Several users with alc(4)-based "Killer" Ethernet cards have reported
issues with this driver not passing traffic, which are solved by
disabling MSI-X using the provided tunable.
To work around this issue, disable MSI-X by default on this card.
This is done by having msix_disable default to 2, which means
"auto-detect". The user can still override this to either 0 or 1 as
desired.
Since these are slow (1Gbps) Ethernet ICs used in low-end systems, it's
unlikely this will cause any practical performance issues; on the other
hand, the card not working by default likely causes issues for many new
FreeBSD users who find their network port doesn't work and have no idea
why.
PR: 230807
MFC after: 1 week
Reviewed by: imp
Pull Request: https://github.com/freebsd/freebsd-src/pull/1185
Apply the following automated changes to try to eliminate
no-longer-needed sys/cdefs.h includes as well as now-empty
blank lines in a row.
Remove /^#if.*\n#endif.*\n#include\s+<sys/cdefs.h>.*\n/
Remove /\n+#include\s+<sys/cdefs.h>.*\n+#if.*\n#endif.*\n+/
Remove /\n+#if.*\n#endif.*\n+/
Remove /^#if.*\n#endif.*\n/
Remove /\n+#include\s+<sys/cdefs.h>\n#include\s+<sys/types.h>/
Remove /\n+#include\s+<sys/cdefs.h>\n#include\s+<sys/param.h>/
Remove /\n+#include\s+<sys/cdefs.h>\n#include\s+<sys/capsicum.h>/
Sponsored by: Netflix
The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.
Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix
With clang 15, the following -Werror warning is produced:
sys/dev/alc/if_alc.c:3441:6: error: variable 'prog' set but not used [-Werror,-Wunused-but-set-variable]
int prog;
^
The 'prog' variable seems to be a left-over from some debugging code
that no longer exists, and can be removed without any functional change.
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D35831
The new Mikrotik 10/25G NIC is mostly compatible with AR8151 hardware,
with few exceptions:
* card supports only 32bit DMA operations
* card does not support write-one-to-clear semantics for interrupt status
register
* MDIO operations can take longer to complete
This patch adds support for Mikrotik 10/25G NIC to the alc driver
while maintaining support for all earlier HW.
The patch was tested with FreeBSD main branch as of commit
f4b38c360e
This was tested on Intel i7-4790K system with Mikrotik 10/25G NIC.
This was tested on Intel i7-4790K system with RB44Ge (AR8151 based 4-port NIC)
to verify backwards compatibility.
PR: 256000
Submitted by: Gatis Peisenieks <gatis@mikrotik.com>
MFC after: 1 week
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
Debugnet is a simplistic and specialized panic- or debug-time reliable
datagram transport. It can drive a single connection at a time and is
currently unidirectional (debug/panic machine transmit to remote server
only).
It is mostly a verbatim code lift from netdump(4). Netdump(4) remains
the only consumer (until the rest of this patch series lands).
The INET-specific logic has been extracted somewhat more thoroughly than
previously in netdump(4), into debugnet_inet.c. UDP-layer logic and up, as
much as possible as is protocol-independent, remains in debugnet.c. The
separation is not perfect and future improvement is welcome. Supporting
INET6 is a long-term goal.
Much of the diff is "gratuitous" renaming from 'netdump_' or 'nd_' to
'debugnet_' or 'dn_' -- sorry. I thought keeping the netdump name on the
generic module would be more confusing than the refactoring.
The only functional change here is the mbuf allocation / tracking. Instead
of initiating solely on netdump-configured interface(s) at dumpon(8)
configuration time, we watch for any debugnet-enabled NIC for link
activation and query it for mbuf parameters at that time. If they exceed
the existing high-water mark allocation, we re-allocate and track the new
high-water mark. Otherwise, we leave the pre-panic mbuf allocation alone.
In a future patch in this series, this will allow initiating netdump from
panic ddb(4) without pre-panic configuration.
No other functional change intended.
Reviewed by: markj (earlier version)
Some discussion with: emaste, jhb
Objection from: marius
Differential Revision: https://reviews.freebsd.org/D21421
Remove unused and easy to misuse PNP macro parameter
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Approved by: re (glen)
I was not aware Warner was making or planning to make forward progress in
this area and have since been informed of that.
It's easy to apply/reapply when churn dies down.
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
It seems Killer E2200/E2400 has a BIOS misconfiguration or silicon
bug which triggers DMA write errors when driver uses advertised
maximum payload size. Force the maximum payload size to 128 bytes
in DMA configuration.
This change should fix occasional DMA write errors reported on
Killer E2200.
Tested by: <psy0nic@sys-tek.org>
controllers. For Gigabit Ethernet version of AR816x, AR813x/AR815x
except L1D controller, use vendor recommended ASPM parameters.
While here, increase alc_dma_burst array size. Broken H/W can
return bogus value in theory.
These controllers seem to have the same feature of AR813x/AR815x and
improved RSS support(4 TX queues and 8 RX queues). alc(4) supports
all hardware features except RSS. I didn't implement RX checksum
offloading for AR816x/AR817x just because I couldn't get
confirmation from the Vendor whether AR816x/AR817x corrected its
predecessor's RX checksum offloading bug on fragmented packets.
This change adds supports for the following controllers.
o AR8161 PCIe Gigabit Ethernet controller
o AR8162 PCIe Fast Ethernet controller
o AR8171 PCIe Gigabit Ethernet controller
o AR8172 PCIe Fast Ethernet controller
o Killer E2200 Gigabit Ethernet controller
Tested by: Many
Relnotes: yes
MFC after: 2 weeks
HW donated by: Qualcomm Atheros Communications, Inc.
In particular, don't check the value of the bus_dma map against NULL
to determine if either bus_dmamem_alloc() or bus_dmamap_load() succeeded.
Instead, assume that bus_dmamap_load() succeeeded (and thus that
bus_dmamap_unload() should be called) if the bus address for a resource
is non-zero, and assume that bus_dmamem_alloc() succeeded (and thus
that bus_dmamem_free() should be called) if the virtual address for a
resource is not NULL.
In many cases these bugs could result in leaks when a driver was detached.
Reviewed by: yongari
MFC after: 2 weeks
out 32 is not enough to support a full sized TSO packet.
While I'm here fix a long standing bug introduced in r169632 in
bce(4) where it didn't include L2 header length of TSO packet in
the maximum DMA segment size calculation.
In collaboration with: rmacklem
MFC after: 2 weeks
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
#defines. This also has the advantage that it makes the names more
compact, iand also allows us to correct the non-uniform naming of
the PCIM_LINK_* defines, making them all consistent amongst themselves.
This is a mostly mechanical rename:
s/PCIR_EXPRESS_/PCIER_/g
s/PCIM_EXP_/PCIEM_/g
s/PCIM_LINK_/PCIEM_LINK_/g
When this is MFC'd, #defines will be added for the old names to assist
out-of-tree drivers.
Discussed with: jhb
MFC after: 1 week
Because driver is accessing a common MII structure in
mii_pollstat(), updating user supplied structure should be done
before dropping a driver lock.
Reported by: Karim (fodillemlinkarimi <> gmail dot com)
programming secret. The PHY would go into sleep state when it
detects no established link and it will re-establish link when the
cable is plugged in. Previously it failed to re-establish link
when the cable is plugged in such that it required to manually down
and up the interface again to make it work. This came from
incorrectly programmed hibernation parameters. According to
Atheros, each PHY chip requires different configuration for
hibernation and different vendor has different settings for the
same chip.
Disabling hibernation may consume more power but establishing link
looks more important than saving power.
Special thanks to Atheros for giving me instructions that disable
hibernation.
MFC after: 1 week
Approved by: re (kib)
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
apply AR8152 v1.0 specific initialization code. Fix this bug by
explicitly reading PCI device revision id via PCI accessor.
Reported by: Gabriel Linder ( linder.gabriel <> gmail dot com )
value. While I'm here enable all clocks before initializing
controller. This change should fix lockup issue seen on AR8152
v1.1 PCIe Fast Ethernet controller.
PR: kern/154076
MFC after: 3 days
