Force alphas to prefer mem mapping as the default.
Basically, we have a pointer to a function which we can call which will
return us a pointer to firmware for the card we have. We call this function
(if it's non-NULL) with the address of our mdvec f/w pointer.
The way this works is that if ispfw (as a module or a static) is loaded,
it initializes the pointer in isp_pci, so we can call into to it to fetch
a pointer to a f/w set.
If ispfw is MOD_UNLOADed, it's retained a pointer to our mdvec f/w pointers,
which then get zeroed out so we don't have any references to data that's
now gone from kernel memory. Removing the f/w saves ~360KBytes.
Alas, there is no autounload mechanism that works for is here.
tested on Intel BX chipsets only. The other agp minidrivers are totally
untested.
The programming api is a subset of the Linux api and is only intended to
be enough for the X server to use. There is also an in-kernel api for the
use of other kernel modules such as the 3D DRI.
21143 chips, I accidentally removed the DC_MII_REDUCED_POLL flag
for all 21143 cards. This caused problems with timer-instigated
TCP retransmits, which happened to occur at the same time as an
MII poll tick on MII-based cards (e.g. D-Link DFE-570TX). Fixed this,
plus made some other cleanups. The autoneg fixes for the non-MII
cards still work. Also tested the PNIC II now that I have one again.
after autoneg so we make sure to set the link state and duplex mode
correctly.
- Make sure to set the 'ignore pause frames' bit on the XMAC.
- Small linewrap fix.
workalike chips (Macronix 98713A/98715 and PNIC II). Timing is somewhat
critical: you need to bring the link as soon as possible after NWAY
is done, and the old one second polling interval was too long. Now
we poll every 10th of a second until NWAY completes (at which point
we return to the 1 second interval again to keep an eye on the link
state).
I tested all the other cards I had on hand to make sure I didn't bust
any of them and they seem to work (including the MII-based 21143 card).
This should fix some autoneg problems with DE500-BA cards and the
built-in 10/100 ethernet on some alpha systems.
(Now before anyone asks why I never noticed this before, the old code
worked just find with the Intel swich I used for testing back in NY.
Apparently not all switches are as picky about the timing.)
"options COMPAT_OLDPCI". This option already existed, but now also tidies
up the declarations in #include <pci/pci*.h>. It is amazing how much stuff
was using the old pre-FreeBSD 3.x names and going silently undetected.
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
for transmit to the adapter, not when we receive a transmit interrupt
indicating that they were sent. This fix now allows tcpdump to produce
sane results by recording the timestamp at the point where the mbuf was
actually transmitted.
the case where we receive a packet that wraps from the end of the
RX buffer back to the start. This fixes an unaligned access trap on
the alpha with NFS.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
not u_long. On i386's with 64-bit longs, returning u_longs indirectly
in (more than) the space reserved for uintptr_t's tended to corrupt the
previous frame pointer in the stack frame, so it was not easy to debug.
The type mismatches are hidden by the bogus cast in DEVMETHOD().
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
- Break out the support for the XMAC II's PHY into an miibus driver.
- Reorganize the probe/attach stuff using newbus. Each XMAC is now
attached to the parent GEnesis controller using newbus. This is
necessary since each XMAC must also have an attached miibus, and
the miibus read/write register routines need to be able to get
at the softc struct for each XMAC, not the one for the parent
controller. This allows me to get rid of the grotty code I added
for selecting the unit numbers for the ifnet interfaces: the unit
numbers are now derived from the newbus-assigned unit numbers,
which should track with the ifnet interface numbers. I think.
At the very least, there should never be any collisions.
- Add support for the SK-9821 and SK-9822 1000baseTX adapters. Special
thanks to SysKonnect for loaning me two adapters for testing.
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
This don't hurt anything.
PCI/CardBus Bridge -> PCI-CardBus Bridge
Submitted by: Takeshi Shibagaki <sibagaki@lsi.melco.co.jp>
Obtained from: bsd-nomads ML in Japan
- Only call m_pullup() when necessary.
- Check return value from rl_encap() in rl_start() to avoid panic when
we run out of mbufs. (Fixes PR kern/17582)
PR: kern/17582
address size that is different than the standard 6bits. This fixes
support for the Compaq NC3121 card, certain newer Intel Pro/100+
cards, and should also fix integrated NICs on SuperMicro and Compaq
motherboards.
The auto-sizing algorithm was taken from NetBSD (thanks!), which I
think got it from Linux originally.
Thanks also to Andrew Sparrow <spadger@best.com> and Joe Moore
<jomor@ahpcns.com> for supplying me with unworking Compaq and Intel
cards to develop and test the fixes with.
cardbus bridge init routine for all cardbuses. This routine attempts
to compensate for BIOSes that do not setup the cardbus bridge into
legacy mode. Since this is becoming more common, and cardbus pci
cards have appeared on the market, this makes sense.
Do some TI113x specific initialization. This came in as part of the
patch. Report TI1[1234]XX specific config registers protected by
bootverbose.
Minor code cleanup while I'm here. I've also removed the unused code
present in the original patches, and cleaned it up slightly in places
as well.
The original patches supported more than one card, but these patches
support just one. We should likely revisit this in the future.
This makes the Compaq card that Walnut Creek CD purchased for me work
in my bouncer box.
This is a MFC candidate. However, I'd like to get some airtime on
these patches on as many laptops as possible before doing the MFC. It
does change things somewhat. In theory, apart from the minor TI
tweaks, this shouldn't change anything if the bridge is in legacy mode
already.
Submitted by: sanpei@sanpei.org (MIHIRA Yoshiro)
Make the public interface more systematically named.
Remove the alternate method, it doesn't do any good, only ruins performance.
Add counters to profile the usage of the 8 access functions.
Apply the beer-ware to my code.
The weird +/- counts are caused by two repocopies behind the scenes:
kern/kern_clock.c -> kern/kern_tc.c
sys/time.h -> sys/timetc.h
(thanks peter!)
it's options COMPAT_OLDISA and COMPAT_OLDPCI. This is meant to be a
fairly strong incentive to update the older drivers to newbus, but doesn't
(quite) leave anybody hanging with no hardware support. I was talking with
a few folks and I was encouraged to simply break or disable the shims but
that was a bit too drastic for my liking.
platform we're running on so we know how many bits to reserve at the top
end for the 'hose' value. It turns out that there's *just* enough room
to support all possible hoses on TurboLaser.
Reviewed by: gallatin@freebsd.org, dfr@free3bsd.org
from useful drivers such as the 3D DRI drivers I will be porting for
hardware accelerated OpenGL. The hardware will still be reported during
boot using the nomatch system.
Approved by: jkh
the PIRQD bit.
This fixes the problem of uhub0 hanging forever during boot when USB
keyboard support is switched on in the BIOS on motherboards with Intel
chipsets (UHCI).
Approved by: The Sheep
conversion to eliminate the compatability shims without making any
significant changes. This eliminates the shim warnings.
Obtained from: n_himba (tweaked by me, don't blame him for this)
Approved by: jkh
bus_delete_resource.
Fixes a problem when the probe succeeded, but the attach failed. The
release of the resources was done inproperly.
Approved by: jkh
are using an old unconverted driver. Most (if not all) of the drivers
for common hardware are newbus these days. However, we don't want
to encourage people to take the easy way out and write new drivers
using the shims. This is just passive "encouragement".
Reviewed by: phk
the receive code so that it correctly chains receive descriptors together
and handles the case that only a part of a packet is done at the time
we get here.
This is just to make sure we initialize the chip correctly: we need to
make the sure the port select bit in CSR6 is set properly so that we
use the internal PHY for 10/100 support. (The eval boards I have also
include an external HomePNA PHY, but I need to play with that more
before I can support it.)
Collect together the components of several drivers and export eisa from
the i386-only area (It's not, it's on some alphas too). The code hasn't
been updated to work on the Alpha yet, but that can come later.
Repository copies were done a while ago.
Moving these now keeps them in consistant place across the 4.x series
as the newbusification progresses.
Submitted by: mdodd
packets into a single buffer, and set the DC_TX_COALESCE flag for the
Davicom DM9102 chip. I thought I had escaped this problem, but... This
chip appears to silently corrupt or discard transmitted frames when
using scatter/gather DMA (i.e. DMAing each packet fragment in place
with a separate descriptor). The only way to insure reliable transmission
is to coalesce transmitted packets into a single cluster buffer. (There
may also be an alignment constraint here, but mbuf cluster buffers are
naturally aligned on 2K boundaries, which seems to be good enough.)
The DM9102 driver for Linux written by Davicom also uses this workaround.
Unfortunately, the Davicom datasheet has no errata section describing
this or any other apparently known defect.
Problem noted by: allan_chou@davicom.com.tw
makes it a little easier to notice that parity checking an 8bit sram
isn't working.
Turn on scb and internal data-path parity checking for all pci chips types.
We were only doing this for ultra2 chips.
After clearing the parity interrupt status, clear the BRKADRINT. This
avoids seeing a bogus BRKADRINT interrupt after external SCB probing
once normal interrupts are enabled.
controllers will run at U2 speeds until I can complete the U160 support
for this driver.
Correct a termination buglet for the 2940UW-Pro.
Be more paranoid in how we probe and enable external ram, fast external
ram timing and external ram parity checking. We should now work on
20ns and 8bit SRAM parts.
Perform initial setup for the DT feature on cards that support it.
Factorize and clean up code. Use tables where it makes sense, etc.
Add some delays in dealing with the board control logic. I've never
seen this code fail, but with the ever increasing speed of processors,
its better to insert deterministic delays just to be safe. This stuff
is only touched during probe and attach, so the extra delay is of no
concern.
driver seems relatively functional, but could use some souping up,
particularly in the performance area. This has both NetBSD and FreeBSD
attachment code and a fair amount of effort has been put into making
it easy to port to different *BSD platforms.
The basic design is a one tfd per mbuf transmit (with no transmit
related interrupts- tfds are gc'd as needed). The receive ring
uses a 2K buffer per rfd with a +2 byte adjust for the ethernet
header (so the payload is aligned). There's support that *almost*
works for doing large packets- the rfd chaining code works, but there's
some problem with getting good checksums at the IP reassembly level
(ditto for doing short tfd's too).
The chip has support for TCP checksums insertion for transmit and
TCP checksum calculation on receive (for both you have to do some
appropriate backoff && twiddling), but this isn't in place.
This is nearly entirely reverse engineered from the released Intel
driver, so there's a lot of "We have to do this but do not know why"
stuff. There is somebody who has the chip specs who works in FreeBSD
but they're being a bit standoffish about even sharing hints which
is somewhat annoying. It's also apparent that all I had to work with
were the first rev boards.
This driver has been lightly tested on intel && alpha, but only
point-to-point. There may be some issues with switches- use of
boot time environment variables that override EEPROM settings
(e.g., 'set wx_ilos=1' which inverts the sense of optical signal
loss) may help with this.
I had this out for review for three weeks, and nobody said anything
negative or positive, ergo, this checkin has no 'reviewed by' field
which I would have preferred.
down, the dc driver and receiver can fall out of sync with one another,
resulting in a condition where the chip continues to receive packets
but the driver never notices. Normally, the receive handler checks each
descriptor starting from the current producer index to see if the chip
has relinquished ownership, indicating that a packet has been received.
The driver hands the packet off to ether_input() and then prepares the
descriptor to receive another frame before moving on to the next
descriptor in the ring. But sometimes, the chip appears to skip a
descriptor. This leaves the driver testing the status word in a descriptor
that never gets updated. The driver still gets "RX done" interrupts but
never advances further into the RX ring, until the ring fills up and the
chip interrupts again to signal an error condition. Sometimes, the
driver will remain in this desynchronized state, resulting in spotty
performance until the interface is reset.
Fortunately, it's fairly simple to detect this condition: if we call
the rxeof routine but the number of received packets doesn't increase,
we suspect that there could be a problem. In this case, we call a new
routine called dc_rx_resync(), which scans ahead in the RX ring to see
if there's a frame waiting for us somewhere beyond that the driver thinks
is the current producer index. If it finds one, it bumps up the index
and calls the rxeof handler again to snarf up the packet and bring the
driver back in sync with the chip. (It may actually do this several times
in the event that there's more than one "hole" in the ring.)
So far the only card supported by if_dc which has exhibited this problem
is a LinkSys LNE100TX v2.0 (82c115 PNIC II), and it only seems to happen
on one particular system, however the fix is general enough and has low
enough overhead that we may as well apply it for all supported chipsets.
I also implemented the same fix for the 3Com xl driver, which is apparently
vulnerable to the same problem.
Problem originally noted and patch tested by: Matt Dillon
probes are at the 'chip' level and will get overridden by pcic_p if it is
compiled in. It's still nice to get the better probe message if it's not...
Requested by: imp
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
frames would be handled incorrectly due to bad usage of m_pullup() in
the case where the frame wraps from the end of the receive buffer back
the beginning.
Also, when manually extending small packets to pad them to the minimum
frame length during transmission, zero out the pad area to make some
really paranoid people happy.
the 3c450-TX HomeConnect. Like the 3cSOHO100-TX OfficeConnect, this NIC
uses the same ASIC as the 3c905B/3c905C but is targeted for a particular
market segment (home users). It is somewhat less expensive than the
3c905B/3c905C ($49, according to the 3Com web site), comes with its
own custom driver kit and is bundled with various goofy Windows software
packages designed to demonstrate the niftyness of home networking (networked
game demos, etc...).
Changes are:
- Add PCI ID to list in if_xlreg.h.
- Update xl_devs table in if_xl.c.
- Update xl_choose_xcvr() to consider the HomeConnect the
same as all the other 10baseT/100baseTX cards.
- Add a flag DC_TX_INTR_ALWAYS which causes the transmit code to
request a TX done interrupt for every packet. The PNIC seems to need
this to insure that the sent TX buffers get reaped in a timely fashion.
- Try to unreset the SIA as soon as possible after resetting the whole
chip.
- Change dcphy to support either 10/100 or 10Mbps only NICs. The
built-in 21143 ethernet in Compaq Presario machines is 10Mbps only
and it doesn't work right if we try to advertise 100Mbps modes during
autoneg. When restricted to only 10mbps modes, it works fine.
Note that for now, I detect this condition by checking the PCI
subsystem ID on this NIC (which has a Compaq vendor/device ID).
Yes, I know that's what the SROM is supposed to be for. I'm deliberately
ignoring the SROM wherever possible. Sue me.
The latter two fixes allow if_dc to work correctly with the built-in
ethernet on certain Compaq Presario boxes. There are liable to be quite
a few people using these as their home systems who might want to try
FreeBSD; may as well be nice to them.
Now if anybody out there has an Alpha miata with 10Mbps ethernet and
can show me the output from pciconf -l on their system, I'd be grateful.
used to edit the old-style isa_devtab config tables to insert a mapping
for a pci device into the isa tables so that the wdc driver could probe
it later. This has been #if 0'd since April.
attaching to the device via chip*, use the newbus nomatch method to report
the device. This leaves them unattached so that a driver can be easily
loaded to grab them later.
background ]
Rename sys/pci/pci_ioctl.h to sys/sys/pciio.h to make it easier for
userland programs to use this interface. Reformat the file, and add a
BSD-style copyright to it.
Add a new man page for pci(4). The PCIOCGETCONF, PCIOCREAD, and PCIOCWRITE
ioctls are documented, but the PCIOCATTACHED ioctl is not documented
because it is not implemented.
Change includes of <pci/pci_ioctl.h> to <sys/pciio.h> or remove them
altogether. In many cases, pci_ioctl.h was unused.
Reviewed by: steve
- Convert to using TX descritor polling similar to the xl driver (the
ST201 is a clone of the 3c90xB chipset and offers the same transmit
polling scheme). This should reduce TX overhad a little.
- Make sure to reset PHY when switching mode, as in the starfire driver.
- Fix instances of free() that should be contigfree().
- Remove dead code.
case. The idea is to reduce how often we call mii_tick(), however currently
it may not be called often enough, which prevents autonegotiation from
being driven correctly.
This should improve the chances of successfully autonegotiating media
settings on non-MII 21143 NICs. (Still waiting for confirmation from
some testers, but the code is clearly wrong in any case.)
Don't arbitrarily limit the initiator ID of the card to something <= 7.
Fix a bug in the checksum code that would incorrectly prevent a valid
checksum of zero. (cp)
Don't touch rely on seeprom data when configuring termination. We may
not have seeprom data. (cp)
Treat all ULTRA2 capable adapters the same way when reading or writing
the BRDCTL register. We previously only did this correctly for aic7890/91
chips. This should correct some problems with termination settings on
aic7896/97 adapters. (cp)
Changes marked with "(cp)"
Pointed out by: Chuck Paterson <cp@bsdi.com>
before selecting a mode. The Seeq PHY chips on the Adaptec cards that
use the AIC-6915 controller seem to need it in order to get them to
change modes correctly.
This corrects a problem that I noticed where my ANA-62022 board failed
to correctly program the full duplex bit in the macconfig1 register
when the interface was brought up. Running ifconfig sf0 would mask this
problem in some cases because polling the PHY status would cause the
miibus code to notice that full duplex was now needed and the statchg
callback would be invoked to configure the duplex setting. However it
would still get it wrong other times.
Also changed sf_miibus_statchg() to program the IPG register to match
the duplex setting in accordance with Adaptec manual's recommendations
(0x15 for full duplex, 0x11 for half duplex).
which it replaces. The new driver supports all of the chips supported
by the ones it replaces, as well as many DEC/Intel 21143 10/100 cards.
This also completes my quest to convert things to miibus and add
Alpha support.
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
by identifying the version in the PCI drivers.
The OHCI driver just presets this to 1.0 as it is not specified in the
PCI registers anywhere. This should be revisited once USB 2.0 is in
wide spread use.
rather than an "it's mine!" so that other newbus-aware drivers can
bid for the device too. This should allow the sym driver to out-bid
the ncr driver for devices it supports without having to modify ncr.c
at all. ncr would then function as a catch-all.
parameter a char ** instead of a const char **. This make these
kernel routines consistent with the corresponding libc userland
routines.
Which is actually 'correct' is debatable, but consistency and
following the spec was deemed more important in this case.
Reviewed by (in concept): phk, bde
pci_probe_nomatch, so it won't be in the way when loading USB as a module.
The reason for them being there in the first place is that every
motherboard comes with USB kit and this way it looks more pretty (peter).
The real solution will be to define some method of detaching a driver
after it has attached.
out of the PCI CLASS reg and store it in the softc. Use the getenv_quad
function to get a WWN override from the environment. Look for a config
value for same. Make slightly less lame the wwn seed construction.
is documented to be 0x18 in the Adaptec manual, however there appears to
be a newer board rev with code 0x19. I added a #define for this and
updated the probe code so that this board will be properly identified
in the probe messages. (Currently it's just identified generically as
an AIC-6915 chip.)
"rw" argument, rather than hijacking B_{READ|WRITE}.
Fix two bugs (physio & cam) resulting by the confusion caused by this.
Submitted by: Tor.Egge@fast.no
Reviewed by: alc, ken (partly)
