- Unconditionally call *_stop() if device is in the tree. This is to
prevent callouts from happening after the device is gone. Checks for
bus_child_present() should be added in the future to keep from touching
potentially non-existent hardware in *_detach(). Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
that ifmedia_removeall() can be unconditionally called on detach. There
is no way to detect whether ifmedia has been initialized without using
a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
properly (likely due to mbuf exhaustion.) Previously, the driver
got somewhat wedged.
Also, remove the annoying messages printed every time xl_encap
couldn't allocate a mbuf; they served no useful purpose, and just made
an mbuf exhaustion situation more annoying.
MFC after: 1 week
RX part of this driver too. It's better since the code wasn't
dealing with bus_dmamap_load() returning EINPROGRESS, and this
can't happen with bus_dmamap_load_mbuf().
Submitted by: jake
- Remove locking of the softc in the attach method, instead depending on
bus_setup_intr being at the end of attach (delaying interrupt enable until
after ether_ifattach is called)
- Call *_detach directly in the error case of attach, depending on checking
in detach to only free resources that were allocated. This puts all
resource freeing in one place, avoiding thinkos that lead to memory leaks.
- Add bus_child_present check to calls to *_stop in the detach method to
be sure hw is present before touching its registers.
- Remove bzero softc calls since device_t should do this for us.
- dc: move interrupt allocation back where it was before. It was unnecessary
to move it. This reverts part of 1.88
- rl: move irq allocation before ether_ifattach. Problems might have been
caused by allocating the irq after enabling interrupts on the card.
- rl: call rl_stop before ether_ifdetach
- sf: call sf_stop before ether_ifdetach
- sis: add missed free of sis_tag
- sis: check errors from tag creation
- sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- sk: remove duplicate initialization of sk_dev
- ste: add missed bus_generic_detach
- ti: call ti_stop before ether_ifdetach
- ti: add missed error setting in ti_rdata alloc failure
- vr: add missed error setting in I/O, memory mapping cases
- xl: add missed error setting in I/O, memory mapping cases
- xl: remove multi-level goto on attach failure
- xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- Calls to free(9) are unconditional because it is valid to call free with a
null pointer.
Reviewed by: imp, mdodd
code messed up on B & C chipsets because it lost the packet header
and therefore the flag indicating the need for hardware checksums.
MFC after: 2 weeks
driver should use port or memory based IO, determine it dynamically
at runtime, preferring MMIO where possible. This helps us support newer
arches which dislike port based access better.
Tested on i386 & sparc64, with 3c900, 905, 905b, and 905C cards.
(in varying combinations by both jake and myself)
as opposed to one after the other. This is faster in both -CURRENT
and -STABLE. Additionally, there is less code duplication for
error-checking.
One thing to note is that this code seems to return(1) when no buffers
are available; perhaps ENOBUFS should be the correct return value?
Partially submitted & tested by: Hiten Pandya <hiten@unixdaemons.com>
MFC after: 1 week
wish the busdma APIs were more consistent accross architectures.
We should probably move all the other DMA map creations in
xl_attach() where we can really handle them failing, since
xl_init() is void and shouldn't fail.
Pointy hat to: mux
Tested by: Anders Andersson <anders@hack.org>
bus_dmamap_load() it.
- Make it so reusing mbufs when we can't allocate (or map) new ones
actually works. We were previously trying to reuse a mbuf which
was already bus_dmamap_unload()'ed.
Reviewed by: silby
- Add conversions to/from little endian for fields that the NIC accesses
by DMA as required.
- Add some bus_dmamap_sync() calls, and correct some existing ones.
- Read the receiver information from the EEPROM in an endian-neutral
manner.
- Load all RX and TX descriptors in a single DMA map up front, and
get the bus addresses of individual descriptors by address arithmetic;
this fixes multiple use of the descriptor tags, which would have
undesired effects.
It seems that xl still does not work on e250 boxen, for reasons which
are not clear yet.
Reviewed by: mux
is read one clock edge too late. This bit is driven low by
slave (as any other input data bits from slave) when the clock
is LOW. The current code did read the bit after the clock was
driven high again.
Reviewed by: luoqi
MFC after: 2 weeks
bus_dmamap_load_mbuf() returned EFBIG.
o Fix mbuf leaks in an error (rare) code path.
o Reuse the TX descriptor if xl_encap() failed instead of
just picking the next one.
o Better error messages.
it possible to use this driver under ia64, sparc64 (though
there may be endianness issues with this one) and other archs.
Tested on: i386, alpha (gallatin)
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes
Reviewed by: many
Approved by: re
According to the MII specification, the delay produced by our
reads alone are sufficient for correct operation.
This reduces the time mii_tick takes from 10ms to ~1ms here. That's
still a lot, but much better than before.
Submitted by: Harti Brandt <brandt@fokus.gmd.de>
MFC after: 3 weeks
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
a major slowdown, and re-enable stats overflow interrupts.
For future reference, the bug was in our code, and not
some bug in the 3com chips.
Reviewed by: wpaul
MFC after: 2 days
dual function card. It needs pretty much the same flags as the 656C,
except that it seems to need both the INVERT_MII_PWR and INVERT_LED_PWR
flags set. Tested with cardbus in -current as of today.
Also added support for the 3c656, which looks to be the same as
the 656B, except it doesn't need the EEPROM_8BIT flag. I think. This
one is untested, but the added support should not break any of the
other cards.
never completed" message. The RX reset takes longer complete than it
used to, a lot longer in fact than xl_wait() is prepared to wait.
When we do the RX reset in xl_reset(), this cases xl_wait() to time out
and whine. We wait a little extra time now after the RX reset, which
should silence the warning.
Thanks to obrien for finally getting me a box with a NIC that
causes this problem for me to tinker with.
setting the 'max packet size' register in window 3. This only
works for cards based on the cyclone or newer chipsets (i.e. it
won't work with the original 3c905/boomerang cards).
There is a trick which will work with the boomerang, which is to turn
on the 'large packets ok' bit in the MAC control register, however this
lets the chip accept any frame up to 4K in length, which is larger than
the mbuf cluster buffers we use to receive frames. If somebody sends us
such a frame and the chip DMAs it to us, it could write past the end
of the cluster buffer and clobber something.
PR: kern/27742
