm/tegra: add new fields to struct tegra_pingroup_desc
arm/tegra: prepare pinmux code for multiple tegra variants
arm/tegra: rename tegra20 pinmux files
arm/tegra: generalize L2 cache initialization
arm/tegra: use PMC reset
arm/tegra: rename board-dt.c to board-dt-tegra20.c
arm/tegra: prepare early init for multiple tegra variants
arm/tegra: don't export clk_measure_input_freq
arm/tegra: prepare clock code for multiple tegra variants
arm/tegra: cleanup tegra20 support
arm/tegra: clk_get should not be fatal
...
Fix up trivial conflict in arch/arm/mach-tegra/board-dt-tegra20.c
Simple bug fixes that were not considered important enough for inclusion
into 3.2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UU7m
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Non-critical bug fixes
Simple bug fixes that were not considered important enough for inclusion
into 3.2.
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update pxa and mmp
ARM: pxa: Include linux/export.h in balloon3.c
ARM: OMAP4: clock: Add CPU local timer clock node
ARM: OMAP4: hwmod: Don't wait for the idle status if modulemode is not supported
ARM: OMAP: AM3517/3505: fix crash on boot due to incorrect voltagedomain data
ARM: OMAP: hwmod data: fix the panic on Nokia RM-680 during boot
ARM: OMAP2+: DMA: Workaround for invalid destination position
ARM: OMAP2+: DMA: Workaround for invalid source position
Conflicts:
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-omap2/board-ti8168evm.c
arch/arm/mach-s3c64xx/Kconfig
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/common.c
Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* omap/hwmod:
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: OMAP: hwmod data: fix the panic on Nokia RM-680 during boot
ARM: OMAP: hwmod data: fix iva and mailbox hwmods for OMAP 3
ARM: OMAP: rx51: fix USB
ARM: OMAP: mcbsp: Fix possible memory corruption
Don't use Amstrad Delta custom I/O functions once GPIO interface is
available for the underlying hardware.
While requesting and initializing GPIO pins used, also take care of one
extra pin KEYBRD_DATAOUT which, even if not used by the driver, belongs
to the device and affects its functioning.
Once done, move the driver initialization back to the device_initcall
level, reverting the temporary chane introduced with patch 1/7 "ARM:
OMAP1: ams-delta: register latch dependent devices later". That change
is no longer required once the driver takes care of registering used
GPIO pins, and it's better to initialize the device before others using
the latch2 based GPIO pins, otherwise a garbage is reported on boot,
perhaps due to random data already captured by the FIQ handler while the
keyboard related latch bits are written with random values during
initialization of those other latch2 dependent devices.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
[tony@atomide.com: renamed _gpios to ams_delta_gpios]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions any longer, use GPIO API
instead.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions for controlling the device,
use GPIO API instead.
While being at it, add missing gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that the Amstrad Delta on-board latches have been converted to GPIO
devices, use the generic driver to control on-board LEDs which hang off
those latches.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Once ready, ams-delta specific device drivers currently calling custom
ams_delta_latch[12]_write() functions can be updated to call generic
gpio_set_value() instead, which will make them less platform dependent.
Even more, some custom ams-delta only drivers can perhaps be dropped
from the tree after converting selected ams-delta platform devices to
follow generic GPIO based device models.
The latch_gpios[] table is initially filled with all latch1 and latch2
GPIO pins in order to register and initialize them from the board file
until those are handled by respective existing device drivers (leds,
nand, lcd, serio, asoc, serial). That table will get almost empty after
the transision process is completed, holding only pins not used by any
drivers / connected to unused devices, in order to initialize them from
the board file for power saving purposes.
The new ams_delta_latch_write() function is a unified replacement for
those removed ams_delta_latch[12]_write(), and serves as a temporary
wrapper over gpio_set_value(), providing the old API for those not yet
updated device drivers, and will be removed after all custom drivers are
converted or replaced.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
An hwmod with a 'HWMOD_INIT_NO_IDLE' flag set, is left in
enabled state by the hwmod framework post the initial setup.
Once a real user of the device (a driver) tries to enable it
at a later point, the hwmod framework throws a WARN() about
the device being already in enabled state.
Fix this by introducing a new internal flag '_HWMOD_SKIP_ENABLE' to
identify such devices/hwmods. When the device/hwmod is requested to be
enabled (the first time) by its driver/user, nothing except the
mux-enable is needed. The mux data is board specific and is
unavailable during initial enable() of the device, done by the
framework as part of setup().
A good example of a such a device is an UART used as debug console.
The UART module needs to be kept enabled through the boot, until the
UART driver takes control of it, for debug prints to appear on
the console.
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use a flag rather than a state; updated commit message;
edited some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By default all registered pads will trigger mpu_irqs[0]. Now there is
an API for selecting used mpu_irq on pad basis, which can be used to
trigger different irq handlers for different pads in the same hwmod.
Each pad that requires its interrupt to be re-routed this way must
have a separate call to omap_hwmod_pad_route_irq(hwmod, pad, irq).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved fn to omap_hwmod.c; separated fn from mux scan_wakeups
changes; added kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP mux now parses active wakeup events from pad registers and calls
corresponding hwmod ISRs once a wakeup is detected. This is
accomplished by registering an interrupt handler for PRCM IO event,
which is raised every time the HW detects wakeups.
[paul@pwsan.com: This patch is a merge of Govindraj R's "ARM: OMAP2+:
hwmod: Add API to check IO PAD wakeup status" patch, Tero Kristo's
"ARM: OMAP2+: mux: add support for PAD wakeup interrupts" patch, and
part of Tero's "ARM: OMAP: mux: add support for selecting mpu_irq for
each wakeup pad" patch.]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: reduced indentation level; renamed omap_hwmod function;
improved function documentation; modified to iterate only through dynamic
pads; modified to skip pads where idle mode doesn't enable wakeups; split
patches]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The ehci and ohci drivers does not use the APIs of the usbhs
core driver; the runtime pm APIs are used for clock
enable/disable. Since usbhs is parent platform device of the
ehci and ohci devices, the runtime apis indirectly uses the
usb hs core device as input parameter to for clock functions.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod support to enable access to UART4 of the AM35xx series of
chips. The UART4 device referenced from the TRM will show up as ttyO3.
This was tested on an AM3505.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Omap_uart_can_sleep function blocks system wide low power state until
uart is active remove this func and add qos requests to prevent
MPU from transitioning.
Keep qos request to default value which will allow MPU to transition
and while uart baud rate is available calculate the latency value
from the baudrate and use the same to hold constraint while uart clocks
are enabled, and if uart is auto-idled the constraint is updated with
default constraint value allowing MPU to transition.
Qos requests are blocking notifier calls so put these requests to
work queue, also the driver uses irq_safe version of runtime API's
and callbacks can be called in interrupt disabled context.
So to avoid warn on slow path warning while using qos update
API's from runtime callbacks use the qos_work_queue.
During bootup the runtime_resume call backs might not be called and runtime
callback gets called only after uart is idled by setting the autosuspend
timeout. So qos_request from runtime resume callback might not activated during
boot if uart baudrate is calculated during bootup for console uart, so schedule
the qos_work queue once we calc_latency while configuring the uart port.
Flush and complete any pending qos jobs in work queue while suspending.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
When using DMA there are two timeouts defined. The first timeout,
rx_timeout, is really a polling rate in which software polls the
DMA status to see if the DMA has finished. This is necessary for
the RX side because we do not know how much data we will receive.
The secound timeout, RX_TIMEOUT, is a timeout after which the
DMA will be stopped if no more data is received. To make this
clearer, rename rx_timeout as rx_poll_rate and rename the
function serial_omap_rx_timeout() to serial_omap_rxdma_poll().
The OMAP-Serial driver defines an RX_TIMEOUT of 3 seconds that is
used to indicate when the DMA for UART can be stopped if no more
data is received. The value is a global definition that is applied
to all instances of the UART.
Each UART may be used for a different purpose and so the timeout
required may differ. Make this value configurable for each UART so
that this value can be optimised for power savings.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
The following UART parameters are defined within the UART driver:
1). Whether the UART uses DMA (dma_enabled), by default set to 0
2). The size of dma buffer (set to 4096 bytes)
3). The time after which the dma should stop if no more data is received.
4). The auto suspend delay that will be passed for pm_runtime_autosuspend
where uart will be disabled after timeout
Different UARTs may be used for different purpose such as the console,
for interfacing bluetooth chip, for interfacing to a modem chip, etc.
Therefore, it is necessary to be able to customize the above settings
for a given board on a per UART basis.
This change allows these parameters to be configured from the board file
and allows the parameters to be configured for each UART independently.
If a board does not define its own custom parameters for the UARTs, then
use the default parameters in the structure "omap_serial_default_info".
The default parameters are defined to be the same as the current settings
in the UART driver to avoid breaking the UART for any cuurnelty supported
boards. By default, make all boards use the default UART parameters.
Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
