The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.
Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix
Calling bus_dmamap_destroy() for a mapping which was allocated with
bus_dmamem_alloc() will result in a panic. This change is not run-time
tested, but I identified the issue while implementing the analogous
method in if_dwc(4), using this implementation as the template.
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
- Add CCM driver and clocks implementations for i.MX 8M
- Add GPC driver for iMX8
- Add clock tree for i.MX 8M Quad
- Add clocks support and new compat strings (where required) for existing i.MX 6 UART, I2C, and GPIO drivers
- Enable aarch64-compatible drivers form i.MX 6 in arm64 GENERIC kernel config
- Add dtb/imx8 kernel module with DTBs for Nitrogen8M and iMX8MQ EVK
With this patch both Nitrogen8M and iMX8MQ EVK boot with NFS root up to multiuser login prompt
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D25274
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
fields in the softc; they're ORed together in the ofw_compat_data.
I already caught myself doing 'sc->fectype == <enum val>' without masking
out the feature bits in one place, and that's sure to happen again.
Glomming them together is convenient for storing them in the ofw_compat_data
array, but there's no reason to keep them together in the softc.
When available, enabling this feature causes the hardware to write data
to the receive buffer starting at a 16-bit offset from the start address.
This eliminates the need to copy the data after receiving to re-align
the protocol headers to a 32-bit boundary.
PR: 222634
Submitted by: sebastian.huber@embedded-brains.de
Newer hardware splits the interrupts onto 3 different irq lines, but the
docs barely mention that there are multiple interrupts, and do not detail
how they're split up. The code now supports 1-3 irqs, and uses the same
interrupt service routine to handle all of them.
I modified the submitted changes to use bus_alloc_resources() instead of
using loops to allocate each irq separately. Thus, blame any bugs on me (I
can't actually test on imx7 hardware).
PR: 222634
Submitted by: sebastian.huber@embedded-brains.de
When the FEC is connected to the AXI bus (indicated by AVB flag), a
MAC reset while a bus transaction is pending can hang the bus.
Instead of resetting, turn off the ENABLE bit, which allows the
hardware to complete any in-progress transfers (appending a bad CRC
to any partial packet) and release the AXI bus. This could probably
be done unconditionally for all hardware variants, but that hasn't
been tested.
PR: 222634
Submitted by: sebastian.huber@embedded-brains.de
This flag is analogous to the Linux driver FEC_QUIRK_HAS_AVB. It
indicates an FEC with support for Audio Video Bridging (AVB). This
indicator is used for various other parts in the Linux driver
(drivers/net/ethernet/freescale/fec_main.c).
Use it to customize the receive/transmit buffer alignment. The receive
buffer alignment increased to 64-bytes on the i.MX 6SoloX and i.MX
7Dual. There are no hard alignment restrictions for transmit buffers on
these chips.
Fix the ffec_softc::fectype type to provide enough storage for the
feature flags.
PR: 222634
Submitted by: sebastian.huber@embedded-brains.de
16 was the correct alignment for older hardware, but the imx7 requires
64-byte alignment, which is a fine value to use on all systems.
PR: 222634
Submitted by: sebastian.huber@embedded-brains.de
After harvesting the hardware statistics counters and summing them into the
interface stats, properly clear the hardware counters back to zero. On imx5
and earlier hardware it is necessary to disable collection of stats while
writing zeroes to all the registers. On imx6 and newer it turns out it's
not even possible to write zeroes, instead you have to toggle a special
"zero everything" control bit in a register.
Count incoming packets with a bad start frame delim as input errors, and
incoming packets dropped due to no fifo space as input drops.
Remove all code related to harvesting the hardware stats less often than
once per second. It turns out the 32-bit stats registers are backed by
16-bit counters under the hood, and they can easily roll over if you only
harvest them once every 3 seconds like the old code was doing. Now we just
read all the regs once a second.
The combination of not properly zeroing the stats registers and 16-bit
counters sometimes wrapping between harvest calls resulted in basically
unusable statistics before these changes.
is no phy-handle property, fall back to using MII_PHY_ANY.
This still doesn't support an mdio bus with multiple PHYs on it, or the
possibility that the PHY being used by this instance of ffec is on the
mdio bus of some other instance (which is now a possibility with imx6ul).
Adding that support will require changes in fdt_get_phyaddr(), which is
currently making some assumptions that don't work with modern fdt data.
This was previously working by accident because BUSDMA_COHERENT_MEMORY has
always been set to strongly-ordered on arm. Now we're moving towards
normal-uncacheable (what might be called write-combining on other platforms)
and using the proper sync ops will be more important. Of course, that
opens the question of just what is the "proper" sync op for shared
concurrent dma access as opposed to accesses where the handoff of control
of the memory has well-defined sequence points that match the available
busdma sync operations.
to check the status property in their probe routines.
Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.
Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.
shifts into the sign bit. Instead use (1U << 31) which gets the
expected result.
This fix is not ideal as it assumes a 32 bit int, but does fix the issue
for most cases.
A similar change was made in OpenBSD.
Discussed with: -arch, rdivacky
Reviewed by: cperciva
Freescale SoCs including the i.MX series. This also works for the newer
SoCs with the ENET gigabit controller, but doesn't use any of the new
hardware features other than enabling gigabit speed.
