TS_WOPEN state when CLOCAL is toggled from on to off while there
is no carrier. There is no way back, and with sio there is no way
forward either (TS_ISOPEN will never be set again for the current
open). This bug was observed in 1.1 and was fixed in 1.1.5.
`depend' wasn't supported. This seems to have only broken `make depend'
in gnu/usr.bin/ld.
bsd.prog.mk:
Build the man pages in ${MANDEPEND} at build time.
isn't important; it is only used to prevent symlink loops from looping
forever. 32 is a quite reasonable default.
Submitted by: Ed Hudson <elh@p5.spnet.com>
1. add iosize command, and show it in `ls'
2. add a probe command
3. add an attach command
[the latter 2 do the obvious thing - call the device's routine and print the
status returned].
You will normally have to have a VLB or other 32bit IDE "controller" for
this to work.
Depending on your setup, this may gain you 20-100 % speed from your disk.
Reviewed by: phk
Submitted by: vak@cronyx.ru
message instead of relying on the fact that we are scheduled to send them.
The old method worked 99.9% of the time, but someone reported some periferals
that did MSG_REJECT at odd times (sometimes before we could send an SDTR
or WDTR) that we would construe as the response to an SDTR or WDTR message.
This also removes a possible race condition where after a bus reset (the
result of a command time out not during intial probe time), we might queue
two commands both requesting SDTR, WDTR or both.
in serious system instability. Changed a B_INVAL to a B_NOCACHE so that
buffer data is properly disposed of.
Submitted by: John Dyson, Rick Macklin, and ohki@gssm.otsuka.tsukuba.ac.jp
definitions taken from the PCI specs. Part of them were typed
in by Wolfgang Stanglmeier, the (at that time unneeded) rest
by Charles Hannum (thanks !).
may be the result of reselect following too fast for
the driver to notice. Not the final solution, but the
problem has been seen only with very few devices.
Reviewed by: se
Submitted by: wolf (Wolfgang Stanglmeier)
Fixed long standing bug in freeing swap space during object collapses.
Fixed 'out of space' messages from printing out too often.
Modified to use new kmem_malloc() calling convention.
Implemented an additional stat in the swap pager struct to count the
amount of space allocated to that pager. This may be removed at some
point in the future.
Minimized unnecessary wakeups.
vm_fault.c:
Don't try to collect fault stats on 'swapped' processes - there aren't
any upages to store the stats in.
Changed read-ahead policy (again!).
vm_glue.c:
Be sure to gain a reference to the process's map before swapping.
Be sure to lose it when done.
kern_malloc.c:
Added the ability to specify if allocations are at interrupt time or
are 'safe'; this affects what types of pages can be allocated.
vm_map.c:
Fixed a variety of map lock problems; there's still a lurking bug that
will eventually bite.
vm_object.c:
Explicitly initialize the object fields rather than bzeroing the struct.
Eliminated the 'rcollapse' code and folded it's functionality into the
"real" collapse routine.
Moved an object_unlock() so that the backing_object is protected in
the qcollapse routine.
Make sure nobody fools with the backing_object when we're destroying it.
Added some diagnostic code which can be called from the debugger that
looks through all the internal objects and makes certain that they
all belong to someone.
vm_page.c:
Fixed a rather serious logic bug that would result in random system
crashes. Changed pagedaemon wakeup policy (again!).
vm_pageout.c:
Removed unnecessary page rotations on the inactive queue.
Changed the number of pages to explicitly free to just free_reserved
level.
Submitted by: John Dyson
argument is now more than just a single flag. (kern_malloc.c)
Used new M_KERNEL value for socket allocations that previous were
"M_NOWAIT". Note that this will change when we clean up the M_ namespace
mess.
Submitted by: John Dyson
some comparisons as it is more correct (we want the kernel page tables
included).
Reorganized some of the expressions for efficiency.
Fixed the new pmap_prefault() routine - it would sometimes pick up the
wrong page if the page in the shadow was present but the page in object
was paged out. The routine remains unused and commented out, however.
Explicitly free zero reference count page tables (rather than waiting
for the pagedaemon to do it).
Submitted by: John Dyson
Submitted by: wolf (Wolfgang Stanglmeier)
Most PCI specific files moved from sys/i386/pci to sys/pci.
One PC specific file (pcibus.c) new in sys/i386/isa.
Submitted by: wolf (Wolfgang Stanglmeier)
Obtained from:
Most PCI specific files moved from sys/i386/pci to sys/pci.
One PC specific file (pcibus.c) new in sys/i386/isa.
Now it matches the man page and also the only other commercial implementation
i have found so far ( Solaris 2.x).
Changed the name from ss_base to ss_sp.
Display update method changed, now allways write in memory buffer,
then periodically update physical display.
Speed improvements (now > 5 times faster than the old syscons).
History now circular buffer, with changeable size.
History scroll by up/down line, up/down page, home and end.
Backtab proberly implemented.
Now space for 96 function keys, 63 allocated standard, default now
SCO/SYSV compat again as in the old days.
New keyboard definition files ~share/syscons/keymaps/*
Misc fixes for old "hacks" that broke SCO/SYSV compat.
More that I forgot before writing this...
Handles at least Trantor T130 and ProAudioSpectrum adapters.
The pas driver has consequently been removed.
This driver can be configured without without interrupts.
Manpage to follow when PAS16 has been edited in.
Reviewed by: phk
Submitted by: Serge Vakulenko, <vak@cronyx.ru>
case, software cursor now optional case. Driver must provide
raw things (what hardware do for us, exactly) as default case,
all driver features must be _optional_. Modern VGAs have internal
configuration utilities to set cursor shape/blinking which stored
into cards ROM, and syscons nuke out such features completely
by forcing software cursor. Moreover, software cursor is hard
to distinguish on standouted (or near standouted) fields and
tends to disappearse from the screen.
Set "flags 0x4" to enable software cursor now.
o Cleanup screen savers.
o Don't draw cursor if saver or blinker is active.
o Duplicated code moved to functons.
o Add more checks for blinker in progress, character lost otherwise
when blinker restore old contents.
o Reduce blinking counter to 3, too slow in old variant.
o Fix timeout code in scrn_timer(), old variant can reenter iself,
if action takes too long time.
o Disable visual bell for scroll lock mode, saved screen
becomes overwritted otherwise.
(Boot with the -D flag if you want symbols.)
Make it easier to extend `struct bootinfo' without losing either forwards
or backwards compatibility.
ddb_aout.c:
Get the symbol table from wherever the loader put it.
Nuke db_symtab[SYMTAB_SPACE].
boot.c:
Enable loading of symbols. Align them on a page boundary. Add printfs
about the symbol table sizes.
Pass the memory sizes to the kernel.
Fix initialization of `unit' (it got moved out of the loop).
Fix adding the bss size (it got moved inside an ifdef).
Initialize serial port when RB_SERIAL is toggled on.
Fix comments.
Clean up formatting of recently added code.
io.c:
Clean up formatting of recently added code.
netboot/main.c, machdep.c, wd.c:
Change names of bootinfo fields.
LINT:
Nuke SYMTAB_SPACE.
Fix comment about DODUMP.
Makefile.i386:
Nuke use of dbsym.
Exclude gcc symbols from kernel unless compiling with -g.
Remove unused macro.
Fix comments and formatting.
genassym.c:
Generate defines for some new bootinfo fields. Change names of old ones.
locore.s:
Copy only the valid part of the `struct bootinfo' passed by the loader.
Reserve space for symbol table, if any.
machdep.c:
Check the memory sizes passed by the loader, if any. Don't use them yet.
bootinfo.h:
Add a size field so that we can resolve some mismatches between the loader
bootinfo and the kernel boot info. The version number is not so good for
this because of historical botches and because it's harder to maintain.
Add memory size and symbol table fields. Change the names of everything.
Hacks to save a few bytes:
asm.S, boot.c, boot2.S:
Replace `ouraddr' by `(BOOTSEG << 4)'.
boot.c:
Don't statically initialize `loadflags' to 0. Disable the "REDUNDANT"
code that skips the BIOS variables. Eliminate `total'. Combine some
more printfs.
boot.h, disk.c, io.c, table.c:
Move all statically initialzed data to table.c.
io.c:
Don't put the A20 gate bits in a variable.
There is similar bogusness in the pageout daemon that will be fixed soon.
This fixes a panic pointed out to me by Bruce Evans that occurs when
/dev/mem is used to map managed memory.
in the PCnet/Lance family.
Fix attach so 32 bit cards don't call isa_dmacascade.
Add a workaround for 32 bit chips which incorrectly truncate the
ring buffer size.
Fix a bug where CRC errors were reported as framming errors.
Change copyright to a BSD style one.
Added hook for pmap_prefault() and use symbolic constant for new third
argument to vm_page_alloc() (vm_fault.c, various)
Changed the way that upages and page tables are held. (vm_glue.c)
Fixed architectural flaw in allocating pages at interrupt time that was
introduced with the merged cache changes. (vm_page.c, various)
Adjusted some algorithms to acheive better paging performance and to
accomodate the fix for the architectural flaw mentioned above. (vm_pageout.c)
Fixed pbuf handling problem, changed policy on handling read-behind page.
(vnode_pager.c)
Submitted by: John Dyson
implemented the ability to limit bufferspace by memory consumed. (vfs_bio.c)
Fixed recently introduced bugs that caused extra I/O to happen in some
cases. (vfs_cluster.c)
Submitted by: John Dyson
Moved various pmap 'bit' test/set functions back into real functions; gcc
generates better code at the expense of more of it. (pmap.c)
Fixed a deadlock problem with pv entry allocations (pmap.c)
Added a new, optional function 'pmap_prefault' that does clustered page
table preloading (pmap.c)
Changed the way that page tables are held onto (trap.c).
Submitted by: John Dyson
page flipping anytime soon and 4k just wastes memory. Performance via the
looback interface will decrease slightly by this change. Idealy, we need
buffers that can have variable sizes, but this requires a rewrite of far
too much code at the moment.
1) Don't clone routes to multicast destinations; there is nothing useful
to be gained in this case.
2) Reduce default expiration timer to one hour. Busy sites will still
likely want to reduce this, but for ordinary users this is a reasonable
value to use.
delete them when the ``parent'' goes away
route.h: add glue to track this to rtentry structure. WARNING WILL ROBINSON!
This will be yet another incompatible change in your route-using binaries.
I apologize, but this was the only way to do it. I took this opportunity
to increase the size of the metrics to what I believe will be the final
length for 2.1, so that when the T/TCP stuff is done, this won't happen
again.
Print out the length of the compiled sequencer program.
aic7xxx.seq:
More optimizations. Replace generic bcopy routine with bcopy_3
and bcopy_4 (ie unroll the loops) since these are the only two cases used.
Initialize SIMODE1 and SXFRCTL1 from the kernel in ahc_init instead of
at each selection/reselection since this is expensive and only needs to
be done once. Condense function returns into previous instruction if possible.
Reorder some sections to kill superflous jumps. These optimizations kill
the ~150k/s penalty adding support for Twin/Wide cards was costing since
the last place in the commaon path of execution where we had to do ugly,
convoluted testing for the type of card in the sequencer has gone away.
Next stop tagged queuing and target mode.
work (mi_switch() counted the last timeslice again but this didn't affect
the exiting process' rusage because the rusage has already been finalized).
Remove stale comment.
the physical device is closed. Previously only the reverse case was handled.
Abuse the cdevsw interface instead of the vfs interface to do this.
Remove unnecessary #includes.
When using cp to copy a file under the following circumstanes:
- original file in on an NFS filesystem
- destination file is on the same NFS filesystem
- the file is less than 8Mbytes in size
- the file is larger than 65536 bytes in size
the cp process can get frozen in device-wait and never wake up (cp uses
mmap() in this case).
A small change to allocbuf() fixes this.
Obtained from:
bios boot block changed to allow booting from both the attached graphics
display and from a serial port. (A specially compiled serial boot block
is no longer necessary.) The boot block should detect the presence or
absence of a keyboard: if there is no keyboard, COM1 is turned into the
console. This simulates the behavior of the Sun boot PROMs. Unplug your
keyboard, attach a terminal to COM1 and you should be ready to go. :)
Obtained from:
sio.c and sioreg.c changed to allow autodetecting the RB_SERIAL flag
passed by the boot blocks so that the kernel can switch to 'serial
console' mode automagically. 'options COMCONSOLE' can still be specified
to force the kernel to always use the serial port as a console.
CONUNIT and CONADDR can also be specified in the kernel config file
if the user wants to shift the console to a different port.
Obtained from:
Added a new flag (RB_SERIAL) which is passed by the boot block to tell
the kernel that it should use a serial port as a console. (The kernel
can still be forced to boot in serial console mode if 'options COMCONSOLE'
is used.)
Put in the much shorter and cleaner version for the calibrate_cycle_counter
for the Pentium that Bruce suggested. Tested here on my Pentium and
it works okay.
sigreturn() sometimes failed for ordinary returns from signal handlers.
Failures of ordinary returns "can't happen" and are badly handled.
"Temporary" fix: allow users to corrupt PSL_RF. This is fairly
harmless. A correct fix would involve saving the old %eflags (and
perhaps the old segment registers) where the user can't get at them.
(original "High Sierra") CD format. I've already implemented this for
1.1.5.1 (and posted to -hackers), but didn't get any response to it.
Perhaps i'm the only one who has such an old CD lying around...
Everything is done empirically, but i had three of them around (from
different vendors), so there's a high probability that i've got it
right. :)
WDTR, and message reject handlers so they don't need to exist in the
sequencer. All three of these cases are not on the critical path, so it
makes little sense to use up precious sequencer ram for them.
(SCSI control block) instead of having the host PIO it down. Also
reimplement WDTR and SDTR optimization to remove code in the sequencer
and place the responsibility of knowing when to initiate SDTR or WDTR
on the kernel driver. This vastly shortens the sequencer program yet
yeilds the same performance.
properly from the beginning:
1) The `kern_devconf' struct should be a part of the driver's
`softc' structure (now it is).
2) The `description' should say what the device actually is,
rather than just giving a model number (now it does).
3) The device should be registered even if the probe fails, so
that it can be reconfigured later.
4) For netifs, the device state should follow the IFF_UP flag.
Other network interfaces should follow this example. (Please?) Eventually
there should be a rundown routine doing the equivalent of setting IFF_UP
off, and perhaps more if warranted.
attempted to check for insecure and fatal eflags and segment
selectors, but missed many cases and got the IOPL check back to
front. The other syscalls didn't check at all.
sys_process.c, machdep.c:
Only allow PT_WRITE_U to write to the registers (ordinary and FP).
psl.h, locore.s, machdep.c:
Eliminate PSL_MBZ, PSL_MBO and PSL_USERCLR. We are not supposed
to assume anything about the reserved bits. Use PSL_USERCHANGE
and PSL_KERNEL instead. Rename PSL_USERSET to PSL_USER.
exception.s:
Define a private label for use by doreti when returning to user
mode fails.
machdep.c:
In syscalls, allow changing only the eflags that can be changed on
486's in user mode (no longer attempt to allow benign IOPL changes;
allow changing the nasty PSL_NT; don't allow changing the i586
bits).
Don't attempt to check all the cases involving invalid selectors
and %eip's. Just check for privilege violations and let the invalid
things cause a trap.
procfs_machdep.c:
Call the ptrace register functions to do all the work for reading
and writing ordinary registers and for single stepping.
trap.c:
Ignore traps caused by PSL_NT being set. Previously, users could
cause a fatal trap in user mode by setting PSL_NT and executing an
iret, and a fatal trap in kernel mode by setting PSL_NT and making
a syscall. PSL_NT was cleared too late and not in enough modes to
fix the problem.
Make all traps in user mode (except T_NMI) nonfatal.
Recover from traps caused by attempting to load invalid user
registers in doreti by restarting the traps so that they appear to
occur in user mode.
---
Fix bogons that I noticed while fixing the above:
psl.h:
Fix some comments.
Uniformize idempotency ifdef.
exception.s, machdep.c:
Remove rsvd[0-14]. rsvd0 hasn't been reserved since the 486 came
out. Replace rsvd0 by `align'. rsvd[0-11] used wrong (magic
non-unique) trap numbers. Replace rsvd[1-14] by rsvd.
locore.s:
Enable alignment check flag on 486's and 586's.
machdep.c:
Use a better type for kstack[].
Use TFREGP() to find the registers.
Reformat ptrace functions from SEF to something closer to KNF.
procfs_machdep.c:
The wrong pointer to the registers got fixed as a side effect.
Implement reading and writing of FP registers.
/proc/*/*regs now work (only) for processes that are in memory.
Clean up comments.
trap.c, trap.h:
Remove unused trap types.
unreachable case label in kdb_trap().
Use the correct case labels in kdb_trap() so that normal ddb entry doesn't
print a message.
Change all printf's to db_printf's. Now you can put a breakpoint at printf,
and ddb entry messages don't spam the syslog output.
Cosmetic:
Use ISPL() instead of magic numbers.
Don't compile the unused function kdb_kbd_trap().
Improve some asms.
Print the arg to Debugger().
need to be moved into the qcollapse and rcollapse routines, but I don't
have time at the moment to make all the required changes...this will do
for now.
