NICs. (Finally!) The PCMCIA, ISA and PCI varieties are all supported,
though only the ISA and PCI ones will work on the alpha for now.
PCCARD, ISA and PCI attachments are all provided. Also provided an
ancontrol(8) utility for configuring the NIC, man pages, and updated
pccard.conf.sample. ISA cards are supported in both ISA PnP and hard-wired
mode, although you must configure the kernel explicitly to support the
hardwired mode since you have to know the I/O address and port ahead
of time.
Special thanks to Doug Ambrisko for doing the initial newbus hackery
and getting it to work in infrastructure mode.
USB-EL1202A chipset. Between this and the other two drivers, we should
have support for pretty much every USB ethernet adapter on the market.
The only other USB chip that I know of is the SMC USB97C196, and right
now I don't know of any adapters that use it (including the ones made
by SMC :/ ).
Note that the CATC chip supports a nifty feature: read and write combining.
This allows multiple ethernet packets to be transfered in a single USB
bulk in/out transaction. However I'm again having trouble with large
bulk in transfers like I did with the ADMtek chip, which leads me to
believe that our USB stack needs some work before we can really make
use of this feature. When/if things improve, I intend to revisit the
aue and cue drivers. For now, I've lost enough sanity points.
Kawasaki LSI KL5KUSB101B chip, including the LinkSys USB10T, the
Entrega NET-USB-E45, the Peracom USB Ethernet Adapter, the 3Com
3c19250 and the ADS Technologies USB-10BT. This device is 10mbs
half-duplex only, so there's miibus or ifmedia support. This device
also requires firmware to be loaded into it, however KLSI allows
redistribution of the firmware images (I specifically asked about
this; they said it was ok).
Special thanks to Annelise Anderson for getting me in touch with
KLSI (eventually) and thanks to KLSI for providing the necessary
programming info.
Highlights:
- Add driver files to /sys/dev/usb
- update usbdevs and regenerate attendate files
- update usb_quirks.c
- Update HARDWARE.TXT and RELNOTES.TXT for i386 and alpha
- Update LINT, GENERIC and others for i386, alpha and pc98
- Add man page
- Add module
- Update sysinstall and userconfig.c
USB ethernet chip. Adapters that use this chip include the LinkSys
USB100TX. There are a few others, but I'm not certain of their
availability in the U.S. I used an ADMtek eval board for development.
Note that while the ADMtek chip is a 100Mbps device, you can't really
get 100Mbps speeds over USB. Regardless, this driver uses miibus to
allow speed and duplex mode selection as well as autonegotiation.
Building and kldloading the driver as a module is also supported.
Note that in order to make this driver work, I had to make what some
may consider an ugly hack to sys/dev/usb/usbdi.c. The usbd_transfer()
function will use tsleep() for synchronous transfers that don't complete
right away. This is a problem since there are times when we need to
do sync transfers from an interrupt context (i.e. when reading registers
from the MAC via the control endpoint), where tsleep() us a no-no.
My hack allows the driver to have the code poll for transfer completion
subject to the xfer->timeout timeout rather that calling tsleep().
This hack is controlled by a quirk entry and is only enabled for the
ADMtek device.
Now, I'm sure there are a few of you out there ready to jump on me
and suggest some other approach that doesn't involve a busy wait. The
only solution that might work is to handle the interrupts in a kernel
thread, where you may have something resembling a process context that
makes it okay to tsleep(). This is lovely, except we don't have any
mechanism like that now, and I'm not about to implement such a thing
myself since it's beyond the scope of driver development. (Translation:
I'll be damned if I know how to do it.) If FreeBSD ever aquires such
a mechanism, I'll be glad to revisit the driver to take advantage of
it. In the meantime, I settled for what I perceived to be the solution
that involved the least amount of code changes. In general, the hit
is pretty light.
Also note that my only USB test box has a UHCI controller: I haven't
I don't have a machine with an OHCI controller available.
Highlights:
- Updated usb_quirks.* to add UQ_NO_TSLEEP quirk for ADMtek part.
- Updated usbdevs and regenerated generated files
- Updated HARDWARE.TXT and RELNOTES.TXT files
- Updated sysinstall/device.c and userconfig.c
- Updated kernel configs -- device aue0 is commented out by default
- Updated /sys/conf/files
- Added new kld module directory
now. On one machine with <825a> and <875> controllers, `sym' correctly
attached. On another one with only a <ncr 53c810 fast10 scsi>, the `ncr'
driver correctly attached.
3.3R and then to -current. The pccard support has been left in the
driver, but is presently non-functional because we are using the
isa_compat layer for the moment.
Obtained From: PAO
Sponsored by: Timing Solutions
These drivers were cloned from the ed and ep drivers back in 1994
when PCMCIA cards were a very new thing and we had no other support
for such devices. They treated the PCIC (the chip which controls the
PCCARD slot) as part of their device and generally hacked their way
to success. They have significantly bit-rotted relative to their
ancestor drivers (ed & ep) and they were a dead-end on the evolution
path to proper PCCARD support in FreeBSD.
They have been terminally broken since August 18 where mdodd forgot
them and nobody seems to have missed them enough to fix them since.
I found no outstanding PRs against these drivers.
which it replaces. The new driver supports all of the chips supported
by the ones it replaces, as well as many DEC/Intel 21143 10/100 cards.
This also completes my quest to convert things to miibus and add
Alpha support.
Add MD_ROOT and MD_ROOT_SIZE options to the md driver.
Make the md driver handle MFS_ROOT and MFS_ROOT_SIZE options for compatibility.
Add md driver to GENERIC, PCCARD and LINT.
This is a cleanup which removes the need for some of the worse hacks in
MFS: We really want to have a rootvnode but MFS on a preloaded image
doesn't really have one. md is a true device, so it is less trouble.
This has been tested with make release, and if people remember to add
the "md" pseudo-device to their kernels, PicoBSD should be just fine
as well. If people have no other use for MFS, it can be removed from
the kernel.
for IPv6 yet)
With this patch, you can assigne IPv6 addr automatically, and can reply to
IPv6 ping.
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
to config(8) for static device tables that have not existed for quite
some time. They have been aliases for 'device' for a while, and "tape"
went away entirely as it wasn't used anywhere (except in an example
in LINT.. "fixed").
o Gut the compatibility interface, you now must attach with newbus.
o Unit numbers from pccardd are now ignored. This may change the units
assigned to a card. It now uses the first available unit.
o kill old skeleton code that is now obsolete.
o Use newbus attachment code.
o cleanup interfile dependencies some.
o kill list of devices per slot. we use the device tree for what we need.
o Remove now obsolete code.
o The ep driver (and maybe ed) may need some config file tweaks to
allow it to attach. See config files that were committed for examples
on how to do this.
Drivers to be commited shortly.
This is an interrum fix until the new pccard. ed, ep and sio will be
supported by me with this release, although others are welcome to try
to support other devices before new pccard is working.
I plan on doing minimal further work on this code base. Be careful
when upgrading, since this code is known to work on my laptop and
those of a couple others as well, but your milage may vary.
BUGS TO BE FIXED:
o system memory isn't allocated yet, it will be soon.
o No devices actually have a pccard newbus attach in the tree.
BUGS THAT MIGHT BE FIXED:
o card removal, including suspend, usually hangs the system.
Many thanks to Peter Wemm and Doug Rabson for helping me to fill in
the missing bits of New Bus understanding at FreeBSD Con '99.
revision 1.21
date: 1999/10/15 17:29:20; author: imp; state: Exp; lines: +3 -3
Reorganize the attachement point for pcic (it was unattached and
floating before). Attach pccard devices to pcic, one per slot
(although this may change to one per pcic). pcic is now attached to
isa (to act as a bridge) and pccard is attached to pcic, cbb and
pc98ic (the last two are card bus bridge and the pc98ic version of
pcic, neither of which are in the tree yet). Move pccard compat code
into pccard/pccard_compat.c.
THIS REQUIRES A CONFIG FILE CHANGE. You must change your pcic/card
entries to be:
# PCCARD (PCMCIA) support
controller pcic0 at isa?
controller pcic1 at isa?
controller card0
The old system was upside down and this corrects that problem. It
will make it easier to add support for YENTA pccard/card bus bridges.
Much more cleanup needs to happen before newbus devices can have
pccard attachments. My previous commit's comments were premature.
Forgotten by: imp
In order to make this work, I created a pseudo-PHY driver to deal with
Macronix chips that use the built-in NWAY support and symbol mode port.
This is actually all of them, with the exception of the original MX98713
which presents its NWAY support via the MII serial interface.
The mxphy driver actually manipulates the controller registers directly
rather than using the miibus_readreg()/miibus_writereg() bus interface
since there are no MII registers to read. The mx driver itself pretends
that the NWAY interface is a PHY locayed at MII address 31 for the sole
purpose of allowing the mxphy_probe() routine to know when it needs to
attach to a host controller.
for the AN985 "Centaur" chip, which is apparently the next genetation
of the "Comet." The AN985 is also a tulip clone and is similar to the
AL981 except that it uses a 99C66 EEPROM and a serial MII interface
(instead of direct access to the PHY registers).
Also updated various documentation to mention the AN985 and created
a loadable module.
I don't think there are any cards that use this chip on the market yet:
the datasheet I got from ADMtek has boxes with big X's in them where the
diagrams should be, and the sample boards I got have chips without any
artwork on them.
the Davicom DM9100 and DM9102 chipsets, including the Jaton Corporation
XPressNet. Datasheet is available from www.davicom8.com.
The DM910x chips are still more tulip clones. The API is reproduced
pretty faithfully, unfortunately the performance is pretty bad. The
transmitter seems to have a lot of problems DMAing multi-fragment
packets. The only way to make it work reliably is to coalesce transmitted
packets into a single contiguous buffer. The Linux driver (written by
Davicom) actually does something similar to this. I can't recomment this
NIC as anything more than a "connectivity solution."
This driver uses newbus and miibus and is supported on both i386
and alpha platforms.
SiS 900 and SiS 7016 PCI fast ethernet chipsets. Full manuals for the
SiS chips can be found at www.sis.com.tw.
This is a fairly simple chipset. The receiver uses a 128-bit multicast
hash table and single perfect entry for the station address. Transmit and
receive DMA and FIFO thresholds are easily tuneable. Documentation is
pretty decent and performance is not bad, even on my crufty 486. This
driver uses newbus and miibus and is supported on both the i386 and
alpha architectures.
PCI fast ethernet controller. Currently, the only card I know that uses
this chip is the D-Link DFE-550TX. (Don't ask me where to buy these: the
only cards I have are samples sent to me by D-Link.)
This driver is the first to make use of the miibus code once I'm sure
it all works together nicely, I'll start converting the other drivers.
The Sundance chip is a clone of the 3Com 3c90x Etherlink XL design
only with its own register layout. Support is provided for ifmedia,
hardware multicast filtering, bridging and promiscuous mode.
