When the crash kernel is loaded after crash, the device is in unknown state.
So reset the device contexts prior to its creation in case of kdump,
depending upon kernel parameter reset_devices.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unmap mapped IO in wd_probe1() if register_netdev() failed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o NPAR configuration which is programmed in fw, need to
restore after fw recovery.
o Update version to 5.0.7
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci error recovery support added.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev notifier are not unregistered if pci_register_driver fails.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable tx timeout recovery, if auto_fw_reset is disable
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning off rx pause param and autoneg param is not supported so
return error in that case.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETRAX_NETWORK_RED_ON_NO_CONNECTION doesn't exist in Kconfig, therefore
removing all references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
SH_HICOSH4 doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CASSINI_NAPI doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CASSINI_MULTICAST_REG_WRITE doesn't exist in Kconfig, therefore
removing all references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CASSINI_QGE_DEBUG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
{AR,WAVE}LAN doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b31fb86815.
pcim_*() managed drivers do not need explicit resource
releasing like this.
Signed-off-by: David S. Miller <davem@davemloft.net>
Body of the explanation:
-support 16bit and 32bit bus width.
-add device reset for ks8842/8841 Micrel device.
-set 100Mbps as a default for Micrel device.
-set MAC address in both MAC/Switch layer with different sequence for Micrel
device, as mentioned in data sheet.
-use private data to set options both 16/32bit bus width and Micrel device/
Timberdale(FPGA).
-update Kconfig in order to put more information about ks8842 device.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the driver version from the driver. This version
hasn't changed since the driver's inclusion in the kernel and is a
source of confusion for some customers.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the move to phylib (commit e6b043d) I was seeing sporadic "MDIO write
timeout" messages. Measure of the actual time spent showed latency times of
more than 1600us.
This patch uses the MII event indication of the FEC hardware to detect
completion of MDIO transactions.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
xtsonic_open() doesn't check sonic_open() return code. If it is error
we must free requested IRQ.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macsonic_open() doesn't check sonic_open() return code. If it is error
we must free requested IRQs.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
jazzsonic_open() doesn't check sonic_open() return code. If it is error
we must free requested IRQ.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tc35815_init_one() fails we must unmap mapped regions.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up TX Queue Host Flow Control to cause an Egress Queue Status Update to
be generated when we run out of TX Queue Descriptors. This will, in turn,
allow us to restart a stopped TX Queue.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since some of xxx_register_driver() can return error we must unregister
already registered drivers.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AR5008+ and AR9003 currently use two separate implementations of the
ath9k_hw_loadnf function. There are three main differences:
- PHY registers for AR9003 are different
- AR9003 always uses 3 chains, earlier versions are more selective
- The AR9003 variant contains a fix for NF load timeouts
This patch merges the two implementations into one, storing the
register array in the ath_hw struct. The fix for NF load timeouts is
not just relevant for AR9003, but also important for earlier hardware,
so it's better to just keep one common implementation.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Occasionally the hardware can send out tx status information with the wrong
TID. In that case, the BA status cannot be trusted and the aggregate
must be retransmitted.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the receive path gets stuck, a full hardware reset is necessary to
recover from it. If this happens during a scan, the whole scan might fail,
as each channel change bypasses the full reset sequence.
Fix this by resetting the fast channel change flag if stopping the
receive path fails.
This will reduce the number of error messages that look like this:
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x40000020
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PDADC values were only generated for values surrounding the target
index, however not for the target index itself, leading to a minor
error in the generated curve.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9285, the antenna switch configuration register uses more than just
16 bits. Because of an arbitrary mask applied to the EEPROM value that
stores this configuration, diversity was broken in some cases, leading
to a significant degradation in signal strength.
Fix this by changing the callback to return a 32 bit value and remove
the arbitrary mask.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callback functions are gathered in rt2x00dev->ops except
for the callback functions which are used in rt2800lib to
acces rt2800pci/usb.
Move the priv pointer from rt2x00dev to rt2x00dev->ops and
rename it to drv to make it obvious that it is the driver callback
structure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Large parts of the firmware initialization are shared
between rt2800pci and rt2800usb. Move this code into
rt2800lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently rt2x00 uses the TSF_SYNC_BEACON mode for all beaconing
interface types. However, TSF_SYNC_BEACON is meant for IBSS networks and
thus implements TSF merging in the hardware. Rename TSF_SYNC_BEACON to
TSF_SYNC_ADHOC to better express its purpose and introduce the missing
TSF sync mode TSF_SYNC_AP_NONE which should be used for beaconing modes
that don't need TSF merging.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Activating the TBTT interrupt when a beacon interval of 0 is configured
results in an interrupt storm causing the machine to hang. Hence,
initialize the beacon interval to a reasonable default of 100TUs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the set_tim callback without managing the DTIM count and the
broad- and multicast buffering in hw, fw or the driver results in wrong
DTIM count values being sent out in beacons. Since all PCI drivers
fetch new beacons periodically and hence get an updated TIM we can just
remove the set_tim callback from these.
The rt2x00 USB drivers don't update the beacon periodically and thus
rely on the set_tim callback to get a correct TIM for beacon
transmission. USB devices still suffer from the DTIM count being wrong
under some circumstances but removing the set_tim callback from these
would cause more harm then good.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use separate mac80211_ops for rt2800pci and rt2800usb in preparation
for further fixes. This shouldn't introduce functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updating the beacon on pre tbtt instead of beacondone allows much lower
latency in regard to TIM updates. Hence, use the pre tbtt interrupt for
updating the beacon in rt2800pci (older devices don't provide a pre tbtt
interrupt).
Also, add a new driver flag to indicate if a driver has pre tbtt support
or not and implement the according behavior in rt2x00lib.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although mac80211 buffers broad- and mutlicast frames for us in AP mode
we still have to send them out after a DTIM beacon. Implement this
behavior by sending out the buffered frames when the beacondone
interrupt is processed.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since all rt2x00 PCI drivers use threaded interrupts now we don't need
to schedule a work just to update the beacon. The only place where the
beacon still gets updated in atomic context is from the set_tim
callback. Hence, move the work scheduling there.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use threaded interrupts for all rt2x00 PCI devices.
This has several generic advantages:
- Reduce the time we spend in hard irq context
- Use non-atmic mac80211 functions for rx/tx
Furthermore implementing broad- and multicast buffering will be
much easier in process context while maintaining low latency and
updating the beacon just before transmission (pre tbtt interrupt)
can also be done in process context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800_write_beacon is the only function which uses
EXPORT_SYMBOL instead of EXPORT_SYMBOL_GPL. All symbols
in rt2x00 should however use the GPL restricted export.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement watchdog monitoring for USB devices (PCI support can
be added later). This will determine if URBs being uploaded to
the hardware are actually returning. Both rt2500usb and rt2800usb
have shown that URBs being uploaded can remain hanging without
being released by the hardware.
By using this watchdog, a queue can be reset when this occurs.
For rt2800usb it has been tested that the connection is preserved
even though this interruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
