handler in Linux emulation. According to bde, this is what Linux
does.
Recent versions of linuxthreads use %gs for thread-specific data,
while FreeBSD uses %fs (mostly because WINE uses %gs).
Tested by: drew
KASSERT when vp->v_usecount is zero or negative. In this case, the
"v*: negative ref cnt" panic that follows is much more appropriate.
Reviewed by: mckusick
fail due to witness exhausting its internal resources and shutting down.
Reported by: Szilveszter Adam <sziszi@petra.hos.u-szeged.hu>
Tested by: David Wolfskill <david@catwhisker.org>
much more often that expected and negatively impact performance when
running at 100mbps. I need to figure out if there's a better way to
handle this, but for now this shouldn't hurt anything.
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
a LinkSys card here in the office where reading the station address
fails the first time, but works find afterwards. Without this, the
probe fails. I don't think this will negatively impact any existing
cards, but I want to confirm this before MFC'ing.
safe from preemption and concurrent access to the LDT.
- Move the prototype for i386_extend_pcb() to <machine/pcb_ext.h>.
Reviewed by: silence on -hackers
we need to delete the info from the list as well as zero out the res
pointer we saved in the code.
Also made a few style(9) changes while I was at it. Don't use if
(ptr) or if (!ptr), but compare against NULL. Compare against NULL
rather than 0. Don't have useless blocks.
There are likely other problems as well, but at least the wi based
wireless card with memory listed in its cis doesn't panic the system
when the card is inserted.
use TAILQ macros. The sk_attach_xmac() routine calls sk_init_xmac()
before doing the transceiver probe, but *before* ether_ifattach()
is called. This causes sk_init_xmac() to call sk_setmulti(), which
tries to do a TAILQ_FOREACH(), which it can't do because ether_ifattach()
hasn't done a TAILQ_INIT() yet. This causes a NULL pointer dereference
and panic in sk_setmulti() at driver load/initialization time.
Fixed by calling ether_ifattach() before the MII probe.
The code in RELENG_4 still uses the old way of enumerating the
multicast list and doesn't have this problem. Yet.
Reduce the verbose memory map setup reports and work with pccardd to
set the common memory map up.
Use enumeration values for CARD_SET_RES_FLAGS.
Use DELAY when spinning waiting for the card to come free instead of a loop.
MFC: after 1 week
machdep.pccard.pcic_mem_start
machdep.pccard.pcic_mem_end
and default the range to IOM_BEGIN/IOM_END.
This may prove useful to if_ray users (and others) on more modern
hardware that maps BIOS stuff into 0xd000-0xdffff.
MFC: after 1 week
Approved by: imp
The pipe code could not handle running out of kva, it would panic
if that happened. Instead return ENFILE to the application which
is an acceptable error return from pipe(2).
There was some slightly tricky things that needed to be worked on,
namely that the pipe code can 'realloc' the size of the buffer if
it detects that the pipe could use a bit more room. However if it
failed the reallocation it could not cope and would panic. Fix
this by attempting to grow the pipe while holding onto our old
resources. If all goes well free the old resources and use the
new ones, otherwise continue to use the smaller buffer already
allocated.
While I'm here add a few blank lines for style(9) and remove
'register'.
Tidy up includes, credit Slawa Olhovchenkov, John Prince and Eric Hernes
for their efforts and add a couple of missing parenthesis around return
expressions.
that are committed to being freed and reflect these blocks in the
counts returned by statfs (and thus also by the `df' command). This
change allows programs such as those that do news expiration to
know when to stop if they are trying to create a certain percentage
of free space. Note that this change does not solve the much harder
problem of making this to-be-freed space available to applications
that want it (thus on a nearly full filesystem, you may still
encounter out-of-space conditions even though the free space will
show up eventually). Hopefully this harder problem will be the
subject of a future enhancement.
