The midx_bitmap_partial_tests() function is responsible for setting up a
state where some (but not all) packs in the repository are covered by a
MIDX (and bitmap).
This function has redirected the `git multi-pack-index write --bitmap`'s
stderr to a file "err" since its introduction back in c51f5a6437 (t5326:
test multi-pack bitmap behavior, 2021-08-31).
This was likely a stray change left over from a slightly different
version of this test, since the file "err" is never read after being
written. This leads to confusingly-missing output, especially when the
contents of stderr are important.
Resolve this confusion by avoiding silencing stderr in this case.
Signed-off-by: Taylor Blau <me@ttaylorr.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
When a MIDX contains the new `RIDX` chunk, ensure that the reverse index
is read from it instead of the on-disk .rev file. Since we need to
encode the object order in the MIDX itself for correctness reasons,
there is no point in storing the same data again outside of the MIDX.
So, this patch stops writing separate .rev files, and reads it out of
the MIDX itself. This is possible to do with relatively little new code,
since the format of the RIDX chunk is identical to the data in the .rev
file. In other words, we can implement this by pointing the
`revindex_data` field at the reverse index chunk of the MIDX instead of
the .rev file without any other changes.
Note that we have two knobs that are adjusted for the new tests:
GIT_TEST_MIDX_WRITE_REV and GIT_TEST_MIDX_READ_RIDX. The former controls
whether the MIDX .rev is written at all, and the latter controls whether
we read the MIDX's RIDX chunk.
Both are necessary to ensure that the test added at the beginning of
this series continues to work. This is because we always need to write
the RIDX chunk in the MIDX in order to change its checksum, but we want
to make sure reading the existing .rev file still works (since the RIDX
chunk takes precedence by default).
Arguably this isn't a very interesting mode to test, because the
precedence rules mean that we'll always read the RIDX chunk over the
.rev file. But it makes it impossible for a user to induce corruption in
their repository by adjusting the test knobs (since if we had an
either/or knob they could stop writing the RIDX chunk, allowing them to
tweak the MIDX's object order without changing its checksum).
Signed-off-by: Taylor Blau <me@ttaylorr.com>
Reviewed-by: Derrick Stolee <dstolee@microsoft.com>
Reviewed-by: Jonathan Tan <jonathantanmy@google.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
To prepare for reading the reverse index data out of the MIDX itself,
teach the `test_rev_exists` function to take an expected "source" for
the reverse index data.
When given "rev", it asserts that the MIDX's `.rev` file exists, and is
loaded when verifying the integrity of its bitmaps. Otherwise, it
ensures that trace2 reports the source of the reverse index data as the
same string which was given to test_rev_exists().
The following patch will implement reading the reverse index data from
the MIDX itself.
Signed-off-by: Taylor Blau <me@ttaylorr.com>
Reviewed-by: Derrick Stolee <dstolee@microsoft.com>
Reviewed-by: Jonathan Tan <jonathantanmy@google.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
In t5326, we have a handful of tests that we would like to run twice:
once using the MIDX's new `RIDX` chunk as the source of the
reverse-index cache, and once using the separate `.rev` file.
But because these tests mutate the state of the underlying repository,
and then make assumptions about those mutations occurring in a certain
sequence, simply running the tests twice in the same repository is
awkward.
Instead, extract the core of interesting tests into t/lib-bitmap.sh to
prepare for them to be run twice, each in a separate test script. This
means that they can each operate on a separate repository, removing any
concerns about mutating state.
For now, this patch is a strict cut-and-paste of some tests from t5326.
The tests which did not move are not interesting with respect to the
source of their reverse index data.
Signed-off-by: Taylor Blau <me@ttaylorr.com>
Reviewed-by: Derrick Stolee <dstolee@microsoft.com>
Reviewed-by: Jonathan Tan <jonathantanmy@google.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Subsequent tests will want to check for the existence of a multi-pack
bitmap which matches the multi-pack-index stored in the pack directory.
The multi-pack bitmap includes the hex checksum of the MIDX it
corresponds to in its filename (for example,
'$packdir/multi-pack-index-<checksum>.bitmap'). As a result, some tests
want a way to learn what '<checksum>' is.
This helper addresses that need by printing the checksum of the
repository's multi-pack-index.
Signed-off-by: Taylor Blau <me@ttaylorr.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
We'll soon be adding a test script that will cover many of the same
bitmap concepts as t5310, but for MIDX bitmaps. Let's pull out as many
of the applicable tests as we can so we don't have to rewrite them.
There should be no functional change to t5310; we still run the same
operations in the same order.
Signed-off-by: Taylor Blau <me@ttaylorr.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Move a function added to test-lib-functions.sh in ea047a8eb4 (t5310:
factor out bitmap traversal comparison, 2020-02-14) into a new
lib-bitmap.sh.
The test-lib-functions.sh file should be for functions that are widely
used across the test suite, if something's only used by a few tests it
makes more sense to have it in a lib-*.sh file.
Signed-off-by: Ævar Arnfjörð Bjarmason <avarab@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
