store a bitmask of whether we've set a value into ccb->ccb_h.status,
whether we're in the watchdog routine for this command now, whether
we've set a grace period for this command and whether this command is
actually done.
See comments of rev 1.45 of isp.c for more complete information.
output mailbox values we want to get back out of the chip once a mailbox
command is done. Add storage for the maximum number of output mailbox
registers to the softc.
Roll minor version number.
the handle (i.e., generation number), so we will now need a function that
will take a handle and return a flat index [ 0 .. maxhandles-1 ] for
auxillary routines that need an index to get at buddy store values
(like dma maps or xflist pointers).
device with Yarrow, and although I coded for that in dev/MAKEDEV, I forgot
to _tell_ folks.
This commit adds back the /dev/urandom device (as a duplicate) of /dev/random,
until such time as it can be properly announced.
This will help the openssl users quite a lot.
(Reported by Matthew Jacob)
- Fix a couple of __inline__ (changed to __inline).
- Check also against DT_DATA_IN phase on parity/crc error.
(Merged from Pamela Delaney's changes in the Linux driver)
- Fix support for phase mismatch handling from the C code for
the C1010 (only useful for testing issue).
- Add an asynchonous notification handler for `lost device'
(AC_LOST).
This merges in changes from NetBSD which ensure bktr0
(actually bktr%d) is printed at the start of any output lines.
Submitted by: Thomas Klausner <wiz@danbala.ifoer.tuwien.ac.at>
This is work-in-progress, and the entropy-gathering routines are not
yet present. As such, this should be viewed as a pretty reasonable
PRNG with _ABSOLUTELY_NO_ security!!
Entropy gathering will be the subject of ongoing work.
This is written as a module, and as such is unloadable, but there is
no refcounting done. I would like to use something like device_busy(9)
to achieve this (eventually).
Lots of useful ideas from: bde, phk, Jeroen van Gelderen
Reviewed by: dfr
severely stripped down compared with its predecessor, and is measurably
a _lot_ faster.
Many thanks to Jeroen van Gelderen for lots of good ideas.
There is still a problem with this; it is written as a mudule, and as
such is theoretically unloadable. However, there is no refcounting done
as I would prefer to do that a'la device_busy(9), rather than some
"home-rolled" scheme. The point is pretty moot, as /dev/null is
effectively compulsory.
Reviewed by: dfr
the PnP probe is merely a stub as we make assumptions about some of this
hardware before we have probed it.
Since these devices (with the exception of the speaker) are 'standard',
suppress output in the !bootverbose case to clean up the probe messages
somewhat.
Renamed varible dst in ray_rx to mp as it is a pointer to an mbuf.
Correctly grok addresses in data packets.
Promte a couple of RECERRs to real errors.
Rewrote intro at top of file to reflect my better understanding of how it
the memory mapping works.
Clear the DONE list and move some thoughts into the TODO list.
Remove RECERR from RAY_DEBUG
Start to use a desired network parameter structure, only used in download
code as I've realised that there are some problems with the idea.
Break up ray_rx, and move the data packet handler into a seperate function. This meant some knock on changes in ray_rx_mgt/ray_rx_ctl to do with
mbuf freeing.
Remove some debug code/XXX comments that are out of date.
Force alphas to prefer mem mapping as the default.
Basically, we have a pointer to a function which we can call which will
return us a pointer to firmware for the card we have. We call this function
(if it's non-NULL) with the address of our mdvec f/w pointer.
The way this works is that if ispfw (as a module or a static) is loaded,
it initializes the pointer in isp_pci, so we can call into to it to fetch
a pointer to a f/w set.
If ispfw is MOD_UNLOADed, it's retained a pointer to our mdvec f/w pointers,
which then get zeroed out so we don't have any references to data that's
now gone from kernel memory. Removing the f/w saves ~360KBytes.
Alas, there is no autounload mechanism that works for is here.
through, establish what our LUN width is. Unfortunately, we can't ask
the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs
(SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't
load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We
have to assume only one LUN for Fibre Channel because the LUN setting
in Request Queue entries is in different places whether we have SCCLUN
firmware or not, so the only LUN guaranteed to work for both is LUN 0.
Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used-
instead use run time determinants based upon isp->isp_maxluns.
After starting firmware, delay 500us to give it a chance to get rolling.
Fix the interrupt service routine to check for both isr && sema being zero
before thinking this was a spurious interrupt. Following the manuals,
allow for both Mailbox as well as Queue Reponse type interrupts for regular
SCSI.
(we always support fabric now). Remove SCCLUN definition (we always
support SCCLUN now, if we load the f/w). Add typedef definition of an
external firmware fetch function.
need this RSN.
Remove a pointless warning in the root device locating code.
Remove the "wd" compatibility name from the "ad" driver.
WARNING: If you have not updated to use /dev/wd* in your /etc/fstab
and modern bootblocks, it would be a very good idea to do so BEFORE
you upgrade your kernel.
Implement the Solaris way to break into DDB over a serial console
instead of sending a break. Sending the character sequence
CR ~ ^b will break the kernel into DDB (if DDB is enabled).
Reviewed by: peter
layout introduced in driver 1.5.3. The driver was
confused by the bogus TEKRAM table used to translate
user sync. setting to SCSI sync. factor.
Btw, the new TEKRAM DC-390 U3D and U3W Ultra-160
controllers seem to be using BIOS from SYMBIOS/LSI
and thus SYMBIOS NVRAM layout.
If that means that TEKRAM will now offer real
SYMBIOS software compatible SCSI controllers, then
it is a *GREAT NEWS*.
What we'd like to know is whether or not we have a listener
upstream that really hasn't configured yet. If we do, then
we can give a more sensible reply here. If not, then we can
reject this out of hand.
Choices for what to send were
Not Ready, Unit Not Self-Configured Yet
(0x2,0x3e,0x00)
for the former and
Illegal Request, Logical Unit Not Supported
(0x5,0x25,0x00)
for the latter.
We used to decide whether there was at least one listener
based upon whether the black hole driver was configured.
However, recent config(8) changes have made this hard to do
at this time.
Actually, we didn't use the above quite yet, but were sure considering it.
Generated a new macor, RAY_RECERR for reporting errors with. Verbosity set with IFF_DEBUG (recommended at present).
Add PRIBIO to tsleeps.
Catch detach on ray_ccs_alloc a little better.
Move sc_promisc into desired and current n/w parameters.
Remove IFQ_PEEK, we know the driver runs okay without it.
Drain the output queue in ray_stop.
Only use ray_mcast for ADD/DEL multi ioctls. ray_init_multi resets the
multicast list on startup. Simplifies ray_init a little.
Tidy some old comments.
ray_download_done now copies the whole desired n/w parameter set into the
current set. This is because I was missing soem parameters - like the
net type!
2. Newbusify the driver.
3. Build as a module.
4. Use correct minor numbers when creating device files.
5. Correctly lock control characters.
6. Return ENXIO when device not configured.
Submitted by: Tor Egge <Tor.Egge@fast.no>
7. Fix the baud_table.
Submitted by: Elliot Dierksen <ebd@oau.org>
Note:
- the old driver still lives in src/sys/i386/isa, so that you can
revert to it if something goes wrong.
- The module does not detach very well. Attaching works fine.
map physical addresses below 0x2000 (accoding to AMI). If we
allocate our s/g tables and get an address below this point, leak the
memory and try again.
This should fix booting from these controllers.
Get ray_detach working correctly. This is a very simple routine as it
just wakes up sleeping processes. Note that anything woken has NO softc
structure available! runq_add is suitably modified to detect a detach and
return straight away.
Due to ray_detach and its implications use a macro for adding things
to the runq in user land.
tested on Intel BX chipsets only. The other agp minidrivers are totally
untested.
The programming api is a subset of the Linux api and is only intended to
be enough for the X server to use. There is also an in-kernel api for the
use of other kernel modules such as the 3D DRI.