incarnated, it just matches other deficiencies related to crunchgen
and friends... and we already have similar code in ppp/Makefile.
RELEASE_CRUNCH should be axed, but for now let's be consistent.
Submitted by: Patrick Powell <papowell@astart.com>
track.
The Id line is normally at the bottom of the main comment block in the
man page, separated from the rest of the manpage by an empty comment,
like so;
.\" $Id$
.\"
If the immediately preceding comment is a @(#) format ID marker than the
the $Id$ will line up underneath it with no intervening blank lines.
Otherwise, an additional blank line is inserted.
Approved by: bde
userland code. Using apmd.conf, the apmd(8) configuration file, you
can select the APM events to be handled from userland and specify the
commands for a given event, allowing APM behaviour to be configured
flexibly.
Have Fun!
Submitted by: iwasaki, KOIE Hidetaka <hide@koie.org>
Reviewed by: -hackers, -mobile and bsd-nomads ML folks.
Contributed by: Warner Losh <imp@FreeBSD.org>,
Hiroshi Yamashita <bluemoon@msj.biglobe.ne.jp>,
Yoshihiko SARUMARU <mistral@imasy.or.jp>,
Norihiro Kumagai <kuma@nk.rim.or.jp>,
NAKAGAWA Yoshihisa <nakagawa@jp.FreeBSD.org>, and
Nick Hilliard <nick@foobar.org>.
service. Inetd already uses the process title to indicate that a request
for an internal service is being serviced, so this addition is fairly
orthogonal.
Submitted by: David Malone <dwmalone@maths.tcd.ie>
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
Grammar and Spelling Reviewed by: mpp
While mpp kindly checked grammar and spelling, any technical errors
remaining in the man pages are entirely of mine.
internal services in inetd.conf .
The inetd(8) manpage used to say that the official name of a service
_must_ be used, yet inetd itself was hardcoded to used a service alias for
the auth service, namely ident!
Rather than change inetd.conf and break existing configurations on next
upgrade, we now allow service aliases as well as official names. This
allows the software to work as expected and still support existing
configurations.
This should not breaking existing wrapped configurations either and the
inetd(8) manpage already states that it is the service name specified in
inetd.conf that is used for calls to hosts_access(3).
PR: 11796
Reported by: Alex Charalabidis <alex@wnm.net>
Approved by: des
