linux/drivers/hwmon/bt1-pvt.c

1179 lines
30 KiB
C
Raw Normal View History

hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2020 BAIKAL ELECTRONICS, JSC
*
* Authors:
* Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
* Serge Semin <Sergey.Semin@baikalelectronics.ru>
*
* Baikal-T1 Process, Voltage, Temperature sensor driver
*/
#include <linux/bitfield.h>
#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/completion.h>
#include <linux/delay.h>
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
#include <linux/device.h>
#include <linux/hwmon-sysfs.h>
#include <linux/hwmon.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/ktime.h>
#include <linux/limits.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/polynomial.h>
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
#include <linux/seqlock.h>
#include <linux/sysfs.h>
#include <linux/types.h>
#include "bt1-pvt.h"
/*
* For the sake of the code simplification we created the sensors info table
* with the sensor names, activation modes, threshold registers base address
* and the thresholds bit fields.
*/
static const struct pvt_sensor_info pvt_info[] = {
PVT_SENSOR_INFO(0, "CPU Core Temperature", hwmon_temp, TEMP, TTHRES),
PVT_SENSOR_INFO(0, "CPU Core Voltage", hwmon_in, VOLT, VTHRES),
PVT_SENSOR_INFO(1, "CPU Core Low-Vt", hwmon_in, LVT, LTHRES),
PVT_SENSOR_INFO(2, "CPU Core High-Vt", hwmon_in, HVT, HTHRES),
PVT_SENSOR_INFO(3, "CPU Core Standard-Vt", hwmon_in, SVT, STHRES),
};
/*
* The original translation formulae of the temperature (in degrees of Celsius)
* to PVT data and vice-versa are following:
* N = 1.8322e-8*(T^4) + 2.343e-5*(T^3) + 8.7018e-3*(T^2) + 3.9269*(T^1) +
* 1.7204e2,
* T = -1.6743e-11*(N^4) + 8.1542e-8*(N^3) + -1.8201e-4*(N^2) +
* 3.1020e-1*(N^1) - 4.838e1,
* where T = [-48.380, 147.438]C and N = [0, 1023].
* They must be accordingly altered to be suitable for the integer arithmetics.
* The technique is called 'factor redistribution', which just makes sure the
* multiplications and divisions are made so to have a result of the operations
* within the integer numbers limit. In addition we need to translate the
* formulae to accept millidegrees of Celsius. Here what they look like after
* the alterations:
* N = (18322e-20*(T^4) + 2343e-13*(T^3) + 87018e-9*(T^2) + 39269e-3*T +
* 17204e2) / 1e4,
* T = -16743e-12*(D^4) + 81542e-9*(D^3) - 182010e-6*(D^2) + 310200e-3*D -
* 48380,
* where T = [-48380, 147438] mC and N = [0, 1023].
*/
static const struct polynomial __maybe_unused poly_temp_to_N = {
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
.total_divider = 10000,
.terms = {
{4, 18322, 10000, 10000},
{3, 2343, 10000, 10},
{2, 87018, 10000, 10},
{1, 39269, 1000, 1},
{0, 1720400, 1, 1}
}
};
static const struct polynomial poly_N_to_temp = {
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
.total_divider = 1,
.terms = {
{4, -16743, 1000, 1},
{3, 81542, 1000, 1},
{2, -182010, 1000, 1},
{1, 310200, 1000, 1},
{0, -48380, 1, 1}
}
};
/*
* Similar alterations are performed for the voltage conversion equations.
* The original formulae are:
* N = 1.8658e3*V - 1.1572e3,
* V = (N + 1.1572e3) / 1.8658e3,
* where V = [0.620, 1.168] V and N = [0, 1023].
* After the optimization they looks as follows:
* N = (18658e-3*V - 11572) / 10,
* V = N * 10^5 / 18658 + 11572 * 10^4 / 18658.
*/
static const struct polynomial __maybe_unused poly_volt_to_N = {
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
.total_divider = 10,
.terms = {
{1, 18658, 1000, 1},
{0, -11572, 1, 1}
}
};
static const struct polynomial poly_N_to_volt = {
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
.total_divider = 10,
.terms = {
{1, 100000, 18658, 1},
{0, 115720000, 1, 18658}
}
};
static inline u32 pvt_update(void __iomem *reg, u32 mask, u32 data)
{
u32 old;
old = readl_relaxed(reg);
writel((old & ~mask) | (data & mask), reg);
return old & mask;
}
/*
* Baikal-T1 PVT mode can be updated only when the controller is disabled.
* So first we disable it, then set the new mode together with the controller
* getting back enabled. The same concerns the temperature trim and
* measurements timeout. If it is necessary the interface mutex is supposed
* to be locked at the time the operations are performed.
*/
static inline void pvt_set_mode(struct pvt_hwmon *pvt, u32 mode)
{
u32 old;
mode = FIELD_PREP(PVT_CTRL_MODE_MASK, mode);
old = pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_MODE_MASK | PVT_CTRL_EN,
mode | old);
}
static inline u32 pvt_calc_trim(long temp)
{
temp = clamp_val(temp, 0, PVT_TRIM_TEMP);
return DIV_ROUND_UP(temp, PVT_TRIM_STEP);
}
static inline void pvt_set_trim(struct pvt_hwmon *pvt, u32 trim)
{
u32 old;
trim = FIELD_PREP(PVT_CTRL_TRIM_MASK, trim);
old = pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_TRIM_MASK | PVT_CTRL_EN,
trim | old);
}
static inline void pvt_set_tout(struct pvt_hwmon *pvt, u32 tout)
{
u32 old;
old = pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
writel(tout, pvt->regs + PVT_TTIMEOUT);
pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, old);
}
/*
* This driver can optionally provide the hwmon alarms for each sensor the PVT
* controller supports. The alarms functionality is made compile-time
* configurable due to the hardware interface implementation peculiarity
* described further in this comment. So in case if alarms are unnecessary in
* your system design it's recommended to have them disabled to prevent the PVT
* IRQs being periodically raised to get the data cache/alarms status up to
* date.
*
* Baikal-T1 PVT embedded controller is based on the Analog Bits PVT sensor,
* but is equipped with a dedicated control wrapper. It exposes the PVT
* sub-block registers space via the APB3 bus. In addition the wrapper provides
* a common interrupt vector of the sensors conversion completion events and
* threshold value alarms. Alas the wrapper interface hasn't been fully thought
* through. There is only one sensor can be activated at a time, for which the
* thresholds comparator is enabled right after the data conversion is
* completed. Due to this if alarms need to be implemented for all available
* sensors we can't just set the thresholds and enable the interrupts. We need
* to enable the sensors one after another and let the controller to detect
* the alarms by itself at each conversion. This also makes pointless to handle
* the alarms interrupts, since in occasion they happen synchronously with
* data conversion completion. The best driver design would be to have the
* completion interrupts enabled only and keep the converted value in the
* driver data cache. This solution is implemented if hwmon alarms are enabled
* in this driver. In case if the alarms are disabled, the conversion is
* performed on demand at the time a sensors input file is read.
*/
#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
#define pvt_hard_isr NULL
static irqreturn_t pvt_soft_isr(int irq, void *data)
{
const struct pvt_sensor_info *info;
struct pvt_hwmon *pvt = data;
struct pvt_cache *cache;
u32 val, thres_sts, old;
/*
* DVALID bit will be cleared by reading the data. We need to save the
* status before the next conversion happens. Threshold events will be
* handled a bit later.
*/
thres_sts = readl(pvt->regs + PVT_RAW_INTR_STAT);
/*
* Then lets recharge the PVT interface with the next sampling mode.
* Lock the interface mutex to serialize trim, timeouts and alarm
* thresholds settings.
*/
cache = &pvt->cache[pvt->sensor];
info = &pvt_info[pvt->sensor];
pvt->sensor = (pvt->sensor == PVT_SENSOR_LAST) ?
PVT_SENSOR_FIRST : (pvt->sensor + 1);
/*
* For some reason we have to mask the interrupt before changing the
* mode, otherwise sometimes the temperature mode doesn't get
* activated even though the actual mode in the ctrl register
* corresponds to one. Then we read the data. By doing so we also
* recharge the data conversion. After this the mode corresponding
* to the next sensor in the row is set. Finally we enable the
* interrupts back.
*/
mutex_lock(&pvt->iface_mtx);
old = pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID,
PVT_INTR_DVALID);
val = readl(pvt->regs + PVT_DATA);
pvt_set_mode(pvt, pvt_info[pvt->sensor].mode);
pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID, old);
mutex_unlock(&pvt->iface_mtx);
/*
* We can now update the data cache with data just retrieved from the
* sensor. Lock write-seqlock to make sure the reader has a coherent
* data.
*/
write_seqlock(&cache->data_seqlock);
cache->data = FIELD_GET(PVT_DATA_DATA_MASK, val);
write_sequnlock(&cache->data_seqlock);
/*
* While PVT core is doing the next mode data conversion, we'll check
* whether the alarms were triggered for the current sensor. Note that
* according to the documentation only one threshold IRQ status can be
* set at a time, that's why if-else statement is utilized.
*/
if ((thres_sts & info->thres_sts_lo) ^ cache->thres_sts_lo) {
WRITE_ONCE(cache->thres_sts_lo, thres_sts & info->thres_sts_lo);
hwmon_notify_event(pvt->hwmon, info->type, info->attr_min_alarm,
info->channel);
} else if ((thres_sts & info->thres_sts_hi) ^ cache->thres_sts_hi) {
WRITE_ONCE(cache->thres_sts_hi, thres_sts & info->thres_sts_hi);
hwmon_notify_event(pvt->hwmon, info->type, info->attr_max_alarm,
info->channel);
}
return IRQ_HANDLED;
}
static inline umode_t pvt_limit_is_visible(enum pvt_sensor_type type)
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
{
return 0644;
}
static inline umode_t pvt_alarm_is_visible(enum pvt_sensor_type type)
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
{
return 0444;
}
static int pvt_read_data(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
long *val)
{
struct pvt_cache *cache = &pvt->cache[type];
unsigned int seq;
u32 data;
do {
seq = read_seqbegin(&cache->data_seqlock);
data = cache->data;
} while (read_seqretry(&cache->data_seqlock, seq));
if (type == PVT_TEMP)
*val = polynomial_calc(&poly_N_to_temp, data);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
else
*val = polynomial_calc(&poly_N_to_volt, data);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
return 0;
}
static int pvt_read_limit(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
bool is_low, long *val)
{
u32 data;
/* No need in serialization, since it is just read from MMIO. */
data = readl(pvt->regs + pvt_info[type].thres_base);
if (is_low)
data = FIELD_GET(PVT_THRES_LO_MASK, data);
else
data = FIELD_GET(PVT_THRES_HI_MASK, data);
if (type == PVT_TEMP)
*val = polynomial_calc(&poly_N_to_temp, data);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
else
*val = polynomial_calc(&poly_N_to_volt, data);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
return 0;
}
static int pvt_write_limit(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
bool is_low, long val)
{
u32 data, limit, mask;
int ret;
if (type == PVT_TEMP) {
val = clamp(val, PVT_TEMP_MIN, PVT_TEMP_MAX);
data = polynomial_calc(&poly_temp_to_N, val);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
} else {
val = clamp(val, PVT_VOLT_MIN, PVT_VOLT_MAX);
data = polynomial_calc(&poly_volt_to_N, val);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
}
/* Serialize limit update, since a part of the register is changed. */
ret = mutex_lock_interruptible(&pvt->iface_mtx);
if (ret)
return ret;
/* Make sure the upper and lower ranges don't intersect. */
limit = readl(pvt->regs + pvt_info[type].thres_base);
if (is_low) {
limit = FIELD_GET(PVT_THRES_HI_MASK, limit);
data = clamp_val(data, PVT_DATA_MIN, limit);
data = FIELD_PREP(PVT_THRES_LO_MASK, data);
mask = PVT_THRES_LO_MASK;
} else {
limit = FIELD_GET(PVT_THRES_LO_MASK, limit);
data = clamp_val(data, limit, PVT_DATA_MAX);
data = FIELD_PREP(PVT_THRES_HI_MASK, data);
mask = PVT_THRES_HI_MASK;
}
pvt_update(pvt->regs + pvt_info[type].thres_base, mask, data);
mutex_unlock(&pvt->iface_mtx);
return 0;
}
static int pvt_read_alarm(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
bool is_low, long *val)
{
if (is_low)
*val = !!READ_ONCE(pvt->cache[type].thres_sts_lo);
else
*val = !!READ_ONCE(pvt->cache[type].thres_sts_hi);
return 0;
}
static const struct hwmon_channel_info *pvt_channel_info[] = {
HWMON_CHANNEL_INFO(chip,
HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL),
HWMON_CHANNEL_INFO(temp,
HWMON_T_INPUT | HWMON_T_TYPE | HWMON_T_LABEL |
HWMON_T_MIN | HWMON_T_MIN_ALARM |
HWMON_T_MAX | HWMON_T_MAX_ALARM |
HWMON_T_OFFSET),
HWMON_CHANNEL_INFO(in,
HWMON_I_INPUT | HWMON_I_LABEL |
HWMON_I_MIN | HWMON_I_MIN_ALARM |
HWMON_I_MAX | HWMON_I_MAX_ALARM,
HWMON_I_INPUT | HWMON_I_LABEL |
HWMON_I_MIN | HWMON_I_MIN_ALARM |
HWMON_I_MAX | HWMON_I_MAX_ALARM,
HWMON_I_INPUT | HWMON_I_LABEL |
HWMON_I_MIN | HWMON_I_MIN_ALARM |
HWMON_I_MAX | HWMON_I_MAX_ALARM,
HWMON_I_INPUT | HWMON_I_LABEL |
HWMON_I_MIN | HWMON_I_MIN_ALARM |
HWMON_I_MAX | HWMON_I_MAX_ALARM),
NULL
};
#else /* !CONFIG_SENSORS_BT1_PVT_ALARMS */
static irqreturn_t pvt_hard_isr(int irq, void *data)
{
struct pvt_hwmon *pvt = data;
struct pvt_cache *cache;
u32 val;
/*
* Mask the DVALID interrupt so after exiting from the handler a
* repeated conversion wouldn't happen.
*/
pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID,
PVT_INTR_DVALID);
/*
* Nothing special for alarm-less driver. Just read the data, update
* the cache and notify a waiter of this event.
*/
val = readl(pvt->regs + PVT_DATA);
if (!(val & PVT_DATA_VALID)) {
dev_err(pvt->dev, "Got IRQ when data isn't valid\n");
return IRQ_HANDLED;
}
cache = &pvt->cache[pvt->sensor];
WRITE_ONCE(cache->data, FIELD_GET(PVT_DATA_DATA_MASK, val));
complete(&cache->conversion);
return IRQ_HANDLED;
}
#define pvt_soft_isr NULL
static inline umode_t pvt_limit_is_visible(enum pvt_sensor_type type)
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
{
return 0;
}
static inline umode_t pvt_alarm_is_visible(enum pvt_sensor_type type)
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
{
return 0;
}
static int pvt_read_data(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
long *val)
{
struct pvt_cache *cache = &pvt->cache[type];
unsigned long timeout;
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
u32 data;
int ret;
/*
* Lock PVT conversion interface until data cache is updated. The
* data read procedure is following: set the requested PVT sensor
* mode, enable IRQ and conversion, wait until conversion is finished,
* then disable conversion and IRQ, and read the cached data.
*/
ret = mutex_lock_interruptible(&pvt->iface_mtx);
if (ret)
return ret;
pvt->sensor = type;
pvt_set_mode(pvt, pvt_info[type].mode);
/*
* Unmask the DVALID interrupt and enable the sensors conversions.
* Do the reverse procedure when conversion is done.
*/
pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID, 0);
pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, PVT_CTRL_EN);
/*
* Wait with timeout since in case if the sensor is suddenly powered
* down the request won't be completed and the caller will hang up on
* this procedure until the power is back up again. Multiply the
* timeout by the factor of two to prevent a false timeout.
*/
timeout = 2 * usecs_to_jiffies(ktime_to_us(pvt->timeout));
ret = wait_for_completion_timeout(&cache->conversion, timeout);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID,
PVT_INTR_DVALID);
data = READ_ONCE(cache->data);
mutex_unlock(&pvt->iface_mtx);
if (!ret)
return -ETIMEDOUT;
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
if (type == PVT_TEMP)
*val = polynomial_calc(&poly_N_to_temp, data);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
else
*val = polynomial_calc(&poly_N_to_volt, data);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
return 0;
}
static int pvt_read_limit(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
bool is_low, long *val)
{
return -EOPNOTSUPP;
}
static int pvt_write_limit(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
bool is_low, long val)
{
return -EOPNOTSUPP;
}
static int pvt_read_alarm(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
bool is_low, long *val)
{
return -EOPNOTSUPP;
}
static const struct hwmon_channel_info *pvt_channel_info[] = {
HWMON_CHANNEL_INFO(chip,
HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL),
HWMON_CHANNEL_INFO(temp,
HWMON_T_INPUT | HWMON_T_TYPE | HWMON_T_LABEL |
HWMON_T_OFFSET),
HWMON_CHANNEL_INFO(in,
HWMON_I_INPUT | HWMON_I_LABEL,
HWMON_I_INPUT | HWMON_I_LABEL,
HWMON_I_INPUT | HWMON_I_LABEL,
HWMON_I_INPUT | HWMON_I_LABEL),
NULL
};
#endif /* !CONFIG_SENSORS_BT1_PVT_ALARMS */
static inline bool pvt_hwmon_channel_is_valid(enum hwmon_sensor_types type,
int ch)
{
switch (type) {
case hwmon_temp:
if (ch < 0 || ch >= PVT_TEMP_CHS)
return false;
break;
case hwmon_in:
if (ch < 0 || ch >= PVT_VOLT_CHS)
return false;
break;
default:
break;
}
/* The rest of the types are independent from the channel number. */
return true;
}
static umode_t pvt_hwmon_is_visible(const void *data,
enum hwmon_sensor_types type,
u32 attr, int ch)
{
if (!pvt_hwmon_channel_is_valid(type, ch))
return 0;
switch (type) {
case hwmon_chip:
switch (attr) {
case hwmon_chip_update_interval:
return 0644;
}
break;
case hwmon_temp:
switch (attr) {
case hwmon_temp_input:
case hwmon_temp_type:
case hwmon_temp_label:
return 0444;
case hwmon_temp_min:
case hwmon_temp_max:
return pvt_limit_is_visible(ch);
case hwmon_temp_min_alarm:
case hwmon_temp_max_alarm:
return pvt_alarm_is_visible(ch);
case hwmon_temp_offset:
return 0644;
}
break;
case hwmon_in:
switch (attr) {
case hwmon_in_input:
case hwmon_in_label:
return 0444;
case hwmon_in_min:
case hwmon_in_max:
return pvt_limit_is_visible(PVT_VOLT + ch);
case hwmon_in_min_alarm:
case hwmon_in_max_alarm:
return pvt_alarm_is_visible(PVT_VOLT + ch);
}
break;
default:
break;
}
return 0;
}
static int pvt_read_trim(struct pvt_hwmon *pvt, long *val)
{
u32 data;
data = readl(pvt->regs + PVT_CTRL);
*val = FIELD_GET(PVT_CTRL_TRIM_MASK, data) * PVT_TRIM_STEP;
return 0;
}
static int pvt_write_trim(struct pvt_hwmon *pvt, long val)
{
u32 trim;
int ret;
/*
* Serialize trim update, since a part of the register is changed and
* the controller is supposed to be disabled during this operation.
*/
ret = mutex_lock_interruptible(&pvt->iface_mtx);
if (ret)
return ret;
trim = pvt_calc_trim(val);
pvt_set_trim(pvt, trim);
mutex_unlock(&pvt->iface_mtx);
return 0;
}
static int pvt_read_timeout(struct pvt_hwmon *pvt, long *val)
{
int ret;
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
ret = mutex_lock_interruptible(&pvt->iface_mtx);
if (ret)
return ret;
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
/* Return the result in msec as hwmon sysfs interface requires. */
*val = ktime_to_ms(pvt->timeout);
mutex_unlock(&pvt->iface_mtx);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
return 0;
}
static int pvt_write_timeout(struct pvt_hwmon *pvt, long val)
{
unsigned long rate;
ktime_t kt, cache;
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
u32 data;
int ret;
rate = clk_get_rate(pvt->clks[PVT_CLOCK_REF].clk);
if (!rate)
return -ENODEV;
/*
* If alarms are enabled, the requested timeout must be divided
* between all available sensors to have the requested delay
* applicable to each individual sensor.
*/
cache = kt = ms_to_ktime(val);
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
kt = ktime_divns(kt, PVT_SENSORS_NUM);
#endif
/*
* Subtract a constant lag, which always persists due to the limited
* PVT sampling rate. Make sure the timeout is not negative.
*/
kt = ktime_sub_ns(kt, PVT_TOUT_MIN);
if (ktime_to_ns(kt) < 0)
kt = ktime_set(0, 0);
/*
* Finally recalculate the timeout in terms of the reference clock
* period.
*/
data = ktime_divns(kt * rate, NSEC_PER_SEC);
/*
* Update the measurements delay, but lock the interface first, since
* we have to disable PVT in order to have the new delay actually
* updated.
*/
ret = mutex_lock_interruptible(&pvt->iface_mtx);
if (ret)
return ret;
pvt_set_tout(pvt, data);
pvt->timeout = cache;
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
mutex_unlock(&pvt->iface_mtx);
return 0;
}
static int pvt_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
u32 attr, int ch, long *val)
{
struct pvt_hwmon *pvt = dev_get_drvdata(dev);
if (!pvt_hwmon_channel_is_valid(type, ch))
return -EINVAL;
switch (type) {
case hwmon_chip:
switch (attr) {
case hwmon_chip_update_interval:
return pvt_read_timeout(pvt, val);
}
break;
case hwmon_temp:
switch (attr) {
case hwmon_temp_input:
return pvt_read_data(pvt, ch, val);
case hwmon_temp_type:
*val = 1;
return 0;
case hwmon_temp_min:
return pvt_read_limit(pvt, ch, true, val);
case hwmon_temp_max:
return pvt_read_limit(pvt, ch, false, val);
case hwmon_temp_min_alarm:
return pvt_read_alarm(pvt, ch, true, val);
case hwmon_temp_max_alarm:
return pvt_read_alarm(pvt, ch, false, val);
case hwmon_temp_offset:
return pvt_read_trim(pvt, val);
}
break;
case hwmon_in:
switch (attr) {
case hwmon_in_input:
return pvt_read_data(pvt, PVT_VOLT + ch, val);
case hwmon_in_min:
return pvt_read_limit(pvt, PVT_VOLT + ch, true, val);
case hwmon_in_max:
return pvt_read_limit(pvt, PVT_VOLT + ch, false, val);
case hwmon_in_min_alarm:
return pvt_read_alarm(pvt, PVT_VOLT + ch, true, val);
case hwmon_in_max_alarm:
return pvt_read_alarm(pvt, PVT_VOLT + ch, false, val);
}
break;
default:
break;
}
return -EOPNOTSUPP;
}
static int pvt_hwmon_read_string(struct device *dev,
enum hwmon_sensor_types type,
u32 attr, int ch, const char **str)
{
if (!pvt_hwmon_channel_is_valid(type, ch))
return -EINVAL;
switch (type) {
case hwmon_temp:
switch (attr) {
case hwmon_temp_label:
*str = pvt_info[ch].label;
return 0;
}
break;
case hwmon_in:
switch (attr) {
case hwmon_in_label:
*str = pvt_info[PVT_VOLT + ch].label;
return 0;
}
break;
default:
break;
}
return -EOPNOTSUPP;
}
static int pvt_hwmon_write(struct device *dev, enum hwmon_sensor_types type,
u32 attr, int ch, long val)
{
struct pvt_hwmon *pvt = dev_get_drvdata(dev);
if (!pvt_hwmon_channel_is_valid(type, ch))
return -EINVAL;
switch (type) {
case hwmon_chip:
switch (attr) {
case hwmon_chip_update_interval:
return pvt_write_timeout(pvt, val);
}
break;
case hwmon_temp:
switch (attr) {
case hwmon_temp_min:
return pvt_write_limit(pvt, ch, true, val);
case hwmon_temp_max:
return pvt_write_limit(pvt, ch, false, val);
case hwmon_temp_offset:
return pvt_write_trim(pvt, val);
}
break;
case hwmon_in:
switch (attr) {
case hwmon_in_min:
return pvt_write_limit(pvt, PVT_VOLT + ch, true, val);
case hwmon_in_max:
return pvt_write_limit(pvt, PVT_VOLT + ch, false, val);
}
break;
default:
break;
}
return -EOPNOTSUPP;
}
static const struct hwmon_ops pvt_hwmon_ops = {
.is_visible = pvt_hwmon_is_visible,
.read = pvt_hwmon_read,
.read_string = pvt_hwmon_read_string,
.write = pvt_hwmon_write
};
static const struct hwmon_chip_info pvt_hwmon_info = {
.ops = &pvt_hwmon_ops,
.info = pvt_channel_info
};
static void pvt_clear_data(void *data)
{
struct pvt_hwmon *pvt = data;
#if !defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
int idx;
for (idx = 0; idx < PVT_SENSORS_NUM; ++idx)
complete_all(&pvt->cache[idx].conversion);
#endif
mutex_destroy(&pvt->iface_mtx);
}
static struct pvt_hwmon *pvt_create_data(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct pvt_hwmon *pvt;
int ret, idx;
pvt = devm_kzalloc(dev, sizeof(*pvt), GFP_KERNEL);
if (!pvt)
return ERR_PTR(-ENOMEM);
ret = devm_add_action(dev, pvt_clear_data, pvt);
if (ret) {
dev_err(dev, "Can't add PVT data clear action\n");
return ERR_PTR(ret);
}
pvt->dev = dev;
pvt->sensor = PVT_SENSOR_FIRST;
mutex_init(&pvt->iface_mtx);
#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
for (idx = 0; idx < PVT_SENSORS_NUM; ++idx)
seqlock_init(&pvt->cache[idx].data_seqlock);
#else
for (idx = 0; idx < PVT_SENSORS_NUM; ++idx)
init_completion(&pvt->cache[idx].conversion);
#endif
return pvt;
}
static int pvt_request_regs(struct pvt_hwmon *pvt)
{
struct platform_device *pdev = to_platform_device(pvt->dev);
struct resource *res;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(pvt->dev, "Couldn't find PVT memresource\n");
return -EINVAL;
}
pvt->regs = devm_ioremap_resource(pvt->dev, res);
if (IS_ERR(pvt->regs))
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
return PTR_ERR(pvt->regs);
return 0;
}
static void pvt_disable_clks(void *data)
{
struct pvt_hwmon *pvt = data;
clk_bulk_disable_unprepare(PVT_CLOCK_NUM, pvt->clks);
}
static int pvt_request_clks(struct pvt_hwmon *pvt)
{
int ret;
pvt->clks[PVT_CLOCK_APB].id = "pclk";
pvt->clks[PVT_CLOCK_REF].id = "ref";
ret = devm_clk_bulk_get(pvt->dev, PVT_CLOCK_NUM, pvt->clks);
if (ret) {
dev_err(pvt->dev, "Couldn't get PVT clocks descriptors\n");
return ret;
}
ret = clk_bulk_prepare_enable(PVT_CLOCK_NUM, pvt->clks);
if (ret) {
dev_err(pvt->dev, "Couldn't enable the PVT clocks\n");
return ret;
}
ret = devm_add_action_or_reset(pvt->dev, pvt_disable_clks, pvt);
if (ret) {
dev_err(pvt->dev, "Can't add PVT clocks disable action\n");
return ret;
}
return 0;
}
static int pvt_check_pwr(struct pvt_hwmon *pvt)
{
unsigned long tout;
int ret = 0;
u32 data;
/*
* Test out the sensor conversion functionality. If it is not done on
* time then the domain must have been unpowered and we won't be able
* to use the device later in this driver.
* Note If the power source is lost during the normal driver work the
* data read procedure will either return -ETIMEDOUT (for the
* alarm-less driver configuration) or just stop the repeated
* conversion. In the later case alas we won't be able to detect the
* problem.
*/
pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_ALL, PVT_INTR_ALL);
pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, PVT_CTRL_EN);
pvt_set_tout(pvt, 0);
readl(pvt->regs + PVT_DATA);
tout = PVT_TOUT_MIN / NSEC_PER_USEC;
usleep_range(tout, 2 * tout);
data = readl(pvt->regs + PVT_DATA);
if (!(data & PVT_DATA_VALID)) {
ret = -ENODEV;
dev_err(pvt->dev, "Sensor is powered down\n");
}
pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
return ret;
}
static int pvt_init_iface(struct pvt_hwmon *pvt)
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
{
unsigned long rate;
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
u32 trim, temp;
rate = clk_get_rate(pvt->clks[PVT_CLOCK_REF].clk);
if (!rate) {
dev_err(pvt->dev, "Invalid reference clock rate\n");
return -ENODEV;
}
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
/*
* Make sure all interrupts and controller are disabled so not to
* accidentally have ISR executed before the driver data is fully
* initialized. Clear the IRQ status as well.
*/
pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_ALL, PVT_INTR_ALL);
pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
readl(pvt->regs + PVT_CLR_INTR);
readl(pvt->regs + PVT_DATA);
/* Setup default sensor mode, timeout and temperature trim. */
pvt_set_mode(pvt, pvt_info[pvt->sensor].mode);
pvt_set_tout(pvt, PVT_TOUT_DEF);
/*
* Preserve the current ref-clock based delay (Ttotal) between the
* sensors data samples in the driver data so not to recalculate it
* each time on the data requests and timeout reads. It consists of the
* delay introduced by the internal ref-clock timer (N / Fclk) and the
* constant timeout caused by each conversion latency (Tmin):
* Ttotal = N / Fclk + Tmin
* If alarms are enabled the sensors are polled one after another and
* in order to get the next measurement of a particular sensor the
* caller will have to wait for at most until all the others are
* polled. In that case the formulae will look a bit different:
* Ttotal = 5 * (N / Fclk + Tmin)
*/
#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
pvt->timeout = ktime_set(PVT_SENSORS_NUM * PVT_TOUT_DEF, 0);
pvt->timeout = ktime_divns(pvt->timeout, rate);
pvt->timeout = ktime_add_ns(pvt->timeout, PVT_SENSORS_NUM * PVT_TOUT_MIN);
#else
pvt->timeout = ktime_set(PVT_TOUT_DEF, 0);
pvt->timeout = ktime_divns(pvt->timeout, rate);
pvt->timeout = ktime_add_ns(pvt->timeout, PVT_TOUT_MIN);
#endif
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
trim = PVT_TRIM_DEF;
if (!of_property_read_u32(pvt->dev->of_node,
"baikal,pvt-temp-offset-millicelsius", &temp))
trim = pvt_calc_trim(temp);
pvt_set_trim(pvt, trim);
return 0;
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
}
static int pvt_request_irq(struct pvt_hwmon *pvt)
{
struct platform_device *pdev = to_platform_device(pvt->dev);
int ret;
pvt->irq = platform_get_irq(pdev, 0);
if (pvt->irq < 0)
return pvt->irq;
ret = devm_request_threaded_irq(pvt->dev, pvt->irq,
pvt_hard_isr, pvt_soft_isr,
#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
IRQF_SHARED | IRQF_TRIGGER_HIGH |
IRQF_ONESHOT,
#else
IRQF_SHARED | IRQF_TRIGGER_HIGH,
#endif
"pvt", pvt);
if (ret) {
dev_err(pvt->dev, "Couldn't request PVT IRQ\n");
return ret;
}
return 0;
}
static int pvt_create_hwmon(struct pvt_hwmon *pvt)
{
pvt->hwmon = devm_hwmon_device_register_with_info(pvt->dev, "pvt", pvt,
&pvt_hwmon_info, NULL);
if (IS_ERR(pvt->hwmon)) {
dev_err(pvt->dev, "Couldn't create hwmon device\n");
return PTR_ERR(pvt->hwmon);
}
return 0;
}
#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
static void pvt_disable_iface(void *data)
{
struct pvt_hwmon *pvt = data;
mutex_lock(&pvt->iface_mtx);
pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID,
PVT_INTR_DVALID);
mutex_unlock(&pvt->iface_mtx);
}
static int pvt_enable_iface(struct pvt_hwmon *pvt)
{
int ret;
ret = devm_add_action(pvt->dev, pvt_disable_iface, pvt);
if (ret) {
dev_err(pvt->dev, "Can't add PVT disable interface action\n");
return ret;
}
/*
* Enable sensors data conversion and IRQ. We need to lock the
* interface mutex since hwmon has just been created and the
* corresponding sysfs files are accessible from user-space,
* which theoretically may cause races.
*/
mutex_lock(&pvt->iface_mtx);
pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID, 0);
pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, PVT_CTRL_EN);
mutex_unlock(&pvt->iface_mtx);
return 0;
}
#else /* !CONFIG_SENSORS_BT1_PVT_ALARMS */
static int pvt_enable_iface(struct pvt_hwmon *pvt)
{
return 0;
}
#endif /* !CONFIG_SENSORS_BT1_PVT_ALARMS */
static int pvt_probe(struct platform_device *pdev)
{
struct pvt_hwmon *pvt;
int ret;
pvt = pvt_create_data(pdev);
if (IS_ERR(pvt))
return PTR_ERR(pvt);
ret = pvt_request_regs(pvt);
if (ret)
return ret;
ret = pvt_request_clks(pvt);
if (ret)
return ret;
ret = pvt_check_pwr(pvt);
if (ret)
return ret;
ret = pvt_init_iface(pvt);
if (ret)
return ret;
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 14:28:05 +00:00
ret = pvt_request_irq(pvt);
if (ret)
return ret;
ret = pvt_create_hwmon(pvt);
if (ret)
return ret;
ret = pvt_enable_iface(pvt);
if (ret)
return ret;
return 0;
}
static const struct of_device_id pvt_of_match[] = {
{ .compatible = "baikal,bt1-pvt" },
{ }
};
MODULE_DEVICE_TABLE(of, pvt_of_match);
static struct platform_driver pvt_driver = {
.probe = pvt_probe,
.driver = {
.name = "bt1-pvt",
.of_match_table = pvt_of_match
}
};
module_platform_driver(pvt_driver);
MODULE_AUTHOR("Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>");
MODULE_DESCRIPTION("Baikal-T1 PVT driver");
MODULE_LICENSE("GPL v2");