large to huge amounts of small or medium sized receive buffers. The problem
with these situations is that they eat up the available DMA address space
very quickly when using mbufs or even mbuf clusters. Additionally this
facility provides a direct mapping between 32-bit integers and these buffers.
This is needed for devices originally designed for 32-bit systems. Ususally
the virtual address of the buffer is used as a handle to find the buffer as
soon as it is returned by the card. This does not work for 64-bit machines
and hence this mapping is needed.
ACPI nodes with the plug and play ID's defined for a "Generic ISA Bus
Device" as defined in section 10.7 of the ACPI 2.0 specification. This
gives machines like the Libretto that contain a fake ISA bus that is not
connected via a PCI-ISA bridge an ISA bus for ISA devices to attach to.
Tested by: markm
This is based on the ubsa driver by Alexander Kabaev along with documentation
gleaned from the Linux mct_u232 driver. I've had this driver sitting in my
tree for almost 6 months, and several others have found it useful.
build it on the i386 and alpha architectures, where this has been
set up (there is also a sparc64-bitops.h in sys/gnu/ext2fs, but it
appears to be broken and it is not linked up).
This should unbreak the sparc64 LINT build.
built by LINT. Also override a number of knobs for enabling and
disabling various modules in the ALL_MODULES case to further increase
LINT's module coverage.
Submitted by: ru
redundant paths to the same device.
This class reacts to a label in the first sector of the device,
which is created the following way:
# "0123456789abcdef012345..."
# "<----magic-----><-id-...>
echo "GEOM::FOX someid" | dd of=/dev/da0 conv=sync
NB: Since the fact that multiple disk devices are in fact the same
device is not known to GEOM, the geom taste/spoil process cannot
fully catch all corner cases and this module can therefore be
confused if you do the right wrong things.
NB: The disk level drivers need to do the right thing for this to
be useful, and that is not by definition currently the case.
on friday 13th and without making a universe). This adds struct and
constant definitions for ATM traffic parameters and re-enables the
build of the midway driver.
Tested by: make universe
from the tree until it is fixed. Since it is an atm driver, it isn't
commonly used so this will not negatively impact too many people.
harti can reconnect it when he resurfaces and corrects the en module
problems. This should allow snapshots to start succeeding again.
Reported by: lots of people
It currently supports the PMC Sierra Lite, Ultra and 622 chips and
the IDT 77105. The driver handles media options and state in a consistent
manner for ATM drivers. The next commit to the midway driver will make
it use utopia.
series. This driver was generously developed and released by David
Jeffreys and Adaptec. I've updated it to work with 5.x and fixed a
few bugs.
MFC After: 1 week
* AcpiOsDerivePciId(): finds a bus number, given the slot/func and the
acpi parse tree.
* AcpiOsPredefinedOverride(): use the sysctl hw.acpi.os_name to
override the value for _OS.
Ideas from: takawata, jhb
Reviewed by: takawata, marcel
Tested on: i386, ia64
following changes have been done:
- stylify. The original code was too hard to read.
- get rid of a number of compilation options (Adaptec-only, Eni-only, no-DMA).
- more debugging features.
- locking. This is not correct yet in the absence of interface layer locking,
but is correct enough to not to cause lock order reversals.
- remove RAW mode. There are no users of this in the tree and I doubt that
there are any.
- remove NetBSD compatibility code. There was no way to keep NetBSD non-busdma
and FreeBSD busdma code together.
- if_en now buildable as a module.
This has been actively tested on sparc64 and i386 with ENI server and
client cards and an Adaptec card (thanks to kjc).
Reviewed by: mdodd, arr
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
Many internal structure changes for the FireWire driver.
- Compute CRC in CROM parsing.
- Add support for configuration ROM build.
- Simplify dummy buffer handling.
- busdma conversion
- Use swi_taskqueue_giant for -current. Mark the interrupt routine as MPSAFE.
- AR buffer handling.
Don't reallocate AR buffer but just recycle it.
Don't malloc and copy per packet in fwohci_arcv().
Pass packet to fw_rcv() using iovec.
Application must prepare receiving buffer in advance.
- Change fw_bind API so that application should pre-allocate xfer structure.
- Add fw_xfer_unload() for recycling struct fw_xfer.
- Add post_busreset hook
- Remove unused 'sub' and 'act_type' in struct fw_xfer.
- Remove npacket from struct fw_bulkxfer.
- Don't call back handlers in fwochi_arcv() if the packet has
not drained in AT queue
- Make firewire works on big endian platform.
- Use native endian for packet header and remove unnecessary ntohX/htonX.
- Remove FWXFERQ_PACKET mode. We don't use it anymore.
- Remove unnecessary restriction of FWSTMAXCHUNK.
- Don't set root node for phy config packet if the root node is
not cycle master capable but set myself for root node.
We should be the root node after next bus reset.
Spotted by: Yoshihiro Tabira <tabira@scd.mei.co.jp>
- Improve self id handling
Tested on: i386, sparc64 and i386 with forced bounce buffer
monitors the entropy data harvested by crypto drivers to verify it complies
with FIPS 140-2. If data fails any test then the driver discards it and
commences continuous testing of harvested data until it is deemed ok.
Results are collected in a statistics block and, optionally, reported on
the console. In normal use the overhead associated with this driver is
not noticeable.
Note that drivers must (currently) be compiled specially to enable use.
Obtained from: original code by Jason L. Wright
included in XFree86 4.3, but includes some fixes. Notable changes include
Radeon 8500-9100 support, PCI Radeon/Rage 128 support, transform & lighting
support for Radeons, and vblank syncing support for r128, radeon, and mga.
The gamma driver was removed due to lack of any users.
permit users and groups to bind ports for TCP or UDP, and is intended
to be combined with the recently committed support for
net.inet.ip.portrange.reservedhigh. The policy is twiddled using
sysctl(8). To use this module, you will need to compile in MAC
support, and probably set reservedhigh to 0, then twiddle
security.mac.portacl.rules to set things as desired. This policy
module only restricts ports explicitly bound using bind(), not
implicitly bound ports where the port number is selected by the
IP stack. It appears to work properly in my local configuration,
but needs more broad testing.
A sample policy might be:
# sysctl security.mac.portacl.rules="uid:425:tcp:80,uid:425:tcp:79"
This permits uid 425 to bind TCP sockets to ports 79 and 80. Currently
no distinction is made for incoming vs. outgoing ports with TCP,
although that would probably be easy to add.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
turns runs its tasks free of Giant too. It is intended that as drivers
become locked down, they will move out of the old, Giant-bound taskqueue
and into this new one. The old taskqueue has been renamed to
taskqueue_swi_giant, and the new one keeps the name taskqueue_swi.
time and there's no indication that it will improve anytime soon.
By removing support for SimOS it is possible to build LINT on
Alpha, which is considered more important at the moment.
Not objected to on: alpha@
for the agp module, and add agp to the list of modules to compile for alpha.
Add an alpha_mb() to agp_flush_cache for alpha -- it's not correct but may
improve the situation, and it's what linux and NetBSD do.
we have the rc4 code already in the kernel (via wlan stuff or awi).
Add a dependency on the rc4 module so if it doesn't exist then load it.
Reviewed by: archie
IP fast forwarding, SIOCGIFADDR, setting hardware address (not currently
enabled in cm driver), multicasts (experimental)
- add ARC_MAX_DATA, use IF_HANDOFF, remove arc_sprintf() and some unused
variables
- if_simloop logic is made more similar to ethernet
- drop not ours packets early (if we are not in promiscous mode)
Submitted by: mark tinguely (partially)
Interface (SMAPI) BIOS, which is present on some IBM
Thinkpad models (560, 600, 770 to name a few.)
The SMAPI BIOS provides access to System Information,
System Configuration, and Power Management.
