new data is acknowledged, reset the dupacks to 0.
The problem was spotted when a connection had its send buffer full
because the congestion window was only 1 MSS and was not being incremented
because dupacks was not reset to 0.
Obtained from: Yahoo!
1. Correctly handle commands initiated by the adapter. These commands
are defered to a kthread responsible for their processing, then are
properly returned to the controller.
2. Add/remove disk devices when notified by the card that a container was
created/deleted/offline.
3. Implement crashdump functionality.
4. Support all ioctls needed for the management CLI to work. The linux
version of this app can be found at the Dell or HP website. A native
version will be forthcoming.
MFC-after: 4.4-RELEASE
Second, the TI 1130 need to have the PCI_INTR set, not cleared.
This gets Soren's machine working with NEWCARD again.
# The whole initialization is a mess and needs to be organized ala OLDCARD.
the cwd is looked up inside the kernel. The native getcwd() in libc
handles this in userland if __getcwd() fails.
Obtained from: NetBSD via OpenBSD
Tested by: Chris Casey <chriss@phys.ksu.edu>, Markus Holmberg <markush@acc.umu.se>
Reviewed by: Darrell Anderson <anderson@cs.duke.edu>
PR: kern/24315
pollution for non-POSIX.1e macros.
o Introduce CAP_UNITE(), CAP_NONZERO().
o Disable aspects of CAP_SETPCAP, which is Linux-specific (in particular,
remove it from CAP_ALL_ON).
o Improve commenting.
Submitted by: tmm
Obtained from: TrustedBSD Project
KINFO_BSDI_SYSINFO. This supposedly fixes Netscape 3.0.4 (bsdi binary)
on -current. (and is also applicable to RELENG_4)
PR: 25476
Submitted by: Philipp Mergenthaler <un1i@rz.uni-karlsruhe.de>
multiple times, others do. The last strategy, which was to assume
that already routed interrupts were good and just return them doesn't
work for some laptops. So, instead, we have a new strategy: we notice
that we have an interrupt that's already routed. We go ahead and try
to route it, none the less. We will assume that it is correctly
routed, even if the route fails. We still assume that other failures
in the bios32 call are because the interrupt is NOT routed.
Note: some laptops do not support the bios32 interface to PCI BIOS and
we need to call it via the INT 2A interface. That is another windmill
to till at later.
Also correct a minor typo and minor whitespace nits.
Strong MFC candidate.
dual function card. It needs pretty much the same flags as the 656C,
except that it seems to need both the INVERT_MII_PWR and INVERT_LED_PWR
flags set. Tested with cardbus in -current as of today.
Also added support for the 3c656, which looks to be the same as
the 656B, except it doesn't need the EEPROM_8BIT flag. I think. This
one is untested, but the added support should not break any of the
other cards.
to the application as a RST would, this way we're compatible with the most
applications.
MFC candidate.
Submitted by: Scott Renfro <scott@renfro.org>
Reviewed by: Mike Silbersack <silby@silby.com>
I already deleted it some time ago). This should fix problem people have with
unsefined reference to `MD_PRELOAD_COMPRESSED'.
Submitted by: Manfred Antar <null@pozo.com>
the chip can cause a PCI protocol violation in under certain scenarios.
The workaround is to rewrite the EEPROM to disable Dynamic Standby Mode.
Once the EEPROM is rewritten, the system needs to be rebooted in order
to pick up the new settings.
This has been tested on several ICH2/ICH2-M systems, found in 815E based
boards, and usually identified by the presence of the 82562 ET/EM PHY.
Thanks to: Mike Tansca, Paul Saab for samples of the problematic boards.
if all disks were detached sucessfully;
- use consistent style for return statements and fix several others style
inconsistencies.
Reviewed by: ru
Approved by: phk
file. ffs will discard any pending dirty pages when it is closed,
so we may as well not waste time trying to clean them. This doesn't
stop other things from writing it out, eg: pageout, fsync(2) etc.
config space that I'm aware of) work. I'm committing this from such
a machine.
Remove warning about I/O based bridges. Warn users that the PCI routing
of interrupts still doesn't work for these cards.
o For TI PCI-1130, you need to set bit 5 of register 91 if you want
ANY pci interrupts. Then set bits 3 and/or 4 as appropriate. This
will fix those people with 1030, 1130 and 1131 in their machines
trying to do PCI interrupts.
o Fix case where we were trying to automatically fail back to ISA
interrupt routing. We were dereferencing a NULL pointer. This
was true of ANY chipset.
o The bus_setup_intr method needs to be pcic_setup_intr so that "FAST"
interrupts fail on PCI case (modems act flakey if we don't force
them to fall back to normal interrupts). Also needed so that the
proper ISA IRQ can be set in the ExCA register. This fixes the
people whose ISA routing was failing[*].
o When we find a generic yenta/pccard bridge, go ahead and print its
vendor ID in boot verbose.
Machine with theses symptoms and a serial console by: jedgar
[*] Looks like my pc98 machine has some interrupt source on IRQ 15
that gave about 30 interrupts per second, which masked this problem on
my PC-9821Nr15.