o If a prompt is executing the command, only display the warning to
that prompt
o If a prompt is executing a ``load'' command, display the warning
to all prompts *and* syslog
o Otherwise, display the warning to all prompts *and* syslog.
the Davicom DM9100 and DM9102 chipsets, including the Jaton Corporation
XPressNet. Datasheet is available from www.davicom8.com.
The DM910x chips are still more tulip clones. The API is reproduced
pretty faithfully, unfortunately the performance is pretty bad. The
transmitter seems to have a lot of problems DMAing multi-fragment
packets. The only way to make it work reliably is to coalesce transmitted
packets into a single contiguous buffer. The Linux driver (written by
Davicom) actually does something similar to this. I can't recomment this
NIC as anything more than a "connectivity solution."
This driver uses newbus and miibus and is supported on both i386
and alpha platforms.
SiS 900 and SiS 7016 PCI fast ethernet chipsets. Full manuals for the
SiS chips can be found at www.sis.com.tw.
This is a fairly simple chipset. The receiver uses a 128-bit multicast
hash table and single perfect entry for the station address. Transmit and
receive DMA and FIFO thresholds are easily tuneable. Documentation is
pretty decent and performance is not bad, even on my crufty 486. This
driver uses newbus and miibus and is supported on both the i386 and
alpha architectures.
(LCP/CCP/IPCP), one for urgent IP traffic and one for
everything else.
o Add the ``set urgent'' command for adjusting the list of
urgent port numbers. The default urgent ports are 21, 22,
23, 513, 514, 543 and 544 (Ports 80 and 81 have been
removed from the default priority list).
o Increase the buffered packet threshold from 20 to 30.
o Report the number of packets in the IP output queue and the
list of urgent ports under ``show ipcp''.
Supply RAD_NAS_IDENTIFIER if we have a `hostname` and
RAD_IP_ADDRESS if that hostname resolves.
Supply RAD_NAS_PORT using the ttyslot() of the tty that
we're authenticating on if it's a tty device.
Partially submitted by: Andriy I Pilipenko <bamby@marka.net.ua>
PR: 12225
I backed-out the changes in -current and didn't touch stable at all (I
thought I had my patch order reversed, not what actually happened).
AIEEE! I can't even blame the crack for this one since I broke my
crack pipe a few weeks ago. I think sleep deprivation gets the blame
for this one.
Medal for noticing this one goes to: Jim Bloom <bloom@acm.org>
bringing in DHCP support. The only thing I left out were Poul-Henning's
newfs changes since I'm not sure if he's brought the rest of that support
into -stable yet. If it turns out that this is the case, I'll MFC those
changes too.
going to remove ppp from the installation options in 5 days if ppp is
still broken, however, as it hasn't worked at installation time
for several weeks now and it's only causing people to fill my mailbox
with questions.
in NMEA mode (without date).
Trimble OEM Ace-II receiver. Low cost PCB with single
voltage input, external active antenna and two serial
ports with either NMEA and ITAPs output. Programmable
to be tuned for 'time' accuracy in fixed station config.
Author of tool notified.
Submitted by: Dirk van Gulik <dirk.vangulik@jrc.it>
in source input if the -f flag is used, and modify Makefile.yp to only
use -f for the passwd, master.passwd and group maps. These should be
the only ones for which the + and - characters have special meaning
that make it important for us to avoid letting them into any of the map
databases. In some cases (namely the automounter maps) we have to allow
at least the - character through in order to create the map properly.
This closes PR #8699.
