linux/io_uring/Makefile

15 lines
477 B
Makefile
Raw Normal View History

# SPDX-License-Identifier: GPL-2.0
#
# Makefile for io_uring
obj-$(CONFIG_IO_URING) += io_uring.o xattr.o nop.o fs.o splice.o \
sync.o advise.o filetable.o \
openclose.o uring_cmd.o epoll.o \
statx.o net.o msg_ring.o timeout.o \
sqpoll.o fdinfo.o tctx.o poll.o \
cancel.o kbuf.o rsrc.o rw.o opdef.o \
notif.o waitid.o register.o truncate.o
obj-$(CONFIG_IO_WQ) += io-wq.o
io_uring: add support for futex wake and wait Add support for FUTEX_WAKE/WAIT primitives. IORING_OP_FUTEX_WAKE is mix of FUTEX_WAKE and FUTEX_WAKE_BITSET, as it does support passing in a bitset. Similary, IORING_OP_FUTEX_WAIT is a mix of FUTEX_WAIT and FUTEX_WAIT_BITSET. For both of them, they are using the futex2 interface. FUTEX_WAKE is straight forward, as those can always be done directly from the io_uring submission without needing async handling. For FUTEX_WAIT, things are a bit more complicated. If the futex isn't ready, then we rely on a callback via futex_queue->wake() when someone wakes up the futex. From that calback, we queue up task_work with the original task, which will post a CQE and wake it, if necessary. Cancelations are supported, both from the application point-of-view, but also to be able to cancel pending waits if the ring exits before all events have occurred. The return value of futex_unqueue() is used to gate who wins the potential race between cancelation and futex wakeups. Whomever gets a 'ret == 1' return from that claims ownership of the io_uring futex request. This is just the barebones wait/wake support. PI or REQUEUE support is not added at this point, unclear if we might look into that later. Likewise, explicit timeouts are not supported either. It is expected that users that need timeouts would do so via the usual io_uring mechanism to do that using linked timeouts. The SQE format is as follows: `addr` Address of futex `fd` futex2(2) FUTEX2_* flags `futex_flags` io_uring specific command flags. None valid now. `addr2` Value of futex `addr3` Mask to wake/wait Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2023-06-08 17:57:40 +00:00
obj-$(CONFIG_FUTEX) += futex.o
io-uring: add napi busy poll support This adds the napi busy polling support in io_uring.c. It adds a new napi_list to the io_ring_ctx structure. This list contains the list of napi_id's that are currently enabled for busy polling. The list is synchronized by the new napi_lock spin lock. The current default napi busy polling time is stored in napi_busy_poll_to. If napi busy polling is not enabled, the value is 0. In addition there is also a hash table. The hash table store the napi id and the pointer to the above list nodes. The hash table is used to speed up the lookup to the list elements. The hash table is synchronized with rcu. The NAPI_TIMEOUT is stored as a timeout to make sure that the time a napi entry is stored in the napi list is limited. The busy poll timeout is also stored as part of the io_wait_queue. This is necessary as for sq polling the poll interval needs to be adjusted and the napi callback allows only to pass in one value. This has been tested with two simple programs from the liburing library repository: the napi client and the napi server program. The client sends a request, which has a timestamp in its payload and the server replies with the same payload. The client calculates the roundtrip time and stores it to calculate the results. The client is running on host1 and the server is running on host 2 (in the same rack). The measured times below are roundtrip times. They are average times over 5 runs each. Each run measures 1 million roundtrips. no rx coal rx coal: frames=88,usecs=33 Default 57us 56us client_poll=100us 47us 46us server_poll=100us 51us 46us client_poll=100us+ 40us 40us server_poll=100us client_poll=100us+ 41us 39us server_poll=100us+ prefer napi busy poll on client client_poll=100us+ 41us 39us server_poll=100us+ prefer napi busy poll on server client_poll=100us+ 41us 39us server_poll=100us+ prefer napi busy poll on client + server Signed-off-by: Stefan Roesch <shr@devkernel.io> Suggested-by: Olivier Langlois <olivier@trillion01.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/r/20230608163839.2891748-5-shr@devkernel.io Signed-off-by: Jens Axboe <axboe@kernel.dk>
2023-06-08 16:38:36 +00:00
obj-$(CONFIG_NET_RX_BUSY_POLL) += napi.o