diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt new file mode 100644 index 000000000000..2e57a33e9029 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -0,0 +1,128 @@ +Adaptive Body Bias(ABB) SoC internal LDO regulator for Texas Instruments SoCs + +Required Properties: +- compatible: Should be one of: + - "ti,abb-v1" for older SoCs like OMAP3 + - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5 +- reg: Address and length of the register set for the device. It contains + the information of registers in the same order as described by reg-names +- reg-names: Should contain the reg names + - "base-address" - contains base address of ABB module + - "int-address" - contains address of interrupt register for ABB module + (also see Optional properties) +- #address-cell: should be 0 +- #size-cell: should be 0 +- clocks: should point to the clock node used by ABB module +- ti,settling-time: Settling time in uSecs from SoC documentation for ABB module + to settle down(target time for SR2_WTCNT_VALUE). +- ti,clock-cycles: SoC specific data about count of system ti,clock-cycles used for + computing settling time from SoC Documentation for ABB module(clock + cycles for SR2_WTCNT_VALUE). +- ti,tranxdone-status-mask: Mask to the int-register to write-to-clear mask + indicating LDO tranxdone (operation complete). +- ti,abb_info: An array of 6-tuples u32 items providing information about ABB + configuration needed per operational voltage of the device. + Each item consists of the following in the same order: + volt: voltage in uV - Only used to index ABB information. + ABB mode: one of the following: + 0-bypass + 1-Forward Body Bias(FBB) + 3-Reverse Body Bias(RBB) + efuse: (see Optional properties) + RBB enable efuse Mask: (See Optional properties) + FBB enable efuse Mask: (See Optional properties) + Vset value efuse Mask: (See Optional properties) + + NOTE: If more than 1 entry is present, then regulator is setup to change + voltage, allowing for various modes to be selected indexed off + the regulator. Further, ABB LDOs are considered always-on by + default. + +Optional Properties: +- reg-names: In addition to the required properties, the following are optional + - "efuse-address" - Contains efuse base address used to pick up ABB info. + - "ldo-address" - Contains address of ABB LDO overide register address. + "efuse-address" is required for this. +- ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override + register to provide override vset value. +- ti,ldovbb-override-mask - Required if ldo-address is set, mask for LDO + override register to enable override vset value. +- ti,abb_opp_sel: Addendum to the description in required properties + efuse: Mandatory if 'efuse-address' register is defined. Provides offset + from efuse-address to pick up ABB characteristics. Set to 0 if + 'efuse-address' is not defined. + RBB enable efuse Mask: Optional if 'efuse-address' register is defined. + 'ABB mode' is force set to RBB mode if value at "efuse-address" + + efuse maps to RBB mask. Set to 0 to ignore this. + FBB enable efuse Mask: Optional if 'efuse-address' register is defined. + 'ABB mode' is force set to FBB mode if value at "efuse-address" + + efuse maps to FBB mask (valid only if RBB mask does not match) + Set to 0 to ignore this. + Vset value efuse Mask: Mandatory if ldo-address is set. Picks up from + efuse the value to set in 'ti,ldovbb-vset-mask' at ldo-address. + +Example #1: Simplest configuration (no efuse data, hard coded ABB table): +abb_x: regulator-abb-x { + compatible = "ti,abb-v1"; + regulator-name = "abb_x"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x483072f0 0x8>, <0x48306818 0x4>; + reg-names = "base-address", "int-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sysclk>; + ti,settling-time = <30>; + ti,clock-cycles = <8>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 1012500 0 0 0 0 0 /* Bypass */ + 1200000 3 0 0 0 0 /* RBB mandatory */ + 1320000 1 0 0 0 0 /* FBB mandatory */ + >; +}; + +Example #2: Efuse bits contain ABB mode setting (no LDO override capability) +abb_y: regulator-abb-y { + compatible = "ti,abb-v2"; + regulator-name = "abb_y"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, <0x4A002268 0x8>; + reg-names = "base-address", "int-address", "efuse-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sysclk>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 975000 0 0 0 0 0 /* Bypass */ + 1012500 0 0 0x40000 0 0 /* RBB optional */ + 1200000 0 0x4 0 0x40000 0 /* FBB optional */ + 1320000 1 0 0 0 0 /* FBB mandatory */ + >; +}; + +Example #3: Efuse bits contain ABB mode setting and LDO override capability +abb_z: regulator-abb-z { + compatible = "ti,abb-v2"; + regulator-name = "abb_z"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>, + <0x4a002194 0x8>, <0x4ae0C314 0x4>; + reg-names = "base-address", "int-address", + "efuse-address", "ldo-address"; + ti,tranxdone-status-mask = <0x8000000>; + /* LDOVBBMM_MUX_CTRL */ + ti,ldovbb-override-mask = <0x400>; + /* LDOVBBMM_VSET_OUT */ + ti,ldovbb-vset-mask = <0x1F>; + clocks = <&sysclk>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 975000 0 0 0 0 0 /* Bypass */ + 1200000 0 0x4 0 0x40000 0x1f00 /* FBB optional, vset */ + >; +}; diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig index 8bb26446037e..9296425103ef 100644 --- a/drivers/regulator/Kconfig +++ b/drivers/regulator/Kconfig @@ -472,6 +472,16 @@ config REGULATOR_TWL4030 This driver supports the voltage regulators provided by this family of companion chips. +config REGULATOR_TI_ABB + bool "TI Adaptive Body Bias on-chip LDO" + depends on ARCH_OMAP + help + Select this option to support Texas Instruments' on-chip Adaptive Body + Bias (ABB) LDO regulators. It is recommended that this option be + enabled on required TI SoC. Certain Operating Performance Points + on TI SoCs may be unstable without enabling this as it provides + device specific optimized bias to allow/optimize functionality. + config REGULATOR_VEXPRESS tristate "Versatile Express regulators" depends on VEXPRESS_CONFIG diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index 47a34ff88f98..95350e890973 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -63,6 +63,7 @@ obj-$(CONFIG_REGULATOR_TPS65910) += tps65910-regulator.o obj-$(CONFIG_REGULATOR_TPS65912) += tps65912-regulator.o obj-$(CONFIG_REGULATOR_TPS80031) += tps80031-regulator.o obj-$(CONFIG_REGULATOR_TWL4030) += twl-regulator.o +obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o obj-$(CONFIG_REGULATOR_VEXPRESS) += vexpress.o obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o obj-$(CONFIG_REGULATOR_WM831X) += wm831x-isink.o diff --git a/drivers/regulator/ti-abb-regulator.c b/drivers/regulator/ti-abb-regulator.c new file mode 100644 index 000000000000..c1870ea64939 --- /dev/null +++ b/drivers/regulator/ti-abb-regulator.c @@ -0,0 +1,912 @@ +/* + * Texas Instruments SoC Adaptive Body Bias(ABB) Regulator + * + * Copyright (C) 2011 Texas Instruments, Inc. + * Mike Turquette + * + * Copyright (C) 2012-2013 Texas Instruments, Inc. + * Andrii Tseglytskyi + * Nishanth Menon + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* + * ABB LDO operating states: + * NOMINAL_OPP: bypasses the ABB LDO + * FAST_OPP: sets ABB LDO to Forward Body-Bias + * SLOW_OPP: sets ABB LDO to Reverse Body-Bias + */ +#define TI_ABB_NOMINAL_OPP 0 +#define TI_ABB_FAST_OPP 1 +#define TI_ABB_SLOW_OPP 3 + +/** + * struct ti_abb_info - ABB information per voltage setting + * @opp_sel: one of TI_ABB macro + * @vset: (optional) vset value that LDOVBB needs to be overriden with. + * + * Array of per voltage entries organized in the same order as regulator_desc's + * volt_table list. (selector is used to index from this array) + */ +struct ti_abb_info { + u32 opp_sel; + u32 vset; +}; + +/** + * struct ti_abb_reg - Register description for ABB block + * @setup_reg: setup register offset from base + * @control_reg: control register offset from base + * @sr2_wtcnt_value_mask: setup register- sr2_wtcnt_value mask + * @fbb_sel_mask: setup register- FBB sel mask + * @rbb_sel_mask: setup register- RBB sel mask + * @sr2_en_mask: setup register- enable mask + * @opp_change_mask: control register - mask to trigger LDOVBB change + * @opp_sel_mask: control register - mask for mode to operate + */ +struct ti_abb_reg { + u32 setup_reg; + u32 control_reg; + + /* Setup register fields */ + u32 sr2_wtcnt_value_mask; + u32 fbb_sel_mask; + u32 rbb_sel_mask; + u32 sr2_en_mask; + + /* Control register fields */ + u32 opp_change_mask; + u32 opp_sel_mask; +}; + +/** + * struct ti_abb - ABB instance data + * @rdesc: regulator descriptor + * @clk: clock(usually sysclk) supplying ABB block + * @base: base address of ABB block + * @int_base: interrupt register base address + * @efuse_base: (optional) efuse base address for ABB modes + * @ldo_base: (optional) LDOVBB vset override base address + * @regs: pointer to struct ti_abb_reg for ABB block + * @txdone_mask: mask on int_base for tranxdone interrupt + * @ldovbb_override_mask: mask to ldo_base for overriding default LDO VBB + * vset with value from efuse + * @ldovbb_vset_mask: mask to ldo_base for providing the VSET override + * @info: array to per voltage ABB configuration + * @current_info_idx: current index to info + * @settling_time: SoC specific settling time for LDO VBB + */ +struct ti_abb { + struct regulator_desc rdesc; + struct clk *clk; + void __iomem *base; + void __iomem *int_base; + void __iomem *efuse_base; + void __iomem *ldo_base; + + const struct ti_abb_reg *regs; + u32 txdone_mask; + u32 ldovbb_override_mask; + u32 ldovbb_vset_mask; + + struct ti_abb_info *info; + int current_info_idx; + + u32 settling_time; +}; + +/** + * ti_abb_rmw() - handy wrapper to set specific register bits + * @mask: mask for register field + * @value: value shifted to mask location and written + * @offset: offset of register + * @base: base address + * + * Return: final register value (may be unused) + */ +static inline u32 ti_abb_rmw(u32 mask, u32 value, u32 offset, + void __iomem *base) +{ + u32 val; + + val = readl(base + offset); + val &= ~mask; + val |= (value << __ffs(mask)) & mask; + writel(val, base + offset); + + return val; +} + +/** + * ti_abb_check_txdone() - handy wrapper to check ABB tranxdone status + * @abb: pointer to the abb instance + * + * Return: true or false + */ +static inline bool ti_abb_check_txdone(const struct ti_abb *abb) +{ + return !!(readl(abb->int_base) & abb->txdone_mask); +} + +/** + * ti_abb_clear_txdone() - handy wrapper to clear ABB tranxdone status + * @abb: pointer to the abb instance + */ +static inline void ti_abb_clear_txdone(const struct ti_abb *abb) +{ + writel(abb->txdone_mask, abb->int_base); +}; + +/** + * ti_abb_wait_tranx() - waits for ABB tranxdone event + * @dev: device + * @abb: pointer to the abb instance + * + * Return: 0 on success or -ETIMEDOUT if the event is not cleared on time. + */ +static int ti_abb_wait_txdone(struct device *dev, struct ti_abb *abb) +{ + int timeout = 0; + bool status; + + while (timeout++ <= abb->settling_time) { + status = ti_abb_check_txdone(abb); + if (status) + break; + + udelay(1); + } + + if (timeout > abb->settling_time) { + dev_warn_ratelimited(dev, + "%s:TRANXDONE timeout(%duS) int=0x%08x\n", + __func__, timeout, readl(abb->int_base)); + return -ETIMEDOUT; + } + + return 0; +} + +/** + * ti_abb_clear_all_txdone() - clears ABB tranxdone event + * @dev: device + * @abb: pointer to the abb instance + * + * Return: 0 on success or -ETIMEDOUT if the event is not cleared on time. + */ +static int ti_abb_clear_all_txdone(struct device *dev, const struct ti_abb *abb) +{ + int timeout = 0; + bool status; + + while (timeout++ <= abb->settling_time) { + ti_abb_clear_txdone(abb); + + status = ti_abb_check_txdone(abb); + if (!status) + break; + + udelay(1); + } + + if (timeout > abb->settling_time) { + dev_warn_ratelimited(dev, + "%s:TRANXDONE timeout(%duS) int=0x%08x\n", + __func__, timeout, readl(abb->int_base)); + return -ETIMEDOUT; + } + + return 0; +} + +/** + * ti_abb_program_ldovbb() - program LDOVBB register for override value + * @dev: device + * @abb: pointer to the abb instance + * @info: ABB info to program + */ +static void ti_abb_program_ldovbb(struct device *dev, const struct ti_abb *abb, + struct ti_abb_info *info) +{ + u32 val; + + val = readl(abb->ldo_base); + /* clear up previous values */ + val &= ~(abb->ldovbb_override_mask | abb->ldovbb_vset_mask); + + switch (info->opp_sel) { + case TI_ABB_SLOW_OPP: + case TI_ABB_FAST_OPP: + val |= abb->ldovbb_override_mask; + val |= info->vset << __ffs(abb->ldovbb_vset_mask); + break; + } + + writel(val, abb->ldo_base); +} + +/** + * ti_abb_set_opp() - Setup ABB and LDO VBB for required bias + * @rdev: regulator device + * @abb: pointer to the abb instance + * @info: ABB info to program + * + * Return: 0 on success or appropriate error value when fails + */ +static int ti_abb_set_opp(struct regulator_dev *rdev, struct ti_abb *abb, + struct ti_abb_info *info) +{ + const struct ti_abb_reg *regs = abb->regs; + struct device *dev = &rdev->dev; + int ret; + + ret = ti_abb_clear_all_txdone(dev, abb); + if (ret) + goto out; + + ti_abb_rmw(regs->fbb_sel_mask | regs->rbb_sel_mask, 0, regs->setup_reg, + abb->base); + + switch (info->opp_sel) { + case TI_ABB_SLOW_OPP: + ti_abb_rmw(regs->rbb_sel_mask, 1, regs->setup_reg, abb->base); + break; + case TI_ABB_FAST_OPP: + ti_abb_rmw(regs->fbb_sel_mask, 1, regs->setup_reg, abb->base); + break; + } + + /* program next state of ABB ldo */ + ti_abb_rmw(regs->opp_sel_mask, info->opp_sel, regs->control_reg, + abb->base); + + /* program LDO VBB vset override if needed */ + if (abb->ldo_base) + ti_abb_program_ldovbb(dev, abb, info); + + /* Initiate ABB ldo change */ + ti_abb_rmw(regs->opp_change_mask, 1, regs->control_reg, abb->base); + + /* Wait for ABB LDO to complete transition to new Bias setting */ + ret = ti_abb_wait_txdone(dev, abb); + if (ret) + goto out; + + ret = ti_abb_clear_all_txdone(dev, abb); + if (ret) + goto out; + +out: + return ret; +} + +/** + * ti_abb_set_voltage_sel() - regulator accessor function to set ABB LDO + * @rdev: regulator device + * @sel: selector to index into required ABB LDO settings (maps to + * regulator descriptor's volt_table) + * + * Return: 0 on success or appropriate error value when fails + */ +static int ti_abb_set_voltage_sel(struct regulator_dev *rdev, unsigned sel) +{ + const struct regulator_desc *desc = rdev->desc; + struct ti_abb *abb = rdev_get_drvdata(rdev); + struct device *dev = &rdev->dev; + struct ti_abb_info *info, *oinfo; + int ret = 0; + + if (!abb) { + dev_err_ratelimited(dev, "%s: No regulator drvdata\n", + __func__); + return -ENODEV; + } + + if (!desc->n_voltages || !abb->info) { + dev_err_ratelimited(dev, + "%s: No valid voltage table entries?\n", + __func__); + return -EINVAL; + } + + if (sel >= desc->n_voltages) { + dev_err(dev, "%s: sel idx(%d) >= n_voltages(%d)\n", __func__, + sel, desc->n_voltages); + return -EINVAL; + } + + /* If we are in the same index as we were, nothing to do here! */ + if (sel == abb->current_info_idx) { + dev_dbg(dev, "%s: Already at sel=%d\n", __func__, sel); + return ret; + } + + /* If data is exactly the same, then just update index, no change */ + info = &abb->info[sel]; + oinfo = &abb->info[abb->current_info_idx]; + if (!memcmp(info, oinfo, sizeof(*info))) { + dev_dbg(dev, "%s: Same data new idx=%d, old idx=%d\n", __func__, + sel, abb->current_info_idx); + goto out; + } + + ret = ti_abb_set_opp(rdev, abb, info); + +out: + if (!ret) + abb->current_info_idx = sel; + else + dev_err_ratelimited(dev, + "%s: Volt[%d] idx[%d] mode[%d] Fail(%d)\n", + __func__, desc->volt_table[sel], sel, + info->opp_sel, ret); + return ret; +} + +/** + * ti_abb_get_voltage_sel() - Regulator accessor to get current ABB LDO setting + * @rdev: regulator device + * + * Return: 0 on success or appropriate error value when fails + */ +static int ti_abb_get_voltage_sel(struct regulator_dev *rdev) +{ + const struct regulator_desc *desc = rdev->desc; + struct ti_abb *abb = rdev_get_drvdata(rdev); + struct device *dev = &rdev->dev; + + if (!abb) { + dev_err_ratelimited(dev, "%s: No regulator drvdata\n", + __func__); + return -ENODEV; + } + + if (!desc->n_voltages || !abb->info) { + dev_err_ratelimited(dev, + "%s: No valid voltage table entries?\n", + __func__); + return -EINVAL; + } + + if (abb->current_info_idx > (int)desc->n_voltages) { + dev_err(dev, "%s: Corrupted data? idx(%d) > n_voltages(%d)\n", + __func__, abb->current_info_idx, desc->n_voltages); + return -EINVAL; + } + + return abb->current_info_idx; +} + +/** + * ti_abb_init_timings() - setup ABB clock timing for the current platform + * @dev: device + * @abb: pointer to the abb instance + * + * Return: 0 if timing is updated, else returns error result. + */ +static int ti_abb_init_timings(struct device *dev, struct ti_abb *abb) +{ + u32 clock_cycles; + u32 clk_rate, sr2_wt_cnt_val, cycle_rate; + const struct ti_abb_reg *regs = abb->regs; + int ret; + char *pname = "ti,settling-time"; + + /* read device tree properties */ + ret = of_property_read_u32(dev->of_node, pname, &abb->settling_time); + if (ret) { + dev_err(dev, "Unable to get property '%s'(%d)\n", pname, ret); + return ret; + } + + /* ABB LDO cannot be settle in 0 time */ + if (!abb->settling_time) { + dev_err(dev, "Invalid property:'%s' set as 0!\n", pname); + return -EINVAL; + } + + pname = "ti,clock-cycles"; + ret = of_property_read_u32(dev->of_node, pname, &clock_cycles); + if (ret) { + dev_err(dev, "Unable to get property '%s'(%d)\n", pname, ret); + return ret; + } + /* ABB LDO cannot be settle in 0 clock cycles */ + if (!clock_cycles) { + dev_err(dev, "Invalid property:'%s' set as 0!\n", pname); + return -EINVAL; + } + + abb->clk = devm_clk_get(dev, NULL); + if (IS_ERR(abb->clk)) { + ret = PTR_ERR(abb->clk); + dev_err(dev, "%s: Unable to get clk(%d)\n", __func__, ret); + return ret; + } + + /* + * SR2_WTCNT_VALUE is the settling time for the ABB ldo after a + * transition and must be programmed with the correct time at boot. + * The value programmed into the register is the number of SYS_CLK + * clock cycles that match a given wall time profiled for the ldo. + * This value depends on: + * settling time of ldo in micro-seconds (varies per OMAP family) + * # of clock cycles per SYS_CLK period (varies per OMAP family) + * the SYS_CLK frequency in MHz (varies per board) + * The formula is: + * + * ldo settling time (in micro-seconds) + * SR2_WTCNT_VALUE = ------------------------------------------ + * (# system clock cycles) * (sys_clk period) + * + * Put another way: + * + * SR2_WTCNT_VALUE = settling time / (# SYS_CLK cycles / SYS_CLK rate)) + * + * To avoid dividing by zero multiply both "# clock cycles" and + * "settling time" by 10 such that the final result is the one we want. + */ + + /* Convert SYS_CLK rate to MHz & prevent divide by zero */ + clk_rate = DIV_ROUND_CLOSEST(clk_get_rate(abb->clk), 1000000); + + /* Calculate cycle rate */ + cycle_rate = DIV_ROUND_CLOSEST(clock_cycles * 10, clk_rate); + + /* Calulate SR2_WTCNT_VALUE */ + sr2_wt_cnt_val = DIV_ROUND_CLOSEST(abb->settling_time * 10, cycle_rate); + + dev_dbg(dev, "%s: Clk_rate=%ld, sr2_cnt=0x%08x\n", __func__, + clk_get_rate(abb->clk), sr2_wt_cnt_val); + + ti_abb_rmw(regs->sr2_wtcnt_value_mask, sr2_wt_cnt_val, regs->setup_reg, + abb->base); + + return 0; +} + +/** + * ti_abb_init_table() - Initialize ABB table from device tree + * @dev: device + * @abb: pointer to the abb instance + * @rinit_data: regulator initdata + * + * Return: 0 on success or appropriate error value when fails + */ +static int ti_abb_init_table(struct device *dev, struct ti_abb *abb, + struct regulator_init_data *rinit_data) +{ + struct ti_abb_info *info; + const struct property *prop; + const __be32 *abb_info; + const u32 num_values = 6; + char *pname = "ti,abb_info"; + u32 num_entries, i; + unsigned int *volt_table; + int min_uV = INT_MAX, max_uV = 0; + struct regulation_constraints *c = &rinit_data->constraints; + + prop = of_find_property(dev->of_node, pname, NULL); + if (!prop) { + dev_err(dev, "No '%s' property?\n", pname); + return -ENODEV; + } + + if (!prop->value) { + dev_err(dev, "Empty '%s' property?\n", pname); + return -ENODATA; + } + + /* + * Each abb_info is a set of n-tuple, where n is num_values, consisting + * of voltage and a set of detection logic for ABB information for that + * voltage to apply. + */ + num_entries = prop->length / sizeof(u32); + if (!num_entries || (num_entries % num_values)) { + dev_err(dev, "All '%s' list entries need %d vals\n", pname, + num_values); + return -EINVAL; + } + num_entries /= num_values; + + info = devm_kzalloc(dev, sizeof(*info) * num_entries, GFP_KERNEL); + if (!info) { + dev_err(dev, "Can't allocate info table for '%s' property\n", + pname); + return -ENOMEM; + } + abb->info = info; + + volt_table = devm_kzalloc(dev, sizeof(unsigned int) * num_entries, + GFP_KERNEL); + if (!volt_table) { + dev_err(dev, "Can't allocate voltage table for '%s' property\n", + pname); + return -ENOMEM; + } + + abb->rdesc.n_voltages = num_entries; + abb->rdesc.volt_table = volt_table; + /* We do not know where the OPP voltage is at the moment */ + abb->current_info_idx = -EINVAL; + + abb_info = prop->value; + for (i = 0; i < num_entries; i++, info++, volt_table++) { + u32 efuse_offset, rbb_mask, fbb_mask, vset_mask; + u32 efuse_val; + + /* NOTE: num_values should equal to entries picked up here */ + *volt_table = be32_to_cpup(abb_info++); + info->opp_sel = be32_to_cpup(abb_info++); + efuse_offset = be32_to_cpup(abb_info++); + rbb_mask = be32_to_cpup(abb_info++); + fbb_mask = be32_to_cpup(abb_info++); + vset_mask = be32_to_cpup(abb_info++); + + dev_dbg(dev, + "[%d]v=%d ABB=%d ef=0x%x rbb=0x%x fbb=0x%x vset=0x%x\n", + i, *volt_table, info->opp_sel, efuse_offset, rbb_mask, + fbb_mask, vset_mask); + + /* Find min/max for voltage set */ + if (min_uV > *volt_table) + min_uV = *volt_table; + if (max_uV < *volt_table) + max_uV = *volt_table; + + if (!abb->efuse_base) { + /* Ignore invalid data, but warn to help cleanup */ + if (efuse_offset || rbb_mask || fbb_mask || vset_mask) + dev_err(dev, "prop '%s': v=%d,bad efuse/mask\n", + pname, *volt_table); + goto check_abb; + } + + efuse_val = readl(abb->efuse_base + efuse_offset); + + /* Use ABB recommendation from Efuse */ + if (efuse_val & rbb_mask) + info->opp_sel = TI_ABB_SLOW_OPP; + else if (efuse_val & fbb_mask) + info->opp_sel = TI_ABB_FAST_OPP; + else if (rbb_mask || fbb_mask) + info->opp_sel = TI_ABB_NOMINAL_OPP; + + dev_dbg(dev, + "[%d]v=%d efusev=0x%x final ABB=%d\n", + i, *volt_table, efuse_val, info->opp_sel); + + /* Use recommended Vset bits from Efuse */ + if (!abb->ldo_base) { + if (vset_mask) + dev_err(dev, "prop'%s':v=%d vst=%x LDO base?\n", + pname, *volt_table, vset_mask); + continue; + } + info->vset = efuse_val & vset_mask >> __ffs(vset_mask); + dev_dbg(dev, "[%d]v=%d vset=%x\n", i, *volt_table, info->vset); +check_abb: + switch (info->opp_sel) { + case TI_ABB_NOMINAL_OPP: + case TI_ABB_FAST_OPP: + case TI_ABB_SLOW_OPP: + /* Valid values */ + break; + default: + dev_err(dev, "%s:[%d]v=%d, ABB=%d is invalid! Abort!\n", + __func__, i, *volt_table, info->opp_sel); + return -EINVAL; + } + } + + /* Setup the min/max voltage constraints from the supported list */ + c->min_uV = min_uV; + c->max_uV = max_uV; + + return 0; +} + +static struct regulator_ops ti_abb_reg_ops = { + .list_voltage = regulator_list_voltage_table, + + .set_voltage_sel = ti_abb_set_voltage_sel, + .get_voltage_sel = ti_abb_get_voltage_sel, +}; + +/* Default ABB block offsets, IF this changes in future, create new one */ +static const struct ti_abb_reg abb_regs_v1 = { + /* WARNING: registers are wrongly documented in TRM */ + .setup_reg = 0x04, + .control_reg = 0x00, + + .sr2_wtcnt_value_mask = (0xff << 8), + .fbb_sel_mask = (0x01 << 2), + .rbb_sel_mask = (0x01 << 1), + .sr2_en_mask = (0x01 << 0), + + .opp_change_mask = (0x01 << 2), + .opp_sel_mask = (0x03 << 0), +}; + +static const struct ti_abb_reg abb_regs_v2 = { + .setup_reg = 0x00, + .control_reg = 0x04, + + .sr2_wtcnt_value_mask = (0xff << 8), + .fbb_sel_mask = (0x01 << 2), + .rbb_sel_mask = (0x01 << 1), + .sr2_en_mask = (0x01 << 0), + + .opp_change_mask = (0x01 << 2), + .opp_sel_mask = (0x03 << 0), +}; + +static const struct of_device_id ti_abb_of_match[] = { + {.compatible = "ti,abb-v1", .data = &abb_regs_v1}, + {.compatible = "ti,abb-v2", .data = &abb_regs_v2}, + { }, +}; + +MODULE_DEVICE_TABLE(of, ti_abb_of_match); + +/** + * ti_abb_probe() - Initialize an ABB ldo instance + * @pdev: ABB platform device + * + * Initializes an individual ABB LDO for required Body-Bias. ABB is used to + * addional bias supply to SoC modules for power savings or mandatory stability + * configuration at certain Operating Performance Points(OPPs). + * + * Return: 0 on success or appropriate error value when fails + */ +static int ti_abb_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + const struct of_device_id *match; + struct resource *res; + struct ti_abb *abb; + struct regulator_init_data *initdata = NULL; + struct regulator_dev *rdev = NULL; + struct regulator_desc *desc; + struct regulation_constraints *c; + struct regulator_config config = { }; + char *pname; + int ret = 0; + + match = of_match_device(ti_abb_of_match, dev); + if (!match) { + /* We do not expect this to happen */ + ret = -ENODEV; + dev_err(dev, "%s: Unable to match device\n", __func__); + goto err; + } + if (!match->data) { + ret = -EINVAL; + dev_err(dev, "%s: Bad data in match\n", __func__); + goto err; + } + + abb = devm_kzalloc(dev, sizeof(struct ti_abb), GFP_KERNEL); + if (!abb) { + dev_err(dev, "%s: Unable to allocate ABB struct\n", __func__); + ret = -ENOMEM; + goto err; + } + abb->regs = match->data; + + /* Map ABB resources */ + pname = "base-address"; + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); + if (!res) { + dev_err(dev, "Missing '%s' IO resource\n", pname); + ret = -ENODEV; + goto err; + } + abb->base = devm_request_and_ioremap(dev, res); + if (!abb->base) { + dev_err(dev, "Unable to map '%s'\n", pname); + ret = -ENOMEM; + goto err; + } + + pname = "int-address"; + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); + if (!res) { + dev_err(dev, "Missing '%s' IO resource\n", pname); + ret = -ENODEV; + goto err; + } + /* + * We may have shared interrupt register offsets which are + * write-1-to-clear between domains ensuring exclusivity. + */ + abb->int_base = devm_ioremap_nocache(dev, res->start, + resource_size(res)); + if (!abb->int_base) { + dev_err(dev, "Unable to map '%s'\n", pname); + ret = -ENOMEM; + goto err; + } + + /* Map Optional resources */ + pname = "efuse-address"; + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); + if (!res) { + dev_dbg(dev, "Missing '%s' IO resource\n", pname); + ret = -ENODEV; + goto skip_opt; + } + + /* + * We may have shared efuse register offsets which are read-only + * between domains + */ + abb->efuse_base = devm_ioremap_nocache(dev, res->start, + resource_size(res)); + if (!abb->efuse_base) { + dev_err(dev, "Unable to map '%s'\n", pname); + ret = -ENOMEM; + goto err; + } + + pname = "ldo-address"; + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); + if (!res) { + dev_dbg(dev, "Missing '%s' IO resource\n", pname); + ret = -ENODEV; + goto skip_opt; + } + abb->ldo_base = devm_request_and_ioremap(dev, res); + if (!abb->ldo_base) { + dev_err(dev, "Unable to map '%s'\n", pname); + ret = -ENOMEM; + goto err; + } + + /* IF ldo_base is set, the following are mandatory */ + pname = "ti,ldovbb-override-mask"; + ret = + of_property_read_u32(pdev->dev.of_node, pname, + &abb->ldovbb_override_mask); + if (ret) { + dev_err(dev, "Missing '%s' (%d)\n", pname, ret); + goto err; + } + if (!abb->ldovbb_override_mask) { + dev_err(dev, "Invalid property:'%s' set as 0!\n", pname); + ret = -EINVAL; + goto err; + } + + pname = "ti,ldovbb-vset-mask"; + ret = + of_property_read_u32(pdev->dev.of_node, pname, + &abb->ldovbb_vset_mask); + if (ret) { + dev_err(dev, "Missing '%s' (%d)\n", pname, ret); + goto err; + } + if (!abb->ldovbb_vset_mask) { + dev_err(dev, "Invalid property:'%s' set as 0!\n", pname); + ret = -EINVAL; + goto err; + } + +skip_opt: + pname = "ti,tranxdone-status-mask"; + ret = + of_property_read_u32(pdev->dev.of_node, pname, + &abb->txdone_mask); + if (ret) { + dev_err(dev, "Missing '%s' (%d)\n", pname, ret); + goto err; + } + if (!abb->txdone_mask) { + dev_err(dev, "Invalid property:'%s' set as 0!\n", pname); + ret = -EINVAL; + goto err; + } + + initdata = of_get_regulator_init_data(dev, pdev->dev.of_node); + if (!initdata) { + ret = -ENOMEM; + dev_err(dev, "%s: Unable to alloc regulator init data\n", + __func__); + goto err; + } + + /* init ABB opp_sel table */ + ret = ti_abb_init_table(dev, abb, initdata); + if (ret) + goto err; + + /* init ABB timing */ + ret = ti_abb_init_timings(dev, abb); + if (ret) + goto err; + + desc = &abb->rdesc; + desc->name = dev_name(dev); + desc->owner = THIS_MODULE; + desc->type = REGULATOR_VOLTAGE; + desc->ops = &ti_abb_reg_ops; + + c = &initdata->constraints; + if (desc->n_voltages > 1) + c->valid_ops_mask |= REGULATOR_CHANGE_VOLTAGE; + c->always_on = true; + + config.dev = dev; + config.init_data = initdata; + config.driver_data = abb; + config.of_node = pdev->dev.of_node; + + rdev = regulator_register(desc, &config); + if (IS_ERR(rdev)) { + ret = PTR_ERR(rdev); + dev_err(dev, "%s: failed to register regulator(%d)\n", + __func__, ret); + goto err; + } + platform_set_drvdata(pdev, rdev); + + /* Enable the ldo if not already done by bootloader */ + ti_abb_rmw(abb->regs->sr2_en_mask, 1, abb->regs->setup_reg, abb->base); + + return 0; + +err: + dev_err(dev, "%s: Failed to initialize(%d)\n", __func__, ret); + return ret; +} + +/** + * ti_abb_remove() - cleanups + * @pdev: ABB platform device + * + * Return: 0 + */ +static int ti_abb_remove(struct platform_device *pdev) +{ + struct regulator_dev *rdev = platform_get_drvdata(pdev); + + regulator_unregister(rdev); + return 0; +} + +MODULE_ALIAS("platform:ti_abb"); + +static struct platform_driver ti_abb_driver = { + .probe = ti_abb_probe, + .remove = ti_abb_remove, + .driver = { + .name = "ti_abb", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(ti_abb_of_match), + }, +}; +module_platform_driver(ti_abb_driver); + +MODULE_DESCRIPTION("Texas Instruments ABB LDO regulator driver"); +MODULE_AUTHOR("Texas Instruments Inc."); +MODULE_LICENSE("GPL v2");