The documentation was quite inconsistent when spelling 'git cmd' if it
only refers to the program, not to some specific invocation syntax:
both 'git-cmd' and 'git cmd' spellings exist.
The current trend goes towards dashless forms, and there is precedent
in 647ac70 (git-svn.txt: stop using dash-form of commands.,
2009-07-07) to actively eliminate the dashed variants.
Replace 'git-cmd' with 'git cmd' throughout, except where git-shell,
git-cvsserver, git-upload-pack, git-receive-pack, and
git-upload-archive are concerned, because those really live in the
$PATH.
This only changes the behavior of "git show-ref -h" without any
other options and arguments.
"show-ref -h" currently is short for "show-ref --head", which
shows all the refs/* and HEAD, as opposed to "show-ref" that
shows all the refs/* and not HEAD.
Does anybody use "show-ref -h"? It was in Linus's original, most
likely only because "it might be handy", not because "the command
should not show the HEAD by default for such and such reasons".
So I think it is okay if "show-ref -h" (but not "show-ref
--head") gives help and exits.
If a current script uses "git show-ref -h" without any other
arguments, it would have to be adapted by changing "-h" to
"--head".
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Also make the docs more consistent with the usage message. While we're
here remove the zero initializers from the static variables as they're
unnecessary.
Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Under is better than in because of the nested nature of the .git
directory.
"also using" sounds a little odd, plus we say combined with later on so
just use that.
Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
When the SYNOPSIS says e.g. "<path>...", it is nice if the DESCRIPTION
also mentions "<path>..." and says the specified "paths" (note plural)
are used for $whatever. This fixes the obvious mismatches.
Signed-off-by: Abhijit Menon-Sen <ams@toroid.org>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
The names of git commands are not meant to be entered at the
commandline; they are just names. So we render them in italics,
as is usual for command names in manpages.
Using
doit () {
perl -e 'for (<>) { s/\`(git-[^\`.]*)\`/'\''\1'\''/g; print }'
}
for i in git*.txt config.txt diff*.txt blame*.txt fetch*.txt i18n.txt \
merge*.txt pretty*.txt pull*.txt rev*.txt urls*.txt
do
doit <"$i" >"$i+" && mv "$i+" "$i"
done
git diff
.
Signed-off-by: Jonathan Nieder <jrnieder@uchicago.edu>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Following what appears to be the predominant style, format
names of commands and commandlines both as `teletype text`.
While we're at it, add articles ("a" and "the") in some
places, italicize the name of the command in the manual page
synopsis line, and add a comma or two where it seems appropriate.
Signed-off-by: Jonathan Nieder <jrnieder@uchicago.edu>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Since the git-* commands are not installed in $(bindir), using
"git-command <parameters>" in examples in the documentation is
not a good idea. On the other hand, it is nice to be able to
refer to each command using one hyphenated word. (There is no
escaping it, anyway: man page names cannot have spaces in them.)
This patch retains the dash in naming an operation, command,
program, process, or action. Complete command lines that can
be entered at a shell (i.e., without options omitted) are
made to use the dashless form.
The changes consist only of replacing some spaces with hyphens
and vice versa. After a "s/ /-/g", the unpatched and patched
versions are identical.
Signed-off-by: Jonathan Nieder <jrnieder@uchicago.edu>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
The OPTIONS section of a documentation file contains a list
of the options a git command accepts.
Currently there are several variants to describe the case that
different options (almost) do the same in the OPTIONS section.
Some are:
-f, --foo::
-f|--foo::
-f | --foo::
But AsciiDoc has the special form:
-f::
--foo::
This patch applies this form to the documentation of the whole git suite,
and removes useless em-dash prevention, so \--foo becomes --foo.
Signed-off-by: Stephan Beyer <s-beyer@gmx.net>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
As the "git" man page describes the "git" command at the end-user
level, it seems better to move it to man section 1.
Signed-off-by: Christian Couder <chriscool@tuxfamily.org>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Between AsciiDoc 8.2.2 and 8.2.3, the following change was made to the stock
Asciidoc configuration:
@@ -149,7 +153,10 @@
# Inline macros.
# Backslash prefix required for escape processing.
# (?s) re flag for line spanning.
-(?su)[\\]?(?P<name>\w(\w|-)*?):(?P<target>\S*?)(\[(?P<attrlist>.*?)\])=
+
+# Explicit so they can be nested.
+(?su)[\\]?(?P<name>(http|https|ftp|file|mailto|callto|image|link)):(?P<target>\S*?)(\[(?P<attrlist>.*?)\])=
+
# Anchor: [[[id]]]. Bibliographic anchor.
(?su)[\\]?\[\[\[(?P<attrlist>[\w][\w-]*?)\]\]\]=anchor3
# Anchor: [[id,xreflabel]]
This default regex now matches explicit values, and unfortunately in this
case gitlink was being matched by just 'link', causing the wrong inline
macro template to be applied. By renaming the macro, we can avoid being
matched by the wrong regex.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Now that 'git peek-remote' is deprecated and only an alias for
'git ls-remote', it should not be referenced from other manual pages.
This also removes the description of the --exec option, which is no
longer present.
Signed-off-by: Johannes Sixt <johannes.sixt@telecom.at>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Use the comment in the code to document the --exclude-existing
function to git-show-ref.
Signed-off-by: Julian Phillips <julian@quantumfyre.co.uk>
Signed-off-by: Junio C Hamano <junkio@cox.net>
