freebsd-src/sys/cam/scsi/scsi_all.h

1614 lines
40 KiB
C
Raw Normal View History

/*-
* Largely written by Julian Elischer (julian@tfs.com)
* for TRW Financial Systems.
*
* TRW Financial Systems, in accordance with their agreement with Carnegie
* Mellon University, makes this software available to CMU to distribute
* or use in any manner that they see fit as long as this message is kept with
* the software. For this reason TFS also grants any other persons or
* organisations permission to use or modify this software.
*
* TFS supplies this software to be publicly redistributed
* on the understanding that TFS is not responsible for the correct
* functioning of this software in any circumstances.
*
* Ported to run under 386BSD by Julian Elischer (julian@tfs.com) Sept 1992
*
1999-08-28 01:08:13 +00:00
* $FreeBSD$
*/
/*
* SCSI general interface description
*/
#ifndef _SCSI_SCSI_ALL_H
#define _SCSI_SCSI_ALL_H 1
#include <sys/cdefs.h>
#ifdef _KERNEL
/*
* This is the number of seconds we wait for devices to settle after a SCSI
* bus reset.
*/
extern int scsi_delay;
#endif /* _KERNEL */
/*
* SCSI command format
*/
/*
* Define dome bits that are in ALL (or a lot of) scsi commands
*/
#define SCSI_CTL_LINK 0x01
#define SCSI_CTL_FLAG 0x02
#define SCSI_CTL_VENDOR 0xC0
#define SCSI_CMD_LUN 0xA0 /* these two should not be needed */
#define SCSI_CMD_LUN_SHIFT 5 /* LUN in the cmd is no longer SCSI */
#define SCSI_MAX_CDBLEN 16 /*
* 16 byte commands are in the
* SCSI-3 spec
*/
#if defined(CAM_MAX_CDBLEN) && (CAM_MAX_CDBLEN < SCSI_MAX_CDBLEN)
#error "CAM_MAX_CDBLEN cannot be less than SCSI_MAX_CDBLEN"
#endif
/* 6byte CDBs special case 0 length to be 256 */
#define SCSI_CDB6_LEN(len) ((len) == 0 ? 256 : len)
/*
* This type defines actions to be taken when a particular sense code is
* received. Right now, these flags are only defined to take up 16 bits,
* but can be expanded in the future if necessary.
*/
typedef enum {
SS_NOP = 0x000000, /* Do nothing */
SS_RETRY = 0x010000, /* Retry the command */
SS_FAIL = 0x020000, /* Bail out */
SS_START = 0x030000, /* Send a Start Unit command to the device,
* then retry the original command.
*/
SS_TUR = 0x040000, /* Send a Test Unit Ready command to the
* device, then retry the original command.
*/
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
SS_REQSENSE = 0x050000, /* Send a RequestSense command to the
* device, then retry the original command.
*/
SS_MASK = 0xff0000
} scsi_sense_action;
typedef enum {
SSQ_NONE = 0x0000,
SSQ_DECREMENT_COUNT = 0x0100, /* Decrement the retry count */
SSQ_MANY = 0x0200, /* send lots of recovery commands */
SSQ_RANGE = 0x0400, /*
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
* This table entry represents the
* end of a range of ASCQs that
* have identical error actions
* and text.
*/
SSQ_PRINT_SENSE = 0x0800,
SSQ_MASK = 0xff00
} scsi_sense_action_qualifier;
/* Mask for error status values */
#define SS_ERRMASK 0xff
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
/* The default, retyable, error action */
#define SS_RDEF SS_RETRY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE|EIO
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
/* The retyable, error action, with table specified error code */
#define SS_RET SS_RETRY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
/* Fatal error action, with table specified error code */
#define SS_FATAL SS_FAIL|SSQ_PRINT_SENSE
struct scsi_generic
{
u_int8_t opcode;
u_int8_t bytes[11];
};
struct scsi_request_sense
{
u_int8_t opcode;
u_int8_t byte2;
u_int8_t unused[2];
u_int8_t length;
u_int8_t control;
};
struct scsi_test_unit_ready
{
u_int8_t opcode;
u_int8_t byte2;
u_int8_t unused[3];
u_int8_t control;
};
struct scsi_send_diag
{
u_int8_t opcode;
u_int8_t byte2;
#define SSD_UOL 0x01
#define SSD_DOL 0x02
#define SSD_SELFTEST 0x04
#define SSD_PF 0x10
u_int8_t unused[1];
u_int8_t paramlen[2];
u_int8_t control;
};
struct scsi_sense
{
u_int8_t opcode;
u_int8_t byte2;
u_int8_t unused[2];
u_int8_t length;
u_int8_t control;
};
struct scsi_inquiry
{
u_int8_t opcode;
u_int8_t byte2;
#define SI_EVPD 0x01
u_int8_t page_code;
u_int8_t reserved;
u_int8_t length;
u_int8_t control;
};
struct scsi_mode_sense_6
{
u_int8_t opcode;
u_int8_t byte2;
#define SMS_DBD 0x08
u_int8_t page;
#define SMS_PAGE_CODE 0x3F
#define SMS_VENDOR_SPECIFIC_PAGE 0x00
#define SMS_DISCONNECT_RECONNECT_PAGE 0x02
#define SMS_FORMAT_DEVICE_PAGE 0x03
#define SMS_GEOMETRY_PAGE 0x04
#define SMS_CACHE_PAGE 0x08
#define SMS_PERIPHERAL_DEVICE_PAGE 0x09
#define SMS_CONTROL_MODE_PAGE 0x0A
#define SMS_PROTO_SPECIFIC_PAGE 0x19
#define SMS_INFO_EXCEPTIONS_PAGE 0x1C
#define SMS_ALL_PAGES_PAGE 0x3F
#define SMS_PAGE_CTRL_MASK 0xC0
#define SMS_PAGE_CTRL_CURRENT 0x00
#define SMS_PAGE_CTRL_CHANGEABLE 0x40
#define SMS_PAGE_CTRL_DEFAULT 0x80
#define SMS_PAGE_CTRL_SAVED 0xC0
u_int8_t unused;
u_int8_t length;
u_int8_t control;
};
struct scsi_mode_sense_10
{
u_int8_t opcode;
u_int8_t byte2; /* same bits as small version */
u_int8_t page; /* same bits as small version */
u_int8_t unused[4];
u_int8_t length[2];
u_int8_t control;
};
struct scsi_mode_select_6
{
u_int8_t opcode;
u_int8_t byte2;
#define SMS_SP 0x01
#define SMS_PF 0x10
u_int8_t unused[2];
u_int8_t length;
u_int8_t control;
};
struct scsi_mode_select_10
{
u_int8_t opcode;
u_int8_t byte2; /* same bits as small version */
u_int8_t unused[5];
u_int8_t length[2];
u_int8_t control;
};
/*
* When sending a mode select to a tape drive, the medium type must be 0.
*/
struct scsi_mode_hdr_6
{
u_int8_t datalen;
u_int8_t medium_type;
u_int8_t dev_specific;
u_int8_t block_descr_len;
};
struct scsi_mode_hdr_10
{
u_int8_t datalen[2];
u_int8_t medium_type;
u_int8_t dev_specific;
u_int8_t reserved[2];
u_int8_t block_descr_len[2];
};
struct scsi_mode_block_descr
{
u_int8_t density_code;
u_int8_t num_blocks[3];
u_int8_t reserved;
u_int8_t block_len[3];
};
struct scsi_log_sense
{
u_int8_t opcode;
u_int8_t byte2;
#define SLS_SP 0x01
#define SLS_PPC 0x02
u_int8_t page;
#define SLS_PAGE_CODE 0x3F
#define SLS_ALL_PAGES_PAGE 0x00
#define SLS_OVERRUN_PAGE 0x01
#define SLS_ERROR_WRITE_PAGE 0x02
#define SLS_ERROR_READ_PAGE 0x03
#define SLS_ERROR_READREVERSE_PAGE 0x04
#define SLS_ERROR_VERIFY_PAGE 0x05
#define SLS_ERROR_NONMEDIUM_PAGE 0x06
#define SLS_ERROR_LASTN_PAGE 0x07
#define SLS_SELF_TEST_PAGE 0x10
#define SLS_IE_PAGE 0x2f
#define SLS_PAGE_CTRL_MASK 0xC0
#define SLS_PAGE_CTRL_THRESHOLD 0x00
#define SLS_PAGE_CTRL_CUMULATIVE 0x40
#define SLS_PAGE_CTRL_THRESH_DEFAULT 0x80
#define SLS_PAGE_CTRL_CUMUL_DEFAULT 0xC0
u_int8_t reserved[2];
u_int8_t paramptr[2];
u_int8_t length[2];
u_int8_t control;
};
struct scsi_log_select
{
u_int8_t opcode;
u_int8_t byte2;
/* SLS_SP 0x01 */
#define SLS_PCR 0x02
u_int8_t page;
/* SLS_PAGE_CTRL_MASK 0xC0 */
/* SLS_PAGE_CTRL_THRESHOLD 0x00 */
/* SLS_PAGE_CTRL_CUMULATIVE 0x40 */
/* SLS_PAGE_CTRL_THRESH_DEFAULT 0x80 */
/* SLS_PAGE_CTRL_CUMUL_DEFAULT 0xC0 */
u_int8_t reserved[4];
u_int8_t length[2];
u_int8_t control;
};
struct scsi_log_header
{
u_int8_t page;
u_int8_t reserved;
u_int8_t datalen[2];
};
struct scsi_log_param_header {
u_int8_t param_code[2];
u_int8_t param_control;
#define SLP_LP 0x01
#define SLP_LBIN 0x02
#define SLP_TMC_MASK 0x0C
#define SLP_TMC_ALWAYS 0x00
#define SLP_TMC_EQUAL 0x04
#define SLP_TMC_NOTEQUAL 0x08
#define SLP_TMC_GREATER 0x0C
#define SLP_ETC 0x10
#define SLP_TSD 0x20
#define SLP_DS 0x40
#define SLP_DU 0x80
u_int8_t param_len;
};
struct scsi_control_page {
u_int8_t page_code;
u_int8_t page_length;
u_int8_t rlec;
#define SCB_RLEC 0x01 /*Report Log Exception Cond*/
u_int8_t queue_flags;
#define SCP_QUEUE_ALG_MASK 0xF0
#define SCP_QUEUE_ALG_RESTRICTED 0x00
#define SCP_QUEUE_ALG_UNRESTRICTED 0x10
#define SCP_QUEUE_ERR 0x02 /*Queued I/O aborted for CACs*/
#define SCP_QUEUE_DQUE 0x01 /*Queued I/O disabled*/
u_int8_t eca_and_aen;
#define SCP_EECA 0x80 /*Enable Extended CA*/
#define SCP_RAENP 0x04 /*Ready AEN Permission*/
#define SCP_UAAENP 0x02 /*UA AEN Permission*/
#define SCP_EAENP 0x01 /*Error AEN Permission*/
u_int8_t reserved;
u_int8_t aen_holdoff_period[2];
};
struct scsi_cache_page {
u_int8_t page_code;
#define SCHP_PAGE_SAVABLE 0x80 /* Page is savable */
u_int8_t page_length;
u_int8_t cache_flags;
#define SCHP_FLAGS_WCE 0x04 /* Write Cache Enable */
#define SCHP_FLAGS_MF 0x02 /* Multiplication factor */
#define SCHP_FLAGS_RCD 0x01 /* Read Cache Disable */
u_int8_t rw_cache_policy;
u_int8_t dis_prefetch[2];
u_int8_t min_prefetch[2];
u_int8_t max_prefetch[2];
u_int8_t max_prefetch_ceil[2];
};
struct scsi_info_exceptions_page {
u_int8_t page_code;
#define SIEP_PAGE_SAVABLE 0x80 /* Page is savable */
u_int8_t page_length;
u_int8_t info_flags;
#define SIEP_FLAGS_PERF 0x80
#define SIEP_FLAGS_EBF 0x20
#define SIEP_FLAGS_EWASC 0x10
#define SIEP_FLAGS_DEXCPT 0x08
#define SIEP_FLAGS_TEST 0x04
#define SIEP_FLAGS_EBACKERR 0x02
#define SIEP_FLAGS_LOGERR 0x01
u_int8_t mrie;
u_int8_t interval_timer[4];
u_int8_t report_count[4];
};
struct scsi_proto_specific_page {
u_int8_t page_code;
#define SPSP_PAGE_SAVABLE 0x80 /* Page is savable */
u_int8_t page_length;
u_int8_t protocol;
#define SPSP_PROTO_FC 0x00
#define SPSP_PROTO_SPI 0x01
#define SPSP_PROTO_SSA 0x02
#define SPSP_PROTO_1394 0x03
#define SPSP_PROTO_RDMA 0x04
#define SPSP_PROTO_ISCSI 0x05
#define SPSP_PROTO_SAS 0x06
#define SPSP_PROTO_ADT 0x07
#define SPSP_PROTO_ATA 0x08
#define SPSP_PROTO_NONE 0x0f
};
struct scsi_reserve
{
u_int8_t opcode;
u_int8_t byte2;
u_int8_t unused[2];
u_int8_t length;
u_int8_t control;
};
struct scsi_release
{
u_int8_t opcode;
u_int8_t byte2;
u_int8_t unused[2];
u_int8_t length;
u_int8_t control;
};
struct scsi_prevent
{
u_int8_t opcode;
u_int8_t byte2;
u_int8_t unused[2];
u_int8_t how;
u_int8_t control;
};
#define PR_PREVENT 0x01
#define PR_ALLOW 0x00
struct scsi_sync_cache
{
u_int8_t opcode;
u_int8_t byte2;
u_int8_t begin_lba[4];
u_int8_t reserved;
u_int8_t lb_count[2];
u_int8_t control;
};
struct scsi_changedef
{
u_int8_t opcode;
u_int8_t byte2;
u_int8_t unused1;
u_int8_t how;
u_int8_t unused[4];
u_int8_t datalen;
u_int8_t control;
};
struct scsi_read_buffer
{
u_int8_t opcode;
u_int8_t byte2;
#define RWB_MODE 0x07
#define RWB_MODE_HDR_DATA 0x00
#define RWB_MODE_DATA 0x02
#define RWB_MODE_DOWNLOAD 0x04
#define RWB_MODE_DOWNLOAD_SAVE 0x05
u_int8_t buffer_id;
u_int8_t offset[3];
u_int8_t length[3];
u_int8_t control;
};
struct scsi_write_buffer
{
u_int8_t opcode;
u_int8_t byte2;
u_int8_t buffer_id;
u_int8_t offset[3];
u_int8_t length[3];
u_int8_t control;
};
struct scsi_rw_6
{
u_int8_t opcode;
u_int8_t addr[3];
/* only 5 bits are valid in the MSB address byte */
#define SRW_TOPADDR 0x1F
u_int8_t length;
u_int8_t control;
};
struct scsi_rw_10
{
u_int8_t opcode;
#define SRW10_RELADDR 0x01
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
/* EBP defined for WRITE(10) only */
#define SRW10_EBP 0x04
#define SRW10_FUA 0x08
#define SRW10_DPO 0x10
u_int8_t byte2;
u_int8_t addr[4];
u_int8_t reserved;
u_int8_t length[2];
u_int8_t control;
};
struct scsi_rw_12
{
u_int8_t opcode;
#define SRW12_RELADDR 0x01
#define SRW12_FUA 0x08
#define SRW12_DPO 0x10
u_int8_t byte2;
u_int8_t addr[4];
u_int8_t length[4];
u_int8_t reserved;
u_int8_t control;
};
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
struct scsi_rw_16
{
u_int8_t opcode;
#define SRW16_RELADDR 0x01
#define SRW16_FUA 0x08
#define SRW16_DPO 0x10
u_int8_t byte2;
u_int8_t addr[8];
u_int8_t length[4];
u_int8_t reserved;
u_int8_t control;
};
struct scsi_start_stop_unit
{
u_int8_t opcode;
u_int8_t byte2;
#define SSS_IMMED 0x01
u_int8_t reserved[2];
u_int8_t how;
#define SSS_START 0x01
#define SSS_LOEJ 0x02
u_int8_t control;
};
struct ata_pass_12 {
u_int8_t opcode;
u_int8_t protocol;
#define AP_MULTI 0xe0
u_int8_t flags;
#define AP_T_LEN 0x03
#define AP_BB 0x04
#define AP_T_DIR 0x08
#define AP_CK_COND 0x20
#define AP_OFFLINE 0x60
u_int8_t features;
u_int8_t sector_count;
u_int8_t lba_low;
u_int8_t lba_mid;
u_int8_t lba_high;
u_int8_t device;
u_int8_t command;
u_int8_t reserved;
u_int8_t control;
};
struct ata_pass_16 {
u_int8_t opcode;
u_int8_t protocol;
#define AP_EXTEND 0x01
u_int8_t flags;
u_int8_t features_ext;
u_int8_t features;
u_int8_t sector_count_ext;
u_int8_t sector_count;
u_int8_t lba_low_ext;
u_int8_t lba_low;
u_int8_t lba_mid_ext;
u_int8_t lba_mid;
u_int8_t lba_high_ext;
u_int8_t lba_high;
u_int8_t device;
u_int8_t command;
u_int8_t control;
};
#define SC_SCSI_1 0x01
#define SC_SCSI_2 0x03
/*
* Opcodes
*/
#define TEST_UNIT_READY 0x00
#define REQUEST_SENSE 0x03
#define READ_6 0x08
#define WRITE_6 0x0A
#define INQUIRY 0x12
#define MODE_SELECT_6 0x15
#define MODE_SENSE_6 0x1A
#define START_STOP_UNIT 0x1B
#define START_STOP 0x1B
#define RESERVE 0x16
#define RELEASE 0x17
#define RECEIVE_DIAGNOSTIC 0x1C
#define SEND_DIAGNOSTIC 0x1D
#define PREVENT_ALLOW 0x1E
#define READ_CAPACITY 0x25
#define READ_10 0x28
#define WRITE_10 0x2A
#define POSITION_TO_ELEMENT 0x2B
#define SYNCHRONIZE_CACHE 0x35
#define READ_DEFECT_DATA_10 0x37
#define WRITE_BUFFER 0x3B
#define READ_BUFFER 0x3C
#define CHANGE_DEFINITION 0x40
#define LOG_SELECT 0x4C
#define LOG_SENSE 0x4D
#define MODE_SELECT_10 0x55
#define MODE_SENSE_10 0x5A
#define ATA_PASS_16 0x85
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
#define READ_16 0x88
#define WRITE_16 0x8A
#define SERVICE_ACTION_IN 0x9E
2002-06-04 17:41:47 +00:00
#define REPORT_LUNS 0xA0
#define ATA_PASS_12 0xA1
#define MAINTENANCE_IN 0xA3
#define MAINTENANCE_OUT 0xA4
#define MOVE_MEDIUM 0xA5
#define READ_12 0xA8
#define WRITE_12 0xAA
#define READ_ELEMENT_STATUS 0xB8
/* Maintenance In Service Action Codes */
#define REPORT_IDENTIFYING_INFRMATION 0x05
#define REPORT_TARGET_PORT_GROUPS 0x0A
#define REPORT_ALIASES 0x0B
#define REPORT_SUPPORTED_OPERATION_CODES 0x0C
#define REPORT_SUPPORTED_TASK_MANAGEMENT_FUNCTIONS 0x0D
#define REPORT_PRIORITY 0x0E
#define REPORT_TIMESTAMP 0x0F
#define MANAGEMENT_PROTOCOL_IN 0x10
/* Maintenance Out Service Action Codes */
#define SET_IDENTIFY_INFORMATION 0x06
#define SET_TARGET_PORT_GROUPS 0x0A
#define CHANGE_ALIASES 0x0B
#define SET_PRIORITY 0x0E
#define SET_TIMESTAMP 0x0F
#define MANGAEMENT_PROTOCOL_OUT 0x10
/*
* Device Types
*/
#define T_DIRECT 0x00
#define T_SEQUENTIAL 0x01
#define T_PRINTER 0x02
#define T_PROCESSOR 0x03
#define T_WORM 0x04
#define T_CDROM 0x05
#define T_SCANNER 0x06
#define T_OPTICAL 0x07
#define T_CHANGER 0x08
#define T_COMM 0x09
#define T_ASC0 0x0a
#define T_ASC1 0x0b
#define T_STORARRAY 0x0c
#define T_ENCLOSURE 0x0d
#define T_RBC 0x0e
#define T_OCRW 0x0f
#define T_OSD 0x11
#define T_ADC 0x12
#define T_NODEVICE 0x1f
#define T_ANY 0xff /* Used in Quirk table matches */
#define T_REMOV 1
#define T_FIXED 0
/*
* This length is the initial inquiry length used by the probe code, as
* well as the legnth necessary for scsi_print_inquiry() to function
* correctly. If either use requires a different length in the future,
* the two values should be de-coupled.
*/
#define SHORT_INQUIRY_LENGTH 36
struct scsi_inquiry_data
{
u_int8_t device;
#define SID_TYPE(inq_data) ((inq_data)->device & 0x1f)
#define SID_QUAL(inq_data) (((inq_data)->device & 0xE0) >> 5)
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
#define SID_QUAL_LU_CONNECTED 0x00 /*
* The specified peripheral device
* type is currently connected to
* logical unit. If the target cannot
* determine whether or not a physical
* device is currently connected, it
* shall also use this peripheral
* qualifier when returning the INQUIRY
* data. This peripheral qualifier
* does not mean that the device is
* ready for access by the initiator.
*/
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
#define SID_QUAL_LU_OFFLINE 0x01 /*
* The target is capable of supporting
* the specified peripheral device type
* on this logical unit; however, the
* physical device is not currently
* connected to this logical unit.
*/
#define SID_QUAL_RSVD 0x02
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
#define SID_QUAL_BAD_LU 0x03 /*
* The target is not capable of
* supporting a physical device on
* this logical unit. For this
* peripheral qualifier the peripheral
* device type shall be set to 1Fh to
* provide compatibility with previous
* versions of SCSI. All other
* peripheral device type values are
* reserved for this peripheral
* qualifier.
*/
#define SID_QUAL_IS_VENDOR_UNIQUE(inq_data) ((SID_QUAL(inq_data) & 0x08) != 0)
u_int8_t dev_qual2;
#define SID_QUAL2 0x7F
#define SID_IS_REMOVABLE(inq_data) (((inq_data)->dev_qual2 & 0x80) != 0)
u_int8_t version;
#define SID_ANSI_REV(inq_data) ((inq_data)->version & 0x07)
#define SCSI_REV_0 0
#define SCSI_REV_CCS 1
#define SCSI_REV_2 2
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
#define SCSI_REV_SPC 3
#define SCSI_REV_SPC2 4
#define SCSI_REV_SPC3 5
#define SCSI_REV_SPC4 6
#define SID_ECMA 0x38
#define SID_ISO 0xC0
u_int8_t response_format;
#define SID_AENC 0x80
#define SID_TrmIOP 0x40
u_int8_t additional_length;
#define SID_ADDITIONAL_LENGTH(iqd) \
((iqd)->additional_length + \
offsetof(struct scsi_inquiry_data, additional_length) + 1)
u_int8_t spc3_flags;
#define SPC3_SID_PROTECT 0x01
#define SPC3_SID_3PC 0x08
#define SPC3_SID_TPGS_MASK 0x30
#define SPC3_SID_TPGS_IMPLICIT 0x10
#define SPC3_SID_TPGS_EXPLICIT 0x20
#define SPC3_SID_ACC 0x40
#define SPC3_SID_SCCS 0x80
u_int8_t spc2_flags;
#define SPC2_SID_MChngr 0x08
#define SPC2_SID_MultiP 0x10
#define SPC2_SID_EncServ 0x40
#define SPC2_SID_BQueue 0x80
#define INQ_DATA_TQ_ENABLED(iqd) \
((SID_ANSI_REV(iqd) < SCSI_REV_SPC2)? ((iqd)->flags & SID_CmdQue) : \
(((iqd)->flags & SID_CmdQue) && !((iqd)->spc2_flags & SPC2_SID_BQueue)) || \
(!((iqd)->flags & SID_CmdQue) && ((iqd)->spc2_flags & SPC2_SID_BQueue)))
u_int8_t flags;
#define SID_SftRe 0x01
#define SID_CmdQue 0x02
#define SID_Linked 0x08
#define SID_Sync 0x10
#define SID_WBus16 0x20
#define SID_WBus32 0x40
#define SID_RelAdr 0x80
#define SID_VENDOR_SIZE 8
char vendor[SID_VENDOR_SIZE];
#define SID_PRODUCT_SIZE 16
char product[SID_PRODUCT_SIZE];
#define SID_REVISION_SIZE 4
char revision[SID_REVISION_SIZE];
/*
* The following fields were taken from SCSI Primary Commands - 2
* (SPC-2) Revision 14, Dated 11 November 1999
*/
#define SID_VENDOR_SPECIFIC_0_SIZE 20
u_int8_t vendor_specific0[SID_VENDOR_SPECIFIC_0_SIZE];
/*
* An extension of SCSI Parallel Specific Values
*/
#define SID_SPI_IUS 0x01
#define SID_SPI_QAS 0x02
#define SID_SPI_CLOCK_ST 0x00
#define SID_SPI_CLOCK_DT 0x04
#define SID_SPI_CLOCK_DT_ST 0x0C
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
#define SID_SPI_MASK 0x0F
u_int8_t spi3data;
u_int8_t reserved2;
/*
* Version Descriptors, stored 2 byte values.
*/
u_int8_t version1[2];
u_int8_t version2[2];
u_int8_t version3[2];
u_int8_t version4[2];
u_int8_t version5[2];
u_int8_t version6[2];
u_int8_t version7[2];
u_int8_t version8[2];
u_int8_t reserved3[22];
#define SID_VENDOR_SPECIFIC_1_SIZE 160
u_int8_t vendor_specific1[SID_VENDOR_SPECIFIC_1_SIZE];
};
struct scsi_vpd_supported_page_list
{
u_int8_t device;
u_int8_t page_code;
Add Serial Management Protocol (SMP) passthrough support to CAM. This includes support in the kernel, camcontrol(8), libcam and the mps(4) driver for SMP passthrough. The CAM SCSI probe code has been modified to fetch Inquiry VPD page 0x00 to determine supported pages, and will now fetch page 0x83 in addition to page 0x80 if supported. Add two new CAM CCBs, XPT_SMP_IO, and XPT_GDEV_ADVINFO. The SMP CCB is intended for SMP requests and responses. The ADVINFO is currently used to fetch cached VPD page 0x83 data from the transport layer, but is intended to be extensible to fetch other types of device-specific data. SMP-only devices are not currently represented in the CAM topology, and so the current semantics are that the SIM will route SMP CCBs to either the addressed device, if it contains an SMP target, or its parent, if it contains an SMP target. (This is noted in cam_ccb.h, since it will change later once we have the ability to have SMP-only devices in CAM's topology.) smp_all.c, smp_all.h: New helper routines for SMP. This includes SMP request building routines, response parsing routines, error decoding routines, and structure definitions for a number of SMP commands. libcam/Makefile: Add smp_all.c to libcam, so that SMP functionality is available to userland applications. camcontrol.8, camcontrol.c: Add smp passthrough support to camcontrol. Several new subcommands are now available: 'smpcmd' functions much like 'cmd', except that it allows the user to send generic SMP commands. 'smprg' sends the SMP report general command, and displays the decoded output. It will automatically fetch extended output if it is available. 'smppc' sends the SMP phy control command, with any number of potential options. Among other things, this allows the user to reset a phy on a SAS expander, or disable a phy on an expander. 'smpmaninfo' sends the SMP report manufacturer information and displays the decoded output. 'smpphylist' displays a list of phys on an expander, and the CAM devices attached to those phys, if any. cam.h, cam.c: Add a status value for SMP errors (CAM_SMP_STATUS_ERROR). Add a missing description for CAM_SCSI_IT_NEXUS_LOST. Add support for SMP commands to cam_error_string(). cam_ccb.h: Rename the CAM_DIR_RESV flag to CAM_DIR_BOTH. SMP commands are by nature bi-directional, and we may need to support bi-directional SCSI commands later. Add the XPT_SMP_IO CCB. Since SMP commands are bi-directional, there are pointers for both the request and response. Add a fill routine for SMP CCBs. Add the XPT_GDEV_ADVINFO CCB. This is currently used to fetch cached page 0x83 data from the transport later, but is extensible to fetch many other types of data. cam_periph.c: Add support in cam_periph_mapmem() for XPT_SMP_IO and XPT_GDEV_ADVINFO CCBs. cam_xpt.c: Add support for executing XPT_SMP_IO CCBs. cam_xpt_internal.h: Add fields for VPD pages 0x00 and 0x83 in struct cam_ed. scsi_all.c: Add scsi_get_sas_addr(), a function that parses VPD page 0x83 data and pulls out a SAS address. scsi_all.h: Add VPD page 0x00 and 0x83 structures, and a prototype for scsi_get_sas_addr(). scsi_pass.c: Add support for mapping buffers in XPT_SMP_IO and XPT_GDEV_ADVINFO CCBs. scsi_xpt.c: In the SCSI probe code, first ask the device for VPD page 0x00. If any VPD pages are supported, that page is required to be implemented. Based on the response, we may probe for the serial number (page 0x80) or device id (page 0x83). Add support for the XPT_GDEV_ADVINFO CCB. sys/conf/files: Add smp_all.c. mps.c: Add support for passing in a uio in mps_map_command(), so we can map a S/G list at once. Add support for SMP passthrough commands in mps_data_cb(). SMP is a special case, because the first buffer in the S/G list is outbound and the second buffer is inbound. Add support for warning the user if the busdma code comes back with more buffers than will work for the command. This will, for example, help the user determine why an SMP command failed if busdma comes back with three buffers. mps_pci.c: Add sys/uio.h. mps_sas.c: Add the SAS address and the parent handle to the list of fields we pull from device page 0 and cache in struct mpssas_target. These are needed for SMP passthrough. Add support for the XPT_SMP_IO CCB. For now, this CCB is routed to the addressed device if it supports SMP, or to its parent if it does not and the parent does. This is necessary because CAM does not currently support SMP-only nodes in the topology. Make SMP passthrough support conditional on __FreeBSD_version >= 900026. This will make it easier to MFC this change to the driver without MFCing the CAM changes as well. mps_user.c: Un-staticize mpi_init_sge() so we can use it for the SMP passthrough code. mpsvar.h: Add a uio and iovecs into struct mps_command for SMP passthrough commands. Add a cm_max_segs field to struct mps_command so that we can warn the user if busdma comes back with too many segments. Clear the cm_reply when a command gets freed. If it is not cleared, reply frames will eventually get freed into the pool multiple times and corrupt the pool. (This fix is from scottl.) Add a prototype for mpi_init_sge(). sys/param.h: Bump __FreeBSD_version to 900026 for the for the inclusion of the XPT_GDEV_ADVINFO and XPT_SMP_IO CAM CCBs.
2010-11-30 22:39:46 +00:00
#define SVPD_SUPPORTED_PAGE_LIST 0x00
#define SVPD_SUPPORTED_PAGES_HDR_LEN 4
u_int8_t reserved;
u_int8_t length; /* number of VPD entries */
#define SVPD_SUPPORTED_PAGES_SIZE 251
u_int8_t list[SVPD_SUPPORTED_PAGES_SIZE];
};
Add Serial Management Protocol (SMP) passthrough support to CAM. This includes support in the kernel, camcontrol(8), libcam and the mps(4) driver for SMP passthrough. The CAM SCSI probe code has been modified to fetch Inquiry VPD page 0x00 to determine supported pages, and will now fetch page 0x83 in addition to page 0x80 if supported. Add two new CAM CCBs, XPT_SMP_IO, and XPT_GDEV_ADVINFO. The SMP CCB is intended for SMP requests and responses. The ADVINFO is currently used to fetch cached VPD page 0x83 data from the transport layer, but is intended to be extensible to fetch other types of device-specific data. SMP-only devices are not currently represented in the CAM topology, and so the current semantics are that the SIM will route SMP CCBs to either the addressed device, if it contains an SMP target, or its parent, if it contains an SMP target. (This is noted in cam_ccb.h, since it will change later once we have the ability to have SMP-only devices in CAM's topology.) smp_all.c, smp_all.h: New helper routines for SMP. This includes SMP request building routines, response parsing routines, error decoding routines, and structure definitions for a number of SMP commands. libcam/Makefile: Add smp_all.c to libcam, so that SMP functionality is available to userland applications. camcontrol.8, camcontrol.c: Add smp passthrough support to camcontrol. Several new subcommands are now available: 'smpcmd' functions much like 'cmd', except that it allows the user to send generic SMP commands. 'smprg' sends the SMP report general command, and displays the decoded output. It will automatically fetch extended output if it is available. 'smppc' sends the SMP phy control command, with any number of potential options. Among other things, this allows the user to reset a phy on a SAS expander, or disable a phy on an expander. 'smpmaninfo' sends the SMP report manufacturer information and displays the decoded output. 'smpphylist' displays a list of phys on an expander, and the CAM devices attached to those phys, if any. cam.h, cam.c: Add a status value for SMP errors (CAM_SMP_STATUS_ERROR). Add a missing description for CAM_SCSI_IT_NEXUS_LOST. Add support for SMP commands to cam_error_string(). cam_ccb.h: Rename the CAM_DIR_RESV flag to CAM_DIR_BOTH. SMP commands are by nature bi-directional, and we may need to support bi-directional SCSI commands later. Add the XPT_SMP_IO CCB. Since SMP commands are bi-directional, there are pointers for both the request and response. Add a fill routine for SMP CCBs. Add the XPT_GDEV_ADVINFO CCB. This is currently used to fetch cached page 0x83 data from the transport later, but is extensible to fetch many other types of data. cam_periph.c: Add support in cam_periph_mapmem() for XPT_SMP_IO and XPT_GDEV_ADVINFO CCBs. cam_xpt.c: Add support for executing XPT_SMP_IO CCBs. cam_xpt_internal.h: Add fields for VPD pages 0x00 and 0x83 in struct cam_ed. scsi_all.c: Add scsi_get_sas_addr(), a function that parses VPD page 0x83 data and pulls out a SAS address. scsi_all.h: Add VPD page 0x00 and 0x83 structures, and a prototype for scsi_get_sas_addr(). scsi_pass.c: Add support for mapping buffers in XPT_SMP_IO and XPT_GDEV_ADVINFO CCBs. scsi_xpt.c: In the SCSI probe code, first ask the device for VPD page 0x00. If any VPD pages are supported, that page is required to be implemented. Based on the response, we may probe for the serial number (page 0x80) or device id (page 0x83). Add support for the XPT_GDEV_ADVINFO CCB. sys/conf/files: Add smp_all.c. mps.c: Add support for passing in a uio in mps_map_command(), so we can map a S/G list at once. Add support for SMP passthrough commands in mps_data_cb(). SMP is a special case, because the first buffer in the S/G list is outbound and the second buffer is inbound. Add support for warning the user if the busdma code comes back with more buffers than will work for the command. This will, for example, help the user determine why an SMP command failed if busdma comes back with three buffers. mps_pci.c: Add sys/uio.h. mps_sas.c: Add the SAS address and the parent handle to the list of fields we pull from device page 0 and cache in struct mpssas_target. These are needed for SMP passthrough. Add support for the XPT_SMP_IO CCB. For now, this CCB is routed to the addressed device if it supports SMP, or to its parent if it does not and the parent does. This is necessary because CAM does not currently support SMP-only nodes in the topology. Make SMP passthrough support conditional on __FreeBSD_version >= 900026. This will make it easier to MFC this change to the driver without MFCing the CAM changes as well. mps_user.c: Un-staticize mpi_init_sge() so we can use it for the SMP passthrough code. mpsvar.h: Add a uio and iovecs into struct mps_command for SMP passthrough commands. Add a cm_max_segs field to struct mps_command so that we can warn the user if busdma comes back with too many segments. Clear the cm_reply when a command gets freed. If it is not cleared, reply frames will eventually get freed into the pool multiple times and corrupt the pool. (This fix is from scottl.) Add a prototype for mpi_init_sge(). sys/param.h: Bump __FreeBSD_version to 900026 for the for the inclusion of the XPT_GDEV_ADVINFO and XPT_SMP_IO CAM CCBs.
2010-11-30 22:39:46 +00:00
/*
* This structure is more suited to target operation, because the
* number of supported pages is left to the user to allocate.
*/
struct scsi_vpd_supported_pages
{
u_int8_t device;
u_int8_t page_code;
u_int8_t reserved;
#define SVPD_SUPPORTED_PAGES 0x00
u_int8_t length;
u_int8_t page_list[0];
};
struct scsi_vpd_unit_serial_number
{
u_int8_t device;
u_int8_t page_code;
#define SVPD_UNIT_SERIAL_NUMBER 0x80
u_int8_t reserved;
u_int8_t length; /* serial number length */
#define SVPD_SERIAL_NUM_SIZE 251
u_int8_t serial_num[SVPD_SERIAL_NUM_SIZE];
};
Add Serial Management Protocol (SMP) passthrough support to CAM. This includes support in the kernel, camcontrol(8), libcam and the mps(4) driver for SMP passthrough. The CAM SCSI probe code has been modified to fetch Inquiry VPD page 0x00 to determine supported pages, and will now fetch page 0x83 in addition to page 0x80 if supported. Add two new CAM CCBs, XPT_SMP_IO, and XPT_GDEV_ADVINFO. The SMP CCB is intended for SMP requests and responses. The ADVINFO is currently used to fetch cached VPD page 0x83 data from the transport layer, but is intended to be extensible to fetch other types of device-specific data. SMP-only devices are not currently represented in the CAM topology, and so the current semantics are that the SIM will route SMP CCBs to either the addressed device, if it contains an SMP target, or its parent, if it contains an SMP target. (This is noted in cam_ccb.h, since it will change later once we have the ability to have SMP-only devices in CAM's topology.) smp_all.c, smp_all.h: New helper routines for SMP. This includes SMP request building routines, response parsing routines, error decoding routines, and structure definitions for a number of SMP commands. libcam/Makefile: Add smp_all.c to libcam, so that SMP functionality is available to userland applications. camcontrol.8, camcontrol.c: Add smp passthrough support to camcontrol. Several new subcommands are now available: 'smpcmd' functions much like 'cmd', except that it allows the user to send generic SMP commands. 'smprg' sends the SMP report general command, and displays the decoded output. It will automatically fetch extended output if it is available. 'smppc' sends the SMP phy control command, with any number of potential options. Among other things, this allows the user to reset a phy on a SAS expander, or disable a phy on an expander. 'smpmaninfo' sends the SMP report manufacturer information and displays the decoded output. 'smpphylist' displays a list of phys on an expander, and the CAM devices attached to those phys, if any. cam.h, cam.c: Add a status value for SMP errors (CAM_SMP_STATUS_ERROR). Add a missing description for CAM_SCSI_IT_NEXUS_LOST. Add support for SMP commands to cam_error_string(). cam_ccb.h: Rename the CAM_DIR_RESV flag to CAM_DIR_BOTH. SMP commands are by nature bi-directional, and we may need to support bi-directional SCSI commands later. Add the XPT_SMP_IO CCB. Since SMP commands are bi-directional, there are pointers for both the request and response. Add a fill routine for SMP CCBs. Add the XPT_GDEV_ADVINFO CCB. This is currently used to fetch cached page 0x83 data from the transport later, but is extensible to fetch many other types of data. cam_periph.c: Add support in cam_periph_mapmem() for XPT_SMP_IO and XPT_GDEV_ADVINFO CCBs. cam_xpt.c: Add support for executing XPT_SMP_IO CCBs. cam_xpt_internal.h: Add fields for VPD pages 0x00 and 0x83 in struct cam_ed. scsi_all.c: Add scsi_get_sas_addr(), a function that parses VPD page 0x83 data and pulls out a SAS address. scsi_all.h: Add VPD page 0x00 and 0x83 structures, and a prototype for scsi_get_sas_addr(). scsi_pass.c: Add support for mapping buffers in XPT_SMP_IO and XPT_GDEV_ADVINFO CCBs. scsi_xpt.c: In the SCSI probe code, first ask the device for VPD page 0x00. If any VPD pages are supported, that page is required to be implemented. Based on the response, we may probe for the serial number (page 0x80) or device id (page 0x83). Add support for the XPT_GDEV_ADVINFO CCB. sys/conf/files: Add smp_all.c. mps.c: Add support for passing in a uio in mps_map_command(), so we can map a S/G list at once. Add support for SMP passthrough commands in mps_data_cb(). SMP is a special case, because the first buffer in the S/G list is outbound and the second buffer is inbound. Add support for warning the user if the busdma code comes back with more buffers than will work for the command. This will, for example, help the user determine why an SMP command failed if busdma comes back with three buffers. mps_pci.c: Add sys/uio.h. mps_sas.c: Add the SAS address and the parent handle to the list of fields we pull from device page 0 and cache in struct mpssas_target. These are needed for SMP passthrough. Add support for the XPT_SMP_IO CCB. For now, this CCB is routed to the addressed device if it supports SMP, or to its parent if it does not and the parent does. This is necessary because CAM does not currently support SMP-only nodes in the topology. Make SMP passthrough support conditional on __FreeBSD_version >= 900026. This will make it easier to MFC this change to the driver without MFCing the CAM changes as well. mps_user.c: Un-staticize mpi_init_sge() so we can use it for the SMP passthrough code. mpsvar.h: Add a uio and iovecs into struct mps_command for SMP passthrough commands. Add a cm_max_segs field to struct mps_command so that we can warn the user if busdma comes back with too many segments. Clear the cm_reply when a command gets freed. If it is not cleared, reply frames will eventually get freed into the pool multiple times and corrupt the pool. (This fix is from scottl.) Add a prototype for mpi_init_sge(). sys/param.h: Bump __FreeBSD_version to 900026 for the for the inclusion of the XPT_GDEV_ADVINFO and XPT_SMP_IO CAM CCBs.
2010-11-30 22:39:46 +00:00
struct scsi_vpd_device_id
{
u_int8_t device;
u_int8_t page_code;
#define SVPD_DEVICE_ID 0x83
#define SVPD_DEVICE_ID_MAX_SIZE 0xffff
#define SVPD_DEVICE_ID_HDR_LEN 4
#define SVPD_DEVICE_ID_DESC_HDR_LEN 4
u_int8_t length[2];
u_int8_t desc_list[0];
};
struct scsi_vpd_id_descriptor
{
u_int8_t proto_codeset;
#define SCSI_PROTO_FC 0x00
#define SCSI_PROTO_SPI 0x01
#define SCSI_PROTO_SSA 0x02
#define SCSI_PROTO_1394 0x03
#define SCSI_PROTO_RDMA 0x04
#define SCSI_PROTO_iSCSI 0x05
#define SCSI_PROTO_SAS 0x06
#define SVPD_ID_PROTO_SHIFT 4
#define SVPD_ID_CODESET_BINARY 0x01
#define SVPD_ID_CODESET_ASCII 0x02
u_int8_t id_type;
#define SVPD_ID_PIV 0x80
#define SVPD_ID_ASSOC_LUN 0x00
#define SVPD_ID_ASSOC_PORT 0x10
#define SVPD_ID_ASSOC_TARGET 0x20
#define SVPD_ID_TYPE_VENDOR 0x00
#define SVPD_ID_TYPE_T10 0x01
#define SVPD_ID_TYPE_EUI64 0x02
#define SVPD_ID_TYPE_NAA 0x03
#define SVPD_ID_TYPE_RELTARG 0x04
#define SVPD_ID_TYPE_TPORTGRP 0x05
#define SVPD_ID_TYPE_LUNGRP 0x06
#define SVPD_ID_TYPE_MD5_LUN_ID 0x07
#define SVPD_ID_TYPE_SCSI_NAME 0x08
#define SVPD_ID_TYPE_MASK 0x0f
u_int8_t reserved;
u_int8_t length;
u_int8_t identifier[0];
};
struct scsi_vpd_id_t10
{
u_int8_t vendor[8];
u_int8_t vendor_spec_id[0];
};
struct scsi_vpd_id_eui64
{
u_int8_t ieee_company_id[3];
u_int8_t extension_id[5];
};
struct scsi_vpd_id_naa_basic
{
uint8_t naa;
/* big endian, packed:
uint8_t naa : 4;
uint8_t naa_desig : 4;
*/
#define SVPD_ID_NAA_IEEE_EXT 0x02
#define SVPD_ID_NAA_LOCAL_REG 0x03
#define SVPD_ID_NAA_IEEE_REG 0x05
#define SVPD_ID_NAA_IEEE_REG_EXT 0x06
uint8_t naa_data[0];
};
struct scsi_vpd_id_naa_ieee_extended_id
{
uint8_t naa;
uint8_t vendor_specific_id_a;
uint8_t ieee_company_id[3];
uint8_t vendor_specific_id_b[4];
};
struct scsi_vpd_id_naa_local_reg
{
uint8_t naa;
uint8_t local_value[7];
};
struct scsi_vpd_id_naa_ieee_reg
{
uint8_t naa;
uint8_t reg_value[7];
/* big endian, packed:
uint8_t naa_basic : 4;
uint8_t ieee_company_id_0 : 4;
uint8_t ieee_company_id_1[2];
uint8_t ieee_company_id_2 : 4;
uint8_t vendor_specific_id_0 : 4;
uint8_t vendor_specific_id_1[4];
*/
};
struct scsi_vpd_id_naa_ieee_reg_extended
{
uint8_t naa;
uint8_t reg_value[15];
/* big endian, packed:
uint8_t naa_basic : 4;
uint8_t ieee_company_id_0 : 4;
uint8_t ieee_company_id_1[2];
uint8_t ieee_company_id_2 : 4;
uint8_t vendor_specific_id_0 : 4;
uint8_t vendor_specific_id_1[4];
uint8_t vendor_specific_id_ext[8];
*/
};
struct scsi_vpd_id_rel_trgt_port_id
{
uint8_t obsolete[2];
uint8_t rel_trgt_port_id[2];
};
struct scsi_vpd_id_trgt_port_grp_id
{
uint8_t reserved[2];
uint8_t trgt_port_grp[2];
};
struct scsi_vpd_id_lun_grp_id
{
uint8_t reserved[2];
uint8_t log_unit_grp[2];
};
struct scsi_vpd_id_md5_lun_id
{
uint8_t lun_id[16];
};
struct scsi_vpd_id_scsi_name
{
uint8_t name_string[256];
};
struct scsi_read_capacity
{
u_int8_t opcode;
u_int8_t byte2;
u_int8_t addr[4];
u_int8_t unused[3];
u_int8_t control;
};
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
struct scsi_read_capacity_16
{
uint8_t opcode;
#define SRC16_SERVICE_ACTION 0x10
uint8_t service_action;
uint8_t addr[8];
uint8_t alloc_len[4];
#define SRC16_PMI 0x01
#define SRC16_RELADR 0x02
uint8_t reladr;
uint8_t control;
};
struct scsi_read_capacity_data
{
u_int8_t addr[4];
u_int8_t length[4];
};
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
struct scsi_read_capacity_data_long
{
uint8_t addr[8];
uint8_t length[4];
};
2002-06-04 17:41:47 +00:00
struct scsi_report_luns
{
uint8_t opcode;
uint8_t reserved1;
#define RPL_REPORT_DEFAULT 0x00
#define RPL_REPORT_WELLKNOWN 0x01
#define RPL_REPORT_ALL 0x02
uint8_t select_report;
uint8_t reserved2[3];
uint8_t length[4];
uint8_t reserved3;
uint8_t control;
2002-06-04 17:41:47 +00:00
};
struct scsi_report_luns_data {
u_int8_t length[4]; /* length of LUN inventory, in bytes */
u_int8_t reserved[4]; /* unused */
/*
* LUN inventory- we only support the type zero form for now.
*/
struct {
u_int8_t lundata[8];
} luns[0];
2002-06-04 17:41:47 +00:00
};
#define RPL_LUNDATA_PERIPH_BUS_MASK 0x3f
#define RPL_LUNDATA_FLAT_LUN_MASK 0x3f
#define RPL_LUNDATA_LUN_TARG_MASK 0x3f
#define RPL_LUNDATA_LUN_BUS_MASK 0xe0
#define RPL_LUNDATA_LUN_LUN_MASK 0x1f
#define RPL_LUNDATA_EXT_LEN_MASK 0x30
#define RPL_LUNDATA_EXT_EAM_MASK 0x0f
#define RPL_LUNDATA_EXT_EAM_WK 0x01
#define RPL_LUNDATA_EXT_EAM_NOT_SPEC 0x0f
2002-06-04 17:41:47 +00:00
#define RPL_LUNDATA_ATYP_MASK 0xc0 /* MBZ for type 0 lun */
#define RPL_LUNDATA_ATYP_PERIPH 0x00
#define RPL_LUNDATA_ATYP_FLAT 0x40
#define RPL_LUNDATA_ATYP_LUN 0x80
#define RPL_LUNDATA_ATYP_EXTLUN 0xc0
2002-06-04 17:41:47 +00:00
struct scsi_target_group
{
uint8_t opcode;
uint8_t service_action;
#define STG_PDF_LENGTH 0x00
#define RPL_PDF_EXTENDED 0x20
uint8_t reserved1[4];
uint8_t length[4];
uint8_t reserved2;
uint8_t control;
};
struct scsi_target_port_descriptor {
uint8_t reserved[2];
uint8_t relative_target_port_identifier[2];
uint8_t desc_list[];
};
struct scsi_target_port_group_descriptor {
uint8_t pref_state;
#define TPG_PRIMARY 0x80
#define TPG_ASYMMETRIC_ACCESS_STATE_MASK 0xf
#define TPG_ASYMMETRIC_ACCESS_OPTIMIZED 0x0
#define TPG_ASYMMETRIC_ACCESS_NONOPTIMIZED 0x1
#define TPG_ASYMMETRIC_ACCESS_STANDBY 0x2
#define TPG_ASYMMETRIC_ACCESS_UNAVAILABLE 0x3
#define TPG_ASYMMETRIC_ACCESS_LBA_DEPENDENT 0x4
#define TPG_ASYMMETRIC_ACCESS_OFFLINE 0xE
#define TPG_ASYMMETRIC_ACCESS_TRANSITIONING 0xF
uint8_t support;
#define TPG_AO_SUP 0x01
#define TPG_AN_SUP 0x02
#define TPG_S_SUP 0x04
#define TPG_U_SUP 0x08
#define TPG_LBD_SUP 0x10
#define TPG_O_SUP 0x40
#define TPG_T_SUP 0x80
uint8_t target_port_group[2];
uint8_t reserved;
uint8_t status;
uint8_t vendor_specific;
uint8_t target_port_count;
struct scsi_target_port_descriptor descriptors[];
};
struct scsi_target_group_data {
uint8_t length[4]; /* length of returned data, in bytes */
struct scsi_target_port_group_descriptor groups[];
};
struct scsi_target_group_data_extended {
uint8_t length[4]; /* length of returned data, in bytes */
uint8_t format_type; /* STG_PDF_LENGTH or RPL_PDF_EXTENDED */
uint8_t implicit_transition_time;
uint8_t reserved[2];
struct scsi_target_port_group_descriptor groups[];
};
2002-06-04 17:41:47 +00:00
struct scsi_sense_data
{
u_int8_t error_code;
#define SSD_ERRCODE 0x7F
#define SSD_CURRENT_ERROR 0x70
#define SSD_DEFERRED_ERROR 0x71
#define SSD_ERRCODE_VALID 0x80
u_int8_t segment;
u_int8_t flags;
#define SSD_KEY 0x0F
#define SSD_KEY_NO_SENSE 0x00
#define SSD_KEY_RECOVERED_ERROR 0x01
#define SSD_KEY_NOT_READY 0x02
#define SSD_KEY_MEDIUM_ERROR 0x03
#define SSD_KEY_HARDWARE_ERROR 0x04
#define SSD_KEY_ILLEGAL_REQUEST 0x05
#define SSD_KEY_UNIT_ATTENTION 0x06
#define SSD_KEY_DATA_PROTECT 0x07
#define SSD_KEY_BLANK_CHECK 0x08
#define SSD_KEY_Vendor_Specific 0x09
#define SSD_KEY_COPY_ABORTED 0x0a
#define SSD_KEY_ABORTED_COMMAND 0x0b
#define SSD_KEY_EQUAL 0x0c
#define SSD_KEY_VOLUME_OVERFLOW 0x0d
#define SSD_KEY_MISCOMPARE 0x0e
#define SSD_KEY_RESERVED 0x0f
#define SSD_ILI 0x20
#define SSD_EOM 0x40
#define SSD_FILEMARK 0x80
u_int8_t info[4];
u_int8_t extra_len;
u_int8_t cmd_spec_info[4];
u_int8_t add_sense_code;
u_int8_t add_sense_code_qual;
u_int8_t fru;
u_int8_t sense_key_spec[3];
#define SSD_SCS_VALID 0x80
#define SSD_FIELDPTR_CMD 0x40
#define SSD_BITPTR_VALID 0x08
#define SSD_BITPTR_VALUE 0x07
#define SSD_MIN_SIZE 18
u_int8_t extra_bytes[14];
#define SSD_FULL_SIZE sizeof(struct scsi_sense_data)
};
struct scsi_mode_header_6
{
u_int8_t data_length; /* Sense data length */
u_int8_t medium_type;
u_int8_t dev_spec;
u_int8_t blk_desc_len;
};
struct scsi_mode_header_10
{
u_int8_t data_length[2];/* Sense data length */
u_int8_t medium_type;
u_int8_t dev_spec;
u_int8_t unused[2];
u_int8_t blk_desc_len[2];
};
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
struct scsi_mode_page_header
{
u_int8_t page_code;
u_int8_t page_length;
};
struct scsi_mode_blk_desc
{
u_int8_t density;
u_int8_t nblocks[3];
u_int8_t reserved;
u_int8_t blklen[3];
};
#define SCSI_DEFAULT_DENSITY 0x00 /* use 'default' density */
#define SCSI_SAME_DENSITY 0x7f /* use 'same' density- >= SCSI-2 only */
2002-06-04 17:41:47 +00:00
/*
* Status Byte
*/
#define SCSI_STATUS_OK 0x00
#define SCSI_STATUS_CHECK_COND 0x02
#define SCSI_STATUS_COND_MET 0x04
#define SCSI_STATUS_BUSY 0x08
#define SCSI_STATUS_INTERMED 0x10
#define SCSI_STATUS_INTERMED_COND_MET 0x14
#define SCSI_STATUS_RESERV_CONFLICT 0x18
#define SCSI_STATUS_CMD_TERMINATED 0x22 /* Obsolete in SAM-2 */
#define SCSI_STATUS_QUEUE_FULL 0x28
#define SCSI_STATUS_ACA_ACTIVE 0x30
#define SCSI_STATUS_TASK_ABORTED 0x40
struct scsi_inquiry_pattern {
u_int8_t type;
u_int8_t media_type;
#define SIP_MEDIA_REMOVABLE 0x01
#define SIP_MEDIA_FIXED 0x02
const char *vendor;
const char *product;
const char *revision;
};
struct scsi_static_inquiry_pattern {
u_int8_t type;
u_int8_t media_type;
char vendor[SID_VENDOR_SIZE+1];
char product[SID_PRODUCT_SIZE+1];
char revision[SID_REVISION_SIZE+1];
};
struct scsi_sense_quirk_entry {
struct scsi_inquiry_pattern inq_pat;
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
int num_sense_keys;
int num_ascs;
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
struct sense_key_table_entry *sense_key_info;
struct asc_table_entry *asc_info;
};
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
struct sense_key_table_entry {
u_int8_t sense_key;
u_int32_t action;
const char *desc;
};
struct asc_table_entry {
u_int8_t asc;
u_int8_t ascq;
u_int32_t action;
const char *desc;
};
struct op_table_entry {
u_int8_t opcode;
u_int32_t opmask;
const char *desc;
};
struct scsi_op_quirk_entry {
struct scsi_inquiry_pattern inq_pat;
int num_ops;
struct op_table_entry *op_table;
};
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
typedef enum {
SSS_FLAG_NONE = 0x00,
SSS_FLAG_PRINT_COMMAND = 0x01
} scsi_sense_string_flags;
struct ccb_scsiio;
struct cam_periph;
union ccb;
#ifndef _KERNEL
struct cam_device;
#endif
extern const char *scsi_sense_key_text[];
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
struct sbuf;
__BEGIN_DECLS
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
void scsi_sense_desc(int sense_key, int asc, int ascq,
struct scsi_inquiry_data *inq_data,
const char **sense_key_desc, const char **asc_desc);
scsi_sense_action scsi_error_action(struct ccb_scsiio* csio,
struct scsi_inquiry_data *inq_data,
u_int32_t sense_flags);
const char * scsi_status_string(struct ccb_scsiio *csio);
#ifdef _KERNEL
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
int scsi_command_string(struct ccb_scsiio *csio, struct sbuf *sb);
int scsi_sense_sbuf(struct ccb_scsiio *csio, struct sbuf *sb,
scsi_sense_string_flags flags);
char * scsi_sense_string(struct ccb_scsiio *csio,
char *str, int str_len);
void scsi_sense_print(struct ccb_scsiio *csio);
int scsi_interpret_sense(union ccb *ccb,
u_int32_t sense_flags,
u_int32_t *relsim_flags,
u_int32_t *reduction,
u_int32_t *timeout,
scsi_sense_action error_action);
Rewrite of the CAM error recovery code. Some of the major changes include: - The SCSI error handling portion of cam_periph_error() has been broken out into a number of subfunctions to better modularize the code that handles the hierarchy of SCSI errors. As a result, the code is now much easier to read. - String handling and error printing has been significantly revamped. We now use sbufs to do string formatting instead of using printfs (for the kernel) and snprintf/strncat (for userland) as before. There is a new catchall error printing routine, cam_error_print() and its string-based counterpart, cam_error_string() that allow the kernel and userland applications to pass in a CCB and have errors printed out properly, whether or not they're SCSI errors. Among other things, this helped eliminate a fair amount of duplicate code in camcontrol. We now print out more information than before, including the CAM status and SCSI status and the error recovery action taken to remedy the problem. - sbufs are now available in userland, via libsbuf. This change was necessary since most of the error printing code is shared between libcam and the kernel. - A new transfer settings interface is included in this checkin. This code is #ifdef'ed out, and is primarily intended to aid discussion with HBA driver authors on the final form the interface should take. There is example code in the ahc(4) driver that implements the HBA driver side of the new interface. The new transfer settings code won't be enabled until we're ready to switch all HBA drivers over to the new interface. src/Makefile.inc1, lib/Makefile: Add libsbuf. It must be built before libcam, since libcam uses sbuf routines. libcam/Makefile: libcam now depends on libsbuf. libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the sbuf sources from sys/kern. bsd.libnames.mk: Add LIBSBUF. camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically linked, we can't depend on the dynamic linker to pull in libsbuf. camcontrol.c: Use cam_error_print() instead of checking for CAM_SCSI_STATUS_ERROR on every failed CCB. sbuf.9: Change the prototypes for sbuf_cat() and sbuf_cpy() so that the source string is now a const char *. This is more in line wth the standard system string functions, and helps eliminate warnings when dealing with a const source buffer. Fix a typo. cam.c: Add description strings for the various CAM error status values, as well as routines to look up those strings. Add new cam_error_string() and cam_error_print() routines for userland and the kernel. cam.h: Add a new CAM flag, CAM_RETRY_SELTO. Add enumerated types for the various options available with cam_error_print() and cam_error_string(). cam_ccb.h: Add new transfer negotiation structures/types. Change inq_len in the ccb_getdev structure to be "reserved". This field has never been filled in, and will be removed when we next bump the CAM version. cam_debug.h: Fix typo. cam_periph.c: Modularize cam_periph_error(). The SCSI error handling part of cam_periph_error() is now in camperiphscsistatuserror() and camperiphscsisenseerror(). In cam_periph_lock(), increase the reference count on the periph while we wait for our lock attempt to succeed so that the periph won't go away while we're sleeping. cam_xpt.c: Add new transfer negotiation code. (ifdefed out) Add a new function, xpt_path_string(). This is a string/sbuf analog to xpt_print_path(). scsi_all.c: Revamp string handing and error printing code. We now use sbufs for much of the string formatting code. More of that code is shared between userland the kernel. scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly useful in the first place. Add a new error action, SS_REQSENSE. (Send a request sense and then retry the command.) This is useful when the controller hasn't performed autosense for some reason. Change the default actions around a bit. scsi_cd.c, scsi_da.c, scsi_pt.c, scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection timeouts shouldn't be covered by a sense flag. scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Get rid of the last vestiges of a read/write interface. libkern/bsearch.c, sys/libkern.h, conf/files: Add bsearch.c, which is needed for some of the new table lookup routines. aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if CAM_NEW_TRAN_CODE is defined. sbuf.h, subr_sbuf.c: Add the appropriate #ifdefs so sbufs can compile and run in userland. Change sbuf_printf() to use vsnprintf() instead of kvprintf(), which is only available in the kernel. Change the source string for sbuf_cpy() and sbuf_cat() to be a const char *. Add __BEGIN_DECLS and __END_DECLS around function prototypes since they're now exported to userland. kdump/mkioctls: Include stdio.h before cam.h since cam.h now includes a function with a FILE * argument. Submitted by: gibbs (mostly) Reviewed by: jdp, marcel (libsbuf makefile changes) Reviewed by: des (sbuf changes) Reviewed by: ken
2001-03-27 05:45:52 +00:00
#else /* _KERNEL */
int scsi_command_string(struct cam_device *device,
struct ccb_scsiio *csio, struct sbuf *sb);
int scsi_sense_sbuf(struct cam_device *device,
struct ccb_scsiio *csio, struct sbuf *sb,
scsi_sense_string_flags flags);
char * scsi_sense_string(struct cam_device *device,
struct ccb_scsiio *csio,
char *str, int str_len);
void scsi_sense_print(struct cam_device *device,
struct ccb_scsiio *csio, FILE *ofile);
int scsi_interpret_sense(struct cam_device *device,
union ccb *ccb,
u_int32_t sense_flags,
u_int32_t *relsim_flags,
u_int32_t *reduction,
u_int32_t *timeout,
scsi_sense_action error_action);
#endif /* _KERNEL */
#define SF_RETRY_UA 0x01
#define SF_NO_PRINT 0x02
#define SF_QUIET_IR 0x04 /* Be quiet about Illegal Request reponses */
#define SF_PRINT_ALWAYS 0x08
const char * scsi_op_desc(u_int16_t opcode,
struct scsi_inquiry_data *inq_data);
char * scsi_cdb_string(u_int8_t *cdb_ptr, char *cdb_string,
size_t len);
void scsi_print_inquiry(struct scsi_inquiry_data *inq_data);
u_int scsi_calc_syncsrate(u_int period_factor);
u_int scsi_calc_syncparam(u_int period);
Add Serial Management Protocol (SMP) passthrough support to CAM. This includes support in the kernel, camcontrol(8), libcam and the mps(4) driver for SMP passthrough. The CAM SCSI probe code has been modified to fetch Inquiry VPD page 0x00 to determine supported pages, and will now fetch page 0x83 in addition to page 0x80 if supported. Add two new CAM CCBs, XPT_SMP_IO, and XPT_GDEV_ADVINFO. The SMP CCB is intended for SMP requests and responses. The ADVINFO is currently used to fetch cached VPD page 0x83 data from the transport layer, but is intended to be extensible to fetch other types of device-specific data. SMP-only devices are not currently represented in the CAM topology, and so the current semantics are that the SIM will route SMP CCBs to either the addressed device, if it contains an SMP target, or its parent, if it contains an SMP target. (This is noted in cam_ccb.h, since it will change later once we have the ability to have SMP-only devices in CAM's topology.) smp_all.c, smp_all.h: New helper routines for SMP. This includes SMP request building routines, response parsing routines, error decoding routines, and structure definitions for a number of SMP commands. libcam/Makefile: Add smp_all.c to libcam, so that SMP functionality is available to userland applications. camcontrol.8, camcontrol.c: Add smp passthrough support to camcontrol. Several new subcommands are now available: 'smpcmd' functions much like 'cmd', except that it allows the user to send generic SMP commands. 'smprg' sends the SMP report general command, and displays the decoded output. It will automatically fetch extended output if it is available. 'smppc' sends the SMP phy control command, with any number of potential options. Among other things, this allows the user to reset a phy on a SAS expander, or disable a phy on an expander. 'smpmaninfo' sends the SMP report manufacturer information and displays the decoded output. 'smpphylist' displays a list of phys on an expander, and the CAM devices attached to those phys, if any. cam.h, cam.c: Add a status value for SMP errors (CAM_SMP_STATUS_ERROR). Add a missing description for CAM_SCSI_IT_NEXUS_LOST. Add support for SMP commands to cam_error_string(). cam_ccb.h: Rename the CAM_DIR_RESV flag to CAM_DIR_BOTH. SMP commands are by nature bi-directional, and we may need to support bi-directional SCSI commands later. Add the XPT_SMP_IO CCB. Since SMP commands are bi-directional, there are pointers for both the request and response. Add a fill routine for SMP CCBs. Add the XPT_GDEV_ADVINFO CCB. This is currently used to fetch cached page 0x83 data from the transport later, but is extensible to fetch many other types of data. cam_periph.c: Add support in cam_periph_mapmem() for XPT_SMP_IO and XPT_GDEV_ADVINFO CCBs. cam_xpt.c: Add support for executing XPT_SMP_IO CCBs. cam_xpt_internal.h: Add fields for VPD pages 0x00 and 0x83 in struct cam_ed. scsi_all.c: Add scsi_get_sas_addr(), a function that parses VPD page 0x83 data and pulls out a SAS address. scsi_all.h: Add VPD page 0x00 and 0x83 structures, and a prototype for scsi_get_sas_addr(). scsi_pass.c: Add support for mapping buffers in XPT_SMP_IO and XPT_GDEV_ADVINFO CCBs. scsi_xpt.c: In the SCSI probe code, first ask the device for VPD page 0x00. If any VPD pages are supported, that page is required to be implemented. Based on the response, we may probe for the serial number (page 0x80) or device id (page 0x83). Add support for the XPT_GDEV_ADVINFO CCB. sys/conf/files: Add smp_all.c. mps.c: Add support for passing in a uio in mps_map_command(), so we can map a S/G list at once. Add support for SMP passthrough commands in mps_data_cb(). SMP is a special case, because the first buffer in the S/G list is outbound and the second buffer is inbound. Add support for warning the user if the busdma code comes back with more buffers than will work for the command. This will, for example, help the user determine why an SMP command failed if busdma comes back with three buffers. mps_pci.c: Add sys/uio.h. mps_sas.c: Add the SAS address and the parent handle to the list of fields we pull from device page 0 and cache in struct mpssas_target. These are needed for SMP passthrough. Add support for the XPT_SMP_IO CCB. For now, this CCB is routed to the addressed device if it supports SMP, or to its parent if it does not and the parent does. This is necessary because CAM does not currently support SMP-only nodes in the topology. Make SMP passthrough support conditional on __FreeBSD_version >= 900026. This will make it easier to MFC this change to the driver without MFCing the CAM changes as well. mps_user.c: Un-staticize mpi_init_sge() so we can use it for the SMP passthrough code. mpsvar.h: Add a uio and iovecs into struct mps_command for SMP passthrough commands. Add a cm_max_segs field to struct mps_command so that we can warn the user if busdma comes back with too many segments. Clear the cm_reply when a command gets freed. If it is not cleared, reply frames will eventually get freed into the pool multiple times and corrupt the pool. (This fix is from scottl.) Add a prototype for mpi_init_sge(). sys/param.h: Bump __FreeBSD_version to 900026 for the for the inclusion of the XPT_GDEV_ADVINFO and XPT_SMP_IO CAM CCBs.
2010-11-30 22:39:46 +00:00
uint8_t * scsi_get_sas_addr(struct scsi_vpd_device_id *id, uint32_t len);
void scsi_test_unit_ready(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *),
u_int8_t tag_action,
u_int8_t sense_len, u_int32_t timeout);
void scsi_request_sense(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *),
void *data_ptr, u_int8_t dxfer_len,
u_int8_t tag_action, u_int8_t sense_len,
u_int32_t timeout);
void scsi_inquiry(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *, union ccb *),
u_int8_t tag_action, u_int8_t *inq_buf,
u_int32_t inq_len, int evpd, u_int8_t page_code,
u_int8_t sense_len, u_int32_t timeout);
void scsi_mode_sense(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *),
u_int8_t tag_action, int dbd,
u_int8_t page_code, u_int8_t page,
u_int8_t *param_buf, u_int32_t param_len,
u_int8_t sense_len, u_int32_t timeout);
Fix ATAPI/USB/Firewire CDROM drive handling in cd(4) and hopefully fix a number of related problems along the way. - Automatically detect CDROM drives that can't handle 6 byte mode sense and mode select, and adjust our command size accordingly. We have to handle this in the cd(4) driver (where the buffers are allocated), since the parameter list length is different for the 6 and 10 byte mode sense commands. - Remove MODE_SENSE and MODE_SELECT translation removed in ATAPICAM and in the umass(4) driver, since there's no way for that to work properly. - Add a quirk entry for CDROM drives that just hang when they get a 6 byte mode sense or mode select. The reason for the quirk must be documented in a PR, and all quirks must be approved by ken@FreeBSD.org. This is to make sure that we fully understand why each quirk is needed. Once the CAM_NEW_TRAN_CODE is finished, we should be able to remove any such quirks, since we'll know what protocol the drive speaks (SCSI, ATAPI, etc.) and therefore whether we should use 6 or 10 byte mode sense/select commands. - Change the way the da(4) handles the no_6_byte sysctl. There is now a per-drive sysctl to set the minimum command size for that particular disk. (Since you could have multiple disks with multiple requirements in one system.) - Loader tunable support for all the sysctls in the da(4) and cd(4) drivers. - Add a CDIOCCLOSE ioctl for cd(4) (bde pointed this out a long time ago). - Add a media validation routine (cdcheckmedia()) to the cd(4) driver, to fix some problems bde pointed out a long time ago. We now allow open() to succeed no matter what, but if we don't detect valid media, the user can only issue CDIOCCLOSE or CDIOCEJECT ioctls. - The media validation routine also reads the table of contents off the drive. We use the table of contents to implement the CDIOCPLAYTRACKS ioctl using the PLAY AUDIO MSF command. The PLAY AUDIO TRACK INDEX command that we previously used was deprecated after SCSI-2. It works in every SCSI CDROM I've tried, but doesn't seem to work on ATAPI CDROM drives. We still use the play audio track index command if we don't have a valid TOC, but I suppose it'll fail anyway in that case. - Add _len() versions of scsi_mode_sense() and scsi_mode_select() so that we can specify the minimum command length. - Fix a couple of formatting problems in the sense printing code. MFC after: 4 weeks
2003-02-21 06:19:38 +00:00
void scsi_mode_sense_len(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *),
u_int8_t tag_action, int dbd,
u_int8_t page_code, u_int8_t page,
u_int8_t *param_buf, u_int32_t param_len,
int minimum_cmd_size, u_int8_t sense_len,
u_int32_t timeout);
void scsi_mode_select(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *),
u_int8_t tag_action, int scsi_page_fmt,
int save_pages, u_int8_t *param_buf,
u_int32_t param_len, u_int8_t sense_len,
u_int32_t timeout);
Fix ATAPI/USB/Firewire CDROM drive handling in cd(4) and hopefully fix a number of related problems along the way. - Automatically detect CDROM drives that can't handle 6 byte mode sense and mode select, and adjust our command size accordingly. We have to handle this in the cd(4) driver (where the buffers are allocated), since the parameter list length is different for the 6 and 10 byte mode sense commands. - Remove MODE_SENSE and MODE_SELECT translation removed in ATAPICAM and in the umass(4) driver, since there's no way for that to work properly. - Add a quirk entry for CDROM drives that just hang when they get a 6 byte mode sense or mode select. The reason for the quirk must be documented in a PR, and all quirks must be approved by ken@FreeBSD.org. This is to make sure that we fully understand why each quirk is needed. Once the CAM_NEW_TRAN_CODE is finished, we should be able to remove any such quirks, since we'll know what protocol the drive speaks (SCSI, ATAPI, etc.) and therefore whether we should use 6 or 10 byte mode sense/select commands. - Change the way the da(4) handles the no_6_byte sysctl. There is now a per-drive sysctl to set the minimum command size for that particular disk. (Since you could have multiple disks with multiple requirements in one system.) - Loader tunable support for all the sysctls in the da(4) and cd(4) drivers. - Add a CDIOCCLOSE ioctl for cd(4) (bde pointed this out a long time ago). - Add a media validation routine (cdcheckmedia()) to the cd(4) driver, to fix some problems bde pointed out a long time ago. We now allow open() to succeed no matter what, but if we don't detect valid media, the user can only issue CDIOCCLOSE or CDIOCEJECT ioctls. - The media validation routine also reads the table of contents off the drive. We use the table of contents to implement the CDIOCPLAYTRACKS ioctl using the PLAY AUDIO MSF command. The PLAY AUDIO TRACK INDEX command that we previously used was deprecated after SCSI-2. It works in every SCSI CDROM I've tried, but doesn't seem to work on ATAPI CDROM drives. We still use the play audio track index command if we don't have a valid TOC, but I suppose it'll fail anyway in that case. - Add _len() versions of scsi_mode_sense() and scsi_mode_select() so that we can specify the minimum command length. - Fix a couple of formatting problems in the sense printing code. MFC after: 4 weeks
2003-02-21 06:19:38 +00:00
void scsi_mode_select_len(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *),
u_int8_t tag_action, int scsi_page_fmt,
int save_pages, u_int8_t *param_buf,
u_int32_t param_len, int minimum_cmd_size,
u_int8_t sense_len, u_int32_t timeout);
void scsi_log_sense(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *, union ccb *),
u_int8_t tag_action, u_int8_t page_code,
u_int8_t page, int save_pages, int ppc,
u_int32_t paramptr, u_int8_t *param_buf,
u_int32_t param_len, u_int8_t sense_len,
u_int32_t timeout);
void scsi_log_select(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *), u_int8_t tag_action,
u_int8_t page_code, int save_pages,
int pc_reset, u_int8_t *param_buf,
u_int32_t param_len, u_int8_t sense_len,
u_int32_t timeout);
2002-06-04 17:41:47 +00:00
void scsi_prevent(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *, union ccb *),
u_int8_t tag_action, u_int8_t action,
u_int8_t sense_len, u_int32_t timeout);
void scsi_read_capacity(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *), u_int8_t tag_action,
2002-06-04 17:41:47 +00:00
struct scsi_read_capacity_data *,
u_int8_t sense_len, u_int32_t timeout);
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
void scsi_read_capacity_16(struct ccb_scsiio *csio, uint32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *), uint8_t tag_action,
uint64_t lba, int reladr, int pmi,
struct scsi_read_capacity_data_long
*rcap_buf, uint8_t sense_len,
uint32_t timeout);
2002-06-04 17:41:47 +00:00
void scsi_report_luns(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *), u_int8_t tag_action,
u_int8_t select_report,
struct scsi_report_luns_data *rpl_buf,
u_int32_t alloc_len, u_int8_t sense_len,
u_int32_t timeout);
void scsi_report_target_group(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *), u_int8_t tag_action,
u_int8_t pdf,
void *buf,
u_int32_t alloc_len, u_int8_t sense_len,
u_int32_t timeout);
void scsi_set_target_group(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *), u_int8_t tag_action, void *buf,
u_int32_t alloc_len, u_int8_t sense_len,
u_int32_t timeout);
void scsi_synchronize_cache(struct ccb_scsiio *csio,
u_int32_t retries,
void (*cbfcnp)(struct cam_periph *,
union ccb *), u_int8_t tag_action,
u_int32_t begin_lba, u_int16_t lb_count,
u_int8_t sense_len, u_int32_t timeout);
void scsi_read_write(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *, union ccb *),
u_int8_t tag_action, int readop, u_int8_t byte2,
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
int minimum_cmd_size, u_int64_t lba,
u_int32_t block_count, u_int8_t *data_ptr,
u_int32_t dxfer_len, u_int8_t sense_len,
u_int32_t timeout);
void scsi_start_stop(struct ccb_scsiio *csio, u_int32_t retries,
void (*cbfcnp)(struct cam_periph *, union ccb *),
u_int8_t tag_action, int start, int load_eject,
int immediate, u_int8_t sense_len, u_int32_t timeout);
int scsi_inquiry_match(caddr_t inqbuffer, caddr_t table_entry);
int scsi_static_inquiry_match(caddr_t inqbuffer,
caddr_t table_entry);
static __inline void scsi_extract_sense(struct scsi_sense_data *sense,
int *error_code, int *sense_key,
int *asc, int *ascq);
static __inline void scsi_ulto2b(u_int32_t val, u_int8_t *bytes);
static __inline void scsi_ulto3b(u_int32_t val, u_int8_t *bytes);
static __inline void scsi_ulto4b(u_int32_t val, u_int8_t *bytes);
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
static __inline void scsi_u64to8b(u_int64_t val, u_int8_t *bytes);
static __inline u_int32_t scsi_2btoul(u_int8_t *bytes);
static __inline u_int32_t scsi_3btoul(u_int8_t *bytes);
static __inline int32_t scsi_3btol(u_int8_t *bytes);
static __inline u_int32_t scsi_4btoul(u_int8_t *bytes);
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
static __inline u_int64_t scsi_8btou64(u_int8_t *bytes);
static __inline void *find_mode_page_6(struct scsi_mode_header_6 *mode_header);
static __inline void *find_mode_page_10(struct scsi_mode_header_10 *mode_header);
static __inline void scsi_extract_sense(struct scsi_sense_data *sense,
int *error_code, int *sense_key,
int *asc, int *ascq)
{
*error_code = sense->error_code & SSD_ERRCODE;
*sense_key = sense->flags & SSD_KEY;
*asc = (sense->extra_len >= 5) ? sense->add_sense_code : 0;
*ascq = (sense->extra_len >= 6) ? sense->add_sense_code_qual : 0;
}
static __inline void
scsi_ulto2b(u_int32_t val, u_int8_t *bytes)
{
bytes[0] = (val >> 8) & 0xff;
bytes[1] = val & 0xff;
}
static __inline void
scsi_ulto3b(u_int32_t val, u_int8_t *bytes)
{
bytes[0] = (val >> 16) & 0xff;
bytes[1] = (val >> 8) & 0xff;
bytes[2] = val & 0xff;
}
static __inline void
scsi_ulto4b(u_int32_t val, u_int8_t *bytes)
{
bytes[0] = (val >> 24) & 0xff;
bytes[1] = (val >> 16) & 0xff;
bytes[2] = (val >> 8) & 0xff;
bytes[3] = val & 0xff;
}
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
static __inline void
scsi_u64to8b(u_int64_t val, u_int8_t *bytes)
{
bytes[0] = (val >> 56) & 0xff;
bytes[1] = (val >> 48) & 0xff;
bytes[2] = (val >> 40) & 0xff;
bytes[3] = (val >> 32) & 0xff;
bytes[4] = (val >> 24) & 0xff;
bytes[5] = (val >> 16) & 0xff;
bytes[6] = (val >> 8) & 0xff;
bytes[7] = val & 0xff;
}
static __inline u_int32_t
scsi_2btoul(u_int8_t *bytes)
{
u_int32_t rv;
rv = (bytes[0] << 8) |
bytes[1];
return (rv);
}
static __inline u_int32_t
scsi_3btoul(u_int8_t *bytes)
{
u_int32_t rv;
rv = (bytes[0] << 16) |
(bytes[1] << 8) |
bytes[2];
return (rv);
}
static __inline int32_t
scsi_3btol(u_int8_t *bytes)
{
u_int32_t rc = scsi_3btoul(bytes);
if (rc & 0x00800000)
rc |= 0xff000000;
return (int32_t) rc;
}
static __inline u_int32_t
scsi_4btoul(u_int8_t *bytes)
{
u_int32_t rv;
rv = (bytes[0] << 24) |
(bytes[1] << 16) |
(bytes[2] << 8) |
bytes[3];
return (rv);
}
Add support to CAM for devices with more than 2^32 blocks. (2TB if you're using 512 byte blocks). cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to 64 bits and 32 bits respectively, so we can hold larger device sizes. cylinders would overflow at about 500GB. Bump CAM_VERSION for this change. Note that this will require a recompile of all applications that talk to the pass(4) driver. scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12) descriptions, add descriptions for SERVICE ACTION IN/OUT. Add a new function, scsi_read_capacity_16(), that issues the read capacity service action. (Necessary for arrays larger than 2^32 sectors.) Update scsi_read_write() to use a 64 bit LBA and issue READ(16) or WRITE(16) if necessary. NOTE the API change. This should be largely transparnet to most userland applications at compile time, but will break binary compatibility. The CAM_VERSION bump, above, also serves the purpose of forcing a recompile for any applications that talk to CAM. scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and scsi_8btou64. scsi_da.c: The da(4) driver probe now has two stages for devices larger than 2TB. If a standard READ CAPACITY(10) returns 0xffffffff, we issue the 16 byte version of read capacity to determine the true array capacity. We also do the same thing in daopen() -- use the 16 byte read capacity if the device is large enough. The sysctl/loader code has also been updated to accept 16 bytes as a minimum command size.
2003-04-30 00:35:22 +00:00
static __inline uint64_t
scsi_8btou64(uint8_t *bytes)
{
uint64_t rv;
rv = (((uint64_t)bytes[0]) << 56) |
(((uint64_t)bytes[1]) << 48) |
(((uint64_t)bytes[2]) << 40) |
(((uint64_t)bytes[3]) << 32) |
(((uint64_t)bytes[4]) << 24) |
(((uint64_t)bytes[5]) << 16) |
(((uint64_t)bytes[6]) << 8) |
bytes[7];
return (rv);
}
/*
* Given the pointer to a returned mode sense buffer, return a pointer to
* the start of the first mode page.
*/
static __inline void *
find_mode_page_6(struct scsi_mode_header_6 *mode_header)
{
void *page_start;
page_start = (void *)((u_int8_t *)&mode_header[1] +
mode_header->blk_desc_len);
return(page_start);
}
static __inline void *
find_mode_page_10(struct scsi_mode_header_10 *mode_header)
{
void *page_start;
page_start = (void *)((u_int8_t *)&mode_header[1] +
scsi_2btoul(mode_header->blk_desc_len));
return(page_start);
}
__END_DECLS
#endif /*_SCSI_SCSI_ALL_H*/