consdev structure.
If the consdev name is not set and we have a cn_dev, set the name
from there. Try to issue a printf about this, even though it may
not have a place to go.
Modify the sysctl related code to pick up the name from the consdev
instead.
Most of the actual use of the cn_dev field is merely to get the name,
and most of the actual initializations are bogusly using makedev()
because the probe/attach has not been completed.
Instead we will migrate console drivers to fill in the name and if
the driver needs it: the unit number, thereby avoiding the bogus
calls to makedev().
and the Z8530 drivers used the I/O address as a quick and dirty way to
determine which channel they operated on, but formalizing this by
introducing iobase is not a solution. How for example would a driver
know which channel it controls for a multi-channel UART that only has a
single I/O range?
Instead, add an explicit field, called chan, to struct uart_bas that
holds the channel within a device, or 0 otherwise. The chan field is
initialized both by the system device probing (i.e. a system console)
or it is passed down to uart_bus_probe() by any of the bus front-ends.
As such, it impacts all platforms and bus drivers and makes it a rather
large commit.
Remove the use of iobase in uart_cpu_eqres() for pc98. It is expected
that platforms have the capability to compare tag and handle pairs for
equality; as to determine whether two pairs access the same device or
not. The use of iobase for pc98 makes it impossible to formalize this
and turn it into a real newbus function later. This commit reverts
uart_cpu_eqres() for pc98 to an unimplemented function. It has to be
reimplemented using only the tag and handle fields in struct uart_bas.
Rewrite the SAB82532 and Z8530 drivers to use the chan field in struct
uart_bas. Remove the IS_CHANNEL_A and IS_CHANNEL_B macros. We don't
need to abstract anything anymore.
Discussed with: nyan
Tested on: i386, ia64, sparc64
aic7xxx_pci.c:
When performing our register test, be careful
to avoid resetting the chip when pausing the
controller. The test reads the HCNTRL register
and then writes it back with the PAUSE bit
explicitly set. If the last write to the controller
before our probe is to reset it, the CHIPRST
bit will still be set, so we must mask it off
before the PAUSE operation. On some chip versions,
we cannot access registers for a few 100us after
a reset, so this inadvertant reset was causing PCI
errors to occur on the read to check for paused
status.
Submitted by: gibbs
Reimplement pmap_release() such that it uses the page table rather than
the pte object to locate the page table directory pages. (Temporarily,
retain an assertion on the emptiness of the pte object.)
systems where the data/stack/etc limits are too big for a 32 bit process.
Move the 5 or so identical instances of ELF_RTLD_ADDR() into imgact_elf.c.
Supply an ia32_fixlimits function. Export the clip/default values to
sysctl under the compat.ia32 heirarchy.
Have mmap(0, ...) respect the current p->p_limits[RLIMIT_DATA].rlim_max
value rather than the sysctl tweakable variable. This allows mmap to
place mappings at sensible locations when limits have been reduced.
Have the imgact_elf.c ld-elf.so.1 placement algorithm use the same
method as mmap(0, ...) now does.
Note that we cannot remove all references to the sysctl tweakable
maxdsiz etc variables because /etc/login.conf specifies a datasize
of 'unlimited'. And that causes exec etc to fail since it can no
longer find space to mmap things.
Instead, use EXCA_MEMREG_WIN_SHIFT which is the amount we shift the
bus address by to write into upper memory (eg above 24MB). Use the
latter in this case.
be gone in FreeBSD 6, so put BURN_BRIDGES around it. The TRB also
felt that if something better comes along sooner, it can be used to
replace this code.
Delayed by: BSDcon and subsequent disk crash.
o revamp IPv4+IPv6+bridge usage to match API changes
o remove pfil_head instances from protosw entries (no longer used)
o add locking
o bump FreeBSD version for 3rd party modules
Heavy lifting by: "Max Laier" <max@love2party.net>
Supported by: FreeBSD Foundation
Obtained from: NetBSD (bits of pfil.h and pfil.c)
attached network could exhaust kernel memory, and cause a system
panic, by sending a flood of spoofed ARP requests.
Approved by: jake (mentor)
Reported by: Apple Product Security <product-security@apple.com>
Skinny is the protocol used by Cisco IP phones to talk to Cisco Call
Managers. With this code, one can use a Cisco IP phone behind a FreeBSD
NAT gateway.
Currently, having the Call Manager behind the NAT gateway is not supported.
More information on enabling Skinny support in libalias, natd, and ppp
can be found in those applications' manpages.
PR: 55843
Reviewed by: ru
Approved by: ru
MFC after: 30 days
order to use "unmanaged" pages in the kmem object, vm_map_delete() must
unconditionally perform pmap_remove(). Otherwise, sparc64 has problems.
Tested by: jake
32 bit binary stuff. 32 bit binaries do not like it much when the kernel
tries hard to put things above the 8GB mark.
I have a work-in-progress to fix this properly, but I didn't want to burn
anybody with this yet.
