linux/net/mac80211/Makefile

64 lines
1.2 KiB
Makefile
Raw Normal View History

obj-$(CONFIG_MAC80211) += mac80211.o
# mac80211 objects
mac80211-y := \
main.o status.o \
sta_info.o \
wep.o \
wpa.o \
scan.o offchannel.o \
ht.o agg-tx.o agg-rx.o \
vht.o \
ibss.o \
iface.o \
rate.o \
michael.o \
tkip.o \
aes_ccm.o \
aes_gcm.o \
aes_cmac.o \
aes_gmac.o \
cfg.o \
ethtool.o \
rx.o \
spectmgmt.o \
tx.o \
key.o \
util.o \
wme.o \
cfg80211/mac80211: better channel handling Currently (all tested with hwsim) you can do stupid things like setting up an AP on a certain channel, then adding another virtual interface and making that associate on another channel -- this will make the beaconing to move channel but obviously without the necessary IEs data update. In order to improve this situation, first make the configuration APIs (cfg80211 and nl80211) aware of multi-channel operation -- we'll eventually need that in the future anyway. There's one userland API change and one API addition. The API change is that now SET_WIPHY must be called with virtual interface index rather than only wiphy index in order to take effect for that interface -- luckily all current users (hostapd) do that. For monitor interfaces, the old setting is preserved, but monitors are always slaved to other devices anyway so no guarantees. The second userland API change is the introduction of a per virtual interface SET_CHANNEL command, that hostapd should use going forward to make it easier to understand what's going on (it can automatically detect a kernel with this command). Other than mac80211, no existing cfg80211 drivers are affected by this change because they only allow a single virtual interface. mac80211, however, now needs to be aware that the channel settings are per interface now, and needs to disallow (for now) real multi-channel operation, which is another important part of this patch. One of the immediate benefits is that you can now start hostapd to operate on a hardware that already has a connection on another virtual interface, as long as you specify the same channel. Note that two things are left unhandled (this is an improvement -- not a complete fix): * different HT/no-HT modes currently you could start an HT AP and then connect to a non-HT network on the same channel which would configure the hardware for no HT; that can be fixed fairly easily * CSA An AP we're connected to on a virtual interface might indicate switching channels, and in that case we would follow it, regardless of how many other interfaces are operating; this requires more effort to fix but is pretty rare after all Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-05-05 13:25:02 +00:00
event.o \
chan.o \
trace.o mlme.o \
tdls.o \
ocb.o
mac80211-$(CONFIG_MAC80211_LEDS) += led.o
mac80211-$(CONFIG_MAC80211_DEBUGFS) += \
debugfs.o \
debugfs_sta.o \
debugfs_netdev.o \
debugfs_key.o
mac80211-$(CONFIG_MAC80211_MESH) += \
mesh.o \
mesh_pathtbl.o \
mesh_plink.o \
mesh_hwmp.o \
mac80211: mesh power save basics Add routines to - maintain a PS mode for each peer and a non-peer PS mode - indicate own PS mode in transmitted frames - track neighbor STAs power modes - buffer frames when neighbors are in PS mode - add TIM and Awake Window IE to beacons - release frames in Mesh Peer Service Periods Add local_pm to sta_info to represent the link-specific power mode at this station towards the remote station. When a peer link is established, use the default power mode stored in mesh config. Update the PS status if the peering status of a neighbor changes. Maintain a mesh power mode for non-peer mesh STAs. Set the non-peer power mode to active mode during peering. Authenticated mesh peering is currently not working when either node is configured to be in power save mode. Indicate the current power mode in transmitted frames. Use QoS Nulls to indicate mesh power mode transitions. For performance reasons, calls to the function setting the frame flags are placed in HWMP routing routines, as there the STA pointer is already available. Add peer_pm to sta_info to represent the peer's link-specific power mode towards the local station. Add nonpeer_pm to represent the peer's power mode towards all non-peer stations. Track power modes based on received frames. Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS neighbor counter and group-addressed frame buffer). Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame buffering routines in the tx path. Update num_sta_ps to buffer and release group-addressed frames after DTIM beacons. Announce the awake window duration in beacons if in light or deep sleep mode towards any peer or non-peer. Create a TIM IE similarly to AP mode and add it to mesh beacons. Parse received Awake Window IEs and check TIM IEs for buffered frames. Release frames towards peers in mesh Peer Service Periods. Use the corresponding trigger frames and monitor the MPSP status. Append a QoS Null as trigger frame if neccessary to properly end the MPSP. Currently, in HT channels MPSPs behave imperfectly and show large delay spikes and frame losses. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-30 17:14:08 +00:00
mesh_sync.o \
mesh_ps.o
mac80211-$(CONFIG_PM) += pm.o
CFLAGS_trace.o := -I$(src)
rc80211_minstrel-y := rc80211_minstrel.o
rc80211_minstrel-$(CONFIG_MAC80211_DEBUGFS) += rc80211_minstrel_debugfs.o
rc80211_minstrel_ht-y := rc80211_minstrel_ht.o
rc80211_minstrel_ht-$(CONFIG_MAC80211_DEBUGFS) += rc80211_minstrel_ht_debugfs.o
mac80211-$(CONFIG_MAC80211_RC_MINSTREL) += $(rc80211_minstrel-y)
mac80211-$(CONFIG_MAC80211_RC_MINSTREL_HT) += $(rc80211_minstrel_ht-y)
ccflags-y += -D__CHECK_ENDIAN__ -DDEBUG